Search Documents

By Sparrow GJ, Woodcock JT

A sample of pyrrhotite flotation concentrate pulp assaying 15.3 g/t An, which had been prepared from an old tailing dump, was treated to extract the gold. Examination of the concentrate with an SEM showed that exposed or free native gold, 5-40 ¦m in diameter, was present but no locked gold was observed. Direct cyanidation of the concentrate to extract the gold showed that the flotation reagents present inhibited gold extraction. A range of pre-treatments was used to overcome these effects.Direct cyanidation for 48 h extracted only 26% of the gold, indicating possible contamination of the gold in the concentrate with flotation reagents. Pre-treatment of the concentrate pulp by aeration for 24 h, or by 72 h aeration with an addition of 3.65 kg/t of sodium sulphite, gave little improvement in gold extraction by subsequent cyanidation. Pre-treatment by filtration, or by aeration with 12.5 L/t 100 volume hydrogen peroxide, followed by cyanidation for 48 h gave gold extractions in the range 67-77%. Combining filtration and an aeration period with hydrogen peroxide addition raised the subsequent cyanidation extraction of gold to 88%, giving a tailing assaying 1.5 g/t Au.

Jan 1, 1990

Gold-rich porphyry copper deposits areimportant sources of gold in the circum-Pacific region: 26 major deposits contain >7000 tonnes of gold. The deposits occur in a variety of subduction-related settings, and may be underlain by crust that is undergoing either extension or compression and that is either oceanic or cratonic in character. The deposits are associated intimately with composite porphyry stocks, which commonly were emplaced into coeval andesitic volcanic piles. The stocks range in composition from low-K calc-alkaline through high-K calc-alkaline to potassic alkaline. Much of the copper and gold were introduced as components of K-silicate alteration, which may undergo partial overprinting by intermediate argillic assemblages. Advanced argillic alteration is widespread in the shallow parts of the systems whereas sericitic alteration at deeper levels tends to be restricted. Gold distribution generally follows that of copper, which is present mainly as chalcopyrite with or without bornite. The gold is in the native state and occluded by cr in close proximity to the copper-iron and/or iron sulphides. The magmas and metals necessary for the generation of gold-rich porphyry deposits were derived mainly from subcrustal sources, with the subducted slab believed to play a pivotal role.

Jan 1, 1990

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

By J Palaci, M MelTndez, F Parra, I Rojas

At the Huasco Pellet Plant of Compa±fa de Aceros del Pacffico, Chile, the production of iron concentrate suitable for pellet feed from a low-grade iron ore was technically evaluated. In this study, three treating schemes including comminution, magnetic concentration and flotation in pneumatic cells were tested. The best results were obtained at the laboratory scale by flotation technique using Lilaflot D 817 M as the collector without using any depressant. The operational parameters were determined including pneumatic flotation, and three circuits, two including magnetic pre-concentration, with the low-grade iron ore. The best results were obtained by size reduction at 80 per cent under 325 Tyler mesh, three steps of magnetic concentration and three steps of flotation in pneumatic cells. The magnetic concentrate contained 63.02 per cent of iron and 6.6 per cent of silica, and after the pneumatic flotation the iron content increased up to 70.18 per cent and silica decreases to 1.07 per cent with 78.78 per cent of iron recovery at a weight recovery of 31.89 per cent. Therefore, it is possible to use low-grade iron ore to produce pellet feed from magnetic concentrates by using reverse iron flotation in pneumatic cells.

Jan 1, 2005

By R Small, S Combrinck, R Lindsay

Maintaining your competitive edge in the growing Australian mining sector today is an arduous task. With an ever increasing demand to extract more ore, safely, complete visibility throughout the blasting cycle has become vital to any operation. To achieve this requires full two way communication with every detonator during the testing and programming cycle, as well as, inside the firing window. Concerned with an increase in the number of incidents involving mining equipment, uncovering and digging into unknown misfires on-sites across Australia, Black Star Mine made the decision to embark on the use of electronic detonators to eliminate this hazard. With this safety goal achieved, the mine set about using the added benefits of electronic detonators to improve their drill and blast processes with impressive results.CITATION:Combrinck, S, Lindsay, R and Small, R, 2012. Eliminating unidentified misfires at Xstrata ZincÆs open pits through the application of electronic detonators, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 27-30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

A paper presenting the results of studies carried out on rotary drill bit life at EluraMine N.S.W.Contributing parameters, including dataon drill operation and geology are compared to the performance observed for the drill bits. Correlation and performance characteristics are presented, relating this data to cutting size distribution over drilling depth.Details are presented of experiencegained through the operation of rotary drillsat Elura.

Jan 1, 1985

The role and policies of the Aboriginal Sacred Sites Protection Authority are described in conjunction with the provisions of the N.T Aboriginal Sacred Sites Act 1978. Comment is made on the application of the legislation and these policies to development proposals in the Northern Territory. A brief review of criticisms by both developers and Land Councils is provided together with responses to these Criticisms.

Jan 1, 1984

By J Wen, P Hou, W Yu, M Hu, Z Jiang, C Bai

Vanadium titano-magnetite (VTM) is one of the important iron ore resources in the world. High viscosity and low fluidity are the basic characteristics of hot metal containing vanadium and titanium during the ironmaking process. Clarifying the influencing mechanism of the melt viscosity would be a significant issue for the high efficiency smelting of VTM. In this paper, a self-developed melt viscometer based on the principle of torsional vibration theory was employed to measure the viscosity of hot metal accurately. Simultaneously, the thermodynamic calculations and some modern detection methods were also used to investigate the precipitation behaviour of high-melting-point phases in hot metal containing vanadium and titanium. The measuring results show that the viscosity of molten iron gradually increases with the increase of titanium content when the mass fraction of titanium is between 0.09 wt per cent – 0.50 wt per cent. Meanwhile, the viscosity of the hot metal was affected significantly by the vanadium content. When the vanadium mass fraction was higher than 0.30 wt per cent, the viscosity of hot metal increased sharply, which will have a serious impact on the fluidity of the hot metal. Furthermore, it was revealed by thermodynamic calculations that an increase in titanium and vanadium content would result in the precipitation of high melting point phases such as TiC, TiN, VC, and VN in the molten iron, ultimately resulting in a decrease in its fluidity. Meanwhile, it was confirmed by Scanning Electron Microscope (SEM) observation that the precipitates in the hot metal were compounds consisting of V, Ti, C, and N elements, which agrees well with the thermodynamic analysis results.

Aug 21, 2024

By Collier D

The topaz resource at Torrington in northern N.S.W is currently the subject of a joint research and development programme managed by Pacific Copper Ltd, This programme has culminated in a pilot topaz calcination plant, located at Parramatta, which, through its operation, will establish the commercial viability of developing this mineral as an industrial raw material for both the refractory and fluoride chemical industries.

Jan 1, 1989

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022

By Rowe J

The case study is based on the largest ore deposit at Mt. Lyell; the Prince Lyell deposit, comprising a regular lensoid mass of dissemina- ted and vein pyrite-chalcopyrite mineralisation. Reserve estimation employs conventional techniques, based on diamond drill hole and relevant development sampling data. Probable ore reserves are estimated using the contouring (isoline) method an longitudinal projections for ore thickness and accumulation (m %Cu) at a '0.8% Cu' cutoff. Final stope and pillar res- erve estimates (proved ore) are derived from designed ring tonnages and contoured accumula- tion for individual mining units, following more intensive sampling. Systematic grade control procedures have been adopted and individual stopes and pillars reconciled against mill production. The proved ore estimates have been found to com- pare favourably with the reconciled production.

Jan 1, 1979

By Tilley H. L

The 90 m deep Yallourn Open Cut brown coal mine in the Latrobe Valley, Victoria is developing into an area close to a reverse fault. A major batter stabilisation program, matched to ongoing operations, has com- menced to maximise coal recovery where the fault is within 100 m of the Open Cut. The various mine development options considered during the planning stages are outlined. These options were formulated in a back- ground of geotechnical constraints and the need to maintain continuous and reliable coal supply at a time when a new coal field would be developed. The geotechnical investigations and analysis procedures under- taken to determine stability of the batters during their excavation are presented. The geotechnical constraints on the mine design and opera- tions required to ensure safe working conditions are detailed. Current operational and batter stability conditions are considered satisfactory.

Jan 1, 1989

This paper discusses the recently com- pleted TBM-driven pressure tunnel at the Sand Bar Hydroelectric Power Project. The Sand Bar Project is a diversion scheme situated on the middle fork of the Stanislaus River in the Western Sierra Nevada, California, U.S.A. As part of the project, a 5.6 km long and 3.71 m diameter unlined pressure tunnel was bored by a Jarva TBM at the average rate of .37.5 m/ day. This report deals with construction aspects of the tunnel, including TBM performance, lining design, and remedial support measures. Correlations between TBM performance, geologic conditions, and rock properities are made, and the Contractor's mode of operations are discussed. Advance rate prediction, and the impact of these excellent advance rates attainable in hard rock using the new machines are discussed.

Jan 1, 1987

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

By P Sha

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Elaine Dorothy Cu-Au (REE-U) skarn deposit in the Mt Isa Inlier, Queensland, Australia is characterised by extensive metamorphic calc-silicate hornfels long before hydrothermal skarn and complicated deformation history. The deposit is hosted by the Corella Formation (1780–1740 Ma) and exhibits two phases of skarn formation in the study area – banded fine-grained diopsidic hornfels (Phase 1) and coarse-grain pyroxene skarn (Phase 2). Phase 1 skarn is predeformation and is interpreted to have been caused by the 1743–1734 Ma Burstall Magmatic Suites, whereas the coarse-grained pyroxene skarn (Phase 2 skarn) postdates the deformation and peak metamorphism events. Phase 2 skarn consists of prograde pyroxene, less garnet and titanite, retrograde epidote, REE-allanite, amphibole, biotite, and later sulfides, carbonate, quartz, anhydrite and chlorite. It hosts most of the copper mineralisation, with the REE elements occurring mostly in allanite. Titanite coexisting with allanite and Cu-Fe sulfides in Phase 2 skarn has been dated by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) at 1524 ± 9 Ma (207Pb/206Pb). The ages are similar to Williams-Naraku Batholiths, which outcrop approximately 40 km to the east in the Eastern Fold Belt. In Elaine Dorothy, the isotopic compositions for calcite cluster around 12.2‰ d18O and -3.7‰ d13C. It probably resulted from a mixing processes between marine sourced carbon-oxygen (ca 20‰ d18O and -0.5‰ d13C) and other distinct geochemical reservoirs, eg magmatic C-O. These features indicate that Phase 2 skarn and Cu-Au (REE-U) mineralisation may be related to unexposed intrusions at deeper levels.CITATION:Sha, P, Spandler, C and Chang, Z, 2015. Elaine Dorothy Cu-Au (REE-U) skarn deposit, in Proceedings PACRIM 2015 Congress, pp 445–450 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D Oliveira

The use of an equivalent continuum for a rock mass is not always suitable for situations where the failure is structurally controlled by discontinuities as in the case of wedges in the tunnel roof. In these instances, discontinuum approaches are usually preferred. Rock joints that are filled with soft infill are likely to be the weakest planes in a rock mass, having a dominant influence on its overall shear behaviour. In this case, the joint material model adopted for the discontinuities should be able to describe important mechanisms, such as asperity sliding and shearing, post-peak behaviour, asperity deformation, and the effect of the soft infilling. The latest version of a soil-infilled joint model is discussed here. It describes more comprehensively than previous models the occurrence of dilation and compression with lateral displacements, and also represents the hardening mechanism related to asperity interference as observed in the laboratory that cannot be readily captured by the existing joint models. An analytical approach for the analysis of rock wedges structurally controlled by soil infilled joints is presented.The analytical approach presented in this paper for assessment of symmetric rock wedges in the roof of a tunnel demonstrates, that the peak shear strength of the joint may not be fully mobilised before detachment of the wedge. The analysis verifi ed that an overestimation of the factor of safety may be observed when an elastic-perfectly-plastic joint model was assumed, whereas the computed maximum factor of safety was considerably less when adopting an appropriate soil-infilled joint model.

Mar 8, 2011

By R Williams, M Baxter, D Zink, R Cunningham

The purpose of this paper is to discuss the efficient operation of a tailings dewatering circuit comprising a thickener and filter press through proper control and automation. It is common to see thickeners and filter press circuits each with their own control systems. This can cause multiple issues when trying to increase efficiency and reliability of the tailings management process. By automating the thickener and filter press controls, you are eliminating any delays and inconsistencies caused by human error and process variations. When done properly the system can maintain a consistent product as the feed characteristics change. Previously, operators would have to monitor the process parameters and adjust the system accordingly. This can now be accomplished using state of the art process control equipment that continuously monitors and adjusts critical variables using Programmable Logic Controllers (PLC) and Proportional Integral Derivative (PID) loops. The paper will detail the control theory used to maintain these systems, highlight other benefits of having a fully integrated plant such as predictive maintenance and remote diagnostics as well as present examples of how these have been implemented in field examples.CITATION:Baxter, M, Cunningham, R, Williams, R and Zink, D, 2018. Tailings process optimisation through automation and controls integration, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 416–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

This paper is intended to continue the subject in the light of recent work, from where it was left at the conclusion of the discussion on the excellent paper by the late Mr. Noel Haszard. The position then obtaining is briefly summarised below:-The points which received general agreement at that time were:-'(1) That the gold occurs, probably in an elemental form, in a state of very fine division in the pyrite.(2) That the aim in roasting of Kalgoorlie flotation concentrates should be to obtain the maximum porosity possible. The gold tellurides were amenable to treatment with either a' solution of high lime and cyanide strength combined with fine grinding, or bybromocyanidation without re-grinding.(3) That a low roasting temperature is essential during the elimination of the first atom of sulphur, if the final calcine is to give a good extraction by cyanidation.(4) Even with the best temperature conditions of roasting then determined, and after a period of cyanidation of the calcines until no further extraction was obtainable, the lowest calcine residues obtainable were equivalent to approximately 1·8 dwts. per long ton, based on an original concentrate of pure pyrite.There was some division of opinion at the time as to whether the temperature of the later stages of roasting was significant, and also as to the reason why the initial roasting temperatures had so marked an effect.

Jan 1, 1939