Search Documents

By P. W. Barton, A. A. Johnson, E. J. Hughes

THE only systematic work on the effect of carbon on the recovery and recrystallization kinetics of iron so far reported in the literature is that of Venturello et al.1 These workers found that doping high-purity iron so that it contained up to 86 ppm C caused a marked retardation of recovery but had little or no effect on the recrystallization kinetics. Such evidence for an effect as was obtained was inconclusive. In the course of a study of electron-beam zone-refined iron the authors have recently examined the effect of added carbon on the recrystallization kinetics of this material. The amount of carbon added was about 50 pct more than was used by Venturello et 01. and definite evidence was obtained that carbon at this level retards recrystallization. The starting material was taken from a batch of 0.2-in.-diameter Johnson-Matthey spectroscopically pure iron rods which had been further purified by being given three passes at 4 in. hr-1 in a standard MRC electron-beam zone-refining unit. The purity of this material. which was used in two other investigations of the properties of high-purity iron,2,3 was established by an extensive series of analyses. Four laboratories, the National Research Corp., Newton, Mass., the Naval Research Laboratory, Washington, D.C.. the Battelle Memorial Institute, Columbus, Ohio, and the National Physical Laboratory. Teddington. Middlesex, England. carried out analyses for carbon. oxygen. and nitrogen. and in addition a complete mass-spectrograph analysis was carried out at Battelle. In all, twelve analyses were carried out for carbon, seventeen for oxygen and twelve for nitrogen. The amounts of these elements found to be present were 10 * 7, 8 i 5, and 0.9 i 0.1 ppm, respectively. The limits given are rms deviations. Two results, one of 46 ppm of oxygen and another of 31 ppm of nitrogen, were rejected as anomalous. The mass-spectrograph analysis revealed the major impurity to be 25 ppm of tungsten. All of the other elements detected were present in amounts less than 0.5 ppm. Some of the rods were doped with carbon by being immersed in a suspension of carbon in oil, heated in a vacuum at 400°C, and then zone-leveled to make the distribution of carbon uniform. Carbon analyses carried out on three of the doped rods gave a mean value of 130 ± 45 ppm. Some of the doped and undoped rods were deformed 58 pct by swaging and cut into specimens 1/2 in. in length. Isothermal recrystallization experiments were then carried out on them at 575", 600°, 615", 630°, and 650°C, the volume fraction of each specimen recrystallized being measured by a point-counting method described by Hilliard and Cahn.4 The results for the two types of specimens are shown separately in Figs. 1 and 2. In Fig. 3 the pairs of recrystallization curves for each temper-

Jan 1, 1965

By Strathmore R. B. Cooke, Emert W. Lindroos, Norman F. Schulz

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by' flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (--CH2CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder[4] has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate-potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality.

Jan 1, 1952

By H. Brandhorst, C. G. Dunn

THE main purpose of the present note is to provide further information on the effect of orientation on strain-induced grain boundary migration in sheet material. A secondary purpose is to draw attention to the presence of a possible (hkl) dependent surface energy driving force, when the two grains of a bicrystal specimen have different (hk2) planes at the gas-metal interface, and to suggest means of eliminating this effect from the strain effect. If two grains A and B of a bicrystal have specific surface energies ? A and ? B respectively, there exists a driving force for grain boundary migration equal to 2(? B - ? A)/t, where t is the thickness of the specimen.' When t is quite small and the residual strain energy densities €A and €B of grains A and B, respectively, adjacent to the boundary are nearly equal, it is possible that the surface effect may be larger than the strain effect. he difference € B - € A gives a driving force per unit area of grain boundary due to an applied strain.)2 However, with increasing t the surface effect decreases while the strain effect presumably remains constant. Therefore, at some sufficiently large value of t, it is possible to ignore surface energy driving forces.* On the other hand, the surface effect is eliminated for all value of t when both grains have the same (hkl) orientation or have identical values of surface energy. Although the previous study provided information on the effect of orientation on strain-induced erain boundary migration,' no orientations with the (100) plane in the plane of the sheet were included. The present paper provides information of this kind. A seed crystal reorientation technique4 was used to prepare a large bicrystal of silicon iron (3 1/4 pct Si) consisting of two (100) grains in the (100) [001] and (100) [Oil] orientations. After a cold rolling strain (7 pct reduction to 3/4 mm final thickness), small specimens were prepared as before2 and then annealed in hydrogen. The boundary migration was such that the grain in the (100) [011] orientation always grew. After overnight anneals at 1100° or 1000°C, none of the initial (100) [001] grain remained. An anneal of 30 min at 950°c, however, provided information on the start of boundary migration. Fig. 1 shows both the initial position (lower line) and the final position (upper curved line) of part of the boundary, as revealed by thermal grooves. In a different area, part of the final boundary was not revealed by thermal grooves; the rate of boundary migration presumably was too high for the growth front to be defined by the time dependent thermal grooving process. In another area there was a vacated intermediate position connected to the initial position of the grain boundary. This indicates that only part of the boundary

Jan 1, 1962

By Emma Smith, R. W. Guard

INVESTIGATION of the nickel-rich end of the Ni-Zr system has been prompted by an interest in the effect of small amounts of zirconium in high temperature alloys. Hansenl presents a hypothetical diagram based on the work of Allibone and Sykes,2 who investigated the system up to 44 atomic pct (55 wt pct) Zr by metallographic means. Since the alloys they used were melted in Alundum crucibles they were probably contaminated with appreciable amounts of aluminum. They found two compounds which they called Ni3Zr and Ni4Zr. Hayes, Roberson, and Paasche3 identified a compound NiZr (50 atomic pct Zr) with a melting point of 1470°C. Such a high melting compound is not compatible with the observation of Allibone and Sykes2 hat a eutectic is formed near 50 atomic pct. The alloys containing up to 60 atomic pct Zr were melted in an inert atmosphere in a noncon-sumable electrode arc furnace. Analysis of most of the alloys indicated negligible loss of zirconium. The alloys were examined in the as-cast condition and also after annealing for 6 hr at 1175°C (or 1000°C for the alloys between 25 atomic pct and 45 atomic pct). Metallographic specimens were etched using mixtures of HF-HNO3-H2O or acetic acid- HN0,-H,O. The specimens for the solidus determinations were wrapped in molybdenum foil and sealed in evacuated quartz tubes. Specimens to be heated above 1300°C were enclosed in zirconia tubes inside the quartz to prevent reaction with molybdenum. The solidus determinations were carried out by heating the specimens at various temperatures for a few minutes and then examining the interior structure metallographically to determine at what temperature melting began. The 150 mesh powders for X-ray analysis were annealed in an evacuated quartz tube for 2 hr at 540 °C to remove cold work. Alloys with 22.5 atomic pct Zr and 44.4 atomic pct Zr required annealing at 700 °C for complete recovery. The grains of both of these alloys were soft and rather ductile. Both Debye-Scherrer film patterns and spectrometer traces were made for each alloy using filtered copper radiation. Results and Discussion The presence of a substantial amount of second phase in an alloy with 1.1 atomic pct Zr indicated that the solid solubility of zirconium in nickel is somewhat less than 1 atomic pct. The a0 value for the face-centered-cubic matrix in the same alloy was equal to that of pure nickel, so that the solubility must be very small. This observation is as expected from the large atom size difference. Annealed specimens of alloys with 15.0, 16.7, 22.5, 28.6, 44.4, and 59.4 atomic pct Zr showed. micro-structures that were essentially single phase. When

Jan 1, 1958

By F. J. Cuddeback

For low-head pumping of small quantities of water, the water jet, or hydraulic educter, has been used to advantage by Eagle-Picher Mining and Smelting Co. in the Tri-State district. Water-jet pumps are used for draining sumps and pockets up to 15 ft. in depth. They have been used very successfully when only moderate amounts of water are encountered in taking up bottom. A small, easily handled unit is desirable in this work, especially while opening and deepening a new stope. Small air pumps are convenient but can be used only on the day shift, when air is available. Obviously, a jet pump of smaller capacity but operating 24 hr. prevents lost time at the start of each shift. No tests have been made on their power efficiency, but admittedly it is low. However, for certain kinds of work this is offset by their handiness, low initial cost, low upkeep, and reliability. They will handle slime and sand without ill effect, and will continue to pump indefinitely on air. This foolproof 24-hr. performance has led to their continued use at some places even after electric pumps with better power efficiency could have been installed. The success of jet pumps depends largely upon a cheap source of high-pressure water. Owing to mine depths in the Tri-State district, pump pressures range from 100 to 150 Ib. per sq. in. In many mines it is common practice to handle the normal inflow water with triplex pumps ranging in size from 3 to 8 in. The pumps operate 24 hr. per day, and, in order to handle emergency conditions, are speeded slightly faster than necessary to pump the normal inflow. The sump level is governed by controlling the by-pass water with a butterfly valve and float. This method is somewhat wasteful of power, but permits the pumps to operate with a minimum of attention. Such an installation is visited once a day to check lubrication. Hence, if some of this water, normally by-passed to the main sump, were used to operate a jet pump, the power cost could be considered low regardless of efficiency. Figs. I and 2 show two water jets that have done satisfactory work. The one in Fig. 2, made up entirely of pipe fittings, may be of interest partially because of its novelty, but does better work than its appearance indicates. The pipe fittings for this jet as shown cost $2.20. Some improvement in its design may be made by cutting out the 135 by 1¼-in. reducer to a smoother taper as shown by dotted lines. A 3-in. suction pipe is sometimes used in order that the discharge may be as straight as possible. A 2-in. discharge line has been used frequently, but 3-in. pipe is used where several hundred feet of discharge is required.

Jan 1, 1946

By A. J. Hatch

Recent disclosures concerning strengthening of anisotropic sheet materials under biaxial stresses are reviewed. This biaxial strengthening has been termed "texture hardening" by Backofen and is related to the normal anisotropy parameter, R. Measurements of R made on three annealed titanium alloys indicate a Ti-4Al alloy will have the greatest potential for texture hardening, followed in order by Ti-5Al-2.5Sn and Ti-6Al-4V. Relative to sheet texture, a review of the deformation mechanisms in titanium alloys would indicate that a preferred orientation for "texture hardening" is where the (0001) pole is normal to the sheet plane. This was confirmed by determination oj (0001) pole figures for the above three alloys. High R values are related to pole figures with (0001) normal to the sheet plane, whereas low R values are related to pole figures with (0001) split in the transverse direction from the sheet normal. PUBLISHED work by Backofen et al. 1 and Hosford and Backofen2 based on hill's' mathematical theory of yielding in anisotropic metals has indicated that significant strength advantages under biaxial stresses are possible in hcp alloys, provided an ideal (0001) [1010] sheet texture exists. This tendency to strengthen under biaxial stresses has been termed "texture hardening".1 It can be quantita- tively characterized by a strain-ratio parameter, R, where R may be determined from the ratio of natural width strain to natural thickness strain as measured on a uniaxial test specimen cut parallel to the rolling direction. If R is greater than 1.0, then strengthening under biaxial tension would be predicted. Considering the a titanium alloys which have an hcp crystal structure, Williams and Eppelsheimer4 have reported that commercial-purity grades deviate from the ideal (0001) sheet texture mainly in an approximate 30-deg rotation of the basal plane, toward the transverse sheet direction. However, McHargue et a1.5 have shown that the angle of rotation of the basal plane is sensitive to alloy content. In particular, a titanium alloy with 3.8 pct Al was reported to have the ideal (0001) [1010] texture after cold rolling. Additionally, Backofen et a1.1 using plane-strain compression tests have reported R values greater than 5.0 for the commercial 0 alloy Ti-5A1-2.Sn (110-AT). In view of these findings, a program was initiated to further determine the potential of commercial Ti-5A1-2.5Sn and an experimental Ti-4A1 alloy with respect to "texture hardening". Also, because of its wide commercial use, Ti-6A1-4V was included in the investigation. BIAXIAL-STRESS THEORY FOR ANISOTROPIC MATERIALS Backofen ef al.,1 based on the mathematical theory of Hi11,3 has introduced the concept of "texture hardening". In this work, it was shown that possi-

Jan 1, 1965

By Michael Poole, Joseph M. Chelini

Most earthmoving operations using off-road, rubber tired production equipment have abnormally high total tire costs. Achieving informational control over 7 direct and 2 indirect tire cost centers can reduce tire costs more than 50 percent; a 20 percent savings is often guaranteed. This is achieved by utilizing available computer software and implementing tire information management through the engineering deparatment.

Jan 1, 1983

By Kwong Yung Kwang

This mine, which is sometimes called Tong colliery, from its director, Tong King Sing, is about 80 miles northeast of Tientsin (see map, Fig. 1). Fig. 2 shows a vertical transverse section through the coal-beds. These beds have a dip to the south of about 45' and are interstratified with sandstone, shale, indurated clay and fire-clay. Of the

Jan 1, 1888

By Dan McLachlan

EXPERIMENTS on ionic solids,1 Cu-A1 alloys,2 and Fe-Si alloys3 have suggested that the ability of dislocations to cross-slip is one of the most important factors governing the nucleation and growth of fatigue cracks. These experiments necessarily had to be made on materials of different composition in order to vary the propensity for cross slip. However, re-

Jan 1, 1967

By Hannu Penttila, Harrison R. Cooper, Olli Mattila

Two approaches to automated operation in metallurgical processes involve the conventional analog control or, more recently, digital control. The expanding use of digital controls applied to process automation is a comparatively new development. Several current technical reports describe digital control systems in concentrator grinding control, 1, 2, flotation, 3 and smelter operations. 4,5 The principle factors influencing trends to digital control are:

Jan 10, 1976

By J. J. Bodmer

The four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following: 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

By A. K. Bhasin

A. K. Bhasin, (Development Engineer, Marcona Corp., San Francisco, Calif)-The author suggests the use of the term "consistency" for apparent viscosity and accordingly calls his viscometer a "consistometer." However, he goes on to refer to "consistency" as a combination of plastic viscosity, yield stress, and stability (p. 104, col. 2, line 6). Unfortunately, such conflicting terminology is encountered too often in rheological

Jan 1, 1973

By J. J. Bodmer

THE four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following : 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

Jan 1, 1874

By Igor Plaksin

Interaction of sulfide minerals and native metals with reagents in flotation is largely determined by particle-surface changes resulting from action of the medium and dissolved gases. A number of early studies were devoted to the selective action of various gases on minerals.1 Mc- Lachlan2 paid attention to oxygen as the most active gas affecting flotation properties of sulfide minerals.

Jan 3, 1959

By Magnus Troilius

The following is a very rapid method for determining copper in steel. I have found it to give results very closely agreeing with those obtained by galvanic precipitation of the copper. Five grams of steel are dissolved in a mixture of 100 C.C. of water and 10 C.C. of sulphuric acid. When all is dissolved, add 2 C.C.

Jan 1, 1883

By Luckie. Peter T., Deurbouck. A. W., Harold L. Lovell, E. R. Palowitch, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1974, 43.9% of the 603,406,000 tons (549,099,000 mt) of bituminous coal and lignite produced was cleaned mechanically, of which 82,280,000 tons (74,875,000 mt) was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 31 % between 1938 and 1974. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density inter- mediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes: 1) Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of 2 0.1 sp gr units. 2) Ability to maintain a separating gravity that can be controlled with ± 0.005 sp gr units.

Jan 1, 1979

By P. D. Merica

ALUMINUM and its alloys have been the subject of much investigation, during recent years, in the course of which the principal features of the constitution of most of the binary alloy systems with aluminum have been determined. Except in the case of a few metals-silicon, bismuth, cadmium, lead, zinc, and tin-an aluminum-rich compound is formed in each binary system, which forms a eutectic with the aluminum or its solid solution with this compound. Thus such compounds as FeAl3, CuAl2, Mg4Al3, and NiAl3 are formed, which are found in aluminum-rich alloys of their respective series as eutectics with the aluminum solid solution. These compounds are, in all cases, hard and brittle and their presence affects profoundly the physical properties of the alloys in which they occur. Within the zinc-aluminum system a compound, Al2Zn3, is formed that decomposes at lower temperatures. Silicon and tin each form a simple eutectiferous series with aluminum; bismuth, lead, and cadmium are only partly miscible in the liquid state with it. The extent of the solubility in aluminum, in solid solution, of these compounds or of the elements themselves, in the case of those series

Jan 7, 1919

By C. Schlumberger

THE object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,1 but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding?2 method, in which a series of measurements are made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is deter-

Jan 1, 1934

By R. F. Miller, R. F. Campbell

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By R. F. Campbell, R. F. Miller

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942