Search Documents

By Snowden C. T

B Lens Main is a scheelite orebody with an average dip of approximately 15¦ and thickness ranging from 1.5 to 6.0 m. The orebody is overlain by a banded section of ore and waste which tends to slab off if left unsupported. It was originally planned to mine a large portion of this orebody by room and pillar methods, with existing diesel trackless equipment. This, however, proved unsuitable for a number of reasons and the smaller scale method of slot stoping with hand machines and scrapers was employed. The following major problems were encountered. 1. The method was new to the mine and the work force, and had to be commenced quickly using existing or easily obtainable equipment. This is gradually being overcome by training, modification of procedures and introduction of more suitable equipment. 2. The slabbing from the hanging wall had to be controlled, either by support or by mining this low grade section and accepting the resultant dilution. This has been approached in a number of ways, depending on conditions and the method will have to be further modified as different conditions are encountered in new areas.

Jan 1, 1977

By A K. Ghosh

"Inrush of water is always an issue, especially for mines located in heavy rainfall areas. Nowadays, mining companies and research institutes have developed many advanced technologies for study and analysis of hydrological processes. In this paper, an advanced method is introduced, which uses the Shuttle Radar Topography Mission Digital Elevation Model (SRTM DEM) data in the Geographical Information System (GIS) platform to simulate the stream distributions around two specific mines: Super Pit and Griffin coalmine in Western Australia. The impact of this approach is important because it reduces the time and economic cost by creating a high spatial resolution hydrological map in the specific areas. The study identifies the flow path of the run-off water, which helps in adopting a suitable water management plan surrounding the case study mines. The results match with the ground reality. Based on the results, the stream structure around Griffin coalmine is more complicated than that of Super Pit. The bifurcation ratio and drainage density are computed to estimate the subsoil permeability characteristics of the two mines. Recommendations have been put forward to prevent and reduce the potential risks of water accumulation around the open pit mines.Citation:Ghosh, A K, 2016. Application of Shuttle Radar Topography Mission Data in Hydrological Analyses of Super Pit and Griffin Coal Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 162–169 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Sophisticated pit optimisation software has allowed mine planning engineers to generate mining outlines that consider the numerous factors that have a major effect on the success or otherwise of a mine plan. The outlines are generally generated using a range of values for which one can assume a fixed mining cost and a variable revenue. During analysis, the expected costs and revenues are used to investigate the cashflow and sensitivities. Ultimately, the final pit and incremental outlines, or shells, are selected for a given expected price. This paper proposes an alternative method for incremental pit shell selection that considers the risk the mine be prepared to accept. The life of mine is divided into a number of Business Risk Periods (BRPs). The BRP represents the period of time over which the owner is prepared to invest capital. During each BRP, the mine will then operate at a selected investment cost which is generally equal to or greater than the minimum required to meet production targets. In this way, a robust mine plan can be produced which allows the mine to react to change without having to alter the incremental shell limits while maintaining a strategic risk profile. This paper will summarise factors to be considered in selection of the BRP and the incremental pit shells within the BRP.

Jan 1, 1998

By J Eberhard, C Paton, J Bennett, C Baillie, A Melland, J F. Clewett, T Newsome

A central aim of rehabilitation is to ensure that disturbed land is returned to a post-mine condition that is safe, stable and self-sustaining. This paper describes initial results from a grazing trial at the New Acland open-cut coal mine in southern Queensland (-27.27 lat, 151.72 long) that aims to assess the sustainability and viability of cattle production from rehabilitated mined land compared to production from surrounding unmined lands (Newsome 2014). The grazing trial was established in 2013 by the Acland Pastoral Company, a subsidiary of New Hope Coal, on lands previously used for dairying, beef and crops before open cut coal mining of the Walloon coal measures began in 2002. The area has a mean annual rainfall of 640 mm. Local soils, typically dermosols and vertosols derived from sandstones or overlying basalt flows, are suited to grazing but are marginal for cropping.CITATION:Clewett, J F, Newsome, T, Paton, C, Bennett, J, Melland, A, Eberhard, J and Baillie, C, 2018. Sustainable production from rehabilitated coal mine pastures in southern Queensland’s Brigalow Region – Acland grazing trial results, in Proceedings Life-of-Mine 2018, pp 35–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By A Fern, A Hawkes, o

This presentation will cover: the importance of high-quality safety leadership; insights from a Safety Climate Survey that includes responses from 7903 employees working at 19 Australian mining organisations; the results of a critical control verification (CCV) coaching intervention; and recommendations for improving safety leadership in high-risk work settings. Safety climate is a representation of the deeper culture that exists in an organisation. Safety climate is predictive of behaviour, performance and reporting in organisations. Leaders play an important role in the establishment and maintenance of culture. Perceptions of safety climate were collected from 19 Australian mines (n = 7903 employees). These results indicate that the Australian mining sector is doing well in team support for safety and supervisor safety commitment. There were negative perceptions of willingness to report errors, employee involvement in safety initiatives, psychological safety and emergency readiness. Perceptions of safety leadership were in the fair range, with recognising behaviours perceived lowest, falling in the poor range. The underreporting rate was at 25 per cent indicating that 1 in 4 incidents are not being reported. Analyses exploring climate, leadership, safety behaviour and well-being will also be discussed. The integrity and success of critical risk management systems is often determined by the quality of safety leadership. Leaders need a mix of technical safety knowledge and interpersonal skills to be able to support the workforce to build critical control knowledge that invites open and collaborative discussions to find new or improved solutions. Forty leaders at a major mining operation completed training and 5-weeks of coaching focused on developing critical control verification competencies. The follow-up evaluation demonstrated significant improvements in relationship building, observation of controls and overall capability. Overall, insights from multi-organisation climate data and a prepost coaching intervention will be discussed and recommendations and practical guidance for leaders will be provided.

Apr 16, 2024

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

By Y Lin, B J. Seligmann, M Hassall, S Micklethwaite

For multi-site mining companies, checking the quality and consistency of the data recorded in risk registers is important for confirming how well mine safety management systems have been implemented. However, this task is complicated by the differences in scope of the site, their particular nature, the complexity of the operations and many other factors that can introduce nuances to the characteristics of the risk registers. We present here an application of a technique called Causal Network Topology Analysis for comparing the quality and consistency of risk registers. By quality we refer to, for example: - missing causal relationships between risks - location of missing controls - focus of risk treatment strategies: prevention versus mitigation controls. By consistency we refer to how causally interdependent are the risk events. There are often causal interactions between the lines of a risk register that mean that the likelihood and consequence scores that are applied to each risk event are not independent. We measure this degree of interactions by: - proportion of independent scenarios per register - efficiency of risk treatment strategy comparison. This approach can indicate quality and consistency differences between registers irrespective of the actual details of the site or operation. This occurs by comparing aspects of the structure of a causal network extracted from how the risk events, causes, controls and consequences causally interact. In this work we compare pairs of registers to demonstrate the approach.

Apr 16, 2024

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022

By R A. Pax, B Cornish

"Although it is well known and easily experienced that the feed size distribution influences the throughput and stability of operation of a semi-autogenous grinding (SAG) mill, the details are poorly understood since it is often only the input and output measurements that are used to identify unfavourable in-mill conditions. Load cells and power monitoring are sometimes used but are generally poor indicators of the mechanisms that lead to such unwanted conditions.At the MMG Century operation a 12-microphone array around the SAG mill using non-contact acoustic measurement methodology has been used to diagnose the in-mill conditions to facilitate improved throughput and stability of operation. Use of acoustic measurement and control has provided a demonstrated increased throughput of at least 20 per cent as well as improved stabilisation of the mill. Since the information derived from the acoustic noise from a mill allows discrimination of the behaviour of the steel balls and the rock, a number of in-mill conditions can be identified with signals that include toe and shoulder angles, water holdup and the ball to rock ratio.Feed size variations, measured online with an imaging system, have been used to determine their effect on the internal charge behaviour. It has been found that circumferential segregation of steel balls and rock occurs as well as poor mixing of large rocks. Both of these effects are not conducive to optimal breakage rates of different size fractions. Longitudinal segregation effects also occur. This paper presents and discusses these results and illustrates how the new acoustic knowledge can be used to manage and improve mill operation and stability.Citation:Pax, R and Cornish, B, 2016. Understanding Size Effects of Semi-autogenous Grinding (SAG) Mill Operation as a Pathway to Solving Feed Disturbances - Case Study using the MMG Century SAG Mill, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 321–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By H Kim, M J. Sun

Global steel companies are actively combating climate change by reducing carbon emissions. Traditional steel production, using the blast furnace (BF) – basic oxygen furnace (BOF) process, heavily depends on coal and emits substantial CO2. To mitigate this, companies are transitioning to the more eco-friendly DRP (direct reduction plant) – EAF (electric arc furnace) process, which lowers CO2 emissions. This study quantitatively evaluates the impact of increased hydrogen consumption on the carbon footprint of product (CFP) through an analysis of direct reduction process heat and mass balances. The study prioritises a comprehensive material balance based on mass conservation principles. The heat balance is calculated using differences in enthalpy through state energy properties, avoiding heat consumption. Validation using operational data from Hyundai Steel Dangjin works’ blast furnaces shows close alignment between calculated results and actual data, with less than 1 per cent error. This methodology facilitates a detailed analysis of the direct reduction process, offering insights into its feasibility and efficiency. Analysis of the operational impact by increasing the hydrogen ratio demonstrates reduced CO2 emissions and increased heat requirements due to the endothermic nature of hydrogen reduction, in contrast to the exothermic CO reduction. Possible solutions include raising reducing gas temperature or enhancing flow rate. The study effectively utilises designed heat and mass balances to assess material quantities and thermal balance under different operational conditions. It lays the foundation for the initial direct reduction process design, aiding in deriving and optimising operational parameters. Additionally, it provides valuable insights into the challenges of increased hydrogen, contributing to the production of greener steel by addressing these issues.

Aug 21, 2024

By M Griffiths

This paper outlines an approach to high solids slurry pipeline design with data generated from a closed pipe-loop test system. The pressure and flow rate data generated is used to develop a pseudo-shear diagram for the purposes of system design. Following this approach enables the design of a full pipe flow system maximising system life and reliability. The alternative free fall system is explained and the disadvantages highlighted.Environmental and social considerations are discussed; mainly water and land use, and how designing for high solids slurry pipeline systems can be used improve these aspects of a mining project.Also discussed is how the use of high solids slurry pipeline systems can help to mitigate the risk associated with surface tailings storage facility failure, with the Bulyanhulu project used as a positive example.

Aug 8, 2011

Five types of mineral resource were known in the sedimentary cover of the oceans and seas floors prior to the 1980's :1) hydrocarbon fields including some very large zones of oil and gas accumulation; 2) "Red Sea" type thermal oozes with increased concentrations of noble metals; 3) ferromanganese nodules; 4) concentrations of metallic sulphides ("Black Smokers"); and 5) cobalt-bearing ferromanganese crusts on the summits and slopes of seamounts. Since then, the so called "White Smokers", containing sulphides of copper and zinc, have been discovered. The ore horizons (manganese, copper, nickel and other metals) of the sedimentary cover of deep-sea basins comprise a sixth type of mineral resource in the oceans. These horizons have not only a theoretical, but also a principal economic significance

Jan 1, 1995

By S M. J Koleini, F Hedjazi

The purpose of this research was to study the calcination of lead-zinc flotation tailings from the Angouran lead and zinc flotation plant in Iran as a pre-concentration step prior to hydrometallurgical processing of the oxidised tailings. There is an abundance of these tailings in the Angouran region and making use of these tailings would help preserve national wealth and also reduce the serious problems of environmental pollution caused by the tailings. At the optimal conditions of calcining at 750 - 800¦C for 45 minutes, the sample showed a mass loss of about 19 per cent. Mineralogical analyses showed that under these conditions the carbonate minerals including smithsonite (ZnCO3), calcite (CaCO3) and dolomite (Ca Mg (CO3)2) decomposed to their respective oxides. Hemimorphite (Zn4Si2O7 (OH)2.H2O) converted into willemite (Zn2SiO4) and this transformation postponed the formation of silica gel in the leach solution. The grade of zinc increased from 22.20 per cent to 29 per cent. These mineralogical changes resulted in desirable reactions in the acid leach process.

Jan 1, 2004

By N Boughen, K Moffat, L Brooks, A Zhang

In 2015, Ernst and Young (EY) ranked socio-political license to operate (SPLTO) as the fifth greatest challenge to the mining sector (EY, 2015). The EY report asserts that SPLTO will continue to present a risk to the mining sector in the context of ‘increased activism, digitally connected stakeholders and politicians who need to respond to general consensus’. While there is no consensus on a definition, SPLTO is commonly regarded as the ongoing acceptance or approval of an operation by affected stakeholders (Moffat and Zhang, 2014; Thomson and Joyce, 2008) as well as those stakeholders that can affect the operation (Graafland, 2002). Warhurst (2001) relates the process of stakeholders granting SPLTO to the establishment of meaningful partnerships between operations, communities and government based on a variety of factors that build trust between stakeholders.From these accounts, we can see that understanding stakeholder attitudes about company performance and impacts on stakeholders directly affected by an operation are important in any attempts to measure SPLTO. Understanding the level of acceptance of an operation within these stakeholders provides a good proxy or outcome measure of SPLTO. Moreover, trust seems to be a central variable in the translation of these experiences of an operation into acceptance. What the mine or company does, its behaviour, degrades or builds trust with stakeholders, and this then affects acceptance (Moffat and Zhang, 2014).In addition, a strong emphasis is placed on the nature of the relationship between companies and stakeholders as influenced by inter-group interactions. It is not just what companies do well or poorly with respect to environmental impacts, for example, that will determine trust and acceptance, but how the company relates to its stakeholders at personal and group levels.These relationships between communities of stakeholders and extractive companies are dynamic. Brown and Fraser (2006) recognised the importance of industry being able to respond to the changing nature of societal approval and acceptance, arguing that ‘business must have regard for evolving social attitudes and expectations if it is to maintain its ‘social licence’’.This paper will describe a series of five pilot projects conducted by CSIRO with Anglo American in Australia and South Africa to generate a real-time understanding of SPLTO to guide more reflexive and effective social performance strategies.CITATION:Moffat, K, Boughen, N, Brooks, L and Zhang, A, 2016. Social licence in real-time – using dynamic methods to support a new kind of community relationship, in Proceedings Life-of-Mine 2016 Conference, pp 191–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

By R Wynn, R A. Pax, S Mann, B Cornish

The semi-autogenous grinding (SAG) mill at the MMG Century operation has failing load cells that are essential to the control strategy used to stabilise the mill. Currently, mill-bearing pressure is used as a proxy for the load cells, but it has been found to be a noisy signal and lacking in useful sensitivity. It is also prone to variations and drift due to temperature. After consideration of a number of options, a non-contact acoustic array has been installed around the SAG mill to provide a more stable proxy load signal as well as other information about the internal operation of the?mill.The installation consists of 12 microphones to provide some detail into the operational differences that occur during normal operations at the MMG Century SAG mill. This acoustic approach acknowledges that operational grinding mills emit significant acoustic emissions that are a consequence of the dynamic environment prevailing inside them.Previous studies have attributed the acoustic noise to a range of events that occur inside these mills (Pax, 2011; 2012). Consequently, non-contact acoustic determinations of in-mill behaviour can provide powerful insights into the operation of the primary comminution tumbling mills. By measuring key microphone signal attributes at different positions around a mill, a holistic picture of mill internal operation can be developed.This paper will describe the installation of the 12 microphones and discuss the use of the acoustic load signals as a proxy for failing load cells. It will also present data from new observations of internal mill dynamics and the results of implementation of control using these acoustic signals. Key to the control approach has been the development of a logically coherent picture of the processes inside the mill.CITATION:Pax, R A, Wynn, R, Mann, S and Cornish, B, 2014. Implementation of acoustic arrays for semi-autogenous grinding mill?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 273–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By C Woodall, G Jardine

The Henty Gold Mine, located in Western Tasmania uses innovative solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. This paper covers the development of a suitable paste fill system to meet the specific needs of the Henty Gold Mine and the successful commissioning of this system for the first time in Australia.

Jan 1, 1998