Search Documents

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

By J. F. Crouch

INTRODUCTION Roll front uranium has unique geologic characteristics (L,) which require specialized mining procedures. Roll front uranium occurs in arkosic sandstones with the ore zone typically less than 100 feet in thickness with up to 400 feet of overburden. The areal extent of ore is often a few thousand acres. Within the ore zone, ore grade material occurs in C and S shaped rolls, which are a few feet in width and height but may run laterally for several hundred feet. Since the total mine plan may include mining all ore, a roll front uranium mine may cover a few thousand acres. For both economic and environmental reasons, a roll front deposit is mined as a series of phases or sub-pits (3, 4) as illustrated in Figure 1. A typical sub-pit is 400 to 500 feet across. Sub-pit 1 is stripped initially and the overburden is spoiled on the surface. Depending on haul distance and overburden characteristics, stripping is done with trucks and shovels (or front-end loaders) or scrapers. When ore is encountered in sub-pit 1, mining begins, and the stripping equipment is moved to sub-pit 2, with sub-pit 2 overburden also being spoiled on the surface. When ore is encountered in sub- pit 2, sub-pit 1 mining should ideally be complete so the mining equipment can move to sub-pit 2 and sub-pit 3 overburden can be spoiled in the mined out sub-pit 1 area. Ore is mined selectively in a series of 12 to 24 inch cuts by a 2-1/2 yard backhoe on the basis of radiometric probing. For effective drainage, ditches must be maintained on the boundary of sub-pits, and mining lifts are kept as level as possible, with the orebody slightly elevated as part of general good mining practice. Waste removal in the ore zone is done by self- loading scrapers near the orebodies and by push-pull or push loaded scrapers away from the orebodies. Each self-loading scraper cut is

Jan 1, 1983

"No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of ""boom"" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.A technical discussion of the ore occurrence and mining operations in the camp will be the subject of a paper to be read before this meeting of the Institute. The mission of this article is to supply a ""Baedeker"" where Baedeker is lacking.The town of Park City is a typical, up-to-date, western mining camp which owes its existence as a town of 4,500 inhabitants solely to the mining industry. The camp is located 7,000 feet above sea level, thirty-two miles east of Salt Lake City. It is situated on the Victory Highway seven miles from its junction with the Lincoln Highway and has the benefit of excellent automobile communication with the metropolis of the state. Both the Denver and Rio Grande and the Union Pacific Railroads give daily train service to the camp and effectively solve the transportation problems of the mining companies."

Jan 1, 1925

By F. F. Frick, Frederick Laist

In a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced by the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent by which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of, the copper as Cu2Cl2 from chloride solutions; with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, when a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid and no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly well. The use of a method of the. third class is involved in many special

Jan 1, 1915

By Y. Jeannin, C. Mannerskantz, F. D. Richardson

Measurements have been made between 1040o and 1300°C of the equilibrium between chromium metal, chromic oxide, hydrogen, and water. The results are in closer agreement with those deduced from recent thermal data than with previous equilibrium values. They lead to the equation ?G°1300°-1600°k = -266,700 + 59.95T ± 300 cal for the formzation of a mole of Cr2O3 from chromium and oxygen. This same equilibrium has been studied with the chromium dissolved in solid iron, and in this way chromium activities in Fe + Cr alloys have been established. The measuremenis show that there are substantial positive deviations from ideality in the a, and b phases, and support the results obtained by Heymer and Kubaschewski against those of other investigators. There is considerable disagreement between existing data,1"4 which is referred to in the Discussion, concerning the equilibrium Cr2O3 + 3H2 = 2Cr + 3H2O [l] There is also substantial disagreement between the results obtained by various investigators5-' who have measured the activities of chromium in its alloys with iron by the Knudsen effusion vapor pressure method. In view of the importance in metallurgical processes of chromium and its oxide and of Fe-Cr alloys, an attempt has been made to study equilib- rium [I] both with pure chormium metal and with chromium alloyed with iron, at temperatures between 1040o and 1300oC. From the work with the alloys it is possible to derive the chromium activities from the relationship

Jan 1, 1963

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,' and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,' and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By E. T. Turkdogan

The activities of SiO2, FeO, and Fe2O3 are calculated from previous experimental data on the activity of oxygen in Fe-Si-O melts at 1550°C. Using the oxide-activity data, the free energy of formation of fayalite from its oxides is evaluated for 1550°C. A number of investigators1-4 contributed to the study of the state of oxidation of iron in SiO,-FeO-Fe,O3 melts and the phase equilibria in the system Fe-Si-O. In a more detailed study, Schuhmann and Ensio5 and Michal and Schuhmann% easured the state of equilibrium in the SiO,-FeO-Fe,O3 melts saturated with y-iron or silica or both under low-oxygen potentials and within the temperature range 1250" to 1350°C. Similar measurements were also made by Turkdogan and Bills7,' over wide ranges of composition and oxygen potentials at 1550"C. Using the experimental data on the oxygen activities in the ternary system, Schuhmann' calculated the activities of silica and ferrous oxide in Si0,-FeO-Fe2O3 melts for 1350°C. Adequate knowledge on the activities of the constituent oxides of melts is essential in the study of reaction-equilibria and reaction-kinetics in oxide-melts. With this in view, the activities of oxides in SiO2-FeO-Fe2O3 melts at 1550°C are computed using the experimental data of Turkdogan and Bills7'8 on the oxygen activities in these melts.

Jan 1, 1962

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size.

Jan 1, 1950

By N. Mungan

Laboratory imbibition and displacement experiments were performed using crude oil and cores drilled with water and preserved under anaerobic conditions. The purpose of these tests was to determine reservoir rock wettability and to find out if more oil could be recovered by use of NaOH solution than by conventional waterflooding. The preserved cores were found to be oil-wet. Contrary to work in the literature, these cores changed to water-wet upon contact with air. After exposure to air for a week, the cores yielded more oil by waterflooding than when preserved under exclusion of air. At reservoir temperature of 160F, flooding the preserved cores with 0.5N NaOH solution recovered more oil than an ordinary wa-terflood, and additional oil when following a waterflood. When the caustic solution was used from the beginning, all the extra oil was obtained before breakthrough; when the caustic followed a conventional waterflood, the extra oil was produced in the form of an oil bank ahead of the injected caustic. The increase in oil recovery resulted from wettability reversal. Also, use of caustic reduced the volume of injection required to flood out the cores. At room temperature, however, the caustic solution did not reverse the wettability and gave no additional oil recovery. Cores which had become water-wet by air exposure or caustic flooding were restored to their original oil-wet state when saturated with crude oil and allowed to equcilibrate at reservoir temperature for two weeks. Therefore, in the absence of preserved cores, it may be possible to restore weathered cores to their original wettability for use in laboratory floods. INTRODUCTION Waterflooding has been in use since 1865, and is by far the simplest of secondary recovery methods. Unfortunately, most waterfloods are inefficient in recovering oil, often leaving half or more of the original oil in place un-recovered. The low oil recovery generally results from low sweep efficiency and low displacement efficiency. Consequently, to increase oil recovery by waterflooding, sweep and displacement efficiencies should be improved. Sweep efficiency is primarily affected by reservoir heterogeneities and mobility ratio, while displacement efficiency is affected by the capillary forces between fluids and rock surfaces. For petroleum reservoirs, the capillary forces are expressed in terms of interfacial tension and wettability. If oil recovery is to be improved significantly in water- flooding, the capillary forces holding the oil in the raervoir porous matrix must be reduced or eliminated. One way to reduce capillary forces is to inject commercial surfactants ahead of the injection water into the reservoir. Laboratory tests of this method have shown no promise of an economical process yet, and no increase in oil recovery was obtained in the field trials which have been reported. Work is continuing in many companies to find surface-active agents which, in workable concentrations, can yield substantial added oil recovery. Another way to change capillary forces operating in petroleum reservoirs is by changing the pH of the injected water. Wagner et al.' showed that change in the pH sometimes activates the surface-active materials natural to some crudes and brings about gross wettability change. Since pH alteration can be obtained with cheap chemicals, such as hydrochloric acid or sodium hydroxide, the process shows promise of being economical in a field application. Pan American Oil Corp. reported oil recovery by use of caustic solution from a flooded-out reservoir.' Their test, conducted at a small additional cost, yielded results which were so sufficiently favorable and encouraging that the wettability reversal flood was expanded to portions of the field not previously flooded.13 It is important to bear in mind that changes in the pH of the water not only can reverse wettability but also can lower the interfacial tension between water and crude oil. Reisberg and Doscher4 have studied the pH dependency of the interfacial tension of Venture crude using sodium hydroxide solutions of various concentrations. Their data show that the interfacial tension was lowered from 23.0 to 0.02 dynes/cm by increasing the NaOH concentration from 0.005 to 0.5 per cent by weight. Thus, the use of NaOH may lead to additional oil recovery due to both wettability reversal and lowering of interfacial tension. Whether alteration of pH results in wettability reversal from oil-wet to water-wet and increases oil recovery depends on wetting properties of the reservoir rock and the crude. This necessitates delicate laboratory experiments, with suitable core and fluid samples from a field. Although many investigators have studied wettability reversal floods in the laboratory,1,2,5,6 these studies have been carried out with synthetic porous media, refined laboratory fluids and surface-active chemicals to simulate the process. The study presented in this paper is the first time that wettability reversal by pH alteration has been accomolished in laboratory core floods using carefully preserved natural cores, live crude and with experiments performed at reservoir pressure and temperature.

Jan 1, 1967

By R. D. Daniels, T. G. Oakwood

A study was made of the effects of small quantities of hydrogen on the mechanical properties of colum-bium. Tensile specimens, hydrogenated to concentrations of 20 to 200 ppm, were tested at temperatures of 300°, 191°, and 77°K. Although hydrogen was found to have little effect on the strength of columbium, the ductility of Cb-H alloys was found to be quite sensitive to both hydrogen concentration and temperature. At 300°K, an abrupt loss in ductility occurred at a critical hydrogen concentration, although some ductility was observed beyond the tolerance limit. A similar result was found at a lower hydrogen concentration at 191°K. At 77°K, however, a more gradual loss in ductility with increasing hydrogen concentration was observed. Hydrogenated columbium was thus observed to undergo a ductile-brittle-ductile transition. Metallographic examination of fractured specimens revealed extensive porosity at both 77° and300°K which was a distinct function of hydrogen content. At 191°K, although some secondary cracking was noted, the amount of observed porosity was minimal. These observations are interpreted in terms of hydrogen solubility and mobility as a function of temperature and in the role of hydrogen in promoting growth of microcracks. lHE effect of hydrogen on the mechanical properties of the refractory metals is not, at present, completely understood. A number of studies have shown these materials to be susceptible to hydrogen embrittlement. Roberts and Rogers1 have found that vanadium can be embrittled by hydrogen. It was further demonstrated that fracture undergoes a ductile-brittle-ductile transition as the temperature is lowered from 150° to -196°C; i.e., there is a ductility minimum observed at a certain temperature. The ductility is increased by either raising or lowering the temperature from this point. A more complete study by Eustice and Carlson2 on vanadium containing 10 to 800 ppm placed the ductility minimum at about -100°C with variations reportedly due to hydrogen content and strain rate. Ductility minima have also been found at certain temperatures for tantalum containing 7 ppm H3 and 140 ppm H.4 At hydrogen concentrations above 270 ppm, however, the ductility return at low temperatures was considerably reduced.4 In the case of columbium, some disagreement exists in the literature. Eustice and Carlson,5 Wilcox et al.,6 and Imgram et al.4 failed to find a ductility minimum although a composition-dependent ductile-brittle transition was observed. Hydrogen concentrations in these investigations were 20 ppm,5 1 to 30 ppm,6 and 200 to 390 ppm.4 However, Wood and Daniels7 observed a rather pronounced ductility minimum at hydrogen contents ranging from 19 to 252 ppm. Those theories of hydrogen embrittlement involving the precipitation of diatomic hydrogen which have been applies to ferrous metals8-12 do not seem to be applicable to the case of columbium and other exothermic occluders. Such theories propose that extensive crack formation and propagation occurs by the precipitation and expansion of diatomic hydrogen at internal voids and microcracks. However, photomicrographs of hydrogenated columbium do not show any evidence of damage introduced by the sorption and precipitation of diatomic hydrogen; rather, at high hydrogen concentrations, a hydrogen-rich second phase is precipitated.13'14 In addition, a number of these theories require the development of high hydrogen pressures at voids in the structure.8'10'12 This does not appear to be feasible in the concentration ranges discussed in the aforementioned paragraphs. The possible interaction of atomic hydrogen with microcracks resulting from dislocation pile-ups15,16 remains in doubt since pile-ups have not been observed in bcc metals17 including columbium.18 Wood and Daniels7 have put forth the possibility that a hydride precipitation could be responsible for crack nucleation in columbium. Work by Longson19 has shown that hydrogen embrittlement of columbium parallels the bulk solubility limit; i.e., as the solubility increases, for instance with temperature, the amount of hydrogen necessary to cause embrittlement also increases. Although a hydride precipitation appears attractive as a means of nucleating microcracks in columbium, what require more intensive study are the low-temperature anomalies which have been observed, i.e., the ductile-brittle-d'ictile transition characteristics. Also, the hydrogen concentrations where embrittlement occurs are often below the bulk solubility limits determined by Albrecht et al.13,14 and Walter and Chandler.20 This work is an attempt to determine more definitively the effects of concentration and temperature on the mechanical properties of dilute Cb-H alloys. EXPERIMENTAL PROCEDURE Ultrahigh-purity columbium rods, obtained from the Wah Chang Corp., were cold-reduced by rotary swaging. A chemical analysis is given in Table I. The material was cut into cylindrical blanks 1.50 ±0.005 in. long. Individual specimens were either given a stress relief anneal at 750°C or recrystal-lized at 1200°C. Resulting microstructures were either a "bamboo" structure characteristic of a wrought material or a recrystallized structure with a grain diameter of approximately 100 n. All heat treatments were carried out in a vacuum of 10-5 Torr or less.

Jan 1, 1969

By C. W. Kovach, A. Moskowitz

Studies were undertaken to investigate the effects of manganese content on the machinability and other Properties of a free machining martensitic stainless steel (AISI Type 416). Machinability was found to be significantly improved in steels of high manganese content, and a direct relationship was obtained between machinability and steel Mn:S ratio. As the manganese content of the steel increases, the sulfide Phase present changes from CrS to (FeMn)Cr2S4 to (MnFeCr)S, and finally to MnS. The average sulfide inclusion hardness decreases through the same range of increasing manganese content. The mechanism for machinability improvement is discussed in terms of a soft ductile sulfide affecting deformation in the secondary shear zone. Type 416 containing relatively high manganese for improved machinability shows good general properties. The effects of increasing manganese content on mechanical properties, cold formability, and corrosion resistance are described. THE addition of sulfur is commonly used to improve the machinability of stainless steels. However, little attention has been paid in the past to the composition and characteristics of the sulfur-containing phase or phases present in these resulfurized steels. Recent information on the properties of sulfide phases, and their role in metal cutting, suggests that variations in these phases could have critical effects on machin-ability, as well as important effects on formability and other properties such as corrosion resistance. Manganese, chromium, and iron are strong sulfide forming elements present in stainless steels! of these, manganese has the greatest sulfide forming tendency and iron the least.1"1 The manganese content of resul-furized 13 pct Cr steels, often about 0.5 pct, can be insufficient or only barely sufficient to combine with the sulfur that is present; thus, the precise level of manganese can strongly influence the nature of the sulfide phase. Sulfide phases which may be present in stainless steels have been reported to include CrS, a spinel-type sulfide, chromium-rich manganese sul-fide, and manganese Sulfide.5,6 Detailed phase relationships for the Fel3Cr-Mn-S system have been reported by the present investigators,7 and a portion of this work will be referred to subsequently in this paper. Recent work by Kiessling6 and Chao et a1.8 has shown that sulfide phases can display wide variations in hardness, and may undergo considerable plastic deformation under isostatic loading.9-12 Early theories of metal cutting attributed the influence of sulfur to a lubricating effect. It is now apparent that the influence of the nonmetallic inclusions and their properties on crack initiation, deformation in the shear zones, and boundary films must also be considered in relation to the machining process. This paper presents the results of studies conducted to relate machinability to the various sulfide phases which occur in stainless steels. This work has led to the development of alloys with improved machinability, and has generated information on the effects of inclusions on metal cutting processes. Effects of sulfide inclusions and steel composition on other important metallurgical properties are also discussed. MATERIALS For drill machinability and inclusion studies, 10 lb laboratory heats were melted in an air induction furnace. These heats were made with sulfur contents be tween 0.10 and 0.50 pct and manganese contents be tween 0.05 and 3.0 pct. Residual elements were added to the heats in amounts typical for commercial steels. The typical compositional range covered by the heats is shown below: C Mn P S Si Ni Cr Mo Cu N 0.10 0.05 0.007 (M0 0.40 0.40 13.0 0.20 0.10 0.03 3.0 0750 The laboratory ingots were forged in the temperature range of 1800" to 2100°F to 3/4-in. sq bars, and all bars tempered to a hardness aim of 200 Bhn prior to testing. Because of differences in composition and tempering response, the tempered bars showed some variation in hardness (175 to 275 Bhn) as well as variations in delta ferrite content (0 to 50 pct). Composition, hardness, and delta ferrite content were considered in the analysis of the machinability data. Additional tests involving tool-life evaluation and determination of other properties were conducted on materials from commercially melted and processed 15-ton electric furnace heats. TESTS AND PROCEDURES Machinability of the laboratory heats was evaluated in a drill test. In this test, 1/4-in. diam holes, 0.4 in. deep, were drilled alternately in a test bar and in a standard bar for a total of four holes in each. This sequence was repeated three times using a freshly sharpened drill each time. The average time required to drill a hole in the test bar was compared to that for the standard bar. A drill machinability rating was assigned to the test bar relative to a rating of 100

Jan 1, 1970

GWILLIAM H. CLAMER (Philadelphia, Pa.).-About 16,000 tons of tin is used annually in the production of white metals. The real reason for using the so-called genuine babbitt, which is a high-tin base babbitt, perhaps in the majority of cases, is that tin has always been. a high-priced metal and people naturally believe that what they pay a high price for must be good. Mr. Jones has shown that the common metal, lead, is a superior base for most purposes for Which babbitt metal is used. The addition of lead is often looked upon as adulterant to genuine babbitt, and specifications for this reason rigidly restrict the lead content. A sub-committee of the Society for Testing Materials, at the meeting in June, presented tentative specifications on babbitt metal, in which were included twelve formulas, containing from zero to: 20, per cent. of tin, and several containing from 65 and 92 per cent. Babbitts. containing

Jan 1, 1919

DeLamar, the largest silver mine in the United States outside the Coeur d’Alene District in Idaho, came into production in April 1977. It is a joint venture of Earth Resources Company and Canadian Superior Oil Co., with Earth Resources being the operator. The property is a consolidation of several old operations dating back to the 1800s; the better known of these are the DeLamar and Sommer-camp mines. DeLamar is situated in southwestern Idaho near the Oregon border in the Owyhee Mountains, 88 km (55 miles) southwest of Boise, Idaho. Heavy snowfalls and very low temperatures are common in the wintertime. Planned production was 77,500 kg (2.5, million oz) of silver and 5 13 kg (16,500 oz) of gold per year. Expected life at a milling rate of 1,540 mtpd (1,700 stpd) was 20 years, with an ore grade of 144 g Ag and 1.58 g Au per mt (4.2 oz Ag and 0.046 oz Au per st). Present production is at the rate of 1,900 mtpd (2,100 .stpd). The total cost to bring the mine into production was reported to be approximately $22 million, and the mill was reported to have cost about $10,000 per daily ton of design capacity. At DeLamar, naurnanite (Ag2Se) is the principal silver .mineral occurring with acanthite (Ag2S) disseminated through quartz veins and a silicified rhyolitic ash-flow tuff of Miocene age. The mineralization is relatively iron and manganese free and is readily amenable to cyanidation giving recoveries of 85% silver and 92% gold, which occurs free. When the plant was started, considerable difficulties were encountered in handling the wet sticky ore because of the high clay content. Following primary crushing, the ore is stockpiled. Due to the sticky nature of the ore, the vibrating feeders initially installed under the stockpile were replaced by a reclaim hopper and an apron feeder which was fed 24 hours a day by a front-end loader. The minus 200 mm (8 in.) ore is fed to a 5.5 m by 2.75 m (18 ft by 9 ft) autogenous mill followed by a 2.75 m by 4.57 m (9 ft by 15 ft) ball mill and cyclones. The mills are equipped with 750 kw and 520 kw (1,000 hp and 700 hp) motors. Both mills discharge to the same cyclone feed sump and a portion of the cyclone underflow is returned to the autogenous mill. Cyclone overflow, which is 20% plus 74 microns (200 mesh), is leached in four agitators in series for 72 hours (45 hours at the 2,100

Jan 1, 1981

By E. R. Brownscombe, Francis Collins

The pressure distribution in a reservoir producing an incompressible fluid by radial flow in a horizontal structure is a simple logarithmic function' used daily by reservoir engineers. The assumption of an incompressible liquid is equivalent to assuming that pressure is maintained constant at the well radius and at some external "radius of drainage," or, in other words, that the entire flow into the well passes across the external radius. In most cases a well is surrounded by other wells draining adjoining areas so that the "radius of drainage" is not a line of constant pressure with flow equal to the flow into the well but rather a contour of zero pressure gradient across which no flow occurs, production being due to the expansion of the liquid within the area. The radial flow steady state pressure distribution for this case does not seem to be extensively used despite the fact that the mathematical analysis has been given in detail' and the results are simple and generally applicable. 'The object of this discussion is to develop this result from a physical rather than a mathematical viewpoint, thereby aiding intuition in judging circumstances to which it may be applicable. If the production rate at a well in an unsaturated reservoir is maintained constant while no flow occurs across the outer radius a steady state will soon be reached in which the flow rate or pressure gradient is constant with time at all points in the reservoir. To preserve such a condition it is necessary that the pressure decline at the same rate at all points in the reservoir, that is, the curves of pressure versus radial distance at successive times are all parallel. Then each unit volume of oil is expanding at the same rate and contributing an equal share to the production. The rate of flow q across any circle r is thus proportional to the volume of the reservoir between r and the external radius re, or q = qw (I-r2/r2e) ......(1) where q, is the production from the well and it is assumed that rw is very small compared with re. This equation can be combined with the differential form of Darcy's law for radial flow, 2phkr dp q =—— ........(2) aµß dr ( where q is not a constant as in the incompressible flow case but is a function of r given by Equation (1). If Equation (1) is substituted in Equation (2) the variables p and r can be separated and the result integrated to obtain the pressure distribution p = pw +--------In------------- 2pkh[ rw 2re2] ......(3) This equation differs from the incompressible case only in the addition of the term proportional to the square of the radius

Jan 1, 1950

Here are the details . . . . . of how a $2.5 million research gamble, now backed by five years of intensive development in cooperation with the Chemical Construction Corp. resulted in a hydrometollurgical process that yields pure metal powders from sulphide concentrate - a process that offers potential savings of $2.5 million a year.

Jan 6, 1953

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size.

Jan 6, 1950

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples. Gaudin,1,2 the first to apply a nuclear reaction in detecting beryllium minerals, developed a method that irradiates the sample with gamma rays, which react with beryllium nuclei to produce neutrons. The neutrons are then measured with standard equipment. The cross section for this reaction is about 1 millibarn. The cross section is a measure of the probability that a reaction will take place, for example, between a beryllium nucleus and an incident gamma ray or alpha particles.3-5 At 1-millibarn cross section for the reaction, satisfactory performance required a source strength of the order of 1 curie (3.7 x 10"' disintegrations per sec, where each disintegration releases one or more gamma rays). The reactions will not take place if the gamma radiation is below a minimum energy, in this case 1.63 mev. The size of the source and the energy of the radiation made heavy shielding necessary for these experiments, both to reduce the background count of the neutron counter and to safeguard personnel. The original discovery of the neutron by Chad-wick in 1932 resulted from experiments with another nuclear reaction, induced by bombarding beryllium with alpha particles in which the products are carbon-12 and neutrons. The equation for this reaction is as follows:' " ,Be" + ,He'? 6C12 + 8,n' [1] re-particle neutron In the above nuclear equation (Eq. 1), the sub- script number indicates the number of protons in the nucleus (the atomic number) and the superscript the total number of neutrons and protons (approximately the atomic mass). For the alpha-neutron reaction the cross section is about 250 milli-barns, or 250 times that of the gamma-neutron reaction used by Gaudin. The positively charged alpha particle is repelled by the positive charge of the beryllium nucleus; it must, therefore, have a certain minimum energy in order to approach close enough to the beryllium nucleus to react. For reaction with the beryllium nucleus, the lower limit of the alpha-particle energy is 3.7 mev. The alpha-neutron reaction, with polonium-210 as an alpha source, was selected for the present experiments. Alpha particles are emitted by polonium-210 at 5.30 mev, which is adequate for the reaction with beryllium. Furthermore, this isotope of polonium emits alpha particles with negligible associated gamma radiation, thus eliminating the necessity of shielding. The half-life of polonium-210 is 138 days. Inasmuch as alpha particles carry a possible charge and are large compared with most nuclear particles, their energy is rapidly dissipated in passing through matter. Their range in standard air is 3.66 cm,3 and they penetrate only a few tens of microns into a mineral sample. The short range in air can be minimized by preparation of a flat sample surface that can be brought very close to the alpha source during analysis. On the other hand, short range of alpha particles in air lessens the radiological health hazard and makes it possible to use this method without shielding. It must be emphasized, however, that the alpha emitters are potentially very dangerous if they enter the human body. Polonium must be handled with extreme caution. The literature has reported experiments on the yield of neutrons from reaction of alpha particles with beryllium nuclei. Feld" reports that in intimate mixtures of polonium and beryllium, 3 x 106 eutrons per sec are produced per curie of polonium. Elsewhere in the same reference it is stated that a sandwich-type source yields about one third as many neutrons as an intimate mixture. A table of neutron yields for full energy polonium alpha-particles on thick targets as reported by Anderson7 is the basis of Table I. From Table I it can be deduced that the elements most likely to interfere, i.e., those that also produce neutrons when bombarded by alpha particles, are boron and fluorine. These data also show that it will probably not be possible to determine very small quantities of beryllium in rocks because of the masking effects of the major elements, sodium, magnesium, and aluminum. The neutrons emitted in the alpha reaction are detected by another nuclear reaction. Either of the

Jan 1, 1960