Search Documents

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low, a medium, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0% ash, as follows: from low-volatile anthracite, 0.7%; from medium-volatile coal, 1.0%; and from high-volatile coal, 2.3%. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0% or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a convc.ntiona1 dense-media washing plant. Anthracite preparation practices during much of the industry's history were geared to maximum recovery of the larger sizes, pea through egg, which were used in hand-fired, domestic furnaces. Those sizes were cleaned to meet trade requirements, and the smaller sizes were usually higher in ash content. The impression, thus, was that ash content of anthracite always increased as the sizes got smaller. It was presumed that it was impossible to wash the finer sizes to extremely low ash contents. Following World War 11, the classical domestic market began to decline and the finer sizes assumed an increasingly large share of the market. For example, in 1949l 61% of the production was still pea and larger. Fig. l2 shows that -by 1955 these sizes accounted for only 50%, and in 1965, they were only 39% of the total anthracite produced. With the reduction in the market, increased quality was demanded, especially in export markets, and an increasing number of dense-media magnetite washers were installed in new and existing cleaning plants. In 1965, the coarse coal prepared at 59 breakers in the anthracite fields was sampled by the U.S. Bureau of Mines (USBM); approximately 50% of these plants were equipped with dense-media magnetite washers.3 Since 1950, more attention has been focused on the use of finer sizes for numerous industrial uses, including iron-ore sintering, pelletizing, foundry coke-making, cement manufacture, production of calcium carbide, and of carbon electrodes, etc. Most industrial uses require relatively clean anthracite, such as 10 to 11% ash for sintering and foundry coke, 7% for aluminum melting-pot cathode carbon, and 5% for carbide production. Hence, cleaning methods have been improved to the extent that dense-media washers, hydraulic cyclones, and flotation cells have been introduced as fine-coal-cleaning devices. It is now possible to wash the buckwheat, rice, and barley sizes (9116 X 3132-in.) to ash contents as low as 8 to 10% in dense-media devices, but washing the -3132-in. sizes to those limits presents more difficult problems, due mainly to the fineness of the material. This USBM investigation was conducted to determine the amount and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. The goal was to reduce the ash content to a level acceptable for industrial carbon uses, including electrode manufacture, which generally requires an ash content of 1% or less. While low-ash content is of primary importance in selecting industrial carbons, the amounts of other constituents are also important, including iron, silicon, titanium, nickel, vanadium, and sulfur. They were not considered in this work, since their occurrence in deashed anthracite has been studied elsewhere.4 The results of the present investigation were used to design a flowsheet, suggesting a method for producing ultraclean anthracite as part of conventional preparation practice, using dense-media vessels, crushers, pulverizers,

Jan 1, 1970

By Keith R. Bock, Norman Parlee, Albert M. Barloga

Coils of pure iron and iron-carbon alloy wire (0.05 to 0.80 pct C) and sufficient sulfur to saturate the solid phase were equilibrated in evacuated or argon filled tubes. After rapid cooling, and removal of the outside nonmetallic layer, the wires were analyzed for carbon and sulfur and the data used to construct an Fe-S binary and isotherms of the Fe-C-S ternary in the range 1149° to 1427°C. THE solid solubility of sulfur in steel is of interest in connection with such phenomena as hot shortness, burning, and so forth. "Burning," the more or less permanent damage that some steels suffer when heated for forging or rolling, has been shown to be related closely to the behavior of sulfur and less closely to carbon and oxygen.' Attempts to interpret burning phenomena in steels fail because of lack of data on the Fe-C-S and the more complex systems in this family. Rosenqvist and Dunicz 2 and Turkdogan, Ignatowicz, and pearson3 have largely elucidated the Fe-S diagram in the region of interest but no information on the Fe-C-S diagram in this region appears to be available in the literature. This paper deals with the elucidation of the Fe-C-S diagram in these interesting ranges. The method employed is different from those used by previous workers2'3 on the Fe-S system. EXPERIMENTAL METHOD Pure iron wires (Ferrovac E) or iron carbon alloy wires of 1 mm in diam were cleaned with acid and acetone, coiled, and placed in silica tubes (7 mm OD and 5 mm ID) previously closed at one end. Enough sulfur was added to assure saturation of the solid iron phase. The filled tubes were either simply evacuated and sealed, or filled with argon at a reduced pressure and sealed. The argon was required at the higher temperatures to prevent collapse of the tubes. The filled and sealed tubes were placed in the middle uniform temperature zone of a Globar tube furnace and equilibrated at temperatures ranging from 2100°F (1149°C) to 2720°F (1493°C). After equilibration the tubes were removed from the furnace and quenched in air or water, the form of quenching being found to have no effect on the results. The tubes were broken open and the coils were placed in a 1 : 1 HC1 solution to remove the sulfide-rich layer. The coils were then cut into small pieces and analyzed for sulfur and carbon. In the early stages of the investigation different equilibration times ranging up to 17 hr were tried and the cores of the wires were analyzed to test for saturation. One hour appeared to be sufficient to reach maximum sulfur content at 1454°C and 2 hr sufficient at 1149°C. The practice adopted was to use at least 3 hr at the higher temperatures and at least 5 hr at the lower temperatures. The iron-carbon alloy wires used were made by carburizing pure iron wire with carbon monoxide gas in a one inch diameter ceramic tube at about 1204°C. Differing carbon contents were obtained by allowing fairly large coils to react with the gas for varying lengths of time at a flow rate of 800 cc per min. The reacting times ranged from 15 min to 4 hr depending upon the amount of carbon desired. The furnaces used were controlled by means of Leeds and Northrup Speedomax Type H instruments with D.A.T. Control attachment. Thermocouples were calibrated against the melting points of gold and copper. The temperatures recorded appear to be accurate within i2.7OC. Starting with run No. 85 and continuing with the

Jan 1, 1962

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.' Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650' to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 1/4 to M in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles. Because rock salt is an inexpensive commodity, a low-cost process was required. Gravity methods were, of course, considered. The heavy-liquid separations indicated that a split at an effective specific gravity of 2.2 to 2.3 would be required. (The specific gravity of pure halite is 2.16.) Heavy-media separation was investigated but had the disadvantages that it was necessary both to operate with saturated brine and to dry the cleaned salt, and that the cleaned salt was darkened by the magnetite medium. Air tabling was tried but did not give the desired separation. It soon became apparent that established methods would not provide a satisfactory solution and work was undertaken on the development of a new process to solve the problem. PROCESS DEVELOPMENT Preliminary Experiments: At the start of the investigation, an analysis of the problem indicated that the diathermacy of rock salt—that is, its ability to transmit radiant heat—might form the basis for an efficient separation process. Under this theory, the impurities might be selectively heated by radiant heat. The particles could then be fed over a belt coated with a heat-sensitive substance so that the warm impure particles would adhere preferentially to the coating. After the initial experiments, made by heating the rock salt with an infrared lamp and separating the product on small sheets of resin-coated rubber, proved encouraging, a small continuous separation unit was set up. This comprised 1) a simple heating unit consisting of a vibrating feeder covered with aluminum foil and an infrared lamp mounted above the feeder and 2) a separation belt 6 in. wide and 36 in. long. A sketch of the device is shown in Fig. 1. Results with this apparatus confirmed the fact that a good separation was possible. It was apparent, however, that a considerable amount of experimental work would be needed to develop the scheme to a practical and economical process. The Process: Basically, the process consists of two main steps: 1) selective heating by radiation and 2) separation of the heated particles on a heat-sensitive surface. Because neither of these steps had previously been utilized commercially in mineral processing, it was necessary to do basic research on both aspects. Factors studied in the investigation included type of heat source, design of heating unit, design of separation belt, selection of heat-sensitive coating, removal of heated particles from the belt, contact between particles and coating, and maintenance of the heat-sensitive surface. Part of the experimental work was carried out on a small-scale unit consisting of the 36x6 in. belt and auxiliary apparatus, and part on a larger unit. For simplicity, discussion of work on both of these units is grouped together. SELECTIVE HEATING Radiant-Heat Source: The essential requirements for a radiant-heat source were 1) that the radiant heat be in a wave length range which is effectively absorbed by the impurities but not absorbed appreciably by the rock salt and 2) that it be dependable, practical, and economical. Selection of a heat source of suitable wave length range was one of the first considerations. It is well known that pure halite is highly transparent to radiant energy in wave lengths from 0.3 to 13 microns. However, the available data on infrared transmission by dolomite and anhydrite, particularly in the range below two microns, were not complete enough to serve as a reliable basis for selection of a heat source. Although it may have been possible to obtain sufficient data on infrared transmission and absorption to enable one to select the best heat source, a more direct procedure was used. This consisted simply of exposing the crude rock salt to each of several types of radiant-heat source on the small continuous separation device. The heat sources investigated, approximate source temperature used, and calculated wave length of maximum radiation are tabulated in Table I. Of the two types of tungsten-filament lamps investigated, both the short wave length photoflood lamps and the longer wave length infrared lamps were satisfactory from the standpoint of selectivity

Jan 1, 1961

By Frank Feuille, Edward Schuster

As the time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W. Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.' Colombia requires foreigners to agree to be bound by its alien law. In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. alongitsland

Jan 1, 1923

By Edward Schuster, Frank Feuille

As the time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W. Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.' Colombia requires foreigners to agree to be bound by its alien law. In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. alongitsland

Jan 1, 1923

By J. W. Clark, C. T. Sims

Wrought chromium-base alloys containing yttrium, cubic monocarbides of the Ti(Zr)C type, and similay alloys containing manganese and rhenium have been melted and fabricated. Strength has been studied by hot hardness and elevated-temperature tensile and rupture measurements, low-temperature ductility by tensile testing, and surface stability by oxidation testing. In additiod, studies have been conducted of the carbide stability, and of aging behavior. The carbide dispersion generates effective elevated-temperature strength, which is further enhanced hv strain-induced precipitation. The dispersion exhibits classical dissolution and aging response. The ductile-to-brittle transition temperature of these alloys is above room temperature. The alloys reported show fairly good oxidation resistance, but nitrogen contamination can cause fortnation of a hard Cr2N layer under the oxide scale. Manganese does not appear to be a promising alloying element in chromium. In the years 1945 to 1950, the metal chromium was considered as a possible base for alloy systems due to its considerably higher melting point than superalloys, its low density, its high thermal conductivity, and its apparent capacity for strengthening. However, this interest in chromium was short-lived. It was found difficult to melt and cast, to be exceptionally sensitive to the effect of minor imperfections, to have a lack of ductility at both room and elevated temperatures, and to be subject to a deleterious effect of alloying elements upon the ductile-to-brittle transition temperature.' Since then, chromium, as a practical alloy base, has remained virtually unstudied. Further, purposeful ignoring of chromium has been promoted by statements that its bcc structure would not allow it to be strengthened to useful values, when compared to the "austenitic" alloys.2 Recently, a new look has been taken at chromium-base alloy systems. Study of the literature will show that chromium, providing some of its disadvantages could be eliminated or minimized, actually has a rather attractive potential as an alloy-system base. Analysis of rather scattered data suggests that chromium is quite capable of being strengthened to high levels. Also, significant strengthening of its two sister elements in Group VI-A, molybdenum and tungsten, has been demonstrated in a number of commercial and exploratory alloys. Chromium should be similar. Since chromium does not readily form a volatile oxide like tungsten or molybdenum, it offers a much higher probability of giving birth to alloy systems with useful oxidation resistance. Concerns about possible high elemental vapor pressure have been mitigated by recent data.3 In addition, the physical properties exhibited by chromium are attractive for application as a high-temperature structural material. For instance, its thermal conductivity varies from 49 to 36 Btu-ft/hr-sq ft-°F over its range of usefulness (which is two to four times higher than most superalloys), its density is about 7.2 g per cc (20 pct less than most nickel-base alloys), its coefficient of thermal expansion varies from 4 to 8 x 10-6 per OF, and it has a relatively high modulus of elasticity, approximately 42 x 10' psi.4 Alloying studies on a chromium base in the past have usually encompassed rather sweeping solid-solution alloy additions for strengthening. This is not consistent with contemporary alloying practice in Group VI-A. For instance, molybdenum, also in Group VI-A, is primarily alloyed for strength improvement by use of heat-treatable carbide dispersions.5 Chromium and molybdenum are similar in their chemical activity and other properties. Thus, strengthening of chromium by carbide dispersions was studied. Chromium-base alloys are plagued with room-temperature brittleness, although high-purity unal-loyed chromium can be made ductile.4,8 Use of yttrium as a scavenger has done much to improve ductility and resistance to nitrogen embrittlement in chromium systems,7 so it was utilized in this program. It has also recently been found8 that small rhenium additions (1 to 5 pct) create improvement in the ductility of Type 218 tungsten wire. This is apparently related to the remarkable effect of rhenium additions near its terminal solid solubility in all Group VI-A metals.9'10 Investigation to establish if dilute concentrations of rhenium would also be effective in chromium appeared to be logical for this program. Since rhenium is too expensive to be practical in alloys for application as structural components, ductility improvements through solid-solution alloying were also sought by substitution of manganese for rhenium; manganese, like rhenium, exists in Group VII of the periodic system. The optimum amount of carbide dispersion for chromium-base alloys was obtained by analogy with molybdenum. Strengthening in molybdenum is achieved by use of Ti-Zr carbide dispersions. A

Jan 1, 1964

By Joseph G. Debanné

Foreword The three case histories and the liquid fuels planning scenario presented in this paper span a twenty year period, from the pioneering days of computers in the petroleum producing industry during the mid-fifties, to the energy crisis era of the seventies. Inasmuch as two of the main actors, Ian McKinnon and I, are featured in all three case histories, while I am currently involved in the fossil fuels scenario, this paper provides four related and personal spot readings along an evolutionary path: from the one dimensional technical domain to the multi-dimensional techno-socio-economic domain of computer applications in the petroleum industry. Coincident with this evolution in the direction of increasingly comprehensive and powerful computer applications, the evolution in hardware/software capability and in analytical power are also kept in perspective. The three case histories are: 1. The Bonnie Glen-Wizard Lake Case (Calgary, Alberta, 1955-1957); 2. The TransCanada-Great Lakes Gas Transmission Case (Ottawa-Washington, 1966); 3. The Westcoast Transmission - El Paso Pipelines Gas Export/ Import Case (Ottawa-Vancouver-Washington, 1966-1967). The liquid fuels planning scenario is a demonstration exercise rather than a case history; however, it represents an important point on the evolutionary curve and, provides a concrete example of tech-

Jan 1, 1977

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By Hertha Freche

THE diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magne-sium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austen1 carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum.

Jan 1, 1936

By E. C. Mahan

THE text of my talk was suggested by the invita-tion of your secretary, who said that the excess productive capacity of the bituminous industry was a matter of common concern to engineers and coal operators. Cognizant of the depressed condition of the industry, he tactfully added that in common council we might find wisdom. Certainly it would seem that the application of the best engineering knowledge available would be helpful in solving mining problems. There is no doubt that clear thinking, characteristic of the engineering type of mind, is essential to untangle the shapeless pattern which increased complication, so often mistaken for progress, has developed. There is much thinking today which neither looks forward to a logical combination of ideas nor backward to simple fundamentals. The result of that sort of thinking is hopeless confusion. Lately we have heard much about excess capacity and overproduction, along with their attendant evils. Respecting the bituminous coal industry, these terms have been frequently misused. How many of us have seen them applied to the coal industry but how few of us have understood them. I am reminded of a state-ment which William Green, president of the American Federation of Labor and a former miner from the Ohio field, gave to the Associated Press last month, in which he was quoted as saying: "The coal men must realize that conditions have altered since the World War. To-day they are producing a billion tons a year, with a market for only half that tonnage." I cite this instance as a glaring example of the flood of. loose statements about the bituminous industry with which the public is being deluged. If the general public, or some of the newspapers, had any passion for the facts, this sort of misleading statement would not get very far. Unfor-tunately, in these days, opinions are more sought after than facts, and statements by such a person as Mr. Green and are promptly accepted by a credulous public.

Jan 4, 1928

By Arthur B. Cummins

Diatomite is a siliceous rock of sedimentary origin, which may vary in degree of consolidation, but which consists mainly of the fossilized remains of diatoms. These are microscopic algae of the order Bacillaria. Diatomite is a unique form of silica, there being nothing else found in nature or produced by the manufacturing arts, that has its characteristic physical structure. There are numerous sediments which contain some diatom residues, admixed with a substantial amount of other materials-clay, carbonates or silica. While these are classified as diatomaceous silts, shales, or mudstones, they are not properly diatomite, a designation which is restricted to material of such qualities that it is suitable for commercial uses. The terms diatomaceous earth and kieselgur are synonymous with diatomite. The expressions infusorial earth and tripolite are obsolete. Diatomaceous silica is a definition best used to distinguish the basic component of diatomite, that is, the substance of the silica shell itself and is the major constituent of beneficiated diatomite or processed diatomaceous products. Some highly indurated materials, such as cherty shale, porcelanite, and opaline cherts which have resulted from diagenetic changes cannot be considered as diatomite although they may have been derived therefrom. On the other hand, diatomaceous oozes or loose sediments consisting mainly of diatom residues with or without much organic matter are source materials in process of becoming diatomite. Composition and Properties Pure diatomite is composed of opaline or hydrous silica, with small amounts of associated inorganic components-alumina, iron, alkaline earths, alkali metals, and minor constituents, all of which may occur in solid solution or as an essential part of the opal complex. Crude diatomite on the other hand may contain variable amounts of organic matter and soluble salts, and the usual contaminants of sedimentary formations-particles of rockforming minerals, sand, clay, or carbonates. As occurring in nature, diatomite contains an unusual amount of free water, which may vary from 10 to 60 pct or more. Diatomite, in the dry deposits which are characteristic of most of the important world deposits, occurs as a lightweight, comparatively light colored, "chalklike" material. The apparent density (dry basis) in situ varies from 20 to 40 lb per cu ft. The structure may be either massive or finely stratified. The earth is highly porous, usually soft and easily friable. It is nonreactive with acids and may be tentatively identified by the above characterizations. Confirmation is by microscopic examination which readily reveals the nature of the material. In deposits which contain organic matter the appearance of the material is totally different. The color may vary from light tan or gray to brown, greenish or nearly black. There is frequently difficulty in distinguishing it in the field from peatlike materials, but the difference is readily apparent after calcination. Powdered diatomite or diatomite products have an apparent density (loose weight) of 5 to 16 lb per cu ft, wet densities of 10 to 30 lb per cu ft, specific gravities 1.9 to 2.35, index of refraction 1.42 to 1.48. Diatomite is essentially micro-amorphous, but does show some tendency toward orientation in structure after a cristobalite pattern. Amorphous silica has been considered as a random association of cristobalite crystallites, the size of which are only slightly larger than a unit cell.20 The prop-

Jan 1, 1960

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By R. L. Ash, R. R. Rollins, C. J. Konya

An investigation was performed to determine conditions for optimizing the spacing of simultaneously initiated multiple explosive columns. This was done by using models of mortar, dolomite, and Plexiglas with 10-grain mild detonating fuse as the explosive charge. It was desired to simulate blastholes with multiple primers initiated by detonating fuse or when high-velocity explosives are used in low-velocity materials. It was found that optimum spacing between multiple charges was strongly influenced by charge length. At less than optimum charge length, the spacing at which complete shearing was possible between adjacent charges decreased exponentially with a subsequent loss of broken material volume. For charges fired simultaneously, larger burdens and spacings were possible as compared to those necessary for single-crater charges. For each material studied, there was a characteristic optimum charge length and a maximum attainable spacing at any given burden. Proper selection of the spacing distance between charges is fundamental to successful blasting. Its value directly affects the cost of drilling and explosives used per unit of broken material. In addition, the choice of a spacing that is Compatible with a given set of blasting conditions aids in the control of fragmentation sizing, ground vibrations, overbreak, and throw which in turn, influence other production costs. For example, normally loaded blastholes that are spaced too closely invariably promote overbreak and usually give coarse fragmentation. Unless care is taken, airblast and violent flyrock will occur and under certain conditions cutoffs and misfires may result. Too large a spacing, on the other hand, frequently leads to conditions that form bootlegs or toes. The choice of a particular spacicg to use, however, is largely a matter of individual experience and judgment, usually based on trial and error. Very little is known or can be found in the literature with regard to how the spacing between charges is related to field conditions and charge geometry. As a general rule, the firing time sequence of adjacent charges and properties of a material are thought to have the most significant influence on the spacing distance best suited for any given field condition. For example, delayed initiation of adjacent charges usually always requires a closer spacing than when charges are fired at the same time. This should be expected if one considers that the energy normally dissipated and lost in the surrounding ground from charges fired independently would be captured and utilized for breaking material between charges when they are initiated together. Spacing can be extended also when charges are aligned with structural planes of a material, such as jointing, along which shearing is relatively easy. It is customary to relate the spacing (S) between charges to their common burden (B) in the form of a spacing ratio, or SIB. The burden normally is considered as the optimum depth or distance from any single charge perpendicular to the nearest free or open face at which the desired fragmentation and maximum crater yield are obtained. For production blasting, value of the ratio is generally considered to vary from 1 to 2, depending on conditions.1-6 When adjacent charges are fired independent of one another, the value varies from 1 to about 1.4, the closer amount being employed to square corners or produce craters having the ideal 90" apex angle. The larger ratio is the geometric balance value for craters having an apex angle of 135". The basic ideal crater forms in the plane of the charge diameter for charges fired independently are shown in Fig. 1. In the event charges are fired simultaneously, geometric balance in the plane of their charge diameters suggests that a spacing ratio near 2 would be appropriate, as illustrated by Fig. 2. In practice, however, some compromise ratio value must be selected to conform with the specific ground conditions. An example would be where the jointing planes tend to produce 60° or 120° crater angles, the appropriate geometrically balanced charge arrangement being given by Fig. 3. In this condition, the spacing ratio is 1.15, not 1 or 1.4 as suggested for the 90° cratering of independently fired adjacent charges. In view of the foregoing, it would seem logical to assume that whenever charges all having the same burden are fired at the same time, spacing distances always can be greater than those permitted by charges fired independently. In practice this is not the case, however.

Jan 1, 1970

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By William E. Ford, Edward Salisbury Dana

The Niobates (Columbates) and Tantalates are chiefly salts of metaniobic and metatantalic acid, RNb2O6 and RTa2O6; also in part Pyroniobates, R2Nb2O7, etc. Titanium is prominent in a number of the species, which are hence intermediate between the niobates and titanates. Niobium and tanta¬lum also enter into the composition of a few rare silicates, as wöhlerite, låvenite, etc. The following groups may be mentioned: The isometric PYROCHLORE GROUP, including pyrochlore, microlite, etc. The tetragonal FERGUSONITE Group, including fergusonite and sipylite. The orthorhombic COLUMBITE Group, including columbite and tantalite. Also the orthorhombic SAMARSKITE GROUP, including yttrotantalite, samarskite, and ånnerodite. The species belonging in this class are for the most part rare, and are hence but briefly described.

Jan 1, 1922

By CHARLES M. SCHWAB

THE ENGINEERS have placed this great country of ours in a preeminent position with everything pertaining to manufacture, metallurgy, and the kindred arts. We are second to none in the world. We have a country which, another speaker has said, God has endowed with such riches in coal and natural resources as no other country in the world. But rich as these are, there is one thing greater; the sturdy character, energy, and integrity of its people, which will make these great resources an influence in the world's developments. Great as are these resources and the energy and integrity of our people, there is one problem of our .engineering, which I term human engineering, that is of far more importance than the creation of machines and methods, with which you have been so successful in the past. Of what value is the skillfully devised machinery, the complex process, unless manned and operated by people whose heart and soul are in sympathy with the work they are doing and who have before them the giving of a complete day's work for a day's pay?

Jan 1, 1920

By Dr. O’Neil Thomas J., Donald W. Gentry

"October. This is one of the peculiarly dangerous months to speculate in stocks. The others are July, January, September, April, November, May, March, June, December, August and February." -Mark Twain Although the preceding chapters describe the type of preliminary evaluation frequently performed in the mining industry, it has been assumed that input data are known with certainty-clearly an enormous simplification. In reality, estimates of ore grade, mining cost, metal price, etc., are subject to varying degrees of uncertainty due to the inability to predict the future with much precision. Management would probably not, for example, be equally attracted to two projects each offering a 20% DCFROI-one for a new gold venture in Nevada and the other for an undersea manganese nodule operation in the Pacific. The high risk with the latter investment tells the obvious; there is more to investment decision-making than a deterministic analysis using "best estimates" of input parameters. The science of decision theory normally distinguishes between decisions under uncertainty, where probabilities of various outcomes are unknown; and decisions under risk, where such probabilities can be estimated. The first case is rarely en- countered in practical capital investment analysis in mining, so the remainder of this chapter focuses on that class of problems where rational probability distributions for the future states of input variables can be estimated. RISK IN MINING Risk in the context of this chapter is the unforeseen deviation of individual cash flows from expected values for a capital project. For a mining venture, the source of this uncertainty could be any number of factors relating to such items as ore grade, ore reserve tonnage, operating costs, product prices, etc. With conventional *Adapted from O'Neil, T.J., 1979, "Procedures for the Preliminary Financial Evaluation of Metal Mining Ventures," Computer Methods for the 80s, A. Weiss, ed., AIME, New York, pp. 556-573.

Jan 1, 1984

By Gerhard Derge

THE extension of metallurgical control of steelmaking processes has always made it desirable to have some quick method for determining the oxygen content of molten steel. To meet the practical demands of the steel industry, this method must also be simple enough so that the sampling can be done by the regular furnace crew. This requirement was kept in mind continually in the work to be described. An oxygen value is required for proper control, whether it be of a rimming steel or of a fully killed steel. However, two factors have discouraged the development of such direct methods: I. The reaction C + FeO -+ Fe + CO is rapid enough to make the correct sampling of the bath a difficult problem. The most generally accepted means of circumventing this difficulty have been the aluminum-killed bomb test of McCutcheon and Rautio1 and the aluminum-killed spoon test of Herty.2 The theory of these tests is that all of the oxygen in the iron is converted to A1203, which can then be determined by chemical methods. Even when simplified so that the analysis is made by a measurement of turbidity, this method is too slow to be used in routine control. Furthermore, the results obtained have never been entirely satisfactory, and some of the reasons for this will be discussed later in this paper. 2. The ordinary chemical methods of analysis for oxygen in steel are not reliable. The only analysis that seems to possess sufficient dependability to be of value is vacuum fusion,3 and the apparatus and technique developed for this have been too complex and slow for routine work. INDIRECT METHODS Indirect methods of estimating the oxygen have been resorted to in mill practice. Generally these depend upon the chemical equilibria involved. The oxygen in the bath is related to other components in the slag or metal that can be analyzed more readily. These methods have many difficulties in common. Steelmaking processes involve a complicated set of interrelated reactions, all of which tend to approach equilibrium at varying rates. The degree to which any particular equilibrium is approached, is not , well established. Moreover, a proper use of theoretical equilibrium constants requires a more extensive knowledge of the activities of the reactants than we now have. This is well illustrated by the irregularities observed when trying to determine the oxygen in the metal by its ratio to the iron oxide in the slag. Equilibrium relations may be used more readily if they are evaluated by plant experience, but the extent of approach to equilibrium remains an undetermined variable and lack of an entirely satisfactory means of determining oxygen for the calibration is felt keenly. For example, the statistical analysis of the relation between carbon and oxygen4 5 illustrates that even in a single plant wide variations exist under normal conditions of operation. Nevertheless, this is one of the best methods now

Jan 1, 1943