Search Documents

By Walter von der Linden

INTRODUCTION There are three essential components for a modern longwall mining system: the coal cutting/loading machine, the self-advancing supports and the longwall conveying system. The latter consists of a face conveyor, a stageloader and a belt tall section arrangement (Figure 1). The longwall face conveyor is an integral component of the face equipment and has a threefold purpose: 1) continuous coal haulage. 2) track for cutter/loader . 3) reference/anchor rail for roof support advance. Further requirements for the longwall conveyor are horizontal flexibility for conveyor advance without interruption of haulage and cutter/loader tramming and vertical flexibility to cope with seam undulations.

Jan 1, 1981

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

Jan 1, 1894

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall's work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann's approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen's approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

If problems are opportunities in disguise, the mining industry certainly had plenty of "opportunities" in 1975. Considering the industry's generally lackluster 1975 profit record, and in view of the slowdown in inflation, there's some hope that 1976 might be a better year in spite of the increasing risks and uncertainties that plague the mining industry.

Jan 2, 1976

By C. K. Leith

Jan 1, 1906

We have seen that the first coal development in Pennsylvania was in the Pittsburgh bed in the southwestern corner of the state. The next mining, in point of time, was done in Clearfield County along the West Branch of the Susquehanna River, but the amount of mining done was quite small for a number of years and was soon exceeded by that from the area north of the Susquehanna River in Tioga, Bradford and Lycoming Counties, which will be considered now. It is claimed that coal was first noticed in Tioga County, in 1792, by Robert and Benjamin Patterson who were leading a party of settlers from Williamsport to southern New York, and while clearing a road near the site of Blossburg, found coal, which was said to be good. About 1815 David Clemons made an arrangement with Aaron Bloss, owner of the land, to work some of the coal and hauled the first load down the river to Painted Post, N. Y., as there were no available markets in his own state. Smiths found it an excellent fuel and apparently he found a ready market for the small amount he could transport by wagons and sleighs. As wood began to become scarce around the towns in New York State, the knowledge of the coal deposits in the mountains at the head of the Tioga River attracted attention to the field and the necessity, for means of transportation from it. Some coal had been floated down the river, but navigation was uncertain and dangerous. In 1827 an iron plant was built, and to ship its product and coal, it was proposed to build a canal along the river to reach Corning, N. Y. A company had been chartered in 1826 in Pennsylvania to "make a navigable canal or slack-water navigation" to the state line and coal was shipped on rafts of logs, both being sold, during highwater. In 1828 the company was authorized to build a railroad instead of a canal, and in September 1840, the railroad was completed from Corning to Blossburg.1 That some coal from Pennsylvania had been reaching southern New York towns prior to the improved means of transport is shown by the report of a committee to the New York Assembly: "the bituminous coal has been brought to us either from Great Britain or from that part of our own country which borders on, and lies west and south of the Susquehan-

Jan 1, 1942

By R. W. Raymond

The Mining Law of New Pork, contained in Title XI., Chapter IX., Part One of the Revised Statutes, is as follows: Section 1. The following mines are, and shall be, the property of the people of this State in their right of sovereignty : (1.) All mines of gold and silver discovered, or hereafter to be discovered, within this State. (2.) All mines of other metals discovered, or hereafter to be discovered, upon any lands owned by persons not being citizens of any of the United States. (3.) All mines of other metals discovered, or hereafter to be discovered, upon lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain less than two equal third parts in value of copper, tin, iron, and lead, or any of those metals. Sec. 2. All mines and all minerals and fossils discovered, or hereafter to be discovered, upon any lands belonging to the people of this State, are, and shall be, the property of the people, subject to the provisions hereinafter made to encourage the discovery thereof. Sec. 3. All mines of whatever description, other than mines of gold and silver, discovered, or hereafter to be discovered, upon any lands owned by a citizen of any of the United States, the ore of which, upon an average, shall contain two equal third parts or more, in value, of copper, tin, iron, and lead, or any of those metals, shall belong to the owner of such land. Sec. 4. Every person who shall make a discovery of any mine of gold or silver within this State, and the executors, administrators, or assigns of such persons, shall be exempted from paying to the people of this State any part of the ore, produce or profit of such mine for the term of twenty-one years, to be computed from the time of giving notice of such discovery, in the manner hereinafter directed. Sec. 5. No person discovering a mine of gold or silver within this State shall work the same until he gives notice thereof, by information in writing to the Secre-

Jan 1, 1888

By R. W. Raymond

Four portraits have recently been hung in the rooms of the Institute, in recognition of four illustrious men with whom we, as mining engineers and metallurgists, may claim fellowship. Luther. Martin Luther is often spoken of as a miner's son; but it is less generally known that John Luther, his father, was, in a small way, a metallurgist as well as a miner, and that Martin Luther himself, in his youth, worked in a forge or bloomary established by his father at Mansfeld, Saxony. Since this is the only manual occupation on his part of which we have ally record, it is fair to assume that the great scholar and reformer derived from his work in this department the practical familiarity with the conditions of human labor so abundantly evinced in the homely illustrations which accompany even his serious arguments, and in the witty apothegms of his famous " table-talk." At the same time, I must confess that I have not been able to find in any of the works of Luther distinct allusions to mining or metallurgy. Körner. Theodor Körner, a student at the Mining Academy of Freiberg, Saxony, threw himself into the German War of Freedom in the first decade of the 19th Century. He was a poet of no mean rank; and his " Song of the Sword " is one of the great lyrics of literature. This poem was written but a few days before he died in battle. In many respects, Körner may be compared with our American hero Theodore Winthrop, who similarly met a glorious fate, and left behind him prophetic indications of geniue, of which his premature death prevented the complete fulfillment. I am informed by a member of the Institute that Körner's admirable collection of minerals is still preserved at Dresden.

Jan 1, 1909

By R. E. Head, E. L. Tucker

In the metallurgy of precious metals, it has been standard practice for years to use cyanogen compounds, so it was but natural that early investigators in the field of flotation should consider these compounds as possible flotation reagents. In Australian Patent 9508, of 1913, alkali cyanides were described as suitable reagents for the separation of heavy sulfide minerals, the reagents being employed either in an alkaline or neutral circuit. In U. S. Patent 1236501, of 1917, to John M. Tibbet, the use of cyanide in conjunction with soda ash or lime is described. One of the claims of this patent reads, "An improvement in the cyanide process for the treatment of ores comprising, mixing the ore with cyanide solution and oil and alkali: emulsifying the oil in the presence of the ore, the alkali and the cyanide solution, floating a portion of the values in the pulp by producing gas bubbles in the mixture and removing the values floated." More recently, Sheridan and Griswold, in U. S. Patents 1421585 and 1427235, describe a somewhat similar process and have successfully introduced it in the mill of the Timber Butte Milling Co. U. S. Patent 1429544, of 1922, to Stevens, describes the use of double cyanides of copper, zinc, and lead. The success of cyanide as a reagent in the differential flotation of lead and zinc sulfides in highly complex ores is proof that these patents have a solid foundation. Although the technique of their application to particular ores has been worked out in many cases, no one, so far as is known, has attempted to describe the nature of the action of the cyanide or to determine the ideal conditions for its application. It was the purpose of the present investigation to gather information on these points. Naturally this would have been an exceedingly ambitious program had the attempt been made to study the effect of cyanide

Jan 1, 1926

By P. J. Dean

This Paper contains a comprehensive survey of the known electron-hole radiative recombination mechanisms in the family of III-V compounds. Because of space limitations, the luminescence properties of each III- V compound are not reviewed separately and exhaustively. Instead, the different known types of recombination processes are discussed in turn and exemplified with reference to the III- V compound in which they were first recognized, or are best understood. Electron-hole recombinations usually occur predominantly at impurities or lattice defects either introduced de1iberately or inadvertently present, but radiative intrinsic interband electron-hole recombinations, which occur in perfect crystals, have been observed. Recombination processes which involve the participation of impurities or lattice defects ("extrinsic" recombinations) considered include transitions in which a) free carriers recombine with carriers trapped at impurities ("free to bound" transitions) , b) electrons bound at donor impurities recombine with holes trapped at acceptor impurities ("donor-acceptor pair" recombinations), C) excitons bound to charged or neutral donor or acceptor impurities recombine radiatively (both "resonance" and "two-electron" "bound exci-ton" transitions have been observed), d) excitons bound to neutral donor or acceptor impurities recombine non-radiatively (an example of an "Auger" recombination), and e) excitons bound to impurities with the same number of valence electrons as the host atom which they replace ("isoelectronic " traps) recombine radiatively. In addition, Auger recombination processes involving one or more free carriers have been observed. These extrinsic processes all involve impurities which are present as point defects. Some apparently well-authenticated examples of the recombination of excitons bound to complex impurity-lattice defect centers including nearest-neighbor donor-acceptor pairs are also discussed. Identificalions of the transitions involved in stimulated emission from the direct gap III-V compounds are briefly reviewed. Although the examples of these recombination mechanisms are selected from the III-IV compounds ia this review, these processes have quite general relevance in semiconducting crystalline solids; irrdeed most of them have also been identified in the 11- VI compounds and elernental semzconductors. THE development of crystal growth and purification techniques in recent years and concurrent advances in the understanding of physical processes in solids has accelerated the development of a wide variety of solid-state electronic devices of proven utility. These de- vices are generally used for switching or amplifying operations in electrical circuits. Most solid-state circuit elements are very photosensitive. This photo-sensitivity is generally undesirable and the single-crystal chip forming the active portion of the solid-state device is mounted in an opaque container. The photosensitivity is made use of in phototransis-tors and photodiodes, which are among the most sensitive detectors of electromagnetic radiation particularly in the near infrared.' In these devices, light is converted into electrical power. The solid-state lamp utilizes the inverse effect, namely the conversion of electrical power into light. There is an increasing tendency to use single-crystal diodes rather than the earlier electroluminescent cells in which the active material is present as a powder embedded in a suitable dielectric.' The radiation is emitted at a rate far in excess of the thermal equilibrium rate for the frequencies and temperatures involved; i.e., luminescence occurs. The development of practically efficient solid-state lamps is at an early stage compared with solid- state circuit elements or even photodetectors. Considerable progress has been made in recent years, however.3 The present review is devoted to a survey of the radiative recombination processes in the semiconducting compound crystalline solids formed from elements in groups I11 and V in the periodic table. These materials exhibit the full range of known recombination processes in solids. In fact many of these processes were discovered in 111-V semiconductors. Nonradiative recombination processes, which control the lutninescence efficiency, are also discussed. Luminescence is efficiently excited in semiconductors through processes which produce large excess concentrations of free electrons and holes in the energy bands of the crystal. Transitions induced by lattice defects or impurities usually predominate in the recombination process. By contrast, luminescence in the conventional fluorescent lamp is excited by optical absorption at the luminescent impurity center itself (the activator) and/or at a second type of impurity center (the sensitizer). This latter type of photoluminescence process, occurring in doped ionic crystals with wide band gaps, is outside the scope of this review.4 I) ENERGY BAND DESCRIPTION OF ELECTRON STATES IN CRYSTALS The energy band description of the energy states available to an electron in a crystal forms the basis of our understanding of the empirical division of crystalline solids into metals, semiconductors, and insulators in accordance with their electrical and optical properties.' Nonmetallic crystals have a finite energy gap between the highest energy band which is

Jan 1, 1969

By L. W. Kempf

THE thermal expansion characteristics of aluminum alloys have been examined by several investigators, among whom may be mentioned Shakespear,1 Schulz,2 Hidnert,3 Hidnert and Sweeney4 and McCullough.5 Shakespear compared the expansion of a series of aluminum alloys containing 14 per cent copper, with separate additions of about 1 per cent each of manganese, tin and zinc with that of pure copper. Schulz examined the expansion of aluminum and zinc and some aluminum-zinc alloys. Hidnert determined with a high degree of precision the expansion characteristics of pure aluminum, some aluminum-copper, aluminum-zinc, aluminum-silicon and some commercial alloys. Hidnert and Sweeney examined the expansion characteristics of aluminum-beryllium alloys. McCullough, by an interferometer method, determined the expansivity of some aluminum-copper, aluminum-magnesium, aluminum-iron, aluminum-nickel, aluminum-silicon and aluminum-manganese alloys. Incidental to an investigation carried out during the past six years and leading to the development and exploitation of an aluminum piston alloy of relatively low thermal expansivity, the expansion characteristics of a wide variety of alloys were examined. Some of the data which might be of general interest are gathered in this paper.

Jan 1, 1933

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

THIS paper describes the application of amine flotation to a specific problem-that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. SAMPLES Two samples, designated "minus 100mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.1 per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1945

By J. F. Bryson

Instantaneous outbursts of coal in underground workings have occurred frequently in various coal fields in Nova Scotia; British Columbia; Canada; South Staffordshire, England; and the states of Washington, Virginia, West Virginia and eastern Kentucky in the United States. Such outbursts in eastern Kentucky have been called "mountain bumps " because they are more likely to occur under mountain cover than elsewhere, but recently they have become generally known as "coal bumps." The eastern Kentucky coal field has been troubled by these outbursts since 1923. Many men have been injured and killed, and the morale of the workmen in the vicinity of such outbursts has been affected to such an extent that mine production has suffered for a considerable period following each outburst. Such phenonlenal occurrence in any coal field naturally has led to discussion as to the cause and means of prevention. In the eastern Kentucky field, local mine officials, workmen, mining engineers, and many others have offered many ideas as to the cause and many methods of prevention have been suggested, and tried without success. Some of the plans were either practically or economically unsound and in general impossible to follow. To enumerate all the suggestions would require a large volume. One cause mentioned was that they might be due to gas under high pressure, as in Lower Silesian mines, and the remedy reeommcnded was to drain the gas by drilling holes into a suspected area. A hole 30 ft. long was drilled into a 60-ft. pillar to allow the gas to drain off, hut the pillar bumped the next day. Realizing the importance of obtaining the best information available on coal bumps, the writer, with the permission of the Harlan County Coal Operators' Assoeiation, invited Mr. George S. Rire, Chief Mining Engineer of the U.S. Bureau of Mines, who had investigated bumps in several countries, to conduct an investigation of coal bumps in this field. Mr. Rice, by permission of the Director of the G.S. Bureau of Mines, accepted the invitation, and it was the writer's privilege, in company with

Jan 1, 1936

By J. F. Bryson

Instantaneous outbursts of coal in underground workings have occurred frequently in various coal fields in Nova Scotia; British Columbia; Canada; South Staffordshire, England; and the states of Washington, Virginia, West Virginia and eastern Kentucky in the United States. Such outbursts in eastern Kentucky have been called "mountain bumps " because they are more likely to occur under mountain cover than elsewhere, but recently they have become generally known as "coal bumps." The eastern Kentucky coal field has been troubled by these outbursts since 1923. Many men have been injured and killed, and the morale of the workmen in the vicinity of such outbursts has been affected to such an extent that mine production has suffered for a considerable period following each outburst. Such phenonlenal occurrence in any coal field naturally has led to discussion as to the cause and means of prevention. In the eastern Kentucky field, local mine officials, workmen, mining engineers, and many others have offered many ideas as to the cause and many methods of prevention have been suggested, and tried without success. Some of the plans were either practically or economically unsound and in general impossible to follow. To enumerate all the suggestions would require a large volume. One cause mentioned was that they might be due to gas under high pressure, as in Lower Silesian mines, and the remedy reeommcnded was to drain the gas by drilling holes into a suspected area. A hole 30 ft. long was drilled into a 60-ft. pillar to allow the gas to drain off, hut the pillar bumped the next day. Realizing the importance of obtaining the best information available on coal bumps, the writer, with the permission of the Harlan County Coal Operators' Assoeiation, invited Mr. George S. Rire, Chief Mining Engineer of the U.S. Bureau of Mines, who had investigated bumps in several countries, to conduct an investigation of coal bumps in this field. Mr. Rice, by permission of the Director of the G.S. Bureau of Mines, accepted the invitation, and it was the writer's privilege, in company with

Jan 1, 1936

By C. A. Stickels

The preferred crystallographic orientations developed during recrystallization of polycrystalline electrolytic iron sheet, cold-rolled 90 pct, were ivestigated. Recrystallization at 500° or 565° C for relatively short limes produces a texture which is similar to the rolling texture. A duplex partial fiber texture, significantly different from the rolling texture, is found when the annealing time is increased. Recrystallization at 700°C also produces a sequence of textures with increasing annealing time. In order of their appearance, these textures are: 1) the duplex partial fiber texture found at lower temperatures, 2) a four-component texture "near {322}(296)", 3) a {112)(110) +(111)(110) texture, and 4) a two-component "near {554)(225)" texture. Secondary recrystallization, or discontinuous grain growth, accompanies the development of the latter texture. However, the "near {554} (225)" texture was nol observed when secondary recrystallization occurred under other conditions. All of the ideal orientations found in recrystallization textures can be accounted for by the growth of minor components of the deformation texture. IN recent years there has been increased interest in improving the drawability of metals by controlling the preferred crystallographic orientation of the sheet.1-l3 Since more low-carbon steel is drawn than any other material, considerable attention has been focused on the properties of sheet steel. Efforts to improve drawability through texture control have been hampered by the lack of any published systematic study of the recrystallization textures developed in iron annealed below Acl. The purpose of the present work was to supply some of this missing information, specifically, the recrystallization textures obtained by isothermal anneals of polycrystalline iron, cold-rolled 90 pct. LITERATURE REVIEW—DEFORMATION TEXTURES Barrett14 reviewed and summarized the investigations of rolling textures in iron and low-carbon steel prior to 1952. The texture of heavily deformed iron (rolled 90 pct or more) is described as consisting of two partial fiber textures. The dominant fiber texture (designated here as fiber texture A) has a (110) fiber axis in the rolling direction and includes the orientations (001)[110], {112}( 110), and {111}(110). The secondary texture (designated here as fiber texture B) is described as having a (111) fiber axis in the sheet normal direction, and includes the orientations {111)( 110) and (111)(112). Since the publication of Barrett's book, there have been two detailed studies of the deformation texture in polycrystalline iron. In both instances, the more sensitive diffractometer methods of pole-figure determination were used. Bennewitz15 studied the cold-rolling textures developed in polycrystalline low-carbon steel and a 3 pct Si steel. He determined (110), (2OO), and (222) pole figures for specimens reduced 30, 50, 60, and 90 pct and analyzed his results in terms of partial fiber textures. He distinguished three stages in the development of the final deformation texture. 1) Grains rotate to form two incomplete fiber textures, with (110) fiber axes inclined 30 deg to the sheet normal toward the rolling direction (fiber texture B). After 50 pct reduction, the highest density of poles is near an ideal orientation {554}(225), the two components of which are members of this duplex fiber texture. 2) With increasing amounts of reduction, grains rotate about the former fiber axes toward ideal orientations of the type {112)( 110) (common to fiber textures A and B). 3) Finally, grains rotate about their ( 110) axis in the rolling direction, clockwise and counterclockwise from the orientations {112}(110). This produces the range of orientations from (111)(110) to (001)(110) commonly found in the rolling texture of heavily deformed iron (fiber texture A). No significant difference was found between the deformation textures of low-carbon and silicon steels. A few years earlier, Haessner and weik16 had determined (110) pole figures for carbonyl iron rolled to 30, 60, 80, and 90 pct reduction in thickness. heir data agree quite well with the more complete data of Bennewitz, but a somewhat different description of the evolution of the deformation texture was given. The appearance of (110) poles in the transverse direction is ascribed to a (100)[011] component rather than "near {554}( 225) " components, and the (110) fiber axes of fiber texture B are described as located 35 deg rather than 30 deg from the sheet normal. Both of these studies agree that the secondary texture present in heavily rolled iron, the duplex fiber texture B, has (110) fiber axes and not a single ( 111) fiber axis normal to the sheet, as

Jan 1, 1965

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By C. C. Harris

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale-down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By Charles H. Shamel

I fear most of the Institute members are already weary of the perennial controversy about the apex law. I feel that way about it myself now, though I have been guilty of considerable contribution- to the discussion in the past. The discussion does not seem to perceptibly influence previously held views and I would not again break into print on the subject but for the urgent invitation of the Chairman of our Law Committee. This energetic and able member has firmly determined to secure a revision of the mining law and among other things to eliminate the so-called apex provision from the U. S. mining statutes. He is, however, fair about it and has invited me to make ((the strongest possible argument in its favor." I am suspicious that he is acting on the psychological principle that it is usually easier to convince an audience against a cause vigorously but unsuccessfully defended than against one wholly mute. Nevertheless, I realize that personally he wishes me no harm, much as he hates the apex law, and so am willing that the Institute have whatever benefit may accrue from my taking up again the unpopular side of the discussion. I say this because the attitude of a large part of our "articulate" membership seems irreconcilably hostile; their minds are made up; favorable consideration is foreclosed; and they become impatient and even sarcastic at any attempt to elucidate a favorable view of the apex law. The exact question for discussion at the present time is not whether on abstract, or any other considerations, the apex law is the best possible rule, but the very different proposition whether, after nearly 50 years of statutory life and much longer as a practically universal miners' custom, it is now just and expedient to repeal the apex law. At this point it seems to me that we may profitably devote a paragraph or two to the subject of the origin of law in general, as we are presumed to be considering the subject from the high viewpoint of the general welfare of the nation. The most comprehensive and accurate definition of law in the legal sense is, that it is the body of rules for the regulation of human conduct which is enforced by the State, that is, by the nation.l Legal

Jan 1, 1915

By Henry D. Hibbard

The finishing and casting temperature of steel is a subject concerning which there is so much to learn that some temerity is required to write about it. This paper is, therefore, suggestive rather than dogmatic, though the views expressed seem now to the writer to be correct; nevertheless, they may be modified by future developments or discoveries but until then may be of some utility, particularly to beginners in the making of steel. Consideration is limited to the temperatures of simple steels, also called carbon steels, which are those in which carbon is the only element introduced for the purpose of conferring desired physical properties. Alloy steels will receive attention later. Three things largely determine what a batch of steel really will be; via., composition, casting temperature, and rate of teeming. Each has its advocates as being the most important; but they are so interrelated that each must conform to or be right for the other two. When one is claimed to be the most essential to have right, that, probably, was the one that it was found had to be of a certain description, within narrow limits, to suit the already adopted variations of the other two; that is, it was the last of the three to be brought into line. The term "casting temperature" is rather indefinite as there ale several temperatures to which the term may be applied. Most writers who have mentioned casting temperature of steel have alluded to it in relative terms. The few who have given actual temperatures, including Langmuir, Burgess, Styri, and Bash, do not give full information about them. Their results demonstrate the efficiency of pyrometers used rather than aid the steelmaker. In order to understand and use the temperatures, one should know in each case what the steel was, the stage at which the temperature was taken, whether it was usual or not, and whether or not it was right for that steel at that stage. When these

Jan 1, 1925