Search Documents

By J. H. Palm

Experiments have shown12 that the formula -S = St - (St - Se')e ne [1] expresses very well the relation between the true stress S and the true form monotonic deformation of plastic metals in single tension and compression (Fig 1). St (asymptotic or final stress), Se' (threshold stress) and ne (characteristic or specific strain) are constants, the significance of which immediately follows from Fig 1. Only at the initial stages of deformation the experimental curve runs below the theoretical curve. This may be due, at least partly, to the uneven stress distribution caused by the anisotropy of the crystals. It is now obvious that a similar formula H = Ht- (Ht- He)e ne' [2] might be valid for the relation between the hardness and the strain. The hardness can be only a function of the strain and must therefore be independent on the hydrostatic tension present in the neck during straining. Hence, if Eq 2 is correct it will also represent the relation between hardness and strain in the middle section of the neck, the strain of which is generally assumed to be almost or fully homogeneous. For aluminum, copper, and several copper alloys it is indeed observed that Eq 2 agrees very well with the experimental Vickers hardness-strain relation from zero strain on up to the strain at fracture. Moreover nc' is, for several metals fairly equal to nc- Hence H = C1 + C2S [3] C1 and C2 are constants during uniform uniaxial tension. Eq 3 was also obtained for copper by Voce.3 According to Hencky's theory4 the ratio of the Brinell or Vickers hardness and the yieldstress (expressed in kg per mm2) of a non-strainhardening metal is approximately equal to 2.8. If Eq 1, 2 and 3 are correct the ratio Ht/S, must accordingly be the same for all plastic metals and be equal to 2.8. It is now experimentally established that this ratio varies between 2.7 and 3.1 with a mean value of 2.9. Taking into account that Ht and especially St can be obtained only by extrapolation from the range of rather low strains, the agreement with the theory is very satisfactory. References 1. J. H. Palm: Appl. Sci. Res. Al (1948) 198. 2. E. Voce: Jnl. Inst. of Met. (1948) 74, II, 537. 3. E. Voce: Metal Treatment (1948) 15, 53. 4. H. Hencky: Zlsch. f. angew. Math. and Mech. (1923) 3, 241.

Jan 1, 1950

By Charles R. Keyes

PAGE. I Introduction,........674 11. Occurrence............ 676 III. Geology of Death Valley BoRate-Region,....677 1. Surface.Relief ......677 2. Geologic Formations,....680 3. Geotectonics,..684 IV. FURnace Canyon Deposits..686 1. General Features..686 2. Geologic Structure..688 3. Ores.....690 4. Typical Section ...691 V. Lost Valley Deposits...693 VI. Mojave Desert Deposits..693 1. Distribution....693 2. Geologic Structure ........694 3. Ores............ 696 VII. Santa Clara Valley Deposits .699 1. Distribution....699 2. Geologic Structure..700 3. Ores.....700 VIII. Ventura County Deposits..701 IX. Geologic Occurrence of Borax .701 1. Original Sources...701 2. Solfataric Borax...702 3. Lacustrine Borax...703 4. Marsh Borax....703 5. Terranal Borax...704 X. Chemistry of Natural Borates.... 705 1. General Considerations.....705 2. Composition of Saline Waters...706 3. Solubility of Components....707 4. Time-Element in Water.Concentrations . 707 5. Effect of Temperature.....708 6. Effect of Pressure......709 XI. Occurrence of Other Commercial Salines,.... 709 I. Introduction. A complete transforrnation has taken place in the borax industry during the year 1908. A most remarkable factor in

Jan 1, 1910

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By Lombard Squires, W. K. Lewis, W. I. Thompson

Clays consist predominantly of hydrated silicates of alumina. The formula is frequently assumed to be A1203 . 2Si02 . 2H20,'and certain of I. North Carolina. Low plasticity. 11. Same as I, after washing. Low plasticity. III. Tennessee. Good plasticity. IV. Pennsylvania flint fireclay. Low plasticity. V. Laredo, Texas. Very plastic. CaO/Na2O corrected for GO2. VI. San Antonio, Texas. Fine grained, highly plastic. Moisture and CO2 were determined together at 18.8 per cent. VII. Selected crude bentonite, California. " Data from R. Ries: Clays. John Wiley & Sons, New York, 1927. them undoubtedly have substantially this composition, but in general the ratio of silica to alumina is considerably higher. However, they always contain water of chemical constitution, as shown by Table 1.

Jan 1, 1935

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By d&apos, C. McCoul, C. Antonio, R. Krohn

MOST of the commercial colored gold alloys for jewelry applications are based on the Au-Ag-Cu-Zn system. Although work has been done on the constitution of the Au-Ag-Cu system.'-4 there are no reports in the literature on the effects of zinc additions in these alloys. We have metallographically determined the a =al + a2 transformation temperatures in 91/2- and 131/2-karat alloys in which varying amounts of zinc have been substituted for copper and silver. Samples were cast in the form of 1/2-in. round bars

Jan 1, 1970

By S. H. Cathcart

Price, production and drilling operations exceeded any year since 1930. A top price for crude of $2.55 was maintained from May 1 to November 6 and increased activity about coincides with that period. The average crude price for the year was: Bradford, $2.46; Kane-Butler, $2.34; Southwest Pennsylvania, $2.13. Production for the year exceeded 15 million barrels, an increase of about 2 million barrels over 1933. That this increase was more than justified by market demand is indicated by a reduction of 892,000 bbl. in stocks for the year. Two classes of data appear on Table 1, which are differentiated by footnote references. Where possible the .figures were obtained from individuals and companies that, from long acquaintance and varied contacts, are most capable of supplying an estimate where an estimate is necessary. The remaining data represent a rather careful compilation from all available published records (see p. 378). Drilling operations and production as summarized by the Oil City Derrick are as shown on Table 2.

Jan 1, 1935

By H. Margolin, E. Ence

A. J. Goldak and J. Gordon Parr University of Alberta) —Margolin and Ence's paper reached us only a few days after we had submitted a paper on the structure of Ti2Cu to the AIME. Here, however, we only wish to point out an error in the paper (page 321): "Karlsson has reported the crystal structure of the first intermediate phase occurring in the Ti-rich portion of the Ti-Cu system to be face-centered tetragonal." Karlsson actually reported the structure of Ti3Cu (i.e., "the first intermediate phase") to be primitive tetragonal with four atoms per lattice point: Cu at 0, 0, 0; and Ti at 1/2, 1/2, 0; 0, 1/2, 1/2; and 1/2, 0, 1/2. Thus, Karlsson suggests a primitive lattice with an ordered arrangement of atoms located at corners and face-centers: Ence and Margolin suggest a random body-centered tetragonal structure—-with which our results agree. E. Ence and H. Margolin (azlt1zo.l-s' reply)— We do not agree that Karlsson has not reported the structure of Ti3Cu as face-centered tetragonal. The fact that Cu atoms are located at the corners and titanium at the face-centers does not indicate that the lattice is not face-centered. We are pleased that the discussers' results agree with our own.

Jan 1, 1962

By M. G. Benz, J. F. Elliott

A. J. Goldak and J. Gordon Parr (U)iuersity of Alberta) —Margolin and Ence's paper reached us only a few days after we had submitted a paper on the structure of Ti2Cu to the AIME. Here, however, we only wish to point out an error in the paper (page 321): "Karlsson has reported the crystal structure of the first intermediate phase occurring in the Ti-rich portion of the Ti-Cu system to be face-centered tetragonal." Karlsson actually reported the structure of Ti3Cu (i.e., "the first intermediate phase") to be primitive tetragonal with four atoms per lattice point: Cu at 0, 0, 0; and Ti at 1/2, 1/2, 0; 0, 1/2, 1/2; and 1/2, 0, 1/2. Thus, Karlsson suggests a primitive lattice with an ordered arrangement of atoms located at corners and face-centers: Ence and Margolin suggest a random body-centered tetragonal structure—-with which our results agree. E. Ence and H. Margolin (authors' reply)— We do not agree that Karlsson has not reported the structure of Ti3Cu as face-centered tetragonal. The fact that Cu atoms are located at the corners and titanium at the face-centers does not indicate that the lattice is not face-centered. We are pleased that the discussers' results agree with our own.

Jan 1, 1962

By W. L. Austin

At the Steptoe metallurgical plant, where ore of the Nevada Consolidated Copper Co. is beneficiated, a small copper-leaching annex has been in operation treating flue dust from roasting-furnace dust chambers, together with a siliceous oxidized ore. This leaching plant was designed to obviate smelting low-grade siliceous flue dust, which interfered with the operation of the reverberatories by forming a blanket on the charge. The major portion of the copper content of the flue dust accumulating in the upper chambers of the roaster flue, and at the stack, is water soluble, and also contains much free sulphuric acid and soluble sulphates. It was found that sufficient acid could be obtained by mixing this material with water to provide a lixiviant for leaching the siliceous copper ore mentioned. This was the sole source of the lixiviant used in the operation to be described. An analysis of the flue dust showed it to be composed as follows : Per Cent. Copper.............................................. 3.00 siO2................................................. 23.41 Fe................................................... 4.08 CaO + MgO......................................... 2.72 Al203................................................ 0.07 Free H2S04........................................... 19.94 SO3 combined as sulphate.............................. 25.10 H2O combined with the sulphates....................... 10.67 0................................................... 2.50 Total................................... 97.49 Copper soluble in dilute H2SO4.......................... 2.56 The oxidized ore, locally known as carbonate, has the following composition:

Jan 1, 1915

By Paul M. Tyler

MINOR industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz (Iceland spar, tourmaline, fluorite, selenite, mica), and nonfuel gases (air, helium, carbon dioxide). ALUM MINERALS The alums comprise a series of double sulphates (or selenates) isomorphous with potash alum, which, according to a ruling of the Pennsylvania courts, is the only product commercially described simply as "alum." Common alum occurs in nature as kalinite (K2SO4- A12 (SO4) 324H2O). The mineral mendozite (Na2S04) 3.A12 (SO4)3- 24H2O) is soda alum; tschennigite (NH4)2SO4.Al2 (SO4)3.24H2O) is ammonium alum; and there are about a dozen other native alums and related double sulphates. Alunite (alumstone or alum rock) has the formula Al2(SO4) 3.K2S04.4A1 (OH)3 and alunogen, Al2(So4) 3.18H20. Saline residues, found wherever natural water is evaporated, may contain sulphate of alumina, which for most uses is the essential ingredient of alum. Mineral wells and springs that emerge from beds of pyritiferous shale are typically astringent and at times form local deposits of alum, generally as incrustations. Acid waters acting upon aluminous rocks may form sulphates of alumina. The alums of commerce, as well as aluminum sulphate (concentrated alum), are produced principally by treating bauxite with acid, but they have been made also on a substantial scale from clay, cryolite, pyritic slates, schists, lignites, alunite, and leucite. Alum shale-chiefly clay, pyrite, and (usually) carbonaceous matter-was extensively used in England as a source of alum for more than two centuries. In France, pyritic lignites mixed with sand and clay were burned in heaps to red ash, the leach Liquors from which, after treatment with ammonia, yielded alum and copperas. Processes have been developed for making alum or aluminum sulphate from such diverse materials as feldspar, aluminous phosphate minerals, greensand, and mixtures of mica and

Jan 1, 1949

By Michel Elle, John Chipman

The equilibrium of gaseous H20-H2 mixtures with liquid iron-columbium alloys in the range 0.2 to 2.4 pct Cb shows that the activity coefficient of oxygen is strongly diminished by Cb. The oxide in equilibvium with the melt is identified as CbO2. The equi-librium constant at 1600 deg C is [%Cb][fo. % 0]2 = 2.9 x 10-4 where log fo= —0.14 [%Cb]. The deoxidizing power is comparable to that of vanadium, COLUMBIUM (niobium) is finding increasing use as an alloying element in steel. It forms several stable oxides and is removed from the steel bath by oxidizing slags. The specific oxide formed in steel-making is not known although Sazanov snd Shvarts-man,' in their study of its partition between slag and metal, have assumed this to be Cb2O5 It is the purpose of this study to determine its deoxidation equilibrium at 1600°c, the nature of the oxide formed and the interaction between columbium and oxygen in the melt. The investigation was based on the reaction H2 + O=H2O; Kl=ph2o/(pH2[%O]) [1] in which 0 signifies oxygen dissolved in the liquid Fe-Cb alloy. The method and equipment of recent studies2,3 were utilized. In brief, the molten alloy, contained in a small crucible, is held in a controlled mixture of steam, hydrogen, and argon until equilibrium is reached. It is then cooled quickly in a stream of helium and analyzed for columbium and oxygen, the latter by vacuum fusion.4 The solubility of the oxide in liquid iron is determined by visual observation of scum formation on the surface of the melt. Crucibles of MgO proved unsatisfactory because of partial reduction at the metal interface. Pure A12O3 crucibles were heavily blackened by the melt and could not be used at high concentrations of columbium. Silica crucibles were more satisfactory but these introduced some silicon into the melt thus necessitating an uncertain but small correction for its effect on the activities of the other solutes. In silica it was possible to observe the scum formation when the melt became saturated and there was no apparent reaction between scum and crucible. The procedure for saturated melts was as follows. The alloy charge composed of electrolytic iron and columbium grain was melted and held at constant temperature. The gas ratio H2O:H2 was progressively increased by raising the saturator temperature until a point was reached at which a bright film appeared on the surface and covered it completely. This film could be dissolved by raising the temperature of the melt and it reappeared when the temperature was lowered. Under a partial film covering, utilizing bare areas for temperature measurement, the melt was brought to equilibrium with the atmosphere by holding at temperature for about 1 hr as suggested by Dastur.5 INTERACTION IN THE MELT Several experiments were made without columbium to establish a base in silica crucibles. The results are shown in Table I. Except for one run, they agreed well with Floridis1 comparable results in other crucibles. The value of log K1 is taken from Table I as 0.58. This is slightly larger than Floridis' result, probably because of less elaborate safeguards against thermal diffusion. Results obtained in the Fe-Cb-0 series in which no scum formed are shown in Table 11. The equilibrium ratio Kl is defined as ph2o/(ph2[%O]). It is related to the equilibrium constant K1 as follows:

Jan 1, 1962

By J. W. Downey, R. A. Morris, M. V. Nevitt

An experimental survey has determined the occurrence of Ti2 Ni-type phases in binary and ternary alloys of Ti, Zr, or Hf with first, second, or third long-period transition metals and also in ternary systems in which 0 is the third component. The existence of eleven previously unreported isomorphs is cited and some approximate phase boundaries are given. Lattice parameters are reported for the new phases. The periodic table relationships involved in the occurrence of the phase are discussed. A previous paper' reported the occurrence of a group of Ti2Ni-type phases (structure-type E93) containing Zr in combination with Rh, Ir, and Pt, and Hf in combination with Rh, Pd, Ir, and Pt, and cited evidence to show that all of the Zr phases and the Hf-Pd phase are not binary phases but occur only when 0 is present. More recently one of the present authors found that in the ternary systems of Ti and 0 with Cr, Mn, Fe, Co, and Ni the occurrence of the Ti2Ni-type phase could be correlated qualitatively with valency electron concentration, and that the role of 0 appeared to be that of an electron acceptor.' This paper describes the results of a broader investigation of the occurrence of Ti2Ni-type phases in binary and ternary systems containing Ti, Zr, or Hf. EXPERIMENTAL PROCEDURE Alloys were prepared by arc melting. The purity of the metals Zr, Rh, Hf, Ir, Pd, and Pt was given in the previous paper.' The additional materials used for this work were metals with a minimum purity of 99.9 pct and reagent grade ZrO2, TiO2, Cr2O3, and NiO. Chemical analysis of several alloys in each system indicated good agreement between intended compositions and cast-button compositions. For the heat treatment precautions were taken to avoid oxygen contamination. The specimens were wrapped in Mo foil and sealed in fused quartz tubes at a room temperature pressure of 1 x mm of Hg. These capsules were then annealed in a vacuum furnace at an external pressure of 5 X mm of Hg. Since the major constituent in most of the alloys studied was the brittle Ti2Ni-type phase, Debye-Scherrer patterns with sharp lines could be obtained with powder crushed from the annealed solid samples without being reannealed. Metallographic, X-ray diffraction, and density determination techniques previously described1, 2 were used. RESULTS AND DISCUSSION Zr-Rh-O, Zr-Ir-Oand Zr-Pt-O Systems-Figs. 1 through 3 show the approximate boundaries of the Ti2Ni-type phase fields at the temperatures indicated in the ternary systems Zr-Rh-O, Zr-Ir-O and Zr-Pt-0. In each isothermal section the Ti2Ni-type phase field is labeled E and the unidentified binary phase found in the previous work' is labeled ?. The dotted lines, which are not phase boundaries, correspond to the composition (Zr2 B)1-xOx. In each system the Ti2Ni-type phase field is displaced to the high-Zr side of this composition line. However, the departures from Zr2B stoichiometry for the metal components are not as high as Zr3B, as was inferred from the previous work. Lattice parameters of the Ti2Ni-type phases in the alloys shown as triangular data points in Figs. 1 through 3 are given in Table IA. The probable compositions of the Ti2Ni-type phases have been estimated from the isothermal sections. Although there are a few exceptions that probably result from uncertainties in phase boundary location and from the effect of variation of oxygen content, the generalization can be

Jan 1, 1961

By P. K. Koh, H. A. Lewis, H. F. Graff

New data on the distribution of silicon between slag and carbon-saturated iron at 1600Oand 1700OC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1'700°C for slags containing up to 20 pct A12O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A12O3-SiO, slags over a range from zero pct Al2O3 to saturation with Al2O3, or CaO.2Al2O3. The upper limit of SiO2 is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/Al203 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al,O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al0 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al2O3 and of Al20,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO2 (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2. The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By J. G. Savins

Certain types of macromolecules added to water and salt solutions flowing in turbulent motion can reduce the pressure gradient. Alternatively, the volumetric capacity of a pipe for these fluids is increased by the presence of these materials. Examples presented show that the drag reduction can become significant. Thus, the presence of 0.28 per cent of a gum derivative in a solution of sodium chloride flowing at 200 gal/min in a 1.89-in. pipe yields a pressure drop which is 0.44 of the single-phase drop measured under the same conditions of turbulent flow; the addition of 0.1 per cent of a vinyl derivative to a I-in. water line yields a throughput capacity which is 1.78 of the single-phase capacity at the same pressure drop. It is further shown that these phenomena are distinctly different from previous observations with other classes of non-Newtonian systems. There a simple lowering of friction factors below the levels predicted from the resistance laws for Newtonian fluids is associated with a suppression of turbulent motion. A rational physical explanation for drag reduction is advanced. Briefly, the proposed mechanism is a storage by the molecular elastic elements of the macromolecules in solution of the kinetic energy of the turbulent motion. INTRODUCTION This study was inspired by a recent review of some paradoxical drag reduction phenomena in turbulent pipe f1ow.I Under very moderate conditions of turbulent flow, the pressure gradient necessary to pump solutions containing certain specific kinds of polymers, fibers and metallic soaps may become appreciably lower than that required* to pump the solvent, i.e., water or a low-viscosity hydrocarbon, under identical flow rates in the same conduit. As shown by our review, this phenomenon of drag reduction in turbulent duct flow was first noted during the second world war, apparently arising in connection with the development of flame warfare weapons. Since that time several papers illustrating this phenomenon have appeared: Toms, Oldroyd,3 Agoston et al., Bundrant and Matthews, Robertson and Mason,6 Ousterhout and Hall,7 Daily and Bugliarello~ Lummus, Anderson, and Fox. 9 That there are practical applications for techniques which increase discharge or decrease the pressure necessary to transport a liquid through a pipeline is illustrated in the patents which have issued which take advantage of this peculiar phenomenon, e.g., Mysels,l0 Dever, Harbour, and Seifert.11 One also finds fragmentary evidence of this effect in the data pertaining to a few of the polymeric solutions studied by Shaver12 and Dodge.13 However, these investigators were concerned with the development of friction factor vs Reynolds number correlations for a variety of non-Newtonian solutions and suspensions, rather than in a study of drag reduction-. A similar kind of drag reduction effect has been observed in gases. Sproull, for example, reports that adding dust to air flowing in turbulent motion through a pipe results in a lowering of the pressure gradient at identical flow rates. There are also military applications for reducing the drag on hydrodynamic vehicles. For example, the possibility of injecting a rheologically complex fluid into the boundary layers of bodies to reduce the skin friction has been investigated by Fabulal5 and Granville.16 Along somewhat different lines are the drag reduction studies of Kramer.17118 He has shown that skin friction can be reduced by covering the surface of a vehicle with a flexible skin. The effect is apparently due to the boundary layer being stabilized by the presence of the skin. Drag reduction by means of coexisting gas and liquid boundary layers, e.g., film boiling and continuous gas injection, has been proposed by Bradfield, Barkdoll, and Byrne,19 Cess and Sparrow,20'21 Sparrow, Jonsson, and Eckert.22 Here the skin friction occurs between a vapor and a surface rather than between a liquid and a surface. There are several references in the literature to friction-factor correlations for non-Newtonian solutions and suspensions: Shaver and Merri11,23 Dodge and Metzner, Clapp,25 and Thomas.26

Jan 1, 1965

By W. L. Austin

AT the Steptoe metallurgical plant, where ore of the Nevada Consolidated Copper Co. is beneficiated, a small copper-leaching annex has been in operation treating flue dust from roasting-furnace dust chambers, together with a siliceous oxidized ore. This leaching plant was designed to obviate smelting low-grade siliceous flue dust, which interfered with the operation of the reverberatories by forming a blanket on the charge The major portion of the copper content of the flue dust accumulating in the upper chambers of the. roaster flue, and at the stack, is water soluble, and also contains much free sulphuric acid and soluble sulphate It was found that sufficient acid could be obtained by mixing this material with water to provide a lixiviant for leaching the siliceous copper o mentioned. This was the sole source of the lixiviant used in the operatic to be described. An analysis of the flue dust showed it to be composed as follows: Per Cent. Copper 3.00 SiO2 23.41 Fe : 4.08 CaO + MgO : 2:72 Al203 6.07 Free H2SO4 19.94 S03 combined as sulphate 25.10 H2O combined With the sulphates 10.67 0 2.50 Total 97.49 Copper soluble in dilute H2SO4 2,56

Jan 7, 1914

By F. C. Bond, J. T. Wang

H. J. Kamack (E. I. du Pont de Nemours & Co., Inc., Wilmington, Del.)—Rittinger's law usually is stated to the following effect: "The work (or energy) consumed in particle size reduction is proportional to the new surface area produced." The law has been stated substantially in this way by Taggart20 Berry21 Dalla Valle22 Coghill and DeVaney,23 Richards and Locke," Gross,25 and many others, and, according to Gaudin,26 was originally expressed by Rittinger in the same form. Consequently there can be little doubt that this is the understanding of the law among most workers in the field of particle size reduction. Bond and Wang, however, express the law in the form "the useful work accomplished . . . ." (italics theirs). The distinction is critical, for in the form used by Bond and Wang the law becomes, as they themselves remark "merely a more or less arbitrary definition of useful work," while in its usual sense the law expresses a physical hypothesis which has been verified experimentally within certain limitations. Considering the way the law has been used, it might be stated more explicitly as follows: "In a given machine operating under a given set of constant operating conditions, the work consumed in the particle size reduction of a given material is proportional to the new surface area produced." Or, as Coghill and deVaney have said,27 "the (Rittinger) law holds only when the tests being compared are made under analogous conditions." There are occasions when the law transcends these limitations; for example, the surface area produced per unit energy consumption for a given material in a ball mill does not vary much over a fairly wide range of operating conditions. But by and large, the surface area production per unit energy consumption will vary with the operating conditions, the type of machine, and the material. The essence of Rittinger's law is that the surface area production per unit energy consumption is independent of the particle size, and this has been verified experimentally by numerous workers for numerous materials, within certain limits. An important limitation is that when one grinds to very small particle sizes, agglomerative forces may tend to interfere with size reduction so that the surface area increases less rapidly than Rittinger's law would predict. Within such limitations, Rittinger's law can be regarded as empirically established. The law has, however, certain theoretical implications, and it seems to be chiefly against these that Bond and Wang direct their criticism. Solids are believed to possess surface energy which is proportional to surface area. Thus, Rittinger's law implies a proportionality between surface energy produced and mechanical energy expended (for a particular material in a particular machine). It does not imply that all or most of the mechanical energy is transformed into surface energy; in fact it is known that most of the mechanical energy is transformed into heat. Bond and Wang assert that most of this heat arises from the damping of elastic vibrations of stressed particles. This may possibly be true for crushing (with which they are chiefly concerned), although in grinding it is probable that much of the heat arises from friction between particles. However, the fact that the surface energy is small compared to the heat energy does not invalidate Rittinger's law, which implies merely that they are proportional. The authors also criticize Rittinger's law on the grounds that "this theory cannot be justified mathematically, since work is the product of force times distance, and the distance factor is ignored," and "energy input must be the product of force times distance, and the Rittinger theory completely ignores large variations in the distance (strain dimension or deformation) throughout which a force must act to produce breakage of different materials." However, the quantities force and distance as such are irrelevant to Rittinger's law, which considers energy input as an integral quantity. The fact that different materials require different forces and strains (hence, different amounts of energy) to break them is incontrovertible but again is irrelevant to Rittinger's law, which, as mentioned before, applies -only to a single material. Even in theory, it would not be expected that the surface area produced per unit energy consumption would be the same for different materials, because the surface energy per unit area is presumably specific to each material. Bond and Wang advance another argument of a

Jan 1, 1952

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918