Search Documents

By AIME AIME

THREE of the addresses presented at this interesting and important session are printed in full else- where in this issue. The fourth, Mr. Hewett's paper, on "Cycles In Metal Production" has been issued as Technical Publication 183, and an abstract of it was published on page 162 of last month's issue. The general discussion that followed these four important papers is given in full below. S. A. TAYLOR: I would like to ask Mr. Veasey whether the control of oil in pools includes royalties, and, if so, in case of a new pool how are you going to control, or rather how are you going to describe the limits of that pool?

Jan 1, 1929

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By Basil B. Zavoico

PRODUCTION of crude it in the United States during 1939 totaled about 1.255,776,000 barrels, an average of 3,440,482 barrels per day, 3.41 per cent above the 1938 output of 1,214,355,000 barrels but 1.83 per cent below the record pro¬duction of 1,279,160,000 barrels, in 1937. However only the two-week shutdown of oil fields in the Southwestern States in August and September prevented the domestic crude production from establishing an all-time record in 1939. Demand for all petroleum products for the first ten months of 1939 showed an increase of 7.04 per cent over the similar period of 1938. Domestic demand for all petroleum products was particularly benefited by the increasing industrial activity, advancing 8.37 per cent above the like period of the preceding year equivalent to a volume increment of 256,810 barrels per day; with motor-fuel demand gaining 5.83 per cent and demand for all fuel oils gaining 12.15 per cent over the corresponding period of 1938. The export demand for the first ten months of 1939 was slightly below the export movements during the same period of 1938, declining 0.56 per cent. The European war was a major factor in 1939 for the petroleum industry in the United States, even if, at the end of the year, the war had not yet resulted in the expected large shipments to England and France.

Jan 1, 1940

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1938

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1937

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1952

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburgh, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1923

By C. K. Leith

THE outstanding fact of the mineral world today, at home and abroad, is the surplus of current production, and particularly of capacity for production, over current requirements. This is not by Any means a new condition, but never before has it loomed up in such' menacing form. - Those of us who have devoted most of our professional efforts to the discovery and development of 'new mineral supplies now suddenly find ourselves with the job apparently accomplished, waiting for some one else to find an outlet for excess mineral production before we can further. The management of the industry is in much the same boat. The psjrcho16gy of the industry has been so grooved in the direction of acquisition of, minerals that at the present moment the mineral industry confronts the new problem of surplus in more or less of a daze.

Jan 1, 1931

[Executive J. V. W. REYNDERS, Chairman WILLIAM H. BASSETT E. DEGOLYER I-I. C. BELLINGER RICHARD PETERS, JR. Finance GEORGE OTIS SMITH, Chairman H. A. GUESS F. JULIUS FOHS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A. MOSMAN H. K. MASTERS J. A, SINGMASTER Alternates F. G. BREYER C. W. HAMILTON F. E. PIERCE]

Jan 1, 1928

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By J. C. Bokros, A. S. Schwartz

The irradiation-induced densification of pyrolytic carbon has been shown to take place by a simple first-order rate process. The values of the densification constant, kd, for isotropic carbons are 1.0 x 10-22, 1.4 X 10-22 and 2.8 X 10-22 (nut)-1 at irradiation temperatures of 520o, 670°, and 1000oC, respectively. The apparent activation energy obtained from the temperature dependence of kd for isotropic carbons is about 0.2 ev. Estimates of the maximum stresses that develop in isotropic carbons owing to shrinkage onto an unyielding support show that stresses in excess of 15,000 psi may be avoided during irradiatian at 600" and 1000°C if the initial coating density is kept above 1.5 and 1.9 g per cu cw, respectively. If a carbon coating on an unyielding support is not completely isotropic, stresses may continue to build up at high neutron exposures after densification is complete because of continued anisotropic distortion. Stresses in excess of 15,000 psi from this source may be avoided during irradiation at 1000°C if' the Bacon anisotropy factor is kept below 1.3. A variety of applications of carbon and graphite in nuclear technology has stimulated numerous studies of the effect of neutron irradiation on these materials One of the most interesting problems associated with the use of carbons and graphites in the high fast neutron fluxes of nuclear reactors arises as a consequence of the neutron-induced dimensional changes that occur during irradiation. Energetic neutrons displace car- bon atoms from their lattice positions; and, depending on the temperature, the interstitials and vacancies produced migrate to form clusters, recombine, or are annihilated at dislocations or crystallite boundaries. The competition of various sinks for the point defects results in structure-sensitive bulk-dimensional changes that vary with temperature in a complicated way. This paper deals with the neutron-induced dimensional changes in turbostratic carbons that are being used as coatings on nuclear fuel particles. Details of the structure of these carbons and the variations of their structure with deposition conditions have been reported.'-3 It has been shown in previous work that the neutron-

Jan 1, 1968

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

Jan 1, 1970

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors' point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By Arthur Notman

IN VIEW of the wide publicity given to the charges by the Couzens Committee of the United States Senate of discrimination by the Bureau of Internal Revenue in favor of the copper companies, it becomes a matter of interest to consider the basis for these charges. The point to be determined is whether they rest on a foundation of fact or are purely and simply matters of opinion. The whole question boils down to the purpose of the Tax Law as applied to mines, which is to afford the same protection to them as provided for all other taxpayers, namely: that they were to be allowed to pay back as depletion to their owners the values of their properties as they existed or were estimated to exist on May 1, 1913, free from tax. To determine these valuations it was? necessary to select from a wide range of possibilities a set of values for a number of essential factors.

Jan 1, 1925

By A. T. Yu

On March 18, 1964, the 52,000 dwt ore carrier M/S Houn Maru called at the port of Coquimbo, Chile, on its maiden voyage to take iron ore to Japan. This marked the first time a vessel of this size ever arrived at Coquimbo, and the event promises to drastically accelerate henceforth iron ore exports from Coquimbo province. This was made possible by the use of a versatile shiploading system recently installed by Cia. Minera Santa Fe. Coquimbo has no mechanized loading facilities other than six conventional 5-ton cargo cranes. Limited space on shore further complicates the stocking problems. To make the best of what is available, a meticulously organized semi-hand-loading system has been developed through the years.

Jan 5, 1964

By Howard N. Eavenson

DURING the past year, as in the preceding ones, prices continued to fall, production to decrease, and more mines were closed. Much attention is being given by the industry to suggested plans for betterment of its position, and if the scheme recently brought out for consolidation of sales agencies into district agencies is loyally carried out, it cannot but help to improve conditions. The progress in the anthracite industry is shown in the report of its chairman, E. H. Suender; changes in coal preparation are outlined in the report of J. B. Morrow, chairman of Committee on Coal Preparation, while increased mechanization of the western mines is described by Eugene McAuliffe, chairman of the Committee on Machine and Strip Mining. In spite of the depression, interest in the Coal Division has been increasing, its meetings have been well attended, and its committees are active and have been doing excellent work.

Jan 1, 1932

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

By Charles Hart

A STUDY of the various ores that have been discussed impresses one with the need of beneficiation, in many cases. This applies to the ores that have lain dormant, due to necessity for further preparation, or to ores that now find a market due to a changed condition. Processes of beneficiation will come into their own as our richer ores become exhausted. Many efforts at improvement have been commercial failures, due to prematurity. Thomas A. Edison, with characteristic foresight, attempted concentration of the low- grade New Jersey magnetites some thirty years ago. Due to high costs and the discovery of the Mesabi range, his efforts were futile. However, a successful crusher, designed by Mr. Edison, resulted from this attempt. Agglomeration of concentrates had not, at that time, been brought to its present efficiency, when sinters and briquettes of excellent physical condition are obtainable. Recent efforts in the beneficiation of the lean magnetites of the East Mesabi resulted in an excellent sinter, but that operation is also ahead of its time.

Jan 1, 1929