Search Documents

By J. C. Scully, G. Sanderson

The electrolytic formation of y hydride in thin foils of Ti-5Al-Z.5Sn alloy and four Ti-A1 binary alloys has been studied by electron microscopy and electron diffraction. Two orientation relationships have been found: THE adsorption of hydrogen by titanium alloys from aqueous solutions has been widely reported. This can occur, for example, in both alkaline' and acidic2 pickling baths, in chemical polishing374 and electro-polishing Solutions,3,4 during cathodic polarization5" and under certain corrosion conditions,7,8 Etching reagents may also produce visible precipitates, sometimes after an aging period.9 During an investigation into the stress corrosion susceptibility of a titanium alloys by thin foil electron microscopy many observations have been made of hydride precipitation which has been deliberately promoted by techniques that are described below. The characteristics of hydride precipitation are reported and the observed crystallographic orientation relationships are discussed with reference to distortion in the titanium lattice created by the presence of the hydride. EXPERIMENTAL TECHNIQUE One grade of commercial titanium and five alloys were examined. Their composition and hardness values are shown in Table I. All the materials were in the form of thin sheet, 0.05 to 0.065 cm thick, which had been annealed after cold rolling. Foils suitable for transmission electron microscopy were made in two ways: a) by chemical polishing; and b) by elec-tropolishing. The solution used for chemical polishing was a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. During this polishing specimens were manually moved up and down in the solution. The reaction was veFy rapid, specimens thinning to foil thickness (2000A) in 5 min. Since chemical polishing solutions tend not to cause hydride contamination if they are kept cool3 no attempt was made to prevent the solution from becoming hot during the thinning operation. Electropolishing was performed at -30° C with a mixture3 composed of 295 cu cm methyl alcohol, 175 cu cm n-butyl alcohol, and 30 cu cm perchloric acid with an applied voltage of 40 v after chemically thinning specimens to approximately 0.017 cm thickness in a cool solution of 44 pct HF, 40 vol H2O2, and water in the volumetric ratio 1:6:3. EXPERIMENTAL RESULTS 1) Ti-5A1-2.5Sn Alloy. The Ti-5A1-2.5Sn alloy was severely contaminated by hydrogen during the chemical polishing. Foils obtained in this way contained large amounts of the y hydride phase. A typical micrograph is shown in Fig. l. The laths were identified as the hydride phase by selected-area diffraction of a large number of foils examined in a tilting stage that could be turned through 40 deg. Using the lattice spac-ings of the alloy obtained by X-ray diffraction as a standard the a value of the hydride was determined fromo the electron diffraction patterns to be 4.38 to 4.40A. The accuracy of this figure is only about ±2 pct. Further evidence of the identification was obtained by vacuum annealing chemically polished foils of the alloy at 500°C. This resulted in the dissociation of the hydride with the production of dislocations and possibly vacancy loops as shown in Fig. 2. The hydride

Jan 1, 1968

By C Gunther

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By D. W. Gentry, H. E. Sherer

Determining the age at which to replace a specific piece of mining equipment, and choice of the best possible replacement, is a problem common to nearly all mining operations. This paper examines the data required for intelligent equipment replacement decisions and discusses how to predict future repair cost from historic data, determine the total cost of various replacement alternatives, and evaluate the different replacement alternatives. Various operations research and computer methods were used to develop this easily-used, practical equipment replacement method.

Jan 1, 1984

By Francis P. Sinn

LOW prices have made 1938 a difficult year for the zinc industry of the world. Particularly in the United States, output had to be radically curtailed to bring production into line with consumption. Despite these unfavorable conditions, some additional plant construction is contemplated. In Jugoslavia, through co-operation with the Government, Trepca Mines is lo build a zinc plant to produce 10,000 metric tons annually, the plant to be ready for operation in July, 1941). Cerro de Pasco is proceeding with its plans for an electrolytic plant in Peru. A pilot plant, to be ready next summer, is under construction. In eastern Canada an electrolytic plant is planned in Quebec to treat concentrates from Yoranda and other mines but no defi-

Jan 1, 1939

By R. A. Vandermeer, J. C. Ogle

Two distinct types of depth-dependent variations in texture have been observed in niobium cold-rolled various amounts up to 99.5 pct reduction in thickness. These nonuniformities are thought to be the results of nonhomogeneous plastic dewmation during rolling. The first type is characterized by a zone at intermediate depths that tends to lack certain strong orientations which are present in the surface and center layers of the rolled stock. This type of texture modification seemed to be associuted with "high" body rolling and may be related to the shape of the zone of deformation in rolling. The second type of texture inhomogeneity found involved the formation of a unique texture in the surface layers of heavily rolled strip. High fiiction forces between work piece and rolls appear to be needed to generate and maintain this texture. We believe that this unique surface texture results from a shear mode of deformation in the surface layers. THE evolution of texture in both the surface and center regions of cold-rolled niobium as a function of increasing deformation from 43 to 99.5 pct reduction in thickness was reported in a previous paper.' It was noted that for strips rolled between 95 and 98 pct reduction a distinctly different texture appeared in the surface layers which was unlike the center texture. Certain other layer to layer textural variations were also detected during the experimental phase of that work but were not described in the paper. Surface textures have been reported previously for the bcc materials iron and Steel2-4 and are well known in the fcc metals.5 It is usually stated that these are shear textures which arise under conditions of high friction between specimen and rolls. Work by Mayer-Rosa and Haessner5 n niobium rolled under conditions presumed to be high roll friction gave no indication, however, of a surface texture in that material. This is indeed puzzling in view of our results.' Thus we undertook additional experiments designed to study the stability of the surface texture for certain rolling variables. The variables investigated were the presence or absence of lubrication, amount of reduction per pass, and reverse vs unidirectional rolling. It is the purpose of the present paper to describe the kinds of depth-dependent textural inhomogeneities that we have observed in rolled niobium as well as to present the results of our recent experiments on the stability of the surface texture. Possible explanations for the depth-dependent texture variations will be discussed in terms of nonhomogeneous plastic deformation during rolling. EXPERIMENTAL Specimens cut from the niobium rolled to different reductions in the previous study1 were examined at various layer levels throughout the strip thickness for textural inhomogeneity. The specimen surfaces were either etched or machine ground and etched to remove material to a specific depth. Textures were determined by means of the Schulz X-ray reflection pole figure method with a Siemens texture goniometer and Cum X radiation. Since the important intensity peaks of the textures in niobium are usually located on the normal direction (N.D.) to rolling direction (R.D.) radius of the (110) pole figures, it was sufficient in many cases to scan only along this radius. At selected depths or where additional information was required the entire (110) pole figure was also obtained. In studying the stability and formation of the surface texture, experiments were conducted on 0.400-in.-thick, fine-grained, randomly oriented niobium specimens extracted from the same starting stock as that used in the earlier study.' Two of these specimens were rolled at room temperature to a total reduction of 96.4 pct. One was rolled between cleaned and degreased rolls with no lubrication. The other was lubricated between passes with Welch Duo Seal vacuum pump oil. The rolling schedules of each were kept as nearly identical as possible. Drafts were of the order of 0.006 to 0.012 in. per pass. Other experiments consisted of rolling specimens at constant fractional reduction per pass, i.e., (ta- tb)/ta equals a constant where ta and tb are the entrance and exit thickness of the rolled stock, rather than at a constant draft, i.e., ta- tb equals a constant. Ten specimens were rolled at room temperature on a two-high, motor-driven rolling mill with 8-in.-diam rolls. These specimens were rolled to thicknesses of between 0.041 and 0.073 in. (82 to 90 pct total reduction) at approximately constant reductions per pass ranging from 9 to 45 pct. Kerosene was used as a lubricant. Half of the specimens were always rolled in the same direction while the other half were reversed end to end at each pass. The texture in the surface regions was determined with the X-ray technique described above. RESULTS The textural inhomogeneities noted in niobium rolled from fine-grained, randomly oriented stock 1.5 in. long by 0.75 in. wide by 0.40 in. thick can be classified into two types. The first may be discussed with the aid of Figs. 1 to 3. Fig. 1 is a three-dimensional plot of the X-ray intensity in units of times random vs f , the angle from the N.D. to any point along the N.D. to R.D. radius of the (110) pole figure, and depth, given as percent of the thickness (?t/to X 100, where at is the thickness of material removed and to is the as-rolled

Jan 1, 1970

By Charles W. Goodale

In the course of the preparation of my paper on " The Occurrence and Treatment of the Argentiferous Manganese Ores of Tombstone District, Arizona" (Dam., xvii., 767), my attention was called to two patents which have been issued for the use of a diaphragm at the upper end of a Howell furnace, whose importance merits more than a passing reference. Mr. J. K. Pardee invented and first put into use in the Algon quin mill, at Philipsburg, Mon., in 1880, a ('new' and useful im provement in rotary ore-roasting furnaces," which was intended "to increase the capacity, effectiveness and working economies of such furnaces." The following description and accompanying figures are taken from the patent papers, dated December 21st, 1880: Fig. 1 is a side elevation of the feed-end of the Howell rotary furnace, with parts broken away, the better to exhibit my invention. Fig. 2 is an end elevation of the same. Fig. 3 is an end elevation of the same, showing a modification of my invention. In operating a furnace of this kind, of the capacity of one ton of ore an hour, it was found that for the best work the two fire-places (one at each end of the revolv ing cylinder) consumed about ten cords of wood every twenty-four hours, and that about twenty-fonr tons of silver-ore were introduced through the feed-pipe. It was also found that of the amount of ore, fully one-third did not go through the revolv ing cylinder, but went into the dust-chanibers about the feed-end of the furnace or cylinder, and this ore going into the dust-chambers was found not to be sufficiently chloridized for amalgamation, but had to be re-roasted. I then caused to be made, out of boiler-plate iron, a segment of a circle, the height of which was about one third of the diameter of. the cylinder or furnace, the circumference of the circle being smaller than the circumference of the furnace, so that about a half-inch space would be left between the plate and the furnace, when said plate or segment was in position. This segment or plate of iron was then fastened to the bottom of the feed pipe, as shown in the drawings, wherein A represents the revolving cylinder or furnace; B, the fire-place and dust-chambers at the feed-end of said furnace; C, the inclined feed-pipe, and D, the diaphragm, partition, or plate fixed within said furnace, A. With the diaphragm or plate, D, in the position shown, the furnace was run for about a month, and it was found that with the furnace in best working condition only four cords of wood every twenty-four hours were consumed, that no fire was required at the feed-end of the furnace, that not one-twelfth of the ore

Jan 1, 1890

By Bernard Kopelman

THE particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by com¬mercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature, and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. REVIEW OF THE LITERATURE Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.1 When reduction of tungsten oxides by H2 was introduced commercially, 2.1 several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-13 While these many investigations were in fair agreement on the equilibria there arose considerable controversy as to the chemical composition of the oxide between W03 and W02, because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 10o years. Thus Malguti,14 in 1835, decided it was W02.56. In 1857, Riche" proposed the formula W308. Usler,16 in 1865, confirmed the existence of W308 and further proposed W4O11. In 1897, Desi17 agreed upon W308 but also found W5014.

Jan 1, 1946

"The Garfield plant of the American Smelting & Refining Company is situated about seventeen miles west of Salt Lake City, on the Los Angeles & Salt Lake Railroad, and has freight service by the Denver & Rio Grande Western, Western Pacific and Bingham & Garfield Railways.The site lies between the picturesque Great Salt Lake, with its mountain islands, and the northern point of the Oquirrh Range, which forms the western boundary of the Salt Lake Valley.The location includes several hundred acres of land rising from the southern shore of the lake, selected on account of its adaptability to the economical handling of materials by gravity methods.The smelter is a custom smelter, treating copper ores and concentrates produced in Utah and adjoining states.The ores treated consist mainly of oxides from the Tintic and Park City Districts, sulphides from Bingham District, and concentrates from the mills of the Utah Copper Company, from mills in California, and copper precipitates from the Ohio Copper Company. The last product comes from low grade ores of Bingham Canyon.The following figures represent approximately the daily consumption of materials:Ores and Concentrates…2,700 tonsLime sand…100 ""Coal…350 ""Oil for Roasters…240 Bbls."

Jan 1, 1925

By Earl H. Miller, Henry H. Bruhn

COMMERCIAL beds of sylvite ore were discovered by the Snowden & McSweeney Co. while drilling a wildcat oil well some 25 miles northeast of Carlsbad, N. NI., in 1925. After a preliminary core drilling program the U. S. Potash Co. sank a 1060-ft shaft within 4 miles of the original discovery. This shaft was in an isolated location in a sand desert area with only the roughest of dirt roads connecting it with the neigh- boring town of Carlsbad some 21 ½ miles west.

Jan 6, 1954

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE,. Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 8, 1914

H. N. EAVENSON, Gary, W. Va.-Judging from our own experience, the statement that only 40 per cent. of the accidents are caused by the human element is very low. We have adopted all the measures that Mr. Wilson recommended, such as systematic timbering, use of permissible expolsives and practically everything that anybody has suggested or can think of, and even after all that has been done, done for several years, and a systematic campaign maintained all the time to reduce accidents, we still

Jan 4, 1918

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman. WILLARD S. MORSE, Vice-Chairman. . THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON, Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 6, 1914

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York, L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS Chairman. RUSH J: WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER FRANCIS A. THOMSON,

Jan 2, 1915

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York. N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 9, 1914

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman. WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN; Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 1, 1915

By John W. Buch

IN my review a year ago I pointed out that a small coal-mining companies as well as large had decided that the so called ?central shop? was a benefit. These central shops replaced in a large measure the commercial shops operated by those who have no direct connection with production of cod. Central shops in this time of salvage and major repairs have proved their worth. In addition, many of the larger companies had in their central shops equipment available for the production of many thousands of parts for our vast war machine and, as subcontractors, are doing this type of work. This is a real contribution to the war endeavor. Lack of new supplies has resulted in exhaustion of those stocks formerly stored or hidden in underground shanties. This means that the small stock of repair parts likely LO be available to any mine

Jan 1, 1943

The President was authorized to appoint a committee comprising himself and five others, to draft an amendment to the Constitution for the purpose of bringing before the membership the suggested change in qualifications for members. The President thereupon appointed the following Committee: Edwin Ludlow, Chairman, B. B. Thayer, J. W. Richards, G. C. Stone, C. F. Rand, and P. N. Moore. The President was authorized to arrange with the Bureau of Mines for the payment of the necessary clerical assistance to copy the inventory of

Jan 8, 1917

Executive FREDERICK M. BECKET, Chairman HOWARD N. EAVENSON J. V. W. REYNDERS H. A. GUESS WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL H. MERCER H. G. MOULTON Admissions JOHN M. LOVEJOY, Chairman GEORGE D. BARRON DONALD M. LIDDELI. E. V. DAVELER W. D. B. MOTTER, JR. Alternates AMOR F. KEENE L. F. STROBEL SAM TOUR Membership LEWIS B. LINDEMUTH, Chairman EDWARD H. ROBIE, Secretary Executive Committee NELSON DICKERMAN FREDERICK LAIST FRED H. KAY THOMAS T. READ H. A. KURSELL A. T. SHURICK SAM TOUR

Jan 1, 1932

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W, FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W..RODDEWIG, Vice-Chairman. LYNDON K, ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 7, 1914

By Robert M. Lewis

At the Scotia plant of Blue Diamond Coal Co., near Cumberland Ky., good recovery and grade can be obtained when floating deep mine coal. When the plant changes over to strip coal, flotation fails, resulting in loss of coal. A procedure was developed at the Minerals Research Laboratory in Asheville, N. C., for recovering strip coal by flotation. Laboratory results were duplicated on a batch scale at the plant. The procedure was found to be effective when tried on a continuous basis in the processing plant.

Jan 1, 1973