Search Documents

By Horace L. Wells

The gravimetric determination of titanium in irons and steels is extremely difficult. It may be well, therefore, to call the attention of those members of the Institute who are interested in the chemistry of iron to a colorimetric! method, which I have slightly elaborated to adapt it to the case under consideration. Schön * discovered that hydrogen peroxide produces, in certain solutions of titanic acid, a very intense color similar to that of ferric

Jan 1, 1886

By V. C. Allen

THE Tri-State Zinc, Inc., Galena, Ill., was confronted with the problem of securing ore from a deposit because the hoisting shaft was several thousand feet from the mill. The orebody is several thousand feet long, averaging 200 ft in width and 60 ft in height and opened up by vertical shafts some 300 ft deep. Mining is by the room-and-pillar method. During the initial operation the ore was loaded by conventional electric 1/2 -yd boom-and-dipper shovels and hauled to the shaft by 8-ton diesel trucks. This underground ore loading and hauling was well adapted to the conditions and productive of low costs per ton. However, with the mill situated as mentioned, a triple handling of all broken rock was necessary: 1-from the stope to the shaft by truck, 2-up the shaft by skip or can into the surface hopper, and 3-by truck from the surface hopper to the crushing plant at the mill. In addition to the repeated handling, serious troubles were encountered during the winter because of freezing in the shaft hopper.

Jan 6, 1951

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By John A. Fagnant

At Elkol, Wyo., about 80 miles northeast of Ogden, Utah, the Kemmerer Coal Co. and the Utah Power and Light Co. are involved in a joint venture that will soon see 1 million tons of coal going "out by wire" to Ogden. Kemmerer, owner of a multi-seam strip mine, and the utility, now building a steam power plant adjacent to the mine site, expect to begin initial power generation by February 1963. Although capable of producing only 150,000 kw at that time, this plant is expected to be ultimately enlarged to 500,000-kw capacity which will require about 2 million tons of coal annually. The deposit consists of more than 30 seams of coal, usually varying in thickness from 2 to 40 ft, and separated by beds of sandstones and shales. In certain areas the aggregate thickness of all the coal seams measures 300 ft. The thickest and most spectacular of these seams is the lowest one, referred to as the No. 1 seam, which is 118 ft thick in some places.

Jan 8, 1962

By Bruce W. Gonser, A. U. Seybolt

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By A. U. Seybolt, Bruce W. Gonser

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By W. Joseph Schlitt

The characteristics of successful heap and dump leach operations are first reviewed in a general sense. Then attention is focussed on solution management as the key operating parameter in leaching. The first part of this study includes a detailed conceptual analysis of fluid flow. This identifies the relationships between the flow parameters and the chemical and physical properties of the rock. Then these relationships are extended to practical systems in order to establish optimum application rates and solution distribution methods for heaps and dumps. The study shows that there is a maximum effective application rate, qmax, that can be used without causing solution short circuiting. This rate is a function of the minimum permeability in the heap or dump. The expression for qmax is qmax (gal/ft2/hr)[~]0.9 k (darcies). Here k is the appropriate permeability coefficient. Using this equation, qmax is found to be on the order of 1 gal/ft2/hr (4 cm/hr) for a typical heap or dump leach operation.

Jan 1, 1984

By M. L. Fuller

THE fundamental mechanism of the deformation of zinc has been thoroughly described by several prominent investigators, particularly Mark, Polanyi, and Schmid,1 Mathewson and Phillips,2 and Schmid and Wasserman.3 The deformation of zinc occurs primarily through slip along basal planes {00. 1 }, and secondarily through twinning on pyramidal planes of the form { 10.2). In addition to these basic studies on single crystals, there have been a number of determinations4,5 of preferred orientations developed in rolled, polycrystalline zinc. In no case, to our knowledge, has there been described the development of oriented struc-tures in zinc as a result of a, systematic series of rolling treatments. The work included in the present paper shows the changes in orientation produced in a zinc alloy by successively increasing degrees of cold-rolling reduction. This alloy has the same crystal form, hexagonal close-packed, as zinc, but its susceptibility to hardening for a given degree of working is much greater because of its higher recrystal-lization temperature.

Jan 1, 1934

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325.

Jan 8, 1978

By A. R. Sims

Are from the Greater Butte Project is hoisted through the new Kelley shaft. In 1946 when plans were formulated for the Kelley mine, two test cave blocks were mined by using the facilities of the old St. Lawrence mine. These blocks, known as the Adams No. 1 and Adams No. 2, produced more than half a million tons of ore. The experiment proved beyond all doubt that cave mining was possible- and economical-in Butte. Adams No. 1 was patterned after Inspiration cave blocks. Adams No. 2 was a slusher type, with the slusher lane on the first floor above the haulage crosscut and at right angles to it. Thirty-horsepower electric hoists slushed ore from 48-in. scraper buckets directly into cars for haulage to the shaft. These cars were the 57-cu ft Granby type hauled by 6-ton battery locomotives over 40-lb, 18-in. gage track. Prior to this time the largest slushing machines used at Butte were 15-hp electric hoists pulling 36-in. scrapers.

Dec 1, 1956

By N. F. Dyson, T. R. Scott, M. R. Thornber, W. E. Ewers, M. Bussell

Leach liquors derived from the processing of nickel ores are generally highly contaminated and contain appreciable free acid. Methods are described for obtaining a commercial grade of concentrate from such solutions using pyrrhotite as the seed material to abstract nick- el, cobalt, etc. from solution. At temperatures in excess of 160° C., recoveries of 99% can be obtained from contaminated solutions where the free acidity is as high as 0.5 M in sulphuric acid. At lower temperatures down to 80° C., high recoveries can also be obtained either by adding H2S to the system with appropriate adjustment of the free acidity or by using "activated" pyrrhotite or artificial FeS in the system without prior addition of H2S. The methods are applicable to liquors derived from either oxide or sulphide ores, and the products are suitable for smelting or other known processes used to obtain pure metals. The mechanism of the reaction appears to vary with the operating temperature, and the results ye therefore discussed in the light of electron probe and optical microscopic studies.

Jan 1, 1973

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By R. W. Armstrong, P. C. Jindal

The hardness dependence on grain size for polycrys-talline cartridge brass and a leaded brass has been measured by Brine11 and Rockwell B testing. In each case, the hardness, H, depends on the average grain diameter, 1, according to: H =Ho + kHl-1/2 where Ho and kH are experimental constants. Diamond pyramid hardness values have also been measured as a function of the indentation size and grain size to give additional information on the nature of the hardness test and the dependence of hardness on micro-structure. The hardness of polycrystalline brass depends on its grain size. Bassett and Davis' demonstrated this as early as 1919 by making Brinell hardness measurements on cartridge brass. Since then, the hardness of this type of material has been measured as a function of grain size by making Rockwell,2'3 Vickers,4 and Brinell5 tests. he hardness dependence on grain size has also been measured for other materials. Angus and summers6 investigated the grain size dependence of the Brinell hardness of polycrystalline copper and a Cu-4.5 pct Sn bronze. In other studies, nickel,? Armco iron,Big an Fe-0.07 pct C alloy,I0 and an 0.39 pct C-12.45 pct Cr stainless steel" have been investigated. In some of the preceding cases, the hardness results have been analyzed to show that the hardness varies with the average grain diameter, 1, according to an l-l\4, l-1/4 or I-2 dependence,11-13 The studies of the influence of grain size on hardness have not been based on any theoretical model. This may be because the hardness of a material is itself a complicated property. However, attempts have been made to correlate, experimentally and theoretically, the hardness of a material with its unidirectional stress-strain behavior.14-l6 On this basis, Hall" proposed that the polycrystal hardness dependence on grain size might follow directly from the Hall-Petch18,19 relation for the grain size dependence of the yield stress. Thus, the hardness-grain size relation was given as: H = Ho + kHl-1/2 [1] where Ho and kH were taken as experimental constants. The relation was applied to the measurements on brass,' copper,6 bronze,= and Armco iron.' More recently, this relation was shown by Armstrong and jindal20 to adequately describe the measurements on cartridge brass made by Bassett and Davis' and Babyak and Rhines.5 In this case, the relationship was taken a step further by independently relating the values of Ho and kH to the values of oyand ky, previously reported by Armstrong, Codd, Douthwaite, and petch21 from measurements of the yield stress dependence on grain size for this type of material. In the present investigation, new Brinell and Rockwell B hardness measurements have been made as a function of grain size for a cartridge brass and a leaded brass. In addition, diamond pyramid hardness values were measured as a function of the indentation size. All these results are applied to a further analysis of the hardness dependence on grain size. MATERIALS AND EXPERIMENTAL METHODS Cartridge brass and a leaded brass were selected for this investigation for two main reasons: it was anticipated 1) that these materials could be cold-worked and recrystallized to a wide range in grain size and 2) that the results to be obtained on these typical industrial materials could be usefully compared with previous investigations. The chemical analyses of the actual materials which were employed are given in Table I. The as-received 1/2- and 3/4-in.-thick plates were given various reductions in thickness by cold rolling. The rolled material was heat-treated at various temperatures between 330" and 850°C for differing time periods from 5 min to 9 hr to achieve a variation in the average grain diameter between 0.0339 and 0.000543 cm.22 During heat treatment, the brass was protected from zinc loss by packing it in chips or foils of the same composition material. Reasonably equi-axed grain structures were obtained in each case. The metallurgical grain sizes of the specimens were determined from measurements of the average linear intercept on a random line. Annealing twin interfaces were not counted along with grain boundaries. The

Jan 1, 1970

By C. S. Smith

The solubility of tantalum at 1100°C is 0.025 pct in pure copper, 1.2 pct with 20 pct Ni, and 2.7 pct with -30 pct Ni. The solubility decreases with temperature, and the alloys are precipitation hardenable. A 79/20/1 Cu-Ni-Ta alloy reaches maximum hardness after aging at about 750°C and, if cold worked, does not recrystal-lize below that temperature. The alloys have good tensile properties at moderately elevated temperatures and, since they can be hot and cold worked nearly as easily as cupronickel, they are suggested for service at temperatures above the usual limits for copper alloys. MASSIVE tantalum dissolves extremely slowly in copper-rich alloys, and tantalum powder forms refractory surface layers which prevent its solution unless special precautions are taken. After many trials, an 80 pit recovery was consistently obtained by using a mixture of a finely divided tantalum powder with two or three times its volume of potassium tantalum fluoride (K2TaF1,-melting point about 750°C) poured in a slow stream directly on to the surface of the molten copper alloy, so that each particle would remain coated with flux and be immediately and individually wetted by the molten metal. A 50-50 nickel-tantalum alloy has a melting point of about 1400°C and small lumps of it slowly but satisfactorily dissolve in molten copper-nickel alloys as does commerical "ferro-tantalum." The high affinity of tantalum for carbon makes it necessary to avoid carbonaceous crucibles. COPPER-TANTALUM ALLOYS Castings with good shrinkage resulted when 0.1 pct Ta or more was added to copper melted under charcoal and cast in air. Copper in two-pound melts to which 0.1, 0.15, and 0.2 pct Ta had been added retained residual amounts, by analysis, of 0.025, 0.023 and 0.026 pct, respectively. The solubility of tantalum in molten copper at about 1200 °C is therefore about 0.025 pct. The electrical conductivity of these three samples was 100.48, 100.00 and 100.20 pct IACS in the annealed condition, and 98.24, 97.98 and 98.08 in the cold-drawn condition. Wires 0.080 in. in diam withstood from thirteen to nineteen reversed bends after annealing for 30 min in hydrogen at 850°C and the metal was therefore completely deoxidized. The annealing temperature corresponding to 50 pct loss of work hardness in 1 hr in a strip cold rolled 77 pct reduction was 175C, compared to 230°C for equivalent undeoxidized material. It is unusual for a decrease of recrystallization temperature to result from an alloying addition, and the tantalum probably combines with and removes some minor impurity in the original copper that restrained its recrystalliza- tion. No difficulty whatever was encountered in hot or cold rolling or drawing these ingots, and were tantalum not so expensive it would make an excellent deoxidizer for copper. COPPER-NIcKEL-TANTALUM ALLOYS Studies were made of the solubility of tantalum in a large number of copper-rich alloys, but of these significant solubilities were found only in the case of an iron alloy (which, however, separated into two immiscible liquid layers) and alloys of copper and nickel, in which tantalum is freely soluble and which were found to have interesting properties. The latter alloys are the subject of U. S. Patent No. 2,430,306 (1947). They are not at present available commercially. The Ternary Constitution Diagram—The copper-rich corner of the constitution diagram was constructed on the basis of microscopic examination of samples of various composition and treatments. The alloys were hot rolled to 0.25 in. from castings 0.625 in. thick, then annealed for 1 hr at 1000°C, quenched, cold rolled to 0.10 in. and finally annealed for various periods of time at temperatures between 800" and 1100°C in a nonoxidizing atmosphere and quenched. When the solid-solubility limit had been transgressed, particles of a compound believed to be Ni2Ta*were

Jan 1, 1960

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation. A series of temporary and permanent water pumping stations is planned. Generally, the temporary stations are located above major aquifers to facilitate water removal while sinking through the aquifer and the permanent stations constitute what, in the final mode, will be the mine dewatering system. In addition, Phillips Uranium Corporation has In- stalled and is maintaining a system of depressurization wells that temporarily pump the major aquifers and considerably reduce the water inflows during shaft construction. The major aquifers are also chemically grouted prior to sinking. Site work for the project was initiated in the fall of 1976. Full scale shaft sinking commenced in November of 1977 on the 4.88 m (16 ft) diameter ventilation shaft and on the 5.49 m (18 ft) production shaft by another contractor. Harrison Western Corporation began work on the project on November 4, 1979 wlth the production shaft at a depth of 633 m (2,076 ft) and the ventilation shaft at a depth of 474 m (1,554 ft). This paper will address only the portion of shaft sinking completed by Harrison Western. Geology and Hydrology The Nose Rock Project is located on the Chaco Slope in the southern extreme of the San Juan Basin in northwest New Mexico. The southern San Juan Basin is generally bound by the Defiance Uplift to the west, the Zuni Uplift to the south and the Nacimiento Uplift to the east. The Grants Mineral Belt occupies most of the southern portion of the San Juan Basin and this project is located on the northern extreme of the Grants Mineral Belt. The San Juan Basin is comprised of sedimentary rock of continental, marginal-marine and marine origin, that dip northward from the Zuni Uplift and Chaco Slope into the interior of the San Juan Basin. (See Figure 2) Major Formations The major geologic formations to be penetrated range from mudstone and shales to siltstones and sandstones. The sandstones are highly productive aquifers which, under static conditions, would flow artesian. Water temperatures in the aquifers are high and therefore are a force to be dealt with. Temperatures range from 18ºC (65OF) in the upper aquifers to 48ºC (118º'F) in the lower. The mudstones are generally bentonitlc. (See Figure 2) GALLUP SANDSTONE: The Gallup Sandstone is the first major regressive wedge in the San Juan Basin of the Cretaceous era and at this project is about 35 m (115 ft) thick. It is medium grained and prior to depressurization carried a hydrostatic water pressure of over 72.5 kg per cm2 (1,031 psi) which 1s artesian. Compressive strength ranges from 334.7 kg per cm2 (4,760 psi) to 421.8 kg per cm2 (6,000 psi). Water temperature is approximately 30°C (86°F).

Jan 1, 1982

By C. G. Dunn, F. Lionetti

The energy associated with grain boundaries in polycrystalline aggregates is believed to play a major role in grain growth processes and, when growth ceases, to determine the final equilibrium grain boundary angles. Further, the energy of grain boundaries of recrystallization nuclei is a factor in nucleation processes. It is important to know, therefore, how the energy per unit area of a grain boundary, that is, the grain boundary surface tension y, depends on the difference in orientation of the two lattices of the grains producing the boundary. Although the problem is important, surprisingly little has been done toward a quantitative evaluation of the effect of orientation difference on grain boundary energies. C. S. Smith1 recently has discussed this problem and in addition to showing effects of orientation difference on equilibrium angles has shown a variety of interesting effects of surface tension on the appearance of microstructures. Fig 1 and the following relations expressed in Eq 1, which connect equilibrium grain boundary angles and surface tensions, illustrate equilibrium conditions which are believed to hold true in metals. ?l2 _ ?23 _ ?l3 [1] sin ?3 sin ?1 sin ?2 Clearly any two of these surface tensions can be expressed in terms of the third when the equilibrium angles ?1, ?2, and ?3 are known. Applied to the present problem for solid state equilibrium of three grains, the angles ?1,?2 and ?3 must be measured in a plane perpendicular to the line of junction of the three grains. Normally a direct determination of these angles from random microsections is impossible. Consequently Harker and Parker2 and Smith1 (except for some measurements on flat specimens) resorted to a statistical method to determine equilibrium grain boundary angles. Smith reported that grain boundaries meet the surface of a piece of metal nearly perpendicularly. He reported also, in connection with direct angle measurements on flat specimens with grains extending through the thickness, that angles varied appreciably from 120" and concluded that there was a measurable effect of orientation difference on surface tension. Another direct way of determining equilibrium angles and a method adaptable to studying particular configurations, recently suggested by Dunn,³ is to use a three-grain flat specimen with orientations of grains so chosen that the junction line of the three grains will be straight throughout the thickness and perpendicular to the surface of the specimen. Choice of orientations is possible when individual grains of each group can be grown to predetermined orientations through the reorienting and growth of " seed crystals " as described.³ Not only is it possible, for example, to have grains with the same crystallographic plane in the plane of the specimen, but a given orientation difference between two grains can be made a common factor to an unlimited number of three-grain groups while a series of orientation differences is investigated. Any effect of anisotropy of gas-solid surface tension due to grain orientation should be minimized by having all gains oriented the same with regard to crystallographic plane in the plane of the specimen. Another feature of the three-grain group is the notched grain boundaries as shown in Fig 2 for one specimen (S4). The notches serve to anchor the end positions of the grain boundaries (especially at high temperatures) while the central and junction point of the grains moves toward an equilibrium position. Final equilibrium should produce straight grain boundaries if the notches are very narrow and if changes in orientation* of the grain boundary do not alter the surface tension.† If one assumes the straight line condition and no change of surface tension with small changes in grain boundary orientation and finds the equilibrium configuration by a minimization of the grain boundary energy, one obtains the relations given in Eq 1. The approach to straight line boundaries or to minimum energy configurations in specimens containing large grains, such as those used in the present investigation, may be very slow compared with the approach to equilibrium conditions for the grain boundary angles. It may be desirable, as proved to be the case in the present investiga-

Jan 1, 1950

F. E. BASH, Philadelphia, Pa.-In order to make a definite check on the emissivity of crucible steel under works conditions, a test was planned and executed by the plant of the Midvale Steel Co., by a Sub-committee, as follows: Five crucibles were put in a crucible furnace with-the normal charge and were treated in the same manner as a number of others that were charged at the same time; the only difference was that the five cur-cibles had lids with.2-in. holes in the center. It was thought that after the crucibles were removed from the furnace a reading could be made through the hole in the lid with the optical pyrometer and that such a reading would give the true temperature of the steel as black-body con-ditions should prevail inside the crucible. If after obtaining the true temperature, the crucible lid were removed and the steel poured into the ladle, the apparent temperature could be taken by sighting on the steel stream and the emissivity obtained from the two temperature values. Such a test was carried out with five crucibles. About a third of the crucibles charged into the furnace with the five experimental ones were first drawn from the furnace and poured into the ladle. The experimental crucibles were then drawn and readings of the true temperature were made

Jan 12, 1919