Search Documents

By J. E. Burke, Y. G. Shiau

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By Robert Rhea Goodrich

This research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward I?. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. Petrogeaphic DescRiption Texture: variable. Fine to medium mixed aggregate. Original Structure: Obscurc. Secondary structure: Fractured; healed. Mineralogy (Minerds are grouped for interpretation purposes and are arranged, in each group in approximate order of abundance)

Jan 1, 1916

By R. W. Ph. D. Raymond, Anton Filers, O. H. Hahn

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty furnaces exist in Utah, about as many in Nevada, five in Montana, and four in Cerro Gordo, Inyo County, California, it is obvious that a business so extended deserves attention. Wide apart as these different works are located, they have nevertheless to deal in nearly every case with the same or very similar circumstances and conditions, so that, with very few exceptions, virtually the same system of smelting is followed in all these establishments. This is the so-called method of reduction and precipitation in blast-furnaces. As the principal reasons for the employment of a blast-furnace process are to be considered : the low percentage of lead in the ores, the high price of the only available fuel, charcoal, and the exorbitant rates demanded for labor. The reasons why the reduction and precipitation process is preferred to a roasting, reduction, and precipitation process are the high prices of labor and materials, and the preponderance of oxidized ores over sulphurets, though in some cases the latter are quite abundant. The weight of these reasons will be better understood when the character of the ores to be treated and the object of the smelting are more minutely stated. The ores are in nearly all cases a preponderating mass of oxidized lead ores, such as cerussite, anglesite, and leadhillite, in which nests and nodules of undecomposed galena occur. Associated with these are : in Eureka, Nevada, arseniate of iron and arsenical pyrites, hydrated oxide of iron, quartz, and calcareous clay ; in Little Cottonwood Canyon and American Fork, Utah, iron oxide, and in some cases a combination of antimony, the nature of which I have not ascertained; also dolomite and quartz in widely varying proportions; in Bingham Canyon, Utah, only quartz and comparatively little oxide of iron, or iron sulphurets; in Cerro Gordo, California, oxide of iron, iron pyrites, antimonial compounds, copper ores, and, as gangue, carbonate of lime and quartz. In Argenta, Montana, occur, besides the above-named lead ores, pyromorphite, and molybdate of lead. The preponderating gangue of the Argenta ores is quartz, and there is here a larger proportion of galena than elsewhere in the West. In most of the localities named, the lead ores themselves contain sufficient silver to render its separation from the ore the main object of the smelting; but in some of the districts, and especially in Montana, the lead ores serve only to furnish the extracting agent for the silver of true quartzose silver ores, which at the same time contain a sufficient percentage of lead to make amalgamation impracticable. They are therefore beneficiated by smelting, although the lead itself has no market value.

Jan 1, 1873

By C. E. Jr. Reistle

ALL crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms.

Jan 1, 1927

For the seventh consecutive year, the value of nonfuel mineral raw ma¬terials produced in the US set a new record, reaching almost $20 billion-up 12.7% from the previous year, according to the US Bureau of Mines. The Bureau reported that this mineral production was the basis for about $200 billion worth of processed materials of mineral origin.

Jan 5, 1979

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

By Lewis Reeve

As part of a program of investigation of the properties of electric arc welds carried out in the laboratories of the A. 0. Smith Corporation, considerable work has been done on the determination of the oxygen, nitrogen and hydrogen content of different types of weld metal, employing for this purpose the so-called "vacuum fusion method." It is the purpose of this paper to describe certain improvements that have been introduced in this method of determining the gas content of metals, with particular references to the steel specimens examined in this investigation. The method and apparatus used at the beginning of the investigation were essentially those of the Bureau of Standards as described by Vacher and Jordan.' Later a number of changes were introduced which resulted in more rapid evacuation of the graphite crucibles employed and which enabled larger volumes of gas to be dealt with than could be handled conveniently in the Bureau of Standards equipment. In addition, the analyzing of the gases evolved from a melt in the same apparatus as collected was abandoned in favor of analysis outside the equipment using standard methods of gas analysis. The time required for gas analysis in the apparatus itself, as described by the Bureau of Standards, was found to be considerable, and during this time the rest of the equipment was tied up, preventing its use for the analysis of further steel samples. As a result of the modifications introduced, the time required for the analysis of a steel sample for gas content was reduced from about 8 hours to less than 3 hours. Subsequently, the whole procedure of melting the sample and collecting the gases evolved was modified so as to enable a distinction to be drawn between the easily reducible oxides such as iron oxide and the more stable oxides such as silica and alumina. At the same time evidence was obtained indicating the probable existence in the steels of other nitrides than those of iron alone and making possible their quantitative etermination.

Jan 1, 1934

By H. Vincent Wallace

ALTHOUGH it is universally accepted that free oxygen is A necessary in a cyanide solution for the dissolution of gold and silver-in accordance with Elsner's equation that 2Au + 4KCN + 0 + H20 = 2KAu (CN), + 2KOH- little has been written and insufficient attention paid to the drop in extraction due apparently to loss of dissolved oxygen in mill solutions. Aeration or oxygenation of cyanide solutions has been more or less successfully accomplished by various types of agitators such as the Dorr (with or without air lifts), Pachuca tanks and more recently "Turbo-mixers" and Denver "Super- agitators"; also by the introduction of chemical oxidizing agents such as Solozone (Na,O,) . At the Wright-Hargreaves and other mines in the Kirkland Lake camp, the introduction of this reagent at the rate of about 1.25 oz. per ton of ore applied to the feed of the ball mills has certainly been beneficial.

Jan 1, 1932

By Robert Mehl

IN examining the progress of metallurgical science, the critic must remember that most of our present knowledge of metals and alloys has been accumulated through the needs of industry and commerce rather than through the desire and efforts of a large body of scientists interested primarily in developing a science of metals. The progress of metallurgy, scientifically speaking, has been irregular, and little given to the exhaus-tive exploitation of important scientific fields. The experienced engineer now recognizes the need for the development of the basic science upon which his engineering rests. In addition to the increase in knowledge which results from the normal requirements of industry, a development of the basic science of the behavior of metals and alloys is as desirable in metallurgy as in any other branch of science and engineering. The continued growth of the science of metals-as of every other science-requires studious attention to the principles that underlie the behavior of matter, with the result that knowledge in the several fields of interest should continue to increase. Among the various subjects recognized as important in physical metallurgy few have a wider significance than that of diffusion in solid metals. The phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this, the process of diffu-sion is of first importance practically. The formation of alloys by the annealing of mixed powders, first practiced by Faraday and Stodart81 in 1820 and in more recent years investigated by Masing187,189 and others, has led to the development of special alloys like Carboloy, Vascoloy-Ramet, Genelite, Elcon68, and has recently been applied to the production of noble-metal alloys for electrical contacts"'.

Jan 1, 1936

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By Edwin S. Sperry

Metals differ widely in their behavior under the cuttingtool. Some, like iron or steel, require a slow speed and light feed, a tool shaped differently from that used for other metals,

Jan 1, 1898

By R. G. Brown

Tars paper will present a general description of the different mineral belts in the Butte City region (limited, however, to the copper and contiguous silver veins) such as may serve to give an intelligent idea of the distribution and characteristics of the deposits, forming thus a groundwork of information, which it is hoped will have value, when later writers enter into particularized detail.

Jan 1, 1895

By J. A. Herbst, A. L. Mular

Digital simulation is defined and simulation techniques are re- viewed. Typical methodology involves the selection of models, the adjustment of raw data, the selection of a fitting strategy, the assessment of model accuracy in a statistical sense, and the development of an executive simulation structure. Simulations serve as aids for process engineers in evaluating the feasibility of a proposed flowsheet and the effect of a modification to an existing flowsheet. In addition, simulation plays an important role in off-line optimization and in the evaluation of alternative circuit control strategies. Several examples are presented to illustrate these uses for simulation including applications in crushing circuits, grinding circuits, and flotation circuits. It is the opinion of the authors that, within the next decade, mineral processing plants will be studied routinely via digital simulation during the preliminary design stage. Simulation will constitute an important component of the design decision making process.

Jan 1, 1978

By W. A. Backofen, B. C. Wonsiewicz

The Plasticity transition in magnesium was studied by plane-strain compression of single crystals and polycrystalline material at temperatures from about 20" to 307°C. Reduction of single crystals along the c axis was accommodated by twinning on {1011) and retwinning on (10 12}, followed by basal shear in the doubly twinned volume. Deformation in that mode can result in sufficient independent shears for arbitrary shape change. Fracture in c axis compression, below about 100°C, has been related to excessive shear caused by unloading from the stress for {1011} twinning (-50 ksi at 20°C) to that for slip within the twin (-3 ksi); ductility follows from heating because the stress difference is lowered and the twin volume, in which elastic strain energy is dissipated on unloading, is increased. The stress for (1011) twinning is strongly temperature-dependent but not given by a critical resolved shear stress law. The latter is attributed to the influence of stress concentration from prior intersecting shear on nonbasal planes, the former to the temperature dependence of the preliminary slip. THE basic symmetry of hcp crystals has the effect of limiting the number of independent slip systems and making twinning an important deformation mechanism. The general result in wrought polycrystalline aggregates is a more or less sharply developed texture (or preferred orientation) which underlies a strong anisotropy in mechanical behavior. Knowing how the one influences the other is essential background for the use of such materials. Magnesium was of interest in this work because of the unexplained plasticity transition that it undergoes somewhere in the neighborhood of 200°c.''~ At lower temperatures plastic deformation before fracture in polycrystalline material is limited, while at higher temperatures extensive deformation is possible. The transition temperature commonly determines the lower limit of the range in which magnesium is worked. The limited ductility can be traced to a lack of independent crystallographic shears. A minimum of five are required for arbitrary shape change.' Around room temperature, however, slip on all known systems provides only four.' In each case, the slip direction is in the (0001) basal plane so that slip does not allow strain along the c axis. With increasing temperature, more slip occurs on the ( 1011) pyramidal plane and the ( 1010) prism plane but without change in direction.'?' Thus, that development alone cannot explain the transition temperature.

Jan 1, 1968

By Arthur Phillips, C. H. Mathewson

During the past year considerable work dealing with the mechanical properties and microstructure following the anneal under uniform condi-tions of certain types of commercial rolled brass has been done in this laboratory. Since these experiments were conducted with the active cooperation of the Bridgeport Brass Co., involving free use of its product, and have thus furnished information which is characteristic of some of its special mixtures, full publication of the numerical relationships and comparative results encountered does not seem justifiable. Some of the more general features of this work are, however, available and it is our present purpose to use the material in question, along with some results of special tests, in discussing the characteristics of recrystallization as related to the degree of hardening by strain and the ordinary annealing variables. We desire to make acknowledgment of the many courtesies extended by Mr. Charles Ferry, Metallurgist of the Bridgeport Brass Co., and the value of his cooperation, which has greatly stimulated the study of brass in this laboratory. A clear and systematic presentation of the principal relations between temperature and time of anneal, the changing physical properties and microstructure and the degree of previous reduction by cold-rolling, was first made, in the case of rolled brass and copper, by the French engineer, C. Grard,' in 1909, although much fragmentary information of this general character had appeared earlier and the main facts involved were undoubtedly known to many brass specialists through their own private research. From this work, it appears that in the cartridge mixture (67 per cent. copper, 33 per cent. zinc) the properties imparted by cold-working within the limits, 13 to 75 per cent, reduction of area by rolling Original Area — Final Area 0.13 to 0.75), are not affected by anneal- Original Area " ing for a 50-min. period at any temperature below 200°C. At or in the

Jan 1, 1916

By Kenneth Seaver

(San Francisco Meeting, September, 1915) INTRODUCTION IT is rather gratifying that in the field of the manufacture 'of refractories, in which, as a whole, foreign practice has surpassed us, the United States stands pre-eminent in the making of silica brick. In some instances European manufacturers have refused point-blank to credit the possibility of making to such specifications as are common with us, until the actual 'completed shapes were shipped for inspection. But both the manufacturer and consumer in foreign lands are now frankly learning from us, and benefiting by our advanced practice in this field, as is evidenced by the orders placed here and the efforts put forth abroad to come up to the standard of American-made material. In no metallurgical operation has the employment of silica brick spread with. such leaps and bounds as in the building of plants for the carbonization of coal, particularly in the byproduct coke oven. Today, in practically all types of oven, the structure above the floor level (except the facings) is of silica, while in the recuperative and in some regenerative types, its use is extended to that portion of the oven below the floor as well. By reason of the fact that there are a number of classes of refractories of higher silica content than the usual so-called fire-clay brick, there is sometimes a misunderstanding as to the class of material referred to as "silica" brick. We here refer only to a brick having a silica content of 94 per cent. or more and made usually from quartzite rock with a small percentage of lime as a binder. The term "silica" brick is sometimes rather loosely applied to brick front highly siliceous clays, or to a quartzite refractory of mingled fire-clay and quartz rock; but such products are not considered in this discussion.

Jan 9, 1915

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

By George B. Clark

THE " Munroe effect" of shaped explosive charges was discovered by Charles E. Munroe more than 50 years ago (in 1888), but it was not until World War II that it was put to any practical use. Both Allied and Axis armies used the principle effectively in bazooka projectiles, artillery projectiles and in fixed shaped charges. The first two were used primarily to combat tanks and other armor and the latter to assault pillboxes and other fixed concrete emplacements. Many engineers and others who saw the military application of the jet effect of shaped charges believed application would be possible in many industrial fields where blasting is used, such as mining and quarrying. Some work has already been done on the problem of making shaped charges applicable to mining operations. Experimentation conducted at the National Tunnel and Mines' was directed primarily along the lines of use of shaped charges for secondary blasting in connection with long-hole stoping methods. Experimentation initiated earlier and conducted by the author2 at the University of Utah on a more scientific basis was directed at revealing the basic principles of the functioning of shaped charges, as well as the feasibility of using them in mining operations after the principles of their operation had been clearly defined. It was found that: (I) a given design of charge required an optimum standoff to make it most effective, either in penetrating solid rock or steel (see Fig 3); (2) for a given design of charge there exists an optimum ratio of charge diameter to charge height above which the increase in effectiveness of the charge decreases rapidly (see Figs 4 and 5); (3) partial confinement has the effect of making charge performance much more consistent; (4) the higher power and higher velocity explosives tested are much more effective than relatively low-strength explosives; and (5) shaped charges may be adaptable to mining operations in secondary breakage and drilling blasting holes. Fig I is a diagrammatic sketch of the action of a shaped charge for two types of cavities, while Fig 2 shows the approximate manner in which the jets are believed to be formed when an explosive wave encounters the cavity, approaching it from the top. The experimentation already completed has laid the foundation for further research in the study of shaped charges. Standoff effects, effect of the strength of explosives and other features have been fairly well established. Such elements in the design of shaped charges as (I) geometry of cavity liners, (2) relative horizontal dimensions of explosive column, (3) effect of

Jan 1, 1947