Search Documents

By W. Rostoker

Single isothermal sections were constructed for the titonium-rich corners of the systems Ti-Fe-O, Ti-Cr-O, and Ti-Ni-0 with a view to locating the shape and disposition of the ternary intermediate-phase fields for the compounds isomorphous with Fe3W3C. IN a previous note,' it was reported that a group of ternary intermediate phases existed which occurred in the general composition range Ti,X,O-Ti&O where X was one of the following elements: copper, nickel, cobalt, iron, or manganese. In two instances, binary intermediate phases occurred (Ti²Cu and Ti²Ni) which appeared to be isomorphous. The X-ray diffraction patterns of the phases could be indexed on a cubic lattice whose cell edge was of the order of 11 kX. Karlsson2 stated that the line extinctions and line intensities indicated that these phases were isomorphous with Fe³W³C and therefore belonged to the space group Oh. This author also noted that no unique phase of this type occurred at the composition Ti,Cr,O. This latter statement was accepted as true at the time the previous technical note was written.' However, work continued along these lines and that reported here has shown that a phase isomorphous with Fe³W³C does exist in the vicinity of the composition Ti³Cr³O but not at or near Ti4 Cr²O. The lattice parameter of this phase was found to be 13.01 kX. Metallographic examination of both as-cast and annealed specimens of these supposed ternary oxide phases disclosed structures which were far from single phase in many instances. It was considered a point of some interest to locate more positively the composition coordinates of the single-phase fields. To this end, single isothermal sections for the systems Ti-Fe-O (1000°C), Ti-Cr-0 (1000°C), and Ti-Ni-0 (900"C) were constructed. Phase relationships were studied by both X-ray diffraction and metallotrra~hic methods. Allovs were prepared as 10 g buttons by melting in a noncon-sumable electrode, water-cooled copper crucible arc-melting furnace using a helium atmosphere. Oxygen was introduced quantitatively by the use of weighed amounts of TiO² or TiO. Iodide titanium and the purest available alloying metals were used. All results are discussed in terms of the nominal composition of the melts. Previous experience with making oxygen-rich alloys had shown that oxygen losses were not significant if a homogeneous melt was produced. Weight-loss measurements were used to check loss in metallics during melting. Anneals were conducted in evacuated Vycor bulbs, and annealing times ranged from 24 hr at 1000 °C to 48 hr at 900°C. To achieve equilibrium in certain sluggish alloys, seven-day anneals were used. Debye-Scherrer powder patterns were taken in a 14 cm diam camera using filtered CuK radiation (K² = 1.541232 kX; K., = 1.53739 kX). Specimens were prepared by crushing and screening previously annealed buttons. In general, the X-ray diffraction results were used to identify the major phases, while the metallographic examinations were more useful in indicating the number of phases present. By the use of the combined results and general fundamental rules governing ternary equilibrium, it was possible to construct isothermal sections in good detail. In some instances where auxiliary lattice-parameter data were available, it was possible to lay down tie lines and to locate more positively corners of three-phase fields. Isothermal Section of the System Ti-Fe-O at 1000°C The binary systems Ti-O³ and Ti-Fe4 have been published. Binary phases, TiO, TiFe, and TiFe2, are likely to be encountered in the titanium-rich corner of the system. The structures are NaCl (Bl), CsCl (B2), and MgZn, (C14) types, respectively. Although preliminary X-ray diffraction studies indicated the presence of a ternary phase in the composition range Ti,Fe,O-TiJ?e,O, metallographic examination of two specimens at these compositions revealed the presence of other phases. Thirty-eight alloys were used to delineate the phase boundaries of the isothermal section illustrated in Fig. 1. The five almost single-phase ter-

Jan 1, 1956

By D. R. Bomberger, M. Deul

An automatic microscope has been developed to measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed. In the study of coal cleaning by pseudo-gravity methods (tables, cyclones, hydrotators, etc.), it is customary to express the deficiency of the process relative to float-sink measurements in some form of "percent efficiency". These have been calculated in many different ways in order to provide a means of extrapolation of test data to untested coal feeds. This works quite well with coarse coal (here defined as larger than one-eighth in.). Large, heavy pieces of refuse are rejected rather thoroughly by many cleaning processes, and the efficiencies relative to float-sink results approach 100%. In coarse coals, the difference in the sizes of fine pyrite is masked by the averaging effect of the large coal envelopes. The existence and fate of fine pyrite is often hidden in the larger numbers representing coarse (and easily removed) pyrite. There are cases where it is desirable to subject fine coal (here defined as smaller than one-eighth in.) to cleaning processes. This is true of naturally occurring fie coal streams and in cases where comminution followed by cleaning is necessary to provide the quality desired. It is in this area that the use of process efficiency relative to float sink fails. Percent efficiencies decline to very low figures, and equivalent separation densities become a matter for conjecture. The net result is that an attempt to estimate product quality from float-sink data and a process efficiency figure often results in large errors. This work represents a new approach to the problem by observing the fate of pyrite particles, grouped by sizes, in a cleaning process. Examples are given which relate pyrite size measurements to float-sink washability and to a Deister Table operation. EXPERIMENTAL WORK The automatic microscope used here has been previously described.' Briefly, it is an instrument which measures the diam of particles (as defined by a range of reflectance) exposed on a polished specimen. The instrument scans a sample briquet, measures diam of exposed pyrite inclusions and records the data by size intervals. Preparation of the briquet is critical, due to the automatic nature of the process. The principal requirement is for an optically flat surface, so that focus will be maintained as the motorized stage moves the specimen under the lens. The various substances present must be polished to the same level in spite of the wide difference in hardness between coal substance and minerals. The polishing method must not pluck out small grains, which might be rather loosely held by surrounding coal. The procedure below was successful in producing all of these results. The coal sample (8 mesh or finer) was riffled (a micro vibrating riffle is essential) to obtain 15 g. One volume of Lucite powder (thermosetting plastic mounting medium) was mixed with three volumes of coal and mixed thoroughly. A briquet was formed using a cylindrical die (1 1/4 in. diam) at 3000 lb per in.* pressure and 150°C. Preparation of the optical surface was accomplished on automatic polishing equipment, according to the following schedule: 1) Grinding: 3 stages, using successively fine Carborundum grits of 180, 320 and 600 mesh. 2) Rough polishing: 2 stages, using 3µ alumina on cast iron, followed by 1µ alumina on lead. 3) Fine polishing: 2 stages, using 0.5µ alumina on napless broadcloth over bronze, followed by 0.1µ alumina on silk filament cloth over bronze. Raw data were corrected for the fact that the chords

Jan 1, 1964

By R. L. Perrine

A stability theory is developed for miscible liquid-liquid displacement within a porous medium. In the usual case considered, a high-density high-viscosity "oil" is displaced downdip by a low-density low-viscosity "solvent'! Perturbation methods are used to find the conditions under which the spreading mechanism changes from the stable dispersion process to unstable viscous fingering. We find that instability is conditional, that there is a dependence on the shape of a disturbance leading to a"diameter" effect and that very difficult experimental scaling problems may result. A useful consequence is the definition of a minimum "slug size" for stable miscible displacement. This should make possible optimum use of the solvent process for oil recovery. The results may apply to many situations in which one fluid displaces another of somewhat different fluid properties within a porous medium. INTRODUCTION The process of miscible liquid-liquid displacement looked very favorable when it first received serious consideration as a means to increase petroleum recovery. Some early laboratory results were interpreted to mean that only a small "slug" of solvent was needed, perhaps 2 to 3 per cent of a hydrocarbon pore volume. This "slug" could recover the oil in an entire reservoir provided the fluids remained miscible.1,2 Only a slow growth of the "mixing zone", or gradual transition from oil to solvent, should occur. This would follow naturally from mixing by a dispersion mechanism such as that described by Scheidegger.3 And, indeed, laboratory cores have shown this kind of behavior provided solvent viscosity was at least as great as that of the oi1.2,4-6 The same kind of behavior has also been observed with solvent viscosity lower than that of the oil after the distance traversed became large. Not all laboratory results have been this favorable, however.7-9 Mixing zone growth may become proportional to the distance traveled rather than the square root of this quantity. Such behavior accompanies high rates in short systems of large diameter, provided the viscosity ratio is adverse. If this more rapid spreading were to persist in a reservoir, the solvent requirement for miscible "slug" displacement could exceed 30 per cent of a pore volume. There is considerable economic importance in the difference between 3 and 30 per cent solvent. A 1ogical conclusion is that two different kinds of flow behavior are possible, with each kind leading to a different result. One kind gives efficient displacement, the other does not. In the efficient case, the solvent bank spreads out only by the mechanism we have termed dispersion. Under these conditions, displacement is as near piston-like as possible. In the second kind of flow, found only with adverse viscosity ratios, viscous fingering occurs. That is, permeability variations cause a small finger of low-viscosity solvent-rich fluid to move ahead of its average position within the mixing zone. This creates a path of low resistance to flow, and an even greater amount of solvent-rich fluid follows. Thus, the process is autocatalytic. Once started, the fingering mechanism rapidly becomes dominant. The question to be answered is this. Under what conditions will each of these two different kinds of flow occur? In particular, what conditions denote the transition from dispersion to viscous fingering as the solvent spreading mechanism? The answer may tell us whether or not the desirable, near piston-like miscible displacement process is practical. An answer to this problem can be obtained from theory by the use of perturbation methods. The procedure is as follows. We first formulate a mathematical representation of the system. Then a small disturbance (or perturbation) in solvent concentration profile is introduced and observed to see what happens. Unstable flow is indicated when a small disturbance will grow larger. This will lead to eventual viscous fingering. If on the other hand the disturbance dies out, the displacement is stable. In this latter case, with dispersion as the spreading mechanism, near piston-like displacement is possible. Thus, this paper presents the development of a stability theory for miscible liquid-liquid displace-

By P. R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,' and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.'.' Bunker Hill Co. of Kellogg, Idaho, supplied the ore sample used in these tests. The sample was typical of the ore milled in 1949 and contained 4.52 pct Pb and 1.08 pct Zn. A flotation test made by the author with potassium ethyl xanthate as a collector, the same flotation reagents, and the same grind employed in regular Bunker Hill mill practice was the standard for comparing results with the compounds and derivatives of guanidine. The compounds and derivatives of guanidine are only fair collectors of galena. However, if potassium ethyl xanthate were used in the galena float, its presence later in the sphalerite float would make it impossible to introduce another type of collector and be certain which collector contributed the result, so the compound or derivative of guanidine under test was used in both the galena and sphalerite floats in Table I. On both the galena and the sphalerite in the Bunker Hill ore, the depressing action of sodium cyanide and zinc sulfate is much greater with collectors of the guanidine type than with the xanthates. If the depressing agents are left out when a guanidine type of collector is used, but a pH of 8.6 is maintained with either lime or sodium carbonate, the depressing action is approximately the same as in the standard xanthate test. Consequently the depressing agents, sodium cyanide and zinc, were not used in the galena floats of tests 1226, 1228, and 1286, Table I, so the galena floats would be on a comparable basis with the standard xanthate test. As shown by the tests in Table I, the loss in the tail when diphenyl guanidine is used is 8.3 to 9.3 pct, as compared to 17.6 pct with potassium ethyl xanthate, or a recovery of 2.3 to 2.0 lb more zinc. Concentrate grade is 13.7 pct with potassium ethyl xanthate and increases to 22.9 and 31.8 pct with diphenyl guanidine, showing a much higher selectivity. Unless the Barrett's No. 4 coal tar creosote is considered to be a collector, no collector other than diphenyl guanidine is present in the tests, Nos. 1226, 1228, and 1286. Tests 1218, 1253, and 1263 in Table I1 were run to check the effect of the depressing agents used in flotation of the galena (sodium cyanide and zinc sulfate) upon subsequent flotation of sphalerite by diphenyl guanidine. Urea was substituted for potassium ethyl xanthate in tests 1253 and 1263 because it is a good collector for galena and a poor one for sphalerite, and the effect of the depressing agents is more marked with urea than with potassium ethyl xanthate. Test 1205 checks the effect of urea alone without any depressing agents when used for the flotation of galena. Table I1 shows that diphenyl guanidine as a collector for sphalerite is compatible with other flotation reagents used in floating galena. When the depressing agents sodium cyanide and zinc sulfate are used in the galena flotation step, the amount of lime in the sphalerite flotation must be increased (compare 1253 and 1263). Table I11 gives some of the compounds of guanidine which were tested and compared. Some of the compounds and derivatives of guanidine* are solu- * Diphenyl guanidine is in commercial production and is available on the market. ble in water and others are not. Those tested were fed dry. When an organic collector is promising, its compounds and derivatives should be tested and their comparative collecting power recorded. Eventually, in this way, it may be possible to discover some of the essential chemical characteristics of a good collector. For example, it is interesting to compare the diphenyl and dibutyl derivatives in Table IV with those of urea in Table 111, Example 3, U. S. Patent 2,664,198. All are good collectors. Table I shows some of the effects of lime on recovery of sphalerite by diphenyl guanidine. Table V

Jan 1, 1960

By E. T. Turkdogan, L. E. Leake

A number of measurements have been made on the vapor pressure of pure iron at 1600°C. Experiments were carried out by the transportation method in which a sample of iron is exposed in a furnace to a stream of pure argon, metered at a predetermined flow rate for a specified period of time. The vapor pressure was obtained from the weight loss of the sample. A detailed diagram of the apparatus used for the experiments is given in Fig. 1. It consisted of a horizontal molybdenum-wire-wound furnace fitted with a recrystallized alumina tube 1 1/8 in. internal diam. The boats, 1 by 3/16 by 1/8 in., were fired in argon at 1600°C to constant weight before use. After this treatment, subsequent heating of the boats to 1600°C gave little or no further change in weight, e.g. ±0.05 mg in 24 hr. The furnace and reaction tube were separately fed with argon from two independent flowmeters. These were connected to a common supply source via an argon purification furnace containing metallic titanium sponge at 700°C, and an anhydrone drying-tower. A rotary displacement-type meter was included in the gas train to provide a direct means of measuring the total volume of gas passed through the reaction tube. The material used was vacuum melted high-purity iron in the form of wire 2mm in diam. The following impurities were present in the iron: 0.008 pct C, 0.002 pct Si, 0.005 pct Mn, 0.008 pct S, 0.001 pct P, 0.01 pct Ni, 0.001 pct Cr, 0.006 pct Cu, and 0.001 pct Al. Samples consisting of three small pieces of this wire were laid end to end in a recrystallized alumina-combustion boat, and were separated by small fragments of alumina. The wire samples were then melted in argon to form spherical beads 2 to 3 mm in diam. After weighing, the boat with its contents was placed on the boat carrier and introduced into the cool end of the reaction tube. The entire furnace system was then flushed with argon for 30 min. At the end of this period, the flow of argon to both furnace and reaction tubes was adjusted to the desired level; then the boat was slid rapidly into the hot-zone of the reaction tube. After a known volume of gas had passed through the reaction tube, the boat was withdrawn quickly to the cool end of the furnace. When quite cool, the boat was removed from the fur-mace and placed in a desiccator for subsequent re-weighing. The semi-micro balance used in these experiments had a sensitivity of 0.005 mg. The above procedure was repeated at several flow rates within the range of 25 to 300 ml per min. The flow of argon in the annular space between the two tubes was at a rate of 300 ml per min in all experiments. During all the experiments the furnace temperature was maintained at 1600° ± 5°C by means of a temperature controller. The temperature of the reaction zone was measured with a Tinsley high precision disappearing filament pyrometer which was initially calibrated against a Pt-13 pct Rh/Pt thermocouple; the errors due to temperature measurements were within * 5°C. RESULTS Assuming that the iron vapor is in the monatomic state, the vapor pressure can be calculated from the weight loss of the sample and the volume of the carrier gas. The results obtained are plotted in Fig. 2 against the rate of flow of argon through the chamber containing liquid iron beads. At low flow rates, the thermal diffusion of iron gives an apparent high vapor pressure, but at high gas flow rates, the carrier gas is not saturated with the vapor, and therefore, low vapor-pressure values are obtained. This is now a well-known phenomenon. There is a distinct inflexion of the curve at about 120 to 160 ml per min rate of argon flow and the vapor pressure of iron within this

Jan 1, 1961

By John E. Willson, Ben L. Seegmiller

A portable electronic instrument was designed and constructed to detect unknown stress magnitudes in rocks. The principle used to detect stress is based on the propagation velocity method. This method allows the stress in a rock subjected to a load of unknown magnitude to be determined, provided that the wave velocity-stress relationship for similar rock is known. This is accomplished by measuring the travel time of longitudinal mechanical waves passing between two points a set distance apart in a rock. The velocity of the wave is calculated and the stress determined from the wave velocity-stress relationship. If the sending and receiving transducer spacing is constant, a time vs. stress relationship rather than the velocity-stress relationship may be used. The method is nondestructive and tests can be made without drilling or otherwise disturbing the rocks. The first studies undertaken in the United States to determine stress in rocks using propagation velocity techniques were reported by Obert1,2 in 1939 and 1940. The Soviet Union first reported using propagation methods to study rock pressures in 1951.8 Success of the method led to the development of a pulse-type ultrasonic seismoscope4 in 1953. Using this instrument, Ivanov and Betaneli5,6 in 1963 succeeded in devising and testing under field conditions a method of investigating coal pillar stresses. In 1967 Osipova7 reported results of similar studies in the Nakhichevan salt mines. In France, Tincelin8 has used the propagation velocity method to study the stress distribution in iron ore pillars. Uhlmann9 has investigated stresses in salt and potash pillars in Germany, using velocity techniques. Determination of uniaxial stress by propagation velocity methods is limited to rocks which have readily detectable wave velocity-stress variations. The present stress detection instrument is restricted in application to rocks which have a velocity change under stress of at least 300 fps. Examples of rocks which meet this requirement are sandstones, coal, and possibly some limestones. Testing of this instrument was limited to a laboratory study and the results may or may not be indicative of what would be found in a field test. A program of field experiments to study the feasibility of using this instrument to determine mine pillar and tunnel stresses is in progress. Instrument Design The instrument has two main components: A probe and a control-display unit. The probe is a hand-held device to which two identical rodlike transducers are rigidly mounted. Coaxial cable connects the probe to the control-display unit which is mounted in an enclosed carrying case measuring 7 % x 9 x 13 in. The instrument is designed so it may be carried and operated by one man. Weight of the probe and enclosed control-display unit is approximately 20.1b. The probe consists of two transducers identical in construction. One transducer is used to convert electronic pulses to mechanical waves and transmit these waves into a rock. The other detects the transmitted waves in the rock and converts them back into electronic signals. The basic element in both transducers is a piezoelectric crystal. The crystal is a disk made of lead titanate zirconate and has a natural resonant frequency of 400 kHz ±1% in the thickness mode. A schematic of one of the two identical transducing elements is shown in [Fig. 1.] A spacing of 6 in. between sending and receiving transducers has been found to be most satisfactory. The control-display unit consists of a pulse generator and a 1-in. oscilloscope. Various electronic devices are used for the power supply, amplification, and calibration. The amplitude of the square wave from the pulse generator can be continuously varied between 0 and +20 vdc. Pulse width can be set at 1, 2, 3, or 4 µsec. The repetition rate of the pulse can have the following values: 50, 75, 100, 150, 200, 250, 300, 400, 500, 750, and 1000 Hz. The oscilloscope delay system allows the travel time of the longitudinal wave passing through a rock to be measured to an accuracy ±0.1 µsec in the range from 0 to 995 µsec. Fig. 2 is a schematic of the various electronic sections in the control-display unit. Laboratory Testing The first step in using the instrument is to develop a velocity-stress or a time-stress curve for the par-

Jan 1, 1972

By H. Sigurdson, T. V. Cherian, C. H. Moore

The phenomenon of recovery of cold-worked metals is interesting not only because of its practical importance but also because of its fundamental significance in solid state reactions. Although extensive investigations1,2 have already been made in an attempt to discover the mechanics of the recovery process, many of the observations have not yet been satisfactorily correlated to provide a completely consistent model for the process. The wide differences in the recovery rates of various properties can be cited as a typical example of one of the difficulties that are encountered. Frequently, for example, the electrical resistance will have almost completely recovered before any recovery in tensile strength can be detected. Of course, such differences in the recovery rates of different properties might be explained by assuming that each property is a unique function of the work-hardened state, and consequently each property exhibits its own unique recovery rate. The assumption that different properties are uniquely related to the work-hardened state cannot be denied. On the other hand, the properties that recover at different rates often exhibit more or less parallel changes upon work-hardening. This suggests that the microstructural changes attending recovery are not exactly the reverse of the changes attending work-hardening. Several types of imperfections must be postulated in order to account for this apparent anomaly. The different recovery rates for various properties, then, are due to the different recovery rales of the type of imperfection to which each property is most sensitive as well as the unique dependence of each property on the cold- worked state. This concept assumes that a simple model of the work-hardened state consisting only of one type of imperfection, such as Taylor's type of dislocation patterns, is inadequate to cope with the diversified phenomena attending work-hardening and recovery. Although current models for the work-hardened state are not useful for describing all aspects of the recovery process, the general trends of the recovery of each postulated type of imperfection as a function of time and temperature should be at least qualitatively deducible from the rather well developed laws of kinetics of reactions in the solid state. Consequently, recovery data might prove useful for elucidating some aspects of the complexities of the work-hardened state of metals. A preliminary attempt to study work-hardening by investigating recovery rates of cold-worked metals is outlined in the following pages of this report. Experimental Procedure Many properties recover when cold-worked metals are annealed below their recrystallization temperature. Therefore, electrical resistivity, thermal electromotive force, X ray diffraction line widths, X ray diffraction line intensities, elastic spring back, density and other physical and chemical properties have been used to study the recovery process. Major interest, however, has generally been directed toward the recovery of the mechanical properties such as hardness, yield strength, and tensile strength. But a search of the literature suggests that the effect of recovery on the true stress-true strain curve has been neglected, in spite of the current recognition of the fundamental importance of such an investigation. An investigation on the effect of recovery treatment on the true stress-true strain curves in tension, therefore, was undertaken in the present study. Commercially pure aluminum (99. + pet Al) in the form of 0.100 in. thick rolled sheet of 2S-O aluminum alloy was selected as the material for this investigation because rather extensive correlatable data are already available on the recovery of some of its properties. Tensile specimens having a 6 in. long gauge section and a uniform reduced section width of 0.500 in. were machined from the sheet in accordance with a design that has previously been reported.3 All specimens were selected with their axes aligned in the rolling direction. In order to eliminate the effects of previous work-hardening and the effects of machining, the specimens were annealed for 15 min. at 750°F before testing. During tensile testing the loads were measured by means of a proving ring (sensitive to 1/2 lb) in series with the specimen.4 Strains were determined from the extension of a rack and pinion strain gauge sensitive to a strain of + 0.0001. The stress was recorded as the true stress, namely

Jan 1, 1950

By A. H. Larson, R. J. McClincy

The activity of Sb,03 in PbO-Sb,03 slags containing less than 50 mol pct Sb,03 was determined by the inert-gas saturation method at 700°C. In this composition range, the activity gf SbzO3 shows a strong negative deviation from ideality. The activity of PbO in these slags was calculated by application of the Gibbs-Duhem iniegration to the Sb203 activity data. The calculated activity of PbO in slags containing more than 63 mol pct PbO was found to deviate in a positive direction from ideality uthile a negative deviation was found for slags containing less PbO. The standard Gibbs free energies of formation of Sb,03 and PbO. Sb203 have been calculated and compared with existing data in the literature. The activity of Sb203 in PbO-Si0,-Sb203 (PbO/SiO, = 2) slags containing less than 25 mol pct Sb,03 was also determined by the inert-gas saturation method at 700°C. In this composition range, the activity of Sbz03 shows a very large negative deviation from ideality. VERY little experimental work has been published in the past to determine equilibrium data in the oxide systems connected with the refining of lead. These data are of value since impurities such as antimony, arsenic, and tin must be removed from lead and recovered for further treatment. Equilibrium studies on antimony and arsenic systems are also of interest for the design of new processes for lead refining and lead dross treatment. Maier and ~incke' first determined the liquidus curves for the PbO-Sb203 system and identified the compound PbO . Sb203. They found the phase diagram for this system to be two simple eutectics located on either side of the congruent melting compound. They also determined a very limited amount of vapor pressure data for Sb406 abbve PbO-Sba3 melts at 697"~. A second phase diagram investigation on this system was reported by Hennig and Kohlmeyer' who confirmed the existence of the compound PbO . Sb203 as well as the form of the diagram. A disagreement was noticed, however, in that their liquidus temperatures over nearly the entire composition range were higher than those reported by Maier and Hincke. Barthel~ and pelze14 redetermined the liquidus curve at the PbO-rich end of the PbO-Sb@, system and agreed very closely with the results of Maier and Hincke. None of the investigators mentioned above reported any mutual solid solubility in the PbO-SbD3 system. Zunkel and Larson5 have determined the phase diagram for the PbO-rich end of the PbO-Sb203 system by slag-metal equilibrium studies in the Pb-PbO-Sb203 system and by thermal analysis studies in the PbO-Sbz03 system. A maximum solid solubility of 5.6 mol pct Sb203 in PbO was observed at the eutectic temperature of 604°C. Their results for the phase diagram agree favorably with those of Maier and Hincke. The vapor pressure of Sb2O3 in the temperature range from 470" to 800°C has been determined by Hincke, using a modification of the transportation meth~d.~ His results for temperatures below the melting point of Sba3 are the only data reported in the published literature. The predominant vapor species has been shown to be Sb,06 by Norman and staley.? Myzenkov and Klushin,8 using the boiling-point method, have determined the pressure of Sb406 above liquid SbD3 in the temperature range from 715" to 1025°C. The agreement between these two studies is not very close. A portion of the discrepancy lies in the fact that Hincke used silica crucibles, which were attacked by the liquid Sbz03 at high temperatures. This fact does not account, however. for the large difference observed at the melting point. ~aier' gives a brief summary of vapor pressure data for Sb,O, above pure liquid Sbz03 which agree quite well with the data of Myzenkov and Klushin at temperatures near the melting point. This paper describes the determination of Sb2O3 activity data in the PbO-Sb203 and Pb0-Si02-Sb203 (PbO/SiOz = 2) systems by the inert-gas saturation method. These activity data are compared with the data calculated by Zunkel and arson. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade PbO (99.8 pct PbO, 0.14 pct insoluble in CHsCOOH, 0.02 pct not precipitated by HB, 0.1 pct CaO, and 0.08 pct SiOz), Sbf13 (99.6 pct Sb203, 0.004 PC~ C1-, 0.005 PC~ SO;-, 0.15 p~t AS, 0.001 pct Fe, and 0.03 pct other heavy metals such as Pb), and SiOz (chromatographic grade). Apparatus for Vapor Pressure Determinations. The apparatus used in this investigation consisted of a transportation reaction system with two separate gas trains. The argon transporting gas was first mixed with a small amount of hydrogen, metered, and dried by passage through silica gel and anhydrone drying tubes arranged in series. After this preliminary drying, the argon was passed through copper wool at 500°C to convert the residual oxygen to water vapor which was removed by three anhydrone drying tubes. A second stream of argon was metered and dried and then passed around the outside of the alumina reaction tube to flush away the volatile species to pre-

Jan 1, 1970

By L. C. Brown, C. St. John, C. C. Sanderson

The diffusion rate in Cu-Te couples is very sensitive to compressive stress, with a load of 20 psi making a significant difference to the width of the diffusion zone. At zero stress, two phases appear in the diffusion zone (Cu4Te3 and CuTe). Under compressive loading the third stable phase (Cuz Te) also appears, and its thickness increases progressively with increasing stress. The results are explained on the basis of an incipient Kirkendall porosity which restricts the transfer of atoms from the copper into the diffusion zone. DURING a study of the Kirkendall effect in Cu-Te couples prepared by clamping together the two components, it was found that the diffusion-zone width and shape in the plane of contact were not reproducible. Although the stresses involved in clamping are not normally sufficiently high to affect diffusion rates, preliminary tests established that the Cu-Te system is particularly stress-sensitive. The phase diagram for the system Cu-Te given in Hanssen1 shows that there is practically no solid solubility at either end of the phase diagram. Many areas of the diagram are not fully substantiated, but there appear to be three intermediate phases: Cu,Te—hexagonal in structure, having a grey luster; Cu4Te3—a tetragonal defect structure, having a red-purple luster; CuTe—orthorhombic in structure and having a golden-green luster. The existence of a fourth phase, the X phase at 37 at. pct Te, is considered doubtful. The composition ranges of the three stable phases are small, and are not accurately known. The phase diagram changes little with temperature up to 305°C, at which temperature a polymorphic transformation takes place in Cu2Te. The nature of the Cu-Te phase diagram indicates that the diffusion zone in a Cu-Te couple would consist of a series of layers of intermediate phases. The relative thickness of any one phase will depend on its diffusion coefficient and composition range.' In this type of diffusion couple it is often found experimentally that some phases are not visible at all in the diffusion zone due either to a small diffusion coefficient or to a restricted composition range.3 Since the composition ranges of the phases in Cu-Te are not known, it is not possible to determine diffusion coefficients in this system from a knowledge of the phase thicknesses. Several investigations have been carried out to determine the effect of compressive stress on diffusion rates in multiphase systems. Diffusion couples of Ni-A1 have been investigated by Storchheim et al.4 and by Castleman and Seigle.5 Two phases (ß and ?) appear in the diffusion zone under zero stress and the thickness of both phases is progressively reduced with increasing stress. According to Storchheim et al.4 a stress of 25,000 psi reduces the thickness of the diffusion zone by 50 pct. In a-brass—?-brass couples the thickness of the 0 phase formed in the diffusion zone was reduced by 20 pct at a stress of 20,000 psi.6 In other investigations the compressive load has been observed to increase the width of the diffusion zone. In A1-U, several investigators3,8 have found the width of the whase UA13 to increase with stress. According to casileman,8 the rate of formation of UA13 at 520°C is 75 pct faster at a stress of 20,000 psi as compared with a stress of 2500 psi. In Cu-Sb the effect of stress is greater than in the other systems described. According to Heumann9,10 only one phase (y) appears in the diffusion zone at a stress of 500 psi, but at a stress of 850 psi two phases (y and k) are present. If a diffusion couple containing both y and k phases is annealed at a low stress level, the y phase grows at the expense of the k phase. EXPERIMENTAL The diffusion couples were prepared from electrolytic copper bar stock with a nominal purity of 99.92 pct and from tellurium of 99.7 pct purity. The tellurium proved difficult to machine because of its brittleness and a technique was developed for casting the tellurium into a graphite slab mold and spark-machining specimens from this slab. Both the copper and tellurium were produced in the form of discs 2 in. diam by approximately 1/4 in. thick with surfaces ground flat to 3/0 emery paper. The diffusion apparatus is shown in Fig. 1. Auni-axial compressive stress was applied to the system through a simple lever system. A stainless-steel rod actuated by the lever arm lay inside a stainless-steel tube. The diffusion couple lay on top of the steel rod, and pressure was applied to the couple between the rod and a plug welded into the center of the tube. To ensure a uniform stress across the couple, a hemispherical boss and cup were used to transmit the load to the diffusion couple. A 400-w tube furnace with a uniform hot zone 3 in. long slid around the stainless-steel tube and maintained the assembly at temperature. A thermocouple situated 3 in. from the specimen operated a proportional temperature controller which maintained the specimen temperature constant to ±2°C. Most diffusion runs were carried out at 250C although a few tests were made at other temperatures in the range 235° to 300°C. The specimens were inserted and removed with the furnace at operating temperature, and took only 2 min to reach diffusion temperature—a time small compared with the total diffusion time. All the diffusion experiments were carried out in a hydrogen atmosphere, since consistent results were obtained in hydrogen and nitrogen atmospheres and in

Jan 1, 1967

By David L. Holt

The contribution of grain boundary shear to total elongation, CS/E&apos;, has been measured in an Al-Zn eu-tectoid alloy that was quenched from above the invariant temperature, then annealed at 250° C to a grain size of&apos; 1.8 p. At 250°C, ks/E&apos; is low at both high and low strain rates, but reaches a maximum, estimated as 60 pct at an intermediate rate of 5 X 10 per rnin. Rate sensitivity, as measured by the index m = a log a/a log E&apos;, follows the same trend, and furthermore the maximum values of m and -cur at approximately the same strain rate. This result, combined with the metallographic observation that boundary migration enhances boundary shearing, is interpreted as supporting a previous suggestion that the high rate sensitivity characterizing super-plasticity is the result of combined boundary shearing and migration. It is suggested that the latter event relieves stress concentrations at triple points, and smoothes boundaries so that stress is governed largely by a viscous boundary shear. GrAIN boundary shear has been considered in relation to superplasticity in several recent papers.&apos; The problem has been to explain the high strain rate sensitivity of flow stress, and the variation of rate sensitivity with strain rate (E&apos;) and grain size (L). The requirements for superplasticity, small L and high T, suggest the reasonableness of an approach to high rate sensitivity involving grain boundary shear. Further support came from experiments on the A1-Cu eutectic alloy,&apos; where it was found that strain rate sensitivity of cast material annealed to produce an equiaxed, micron-size grain is always low; taking as an index of rate sensitivity m = a log a/a log <, m < 0.3. However, m in hot-worked alloy of comparable grain size can be as high as 0.7. In the cast and annealed material, each phase is a single crystal, the only boundaries are interphase boundaries, and it is, consequently, geometrically impossible for boundary shear to contribute to deformation in any major way. Other observations (for hot-worked material) were a-L at constant (low) strain rates and indications that the rate of recrystallization was enhanced as strain rate increased. As a result of this work, it was proposed that high rate sensitivity arises from a deformation mode of boundary shear associated with boundary migration. Migration serves to relieve stress concentrations at triple points, and smoothes boundaries so that they assume properties of fluid films. On the other hand, the low rate sensitivity observed at high and low strain rates reflects deformation of bulk material. Measurement of the variation of grain boundary shear with strain rate and m have not yet been made. Such measurements are important, especially in view of a proposal, differing in detail from the above, that high m arises merely from a transition between a grain boundary shear mode of deformation at low rates to a transgranular mode at high rates.2&apos;4 In the present work, the contribution of boundary shear to total deformation is measured and in addition metallographic observations are made on surfaces of deformed specimens to look at the interaction between boundary shear and migration. The Al-Zn eutectoid alloy was chosen for its homogeneous, fine-grained structure, which is obtained readily without hot-working. It has also been the subject of a previous phenom-enologically directed study. EXPERIMENTAL Material. Compression specimens, cross section 4 by + in., length \ in., were machined from a sand-cast ingot of composition 77.5 wt pct Zn, 22.5 wt pct Al. (The melt was prepared from 99.9 pct Zn and 99.99 pct Al.) After homogenization at 375°C for 50 hr, the specimens were quenched in brine and removed before the heat evolution that accompanies de -composition of the high-temperature phase.5&apos;6 The resulting microstructure, see Fig. l(a), was too fine for grain boundary sliding to be easily studied; coarser structures were obtained by annealing for various times at 2 50°C. Annealing was terminated by a brine quench. Final average intercept lengths between all grain boundaries (both interphase and those lying in a phase), L, were: 0.5 p [annealed for 15 min, Fig. (a)], 0.8, 1.1, and 1.8 p [Fig. l(b)l. Testing Procedure. An Instron machine was used for most of the compressive deformation. Tests were of two types: those in which crosshead velocity was changed in steps to measure m as a function of strain rate15 and tests at constant velocity to a fixed (engineering) strain of -0.2 (20 pct). Stress reached a steady-state value (a) which was plotted, on a logarithmic scale, against log strain rate (E&apos;). An alternate and equivalent evaluation of m was to take the slope of the log o vs log 6 curve. Time at temperature before testing was 15 min. Strain rates covered by the Instron (4 x lo-&apos; to 4 x 10&apos; per min) were insufficient; at a higher rate of 5 x lo2 per min a gas-operated testing machine was used, the gas driving a piston to compress the specimen at a controlled velocity.&apos; To obtain points on the log a vs log E&apos; curve at low rates, specimens were compressed by a dead weight. strain rate was an average value computed by dividing strain at the end of test by loading time. In some tests strain was measured at fractions of the loading time; creep rate was found to be reasonably constant.

Jan 1, 1969

By M. C. Udy, F. W. Boulger

AN incomplete phase diagram for the U-Ti systern was determined earlier 1 and more recently, a tentative diagram was presented for the uranium-rich end of the system.&apos; In the present re-examination of the whole system of U-Ti alloys, high purity materials were used. Melting stock for the alloys was high purity uranium, containing about 0.09 pct C as the only appreciable impurity, and high purity iodide-process titanium purchased from New Jersey Zinc Co. Both metals were cold rolled to about 1/6 in. thickness, sheared to about I/&apos; in. squares, and cleaned by pickling. The alloys were arc melted under a helium atmosphere in a water-cooled copper crucible. A thoriated-tungsten electrode was used. The furnace chamber was evacuated, then flushed with helium, prior to each melting. It was finally filled with stagnant helium at one atmosphere pressure. Each alloy was remelted three times after the original melting, to insure homogeneity. The alloy button was turned bottom side up before each re-melting operation. Some 22 alloys were examined. Their compositions were spaced at appropriate intervals between 100 pct Ti and 100 pct U. Analyses were made on chips taken after fabrication. The major contaminant was carbon, which varied from 0.03 to 0.08 pct. It appeared in the microstructure as titanium carbide. Alloy compositions were calculated to a carbon-free basis for consideration on the diagram. Tungsten and copper, possible contaminants from the melting operation, were generally less than 100 parts per million each. Fabrication All alloys were forged and rolled to bars approximately V8 in. square. They were clad either in SAE 1020 steel or in a 5 pct Cr-3 pct Al-Ti-base alloy, depending on the fabrication temperature. A temperature of 1800°F (980°C) was used for alloys near the compound composition. This necessitated using the titanium-base alloy, since iron reacts with titanium at this temperature, producing a low melting alloy. Other alloys were fabricated at 1450°F (790°C), using steel jackets. No iron-titanium reaction occurred at this temperature. The jackets were welded in place in an argon atmosphere. Those alloys sheathed in steel were declad and then reclad between rolling and forging operations. On the other hand, those clad with the titanium alloy were cut to a roughly rectangular shape prior to clading and were then carried through both the forging and rolling operations without opening. Those alloys near the compound composition were found to be cracked when the clading was removed. The cracked materials had been plastically deformed, however, and at least some of the cracking had OCcurred during cooling. Heat Treatment The rolled bars, after being declad and shaped to remove surface contamination, were all given an homogenizing treatment of 160 hr at 2000°F. (Samples were taken for analysis following the declading and shaping operations.) All were heat treated at the same time in one furnace, but each was sealed in a purified argon atmosphere in an individual Vycor glass tube. Argon pressure was such that it was approximately atmospheric at temperature. One end of each tube contained titanium chips and this end was heated to 1200°F (650°C) for 10 min prior to the heat treatment. This purged the atmosphere of residual reactive gases. The balance of the tube was warmed during the purge to liberate adsorbed moisture and gases, which also reacted with the hot chips. The bars were furnace cooled from the homogenization treatment. Specimens of each alloy were water quenched after 2 hr heating at 1000°, 1200°, 1400°, 1600°, 1800°, and 2000°F (540°, 650°, 760°, 870°, 980°, and 1095°C). In addition, some were treated at intermediate temperatures of 1300°, 1500°, and 1700°F (705", 815", and 925°C) and at 2150°F (1175°C). Specimens, about &apos;/s in. cubes, were cut from the bars, sealed in individual Vycor tubes, and heat treated as described. All specimens heat treated at the same temperature were processed together. Samples were quenched by breaking the Vycor tube rapidly under water. Metallographic Examination Specimens were mounted in bakelite and ground wet on 180 grit paper held on a 1750 rpm disk. They were then ground wet by hand, using 240, 400, and 600 grit papers. The rough grinding was continued long enough to get well below the surface. Specimens were mounted separately because of the variation in the rate of etching between alloys. The specimens were polished with rouge on a 4 in., 1725 rpm wheel covered with Miracloth. Alloys on the titanium side of the compound composition were etched with a solution of 2 pct hydrofluoric acid in water saturated with oxalic acid. A few crystals of ferric nitrate were added as a bright -ener. Specimens were immersed 5 sec, polished to remove the etch, then re-etched. With the higher titanium alloys, it was often necessary to start the etch on the polishing wheel, because of the formation of a passive film. In some instances, a plain 2 pct hydrofluoric etch was satisfactory. For the alloys on the uranium side of the compound, a distinction between the compound and the uranium phase developed after standing a short time in air. This could be hastened by the application of heat, such as obtained by placing the specimen on a radiator. A deep etch was necessary to develop details in the uranium-rich phase, such as the Widmanstaetten pattern sometimes obtained by quenching y uranium. A 2 pct hydrofluoric acid solution was used for this deep etching.

Jan 1, 1955

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of&apos; 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 &apos; and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

By R. E. Smallman

R. E. Smallman (University of Birmingham, England)—Recently, Tedmon and Ferriss11 have determined the yield stress parameters oi and ky for tantalum by measuring the lower yield stress as a function of grain size 2d and fitting the results to a relationship of the form They report that although ky , which is taken to be a measure of the dislocation locking strength, is small (- 2 to 4 x 106 cgs units) a substantial yield drop is nevertheless observed in a normal tensile test. Niobium gives a similar result,12-14 as pointed out in the original work by Adams et a1.,12 and in order to check this apparent anomaly the yield-stress parameters of electron beam-melted niobium have recently been reanalyzed15 by the Luders strain technique. In this method the strain hardening part of the stress-strain curve is extrapolated to zero plastic strain; the intercept on the preyield portion of the curve is taken to give oi, whilst the difference between oi and the lower yield stress gives kyd-1/2. The results indicate that ky increases with increasing grain size and hence, a plot of vs d-112 yields an apparent ky, which is lower than the true value. A similar effect could account for the small ky found in the relatively pure tantalum used by Tedmon and Ferriss. The variation of ky with grain size shows that dislocations are more strongly locked in coarse-grained specimens than in fine-grained samples. In niobium, this may be attributed to the fact that the dislocation density in the fine-grained material is higher than that found in the coarse-grained samples which are given a sufficiently prolonged anneal to remove any residual substructure and, since the metal contains only a small amount of interstitual impurity, a variation in locking occurs. By contrast, application of both the grain size analysis and the Luders strain method to yield-stress data from commercially pure vanadium containing a large amount of interstitial impurity gives consistent values of oi and ky, with ky independent of grain size and temperature. Electron microscope observations show minor variations in dislocation density from grain size to grain size, but in any case in this material the dislocations are heavily locked with precipitate. On yielding new dislocations are generated and, as a consequence, the importance of any differences in dislocation density between the various specimens of different grain size is considerably reduced. It is perhaps significant that Adams and lannucci,16 working with a grade of tantalum containing a higher interstitial content than that used by Tedmon and Ferriss, prepared the specimens of different grain size by annealing in the temperature range 1500" to 2000° C to minimize any differences in dislocation structure, and found that ky had a value of 1.04 x 107 cgs units, independent of testing temperature. Such behavior is consistent with the dislocations being locked by carbide precipitates so that the generation of free dislocations is an athermal process. The recent work of Gilbert et al.17 also shows that in tantalum there is no significant variation of ky with grain size provided it contains 150 ppm of oxygen. In this case, however, the dislocations are not locked by precipitate and ky is temperature dependent. C. S. Tedmon and D. P. Ferriss (authors&apos; reply)— We would like to thank Dr. Smallman for his interesting comments and discussion to our paper, "The Dependence of Yield Stress on Grain Size for Tantalum and a 10 pct W-90 pct Ta Alloy".18 It was suggested that perhaps the relatively small values obtained by us for ky of tantalum could be attributed to the same cause that accounts for the apparently small values of ky that result when it is determined by the Luders Strain technique. Since our values were obtained by plotting the lower yield stress vs the reciprocal of the square root of the grain size, it is not clear how this could be the case. The values of ky in this experiment have been calculated, using the Luders strain technique. With this method, values for ky on the order of 2 x 105 to 5 x lo6 cgs units were obtained. In spite of this rather large variation, the magnitudes are still small, and there appeared to be no good correlation between ky and the grain size or the yield stress, probably because of the difficulty in accurately extrapolating the work-hardening portion of the curve back to zero plastic strain. As was shown in the original data,18 there was little work hardening in any of the curves, at any temperature. In his discussion, Dr. Smallman also points out how ky has been observed to increase with increasing grain size, when determined by the Luders strain technique. There are at least two possible explanations for this. In the first case, if it is assumed that the bulk of the interstitial impurities are concentrated at the grain boundaries, then, of course, the available grain boundary area would decrease with increasing grain size, thus presenting less area for the interstitials, which would then presumably increase the concentration within the grains, thereby increasing the locking of the dislocations. In the second case, the increase in ky with increasing grain size would be attributed to the nature of the grain boundary itself. One of the several ways of deriving the Hall-Petch equation19 is based on the stress concentration arising from a pile-up of dislocations at the boundary. The ability of the stress concentration to unlock a source in a neighboring grain would depend on the strength of the grain boundary. As is well-known, the nature and struc-

Jan 1, 1963

By K. F. G. Hosking

I read Professor Gaudin&apos;s paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov6 published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S3), is ground with sodium or potassium hydroxide. the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture. I have employed a similar technique to determine the approximate magnesia content of certain limestones.&apos; The method depends essentially on the fact that when a sample of limestone is ground under controlled conditions with solutions of sodium hydroxide and Titan yellow the color of the final product is, within limits, a function of the amount of magnesia present. I have also shown that the components of a wide range of minerals can be identified by applying chemicals to their streaks on portions of vitrified, unglazed floor tiles, etc. Under such circumstances the diversity of the reactions which take place in the cold (because of the reactivity of fresh corners and edges) is surprising. Thus, for example, if a garnierite, (Ni,Mg)3Si2O5(OH)1, streak is treated first with a drop of 0.880 ammonia and then with a drop of a 1 pct alcoholic dimethyl-glyoxime it immediately becomes red, indicating the presence of nickel.&apos; Stevens and Carron9 have evolved a simple field test for distinguishing minerals by "abrasion pH." A soft nonabsorbent mineral is scratched in a drop of water on a streak plate until a milky suspension is formed. A piece of pH indicator paper is dipped into the suspension, after which it is removed and the maximum deviation from neutrality noted. When a hard mineral or one which absorbs water is being tested, fragments are first ground for 1 min with a few drops of water in a mortar to make a heavy suspension. The importance of the findings of such tests to mineral dressing may be judged by the abrasion pH values, Table 11, recorded by Stevens and Carron for certain species usually regarded as comparatively inert. The combined results Of the above researches clearly indicate that comminution is capable of altering the pH of a pulp and of causing the chemical nature of the surfaces of some of the components to be profoundly changed&apos; Depending On circumstances such surface alterations may have a beneficial or an adverse effect if these products are subsequently subjected to flotation. The tests also suggest that by grinding "inert" minerals with appropriate solid or liquid reagents "reactive" surfaces may be developed which might facilitate separations by flotation. It is an interesting and instructive problem to determine the reactions that are likely to take place when dry solid substances are subjected to comminution and to the unavoidable heat liberated during the process. To do this it is theoretically necessary to know the free energy values of the reactants and possible resultants, but unfortunately there is a dearth of such data! However, the heats of formation of many substances are known, and generally speaking, if in a reaction of the type AB + CD = AD + CB the sum of the heats of formation of AB and CD is less than that of AD and CB the reaction will probably proceed to the right. Thus, according to a note I have (the author of which I cannot name) if PbS (black) is warmed with CdSO, (white), PbSO., (white) and CdS (yellow) are formed, and that the reaction does, in fact, take place is indicated by the change in color of the mixture. The reaction is expected, as the sum of the heats of formation of PbS and CdSO, is less than that of PbSO, and CdS (as shown below). PbS + CdSO4 = PbSO4 + CdS 22.2 + 218.0 < 216.2 + 33.9 Finally, certain other aspects of the chemistry of comminution, which are neither mentioned by Professor Gaudin nor referred to by me are to be found in a paper by Welsh" and in the printed discussion thereof. A. M. Gaudin (author&apos;s reply)—The observations contributed by Dr. Hosking are indeed welcome, as they add to our experimental knowledge of a topic which is believed to be of the first importance. In connection with the experiments cited it should be kept in mind that oxidation, hydration, and carbonation at various rates should always be deemed to be possibilities when grinding is done in water or in air, even in "industrially dry" air. Special precautions might lead to sufficient minimizing of these reactions and to the assertion, instead, of deliberately-created reactions. The author wishes to thank Dr. Hosking for his contribution.

Jan 1, 1957

By L. C. Brown, E. B. Hawbolt

The formation of grain boundary precipitates has been studied in Ag-5.64 wt pcl Al alloys at 688°C. Large-grain specinzerzs were used and the boundary misorientation measured by X-ray diffraction. At low-angle grain boundrrries Primary sideplates form. u)hile abore a 17-deg misorientation lenticular precipitates predominate. Growth of the lenticular precipitates was studied on individual grain boundaries using a statistical technique. The thickening and lengthening rates appeared to be independent of &apos;pain boundary misorientation, indicating that grain boundary diffusion was not significant in this system. The precipitates grew urith constant shape, with both the length and thickness increasing parabolically with time. The parabolic lengthening rates were unexpected since previous theory and experimerztal results had indicated linear growth. By approximating the shape of the precipitate to that of an oblate spheroid grouling with constant shape an equivalent diffusion coefficienl was calculated. The zlalue obtained was in good agreement with nleasurements obtained fron, diffusiorz couples. IF a single-phase alloy is heated or cooled to a temperature such that the phase becomes supersaturated, there is a tendency for a second phase to precipitate from it in order to remove the supersaturation. Precipitation takes place initially on grain boundaries due to preferred heterogeneous nucleation, but subsequently Widmans kitten plates may form in the grain interiors if the grain size and supersaturation are sufficient. The type of grain boundary precipitate formed depends on the nature of the boundary. Aaronson1 and clark2 have shown that grain boundary misorientation can be characterized by the simple parameter R, where and X, Y, and Z represent the minimum rotations about three orthogonal axes required to bring the two lattices forming the grain boundary into coincidence. The maximum value for R is 60 deg. In using this parameter the orientation of the grain boundary itself is, of course, neglected. However it was found in both Fe-si3 and A1-Ag2 that the precipitate shape depended only on the parameter R. Clark found that the vast majority of precipitates formed were allo-triomorphs— lens-shaped precipitates that grew along the grain boundaries. At low-angle boundaries, however, (R < 15 deg) Widmanstatten sideplates nucleated at the grain boundaries and grew into the adjacent grains. It has been reported that the rate of growth of grain boundary precipitates is controlled by diffusion within the supersaturated phase.&apos; The theories which have been developed for growth rates have assumed the diffusion coefficient constant over the composition range of the supersaturated phase. This is a fairly good approximation if the composition range involved is not large. Thickening rates have been calculated using the theory developed by Zener4 and by Frank5 for the growth of planar precipitates. A parabolic growth law

Jan 1, 1968

By J. A. Younkins, J. A. Brooke

In 1931 the Philadelphia Company acquired by lease several coal mines in southern Greene County, Pennsylvania. These mines were known as the "Dora," "Seventh Pool" and "Rosedale" mines in the Sewickley seam, and the "Rosemary," "Seventh Pool" and "Warwick" mines in the Pittsburgh seam. All these mines are in the immediate vicinity of Greensboro, Pa., with considerable river frontage on both sides of that village. The mines in each seam are contiguous and to some extent the properties in the two seams lie one above the other. In 1938 the property known as the "Sandy Run mine," in the Sewickley seam, adjoining the Dora mine, was purchased from the Fredericktown Coal and Coke Co. Altogether, by purchase and lease, the company gained control of approximately 3400 acres of coal land in Greene County, from which it was estimated that some 20,000,000 tons of coal could be extracted. Geology of Warwick Properties Both seams of coal outcrop along or near the river on both sides of the town of Greensbgro. They lie on the eastern slope of the Lambert syncline, near the southern end of the axis, consequently the predominant dip of the seams is away from the river, so that development for river handling has the unavoidable disadvantage of adverse grades for haulage to the outside. Predominant grades away from the river at right angles to the "butt" cleat of the coal average about 2.25 per cent dipping in a westerly direction, but local dips occur, which are considerably greater. Predominant grades parallel to the river and at right angles to the "face" cleat of the coal average about one per cent dipping in a northerly direction. Both seams of coal lie in the Monongahela formation, the Pittsburgh bed being the bottom measure of the formation and the Sewickley bed lying about 90 it. above. Approximately midway between the two lies the Redstone coal bed, which is generally thin and of erratic occurrence and therefore of little commercial value. It is mined only locally where it attains sufficient thickness. Sewickley Bed The Sewickley bed is commonly called the "five-foot" or Mapletown" seam, because in Pennsylvania it reaches its greatest thickness and has been mined most extensively in the vicinity of the village of illapletown, approximately one mile west of Greensboro. In the early development of the Warwick properties, which occurred near the river, the seam had an average of 5 it. 2 in. in height. As development proceeded away from the river, however, the height gradually decreased until the average height of the present workings is about 4 ft. 6 in. Present development is encountering lower coal

Jan 1, 1947

By J. A. Younkins, J. A. Brooke

In 1931 the Philadelphia Company acquired by lease several coal mines in southern Greene County, Pennsylvania. These mines were known as the "Dora," "Seventh Pool" and "Rosedale" mines in the Sewickley seam, and the "Rosemary," "Seventh Pool" and "Warwick" mines in the Pittsburgh seam. All these mines are in the immediate vicinity of Greensboro, Pa., with considerable river frontage on both sides of that village. The mines in each seam are contiguous and to some extent the properties in the two seams lie one above the other. In 1938 the property known as the "Sandy Run mine," in the Sewickley seam, adjoining the Dora mine, was purchased from the Fredericktown Coal and Coke Co. Altogether, by purchase and lease, the company gained control of approximately 3400 acres of coal land in Greene County, from which it was estimated that some 20,000,000 tons of coal could be extracted. Geology of Warwick Properties Both seams of coal outcrop along or near the river on both sides of the town of Greensbgro. They lie on the eastern slope of the Lambert syncline, near the southern end of the axis, consequently the predominant dip of the seams is away from the river, so that development for river handling has the unavoidable disadvantage of adverse grades for haulage to the outside. Predominant grades away from the river at right angles to the "butt" cleat of the coal average about 2.25 per cent dipping in a westerly direction, but local dips occur, which are considerably greater. Predominant grades parallel to the river and at right angles to the "face" cleat of the coal average about one per cent dipping in a northerly direction. Both seams of coal lie in the Monongahela formation, the Pittsburgh bed being the bottom measure of the formation and the Sewickley bed lying about 90 it. above. Approximately midway between the two lies the Redstone coal bed, which is generally thin and of erratic occurrence and therefore of little commercial value. It is mined only locally where it attains sufficient thickness. Sewickley Bed The Sewickley bed is commonly called the "five-foot" or Mapletown" seam, because in Pennsylvania it reaches its greatest thickness and has been mined most extensively in the vicinity of the village of illapletown, approximately one mile west of Greensboro. In the early development of the Warwick properties, which occurred near the river, the seam had an average of 5 it. 2 in. in height. As development proceeded away from the river, however, the height gradually decreased until the average height of the present workings is about 4 ft. 6 in. Present development is encountering lower coal

Jan 1, 1947

By C. G. Dunn

IT is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.1 In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth-processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insufficient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered. Until recently observations were that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro- structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1946

By R. C. Earlougher, F. G. Miller, T. D. Mueller, H. J. Ramey

There are many studies of flow in radial systems that can be used to interpret unsteady rerervoir flow problems. Although solutions for systems of infinite extent can be used to generate solutions fur finite ow systems by superposition, application is tedious. In this paper a step is made toward simplifying calcu1ations of such solutions for finite flow systems. Superposition is used to produce a tabulu-lion of the dimension1e.s.s pressure drop function at several locations within a bounded square that has a well at its center. The square system provides a useful building block that may be used to generate flow behavior for any rectangular shape whose sides are in integral ratios. Values of the tabulated dimensionless pressure drop function are simply added to obtain the dimensionless pressure drop function for the desired rectangulm system. The rectangular system may contain any number of wells producing at any rates. Furthermore, the outer boundaries of the rectangular system may be closed (no-flow) or they may he at constant pressure. Mixed conditions also may be conyidered. Tables of the dimensionless pressure drop function for the square system are presented and various applications of the technique are illustrated. Introduction In 1945, van Everdingen and Hurst&apos; published solutions for the problem of water influx into a cylindrical reservoir. Since this problem is mathematically identical with the depletion of a cylindrical reservoir with a well at the origin, the van Everdingen-Hurst solution may be used to study the depletion problem. In their analysis, they assumed that the fluid had a small, constant compressibility such that flow was governed by the diffusivity equation For a constant production rate q starting at time zero, van Everdingen and Hurst showed that the unsteady pressurc distribution for both finite and infinite systems could be expressed in terms of a dimensionless pressure &apos;Sabulations of the dimensionless pressure drop for a unit value of r, were provided by van Everdingen and Hurst,&apos; and later by Chatas.&apos; Others also presented values in graphical or tabular form." If the radius of the well becomes vanishingly small, r,+ O, the line source solution may be used for Eq. 2 when infinite systems are considered. Eqs. 5 and 6 are excellent approximations for Eq. 2 under certain conditions: In 1954, Matthews, Brons and HazebroekV emonstrated that solutions such as Eq. 5 can be superposed to generate the behavior of bounded geometric shapes; i.e., the behavior of a bounded single-well system can be calculated by adding together the pressure disturbances caused by the appropriate array of an infinite number of wells producing from an infinite system. These wells are referred to as image wells. Matthews, Brons and Hazebroek considered systems containing a single well producing at a constant rate. This superposition can be represented analytically as

Jan 1, 1969

By J. H. Richards, G. Derge, W. Peifer

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,&apos; and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949