Search Documents

By C. Y. Cheng

THE purpose of this note is to show that the dislocation mechanism controlling the creep of Fe-4 pet Si alloy1 may equally account for the behavior of a-Fe2 over the same temperature range. A recent study of the creep behavior of a-Fe has been made by Ishida et al.2 Their results were in agreement with the mechanism of nonconservative motion of jogged screw dislocations over the entire range of temperatures investigated, from 480° to 1045°K. However, the observed creep rate was much higher than that which could be accounted for by the above model unless the authors assumed that pipe diffusion became significant below 775°K. More recently, Cheng et al.1 inves-gated the creep of Fe-4 pet Si alloy over about the same temperature range and found that the results could be correlated fairly well with a dislocation climb mechanism as represented by Eq. [l]. Proceeding as shown previously,1 if creep is controlled by a single climb mechanism, at intermediate stresses, the shear creep rate, y, can be represented by where n and K are material constants {K is independent of the temperature but dependent on the structure, that is, K decreases during the primary stage and reaches a steady-state value over the secondary stage of creep), t is the applied shear stress, G is the shear modulus, gc is the free energy of activation for creep (usually equal to that for self-diffusion, gd), and RT has the usual meaning. By solving for y, the apparent activation energy for creep, Q which can be determined experimentally, is given by where hc is the enthalpy of activation for creep which usually is also equal to that for self-diffusion, h^. By using Eq. [2], the data in Fig. 2 of Ref. 2 can be re-plotted as shown in Fig. 1. By comparing the two figures, it is seen that the slight increase in the apparent activation for creep over Region II, as noted in Fig. 2 of Ref. 2, is due to the influence of temperature on the shear modulus rather than of the stress on the

Jan 1, 1969

By L. Adler

Analysis of a mine roof can be based on fixed-end beam behavior. The author here analyzes the effects of zero restraint at deflecting beam supports. Formulae are given for determining permissible support deflections. Analysis of a mine roof in a bedded deposit usually follows the assumption that the behavior of the roof is analogous to a beam with both ends fixed. Yet it is recognized that the end restraint itself varies with the thickness of cover, so that at shallow depth the restraint is minimum, and at great depth, maximum.' Consequently, an analysis on the basis of fixed ends or full restraint represents only one extreme in the possible range of conditions. Since the actual amount of restraint is difficult to ascertain, a more rational approach is to consider the two extreme cases of end restraint. Such situations regarding uncertainty of the restraining effects of supports are not uncommon in structural analysis, and are handled in a like manner.' Since previous studies9)4 have dealt with full restraint, this paper will analyze the effects of zero restraint at deflecting beam supports. In such a case a mine roof with several intermediate supports becomes analogous to a uniformly loaded continuous beam on simple supports, as shown in Fig. 1A. Such a structure is statically indeterminate to a degree equal to the number of intermediate supports, n. Therefore, with the three equilibrium equations, n additional equations are needed. A number of methods exist to analyze this problem, but The Theorem of Three Moments is Simplest. The continuous beam is divided at each support into a sequence of simply supported single span beams, with the unknown end moments, as appears in Fig. 1B. Continuity requires that the common ends of adjacent beams have the same slope (Fig. 1C). eiB= B(i+l)~= ei(i+l)and MiB= Mti+I)A= Mi(i+i). [1I A Glossary of all terms is given in Table I. Furthermore, if we first consider that the supports do not deflect, the slope at a support is the sum of the slopes due to each of the individual loads shown in Fig. 2, yielding:

Jan 1, 1961

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By Paul Berggreen

LIST OF PUBLICATIONS In the Bibliography titles of publications are replaced by corresponding symbols in this list. American A-1. Transactions of the American Institute of Mining Engineers, New York. A-2. Journal of the New York Microscopical Society, New York. A-3. Journal of the Franklin Institute, Philadelphia, Pa. A-4. The Metallographist, Boston, Mass. A-5. The Electrochemical and Metallurgical Industry, New York. A-6. Bulletin of the American Institute of Mining Engineers, New York. A-7. The Iron Trade Review, Cleveland, Ohio. A-8. The Journal of Physical Chemistry, Ithaca, N. Y. A-9. The Physical Review, New York. A-10. Van Nostrand's Electric Engineering Magazine, New York. English E-1. Proceedings of the Institution of Mechanical Engineers, London. E-2. Journal of the Iron and Steel Institute, London. E3. Proceedings of the Institution of Civil Engineers, London. E-4. Journal of the Chemical Society of London, London. E-5. Philosophical Magazine, London. E-6. Proceedings of the Royal Society of Edinburgh, Edinburgh., E7. Carnegie Scholarship Memoirs, London. E-8. Proceedings of the Royal Society of London, London. E-9. Chemical News, London. E-10. Philosophical Transactions of the Royal Society of London,, London. E-11. Transactions of the North-East Coast Institution of Engineers and Shipbuilders, Newcastle-on-Tyne E-12. Iron, London. E-13. Nature, London. E14. English Mechanic and World of Science, London.

Jan 6, 1914

By Frederick Prime

In this second supplementary list no titles to which an * is pre fixed hare been seen by tlie compiler; and he will be most thankful to have any omiesisne or inaccuracies in the list sent to hiin to be ptiblisi~cd as a third supplement in the next volume of the actiotra. The author is indebted to Prof. J. J. Stevenson, of New Tork, Prof. P. R. Uhlcr and John 'CV. M. Lee, Esq., of Balti more, and Lloyd P. Smith, Esq., of Philadelphia, for valuable assistance. office, allkntorn iron compaxy, 30 South Third Street, Philadelphia, September 5th, 1881. Alabama. Geologiml Survcy of Alabama. report of Progress for 1879 and 1880, by Eugene A. Smith, State Geologist. Montgomery, 1881. 8vo., 158 pp., and 2 maps. California. Omit Report of Hon. T. Butler Ring, iu sopplemeut I. For Trask's Geology and Illdustrial honrecp, etc., in Supplenlvut I., read Tyson's, etc. Fremont's Menloir on Upper Califijrnia, is also published as XXXth Congress, lat Session. Senate Ms. Doc., No 148, and has a map. For Randall's Report in Supplement I, rend Report of the Special Committee in favor of a Geological Snrvey, subrn-itted by Mr. Randall, April 24th, 1861. n.d., 1851. 8cWo., 19 yp. XXXIst Congress, 1st Session, Sen. Ex. Doc., No. 47, Part 2 [Part 1 is Tyson's Report.) RejW of the Secretary of War in further compliance with the Resolution of the Senate?, calling for Colbies of

Jan 1, 1881

"Located on Missouri River 16 miles N. E. from Helena, 67 miles from Butte and 18 miles below Canyon Ferry. River drainage area 16,000 sq. miles.DAM: Built in 1907; rebuilt of concrete in 1911. Maximum height 129.3 ft., length over all 720 ft.; elevation of crest 3621; elevation of bridge 3640; normal head 60'; normal tail water elevation 3568.5.SPILLWAY: Length over all 491 ft.; clear opening in 24 sections; 445' flashboards, 14 high to elevation 3635, which is 3.5' above Canyon Ferry normal tail . water elevation.PENSTOCKS: 5 of steel, 12 ft. diam., about 75 ft. long from canal to main turbines, and 3 40-inch diam. from canal to exciters.WHEELS: 5 main pairs, horizontal, center discharge, 48-inch bronze turbines, 225 rev., 4,000 h-p. at 60 ft. head, made by S. Morgan Smith Co., direct coupled to generators, and--3 single, horizontal, 25-inch units, direct coupled to exciters.GENERATORS: 5 W. E. & M. Co. water wheel type, revolving field, 2,800 k-w., 2,400 v., 225 r. p. m., 3 phase, 60 cycle alternators.OPERATION: The plant has a larger water storage than Canyon Ferry and can also use stored water from Canyon Ferry storage. Separate transmission lines 13 miles long connect to lines from Canyon Ferry to Butte, and the Plant operates in parallel with the Canyon Ferry plant."

Jan 1, 1913

By G. Barbery

Since the original paper, two methods have been introduced to compute the parameters of the three parameter size distribution equation: [ ] Both of them are based on graphical means, which are time-consuming and of little statistical significance. A program has been developed, using the Gauss-Newton method to compute by nonlinear regression analysis the parameters of the equation. Although the method is quite general in curve-fitting applications, it does not appear to be used in the field of size analysis, and a brief description is given. As applied here, the Gauss-Newton method involves the minimization of the least squares: [ ] where n is the number of sieves used. The second member of Eq. 2 can be approximated by a multiple Taylor's series expansion of first order about a starting value [ ] The minimization of Q (r,s,Xo) means: [ ] Putting Eq. 3 into Eq. 2 and differentiating, we obtain a system of equations which can be represented in matrix symbolism (box) The system can be solved for: [ ] and the operations repeated with new values: [ ] The starting values for r and s are taken as 1, for Xo, a value higher than the maximum sieve opening value. Applied to the data given by Herbst 5,6 for batch grinding of 7 X 9 mesh dolomite, the parameters given in Table 1 were obtained. The discussion of the significance of the residual sum of squares is a difficult subject in multiple nonlinear

Jan 1, 1972

By W. J. Babyak, F. N. Rhines

It has long been supposed that, regardless of the mechanism by which grain boundaries increase the hardness of a ductile metal, the effect should be linearly proportional to the grain boundary area. At the present time two methods for determining grain boundary area in an isotropic aggregate are available. The first, derived by Angus and Summers,' presumes that the grain boundary area is equal to 3vn, where n is the number of grains per sq mm in a random section through the metal. This estimate is based upon the assumption that the grains are equivalent to cubes whose faces correspond with the grains as observed in the micro-section. Measurements on copper, bronze, and a brass showed that a nearly linear relation exists between 3vn and hardness. This is illustrated, for the case of brass, in Fig. 1. The second method, developed independently by Smith and Guttman2 and by Duff in, Meussner, and Rhines,3 is absolute and employs a simple linear intercept count for measuring grain boundary area. It involves no assumptions with respect to the shape and distribution of the grain boundaries. The total surface in unit volume is 2 NL , where NL is the number of intercepts between grain boundary and unit length of a test line passed randomly through the sample. In practice, NL,, the average number of grain boundaries intercepted by unit length of traverse across a prepared microsection, is ob-

Jan 1, 1961

WALTER N. CRAFTS,* Toronto, Canada (written discussion?).-During the forging of 9.2-in. shells -for the United States Army, it was noticed that better results were obtained in certain instances when test bars had been held sometime before pulling. An investigation, therefore, was made by our metallographer, Mr. F. M. Arnold, to determine the effect of seasoning. The forging consists of a single operation, piercing a solid cast blank. The test sections were cut from the walls by an oxyacetylene flame, one piece from the nose end and one from the base on the opposite side. The test pieces were not heat treated in any way and the tests and seasonings were carried on at normal atmospheric temperatures. The specifica-tions were as follows: Standard 2-in. test bar, 0.505 in. in diameter; elastic limit, over 19 long tons, or 42,500 lb.; ultimate stress, 39.6 to 49.1 long tons, or 87,500 to 110,000 lb. per sq. in.; elongation, over 13 per cent. As a preliminary test two heats were selected; BP555, which was tested and reported failed on elongation on Aug. 20; and B01771, which was tested and reported failed on Aug. 24. On Aug. 29, retests were cut and machined from the same shells and held till Sept. 3 (5 days) when they were pulled. Both sets of results are given below.

Jan 12, 1919

By AIME

WE got our chance to talk with Arthur J. Blair at the Annual Meeting at the Pennsylvania Hotel. By two o'clock Wednesday afternoon things had quieted down enough so we had our interview in the foyer to the Ball Room. There were the usual questions. Where were you born? In La Salle County, Ill., on March 26, 1885. Where did you go to school? Northwestern University, B.S. degree in 1906. Where did you start work? For E. J. Longyear right after leaving school. One's ability as a geologist was measured by one's ability to wield a brush hook and ax. He stayed on the job as geologist for three years and then got to thinking about the advantages of a warmer climate. The advantages stacked up favorably, so off he went to Birmingham, Ala., just about the time U.S. Steel took over the Tennessee Coal, Iron and Railroad Co.

Jan 1, 1948

PRESIDENT ROBERT E. TALLY, JEROME, ARIZ. PAST PRESIDENTS FREDERICK W. BRADLEY, SAN FRANCISCO, CAL. WILLIAM H. BASSETT, WATERBURY, CONN. TREASURER KARL EILERS, NEW YORK, N. Y.

Jan 1, 1923

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By AIME

After an adventurous past-four changes of government in thirty years -the whole of Silesia and attached coal territories have become part of the Polish State. The coal resources of this area are the biggest among the European countries. Under a surface area of 5700 sq km are about 100 coal seams, with a total thickness of 150 meters. According to German estimates, there are some 150 billion metric tons of coal ranging in thickness up to 14 m within a depth of 1500 m. The seams are mostly level, free from faults, with good top and bottom; the coal is of excellent quality, hard and clean; and mining conditions are favorable. The mines are worked at considerable depth by means of vertical shafts and operate with cage and skip hoisting. Before the war, the mines were up to date, equipped with modern machines. Among the European countries, output per man shift was the highest ? 1.9 to 2.1 metric tons ? and cost of production was the lowest.

Jan 1, 1949

NEW MEMBERS The following list comprises the names of those persons who became. members during the period Sept. 10, 1918, to Oct. 10, 1918. ADDISON, HERBERT, Vice-pres. and Mgr., Big Horn Collieries Co., 412 Colorado Bldg., Denver, Colo. ALLAN, .ANDREW, JR A. Allan & Son, Harrison, N. J. AMI, HENRY M., Charge of War Metals and Minerals, British Embassy, Washington, D. C. ALTHAR, HOMER C., Mill. Engr., The Lorain Coal & Dock Co., Bridgeport, Belmont Co., Ohio. BASER, JOHN T Pres., J. T. Baker Chemical Co., Phillipsburg, N. J. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., 2301 Connecticut Ave., Washington, D. C. BENSON, JOHN PATS Min. Engr., Aurora Cons. Mines Co., Aurora, Nev., BOSWELL, H. F Resident Inspector, Southern Railway System, St. Louis, Mo. BRAUCHER, PETERS., Foundry Mgr., Philadelphia & Reading Ry. Co., Sixth & Perry St., Reading, Pa.

Jan 11, 1918

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By J. R. Dunn

Planning quarry operations and control of the quality of rock materials at Hudson Cement Co. at East Kingston, N. Y., are special problems because of multiple uses for the stone and the great structural complexity of the rocks. Problems have been largely solved by detailed geologic work. These geologic studies have paid dividends in long and short range planning, in assessment of reserves, in vastly reduced cost of chemical analyses, and in reduced drilling costs. Limestones of the Hudson Valley outcrop along the Hudson River from Albany to Kingston. Old established cement companies are located just south of Catskill and just east and southeast of Hudson, N. Y. The new Atlantic Cement plant is being constructed at Ravena. Hudson Cement located at East Kingston, is a newcomer and is closest to the New York metropolitan area (Plate I).

Jan 11, 1961

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By Charles Himrod

IN presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: 1st. Kind of fuel. Bituminous coal not permitting the formation of as much CO2 as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by not allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO,. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a, manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

Jan 1, 1877

By Charles Himrod

In presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO 2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO 2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: lst,. Kind of fuel. Bituminous coal not permitting the formation of as much CO, as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by riot allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO2. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

By Matti J. Saarivirta

Two new precipitation hardening copper-base alloys, Cu-1.5pct Ti-2.5 pct Sn and Cu-1.5 pct Ti-2.5 pct Sn-0.4 pct Cr were developed. High strength and medium conductivity are obtained by solution annealing and subsequent heat treatment. Combination of solution annealing, cold working, and heat treatment increases the strength further. Good elevated temperature strength and ductility makes these alloys superior to copper-beryllium-cobalt alloys. A considerable amount of research work is being done throughout the world to develop new and improved copper-base alloys. In many cases, the object is to develop alloys having a combination of high electrical and thermal conductivities, and high strength. The problem is complicated by the fact that any alloying element added to increase strength, invariably decreases conductivity. Among the few commercial precipitation hardening type copper-base alloys, the Cu-Be-Co alloys are best known. These alloys are used in many applications that require good spring characteristics cornbined with high strength and moderately high electrical conductivity. They can be formed readily after solution annealing, then heat treated to obtain high strength and conductivity. Because of the relatively high cost of the Cu-Be-Co alloys, considerable research has been aimed at developing new lower cost alloys having similar properties. As far as is known today, the binary Cu-Ti alloy is the only one whose properties are

Jan 1, 1962