Search Documents

By Robert Sisselman

Dramatic changes have been effected since 1955 in the mode of iron ore shipments within the U.S. In 1955, less than one percent of ore consumed in domestic blast furnaces-approximately 125 million long tons-consisted of pellets. Five years later, in 1960, some 94.8 million tons of ore were consumed, 14% in the form of pellets. Projections for 1980 reinforce confidence in this most economic of blast furnace feeds, and set U.S. pellet consumption at 151.2 million tons. In the last decade, pellets caught fire in other countries. By 1969, world production reached 96 million tons. This compares strikingly with present world output of 154 million tons.

Jan 9, 1973

By George C. Branner

BAUXITE is produced in Arkansas from two mining districts in the central portion of the State. These are (1) the Fourche Mountain district, immediately south and southeast of Little Rock in Pulaski County, and (2) the Bauxite (town) district, about five miles east of Becton in the eastern part of Saline County. These two mining districts are about twelve miles apart, separated by territory which, so far, has produced a negligible amount of commercial ore. Mining was by open-pit methods exclusively until 1924, when underground methods came into use. From 1924 to 1930 about 40 per cent of all of the ore produced in Arkansas was mined by underground methods, mainly by retreating caving.

Jan 1, 1935

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By Cyril Smith

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization.

Jan 1, 1935

By John J. Sense

The Mission unit of the American Smelting and Refining Co., located 20 miles south of Tucson, Ariz., is a high-volume, 15,000 tpd operation which utilizes a relatively light equipment fleet. As such, management is very conscious of the mechanical and operational availability of the equipment in use. One of the key items in attaining this efficiency is a complete and reliable record of mechanical and operational machine availability which is an invaluable guide for: 1) Estimating future equipment and personnel requirements of an operating property. 2) Planning an expansion program of an operating property. 3) Estimating equipment and personnel requirements of a new property. 4) Selection of replacement equipment. 5) Comparison of separate operating properties.

Jan 3, 1964

By N. A. Gokcen, R. A. Dodd

Solubility of nitrogen in liquid iron-manganese system at 1550°C and one atmosphere pressure has been determined by a simple method. Results show that the solubility increases from 0.040 pct for pure iron to 1.41 pct for pure manganese. DETERMINATION of the solubility of gases in volatile metals. and alloys by the well-known Sievertsl method is unreliable. This is particularly true for the Fe-Mn system since Mn vaporizes readily from the alloys containing as little as 2 pct Mn, and, upon condensing on the cooler parts of the apparatus, it absorbs large amounts of nitrogen. Further, the condensing Mn vapor interferes with the usual method of temperature measurements with an optical pyrometer.

Jan 1, 1962

By Carl Swartz

IN the course of a recent investigation1 to develop a more satisfactory white-metal. bearing alloy, a number of alloy systems were studied. The cadmium-nickel system showed characteristics desirable in a bearing alloy, and the system was therefore studied in some detail. EXPERIMENTAL METHOD Alloying cadmium with nickel offered no serious difficulty. After melting the cadmium, clean sheet nickel was added while the temperature was maintained at 500° to 600° C: A few crystals of ammonium chloride2 served to clean the nickel when the latter did not "wet" readily. In preparing the individual alloys for thermal and microscopic investigation, a "hardener" containing about 10 per cent nickel was used.

Jan 1, 1933

By Charles A. Ashburner

[The statistics contained in this paper were collected for the United States Geological Survey and communicated to the Institute, by permission, prior to their publication in the report on the Mineral Statistics of the United States for 1887.1 The total coal-production of Alabama in 1887 was about 1,950,000 short tons, the spot-value of which, at the mines, was $2,535,000. The coal-regions of the State lie in the extreme southern part of the Appalachian coal-field, the northern part of which lies along the western New York-Pennsylvania State line; between these limits, New York on the north and Alabama on the south, portions of the

Jan 1, 1889

By David M. Parkes, Junie Lindsay

A review of the movement of coal in water is undertaken from a practical rather than a theoretical view point. Installations are described in which coal is transported on gradients down to 2.5' and others which move coal at a water-coal ratio of 1:l by weight. The water cycle of the hydraulic mining system is discussed. In many applications this can be a closed circuit. The coal dewatering system is illustrated, making particular reference to the problems of storage of coal-water mixtures between the mine and the plant. Water treatment is done in thickeners down to 100 ppm which is normally sufficient for re-circulating through high pressure pumps and monitors.

Jan 1, 1978

By W. Rostoker, S. A. Spachner

FOLLOWING the discovery of the w transition phase in certain titanium-chromium alloys by Frost, Parris, Doig, and Schwartz, much interest has centered on the alloys in which this phase is found and its mode of precipitation. The w phase has been found in alloys of Ti-Cr, Ti-Fe, Ti-Mn, Ti-MO,2 and Ti-v.3 The temperature-time-transformation characteristics have, as yet, not been determined for most of these. In this study, such transformation characteristics have been investigated for two heat-treatable titanium alloys known to exhibit transition phase phenomena. The alloys chosen, Ti-8Cr and Ti-13M0, are representative of two classes of binary equilibrium systems. In the

Jan 1, 1959

By L. B. Bramlett, S. L. Reyher, G. G. Southard

The Archean (2.65 billion years) aged Canning Stock at Copper Mountain, WY, contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interibr of the stock. Post-Laramide development of supergene enrichment blankets occurred in 25-100 m (82-328 ft) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanism proposed for deposition of pitchblende are sulfides, hydro-carbons, bacteria, the water table, or some combination of these. Abundant tar-type organics appear to have preserved the enrichment blankets from degradation. Trace element and radio-metric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1983

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 (2.09 rad) apart into the outer surface of a hollow cylindrical steel, tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau of Mines on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U.S. patent (3,914,992) assigned by the author to the Dept. of the Interior was granted Oct. 28, 1975.

Jan 1, 1978

By James Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with excavator mounted upon it, which has reached a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant combining a drag-line excavator on cater-pillar mounting and a gravel-washing plant on a floating barge. The most efficient ones use a bucket of 1 to 2 yd. capacity with boom from 40 to 70 ft. long. The barge varies from 20 by 30 ft. to 36 by 48, and carries the trommel screen, pump, riffle sluices and power engine.

Jan 1, 1936

By James E. Reynolds, Duane N. Goens, Charles W. Kenney

A process for recovery of lead and silver from high-grade lead sulfide concentrates by dry chlorination and fused salt electrolysis was developed by Hazen Research, Inc., for Cyprus Metallurgical Processes Corporation (Cymet). A pilot plant was designed to handle mixed sulfide concentrates and to produce high purity lead in a 2,000- ampere capacity fused salt cell. Design of the dry chlorinator and fused salt cell is discussed. Integration of modern chlorine caustic cells for reagent generation was evaluated in the pilot plant program. Also included in the paper will be process chemistry; pilot plant flowsheet, equipment and data: by-product and impurity removal: and scaleup and economic considerations for the process.

Jan 1, 1977

By W. L. Zeigler

The gravity concentrator of the Heela Mining Co. was originally constructed in 1888 by the Milwaukee Mining Co., which was operating the Gem of the Mountains mine. It was purchased by the Hecla Mining Co. in 1900, and placed in operation 2 years later. At that time the capacity was only about 200 tons a day, but many additions and changes in equipment have been made so that the present capacity is about 800 tons. One of the outstanding improvements made was the substitution of Callow flotation cells for vanners, which occurred in 1915. The recent building of a flotation plant for treating jig tailings, and the construction of a modern surface plant at the mine, following the

Jan 1, 1928

By W. F. Mullen

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behre1 and Bowles 2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate.

Jan 12, 1951

By H. R. Hardy

The study of the mechanical properties of geologic materials was initiated in the Mining Research Section of the Fuels and Mining Practice Division in 1951 as part of a fundamental study of ground stress in Canadian coal mines.1 Early in the investigation of the mechanical properties of geologic materials, however, it was realized that the test results are influenced by the rate and the duration of loading. For this reason, laboratory investigations2,3 were undertaken to study the effect of long-period uniaxial stress on the deformation and failure properties of these materials. A literature survey indicated that work on the time-dependent properties of geologic materials had been very limited in the past.

Jan 1, 1965

By W. D. Robertson, R. E. Reed-Hill

Slip on (11221 planes, which do not contain a close-packed direction, has been identified on crystals strained at —190°C. Evidence is also presented to show that (1071) pyramidal slip is a mode of deformation at 25ºC in a limited orientation range. PYRAMIDAL slip (l011) <1120> in magnesium at elevated temperatures has been established for some time.1-2 More recently, Burke and Hibbard reported this mode of deformation at 25ºC, but their results were questioned by Craig.&apos; Also, as far as the present authors know, slip in magnesium on pyramidal planes of the second order, Type II (1122)) has not previously been reported, although Gilman"," identified (1122) slip in another hexagonal metal

Jan 1, 1959

By P. Sen

Frequently during the processing of minerals very fine particles are generated which are difficult to recover by conventional separation techniques and are rejected with waste water from mills. A method has been evolved for the continuous recovery of such fines by allowing the suspensions to flow through a rotating cylinder. Theoretical analysis of the trajectory of particles have shown that the efficiency of separation increases with R.P.M., tube diameter, particle diameter and density. Experiments carried out with the overflow from a hydrocyclone containing particles in the size range of 2-10 microns gave a separation efficiency of 60-70% with an R.P.M. of 3500 of the rotating tube.

Jan 1, 1980

By R. D. Caudle, Yoginder P. Chugh, V. K. Agarwala

Longwall coal mining is a growing mining technique in the United States. However, very little premining exploration data are collected presently by coal companies to 1) select coal winning equipment, 2) select and design face supports and supports in gate and tail entries, or 3) optimize operational parameters such as length, width, and orientation of face. The authors are of the opinion that much of the data needed for mine planning and design for longwall mining can be obtained during exploration. In this paper, the authors identify the data requirements, discuss how these data can be obtained during exploration, propose an exploration program and estimate the cost to obtain the necessary data.

Jan 1, 1982