Search Documents

By W. C. Winegard, J. R. Carruthers, A. Plumtree, L. R. Morris

The unidirectional solidification of dendrites containing central twin planes was studied in A1-Ti alloys. Once nucleated, the twinned dendrites are a Twore ejficient form for solute redistribution and therefore grow in preference to the normal columnar dendvites. Comparison of these twinned dendrites to adjacent colunmar dendrites by means of decanting experinzents and electron-probe rnicvoarmlysis indicates that these special dendrites grow with less undercooling than normal dendrites. These findings are further supported by the effect of forced convection on the dendrite morphologies. COMMERCIAL semicontinuous cast ingots of most aluminum alloys frequently exhibit large grains which appear to be composed of hundreds of parallel, continuous, thin lamellae. This structure has been termed "basaltic",' "fiederkristall", or, commonly, "feathery grain". The lamellae are 'about 100 p thick, several inches long, and each lamella contains a central (111) coherent twin boundary. The feathery grain has been reported to have a (112) direction2 and a (110) direction4 in the twin plane parallel to the casting direction, in contrast with the usual columnar structure where a (100) direction predominates. Aust et uZ.~ proposed that the twin boundaries were growth twins nucleated by stacking faults on the octahedral planes. chalmers6 has suggested that feathery grain may grow by a re-entrant edge mechanism, as proposed by wagner7 for twinned dendritic growth in germanium. Cahn et ~1.~ have concluded that the occurrence of feathery grain is evidence of some form of lateral layer growth rather than the atomically continuous growth normally observed in metals. The postulates by Chalmers and Cahn would seem to be contradicted by the work of Nakao~"' who showed that feathery grain only occurs when growth rates are high and the aluminum contains some solute. Specifically, Nakao found that in order to obtain feathery grain, in small castings solidified unidirec-tionally upward, the rate of growth must be above 2.4 cm per min and a critical solute concentration must be present. Below this solute concentration the grain structure was totally columnar. The critical solute concentration was found to be approximately: 0.04 wt pct Ti, 2 wt pct Cu or Mg, and 8 wt pct Zn. As pointed out by Chalmers it is not obvious why a twin-plane re-entrant edge mechanism would occur in aluminum which is thought to have a diffuse solid-liquid interface. The present experiments were undertaken to determine the growth mechanisms in- volved and to study the solute segregation in more detail. EXPERIMENTAL PROCEDURES Alloys ranging in composition from 0.05 to 0.23 wt pct Ti* were prepared from 99.9 pct pure Ti and 99.993 pct pure Al. Two-hundred-gram samples of A1-Ti binary alloys were solidified unidirectionally and vertically upward from a water-cooled copper base, in a heated insulated mold. The 1-in.-diam, 6-in.-length mold was made of Marinite (manufactured by Johns-Manville Co.). The mold was attached to a 24-in. pivoted arm such that by dropping a weight the mold was rotated 180 deg, throwing the liquid metal from the solid. In this way, the solid-liquid interface was revealed by decanting. A sketch of the decanting mold is shown in Fig. 1. The alloy was poured into the mold at temperatures ranging from 680" to 750°C, partially solidified by water cooling from the base, and decanted after a measured time interval. Growth rates for each metal-pouring temperature were calculated from solidification-time vs length solidified curves. Temperature gradients in the melt were measured using four No. 34 gage thermocouples which protruded into the mold cavity. Grain orientations were determined by X-ray diffraction using Laue back-reflection techniques. Grain substructures were examined metallographically, using polarized light, by applying a thin epitaxial anodic film to polished sections after the method of Hone and pearson." Titanium micro segregation was measured by electron-probe microanalysis using a NORELCO AMR/~ with a mica crystal and proportional-flow counter. Several of the cast samples exhibited feathery and columnar dendrites growing in the same direction and

Jan 1, 1967

By G. A. Moore

A brief review is given of methods designed to produce metallic iron of high purity, and typical results are listed. A recent method, utilized at the National Bureau of Standards, consists of the extraction of ferric chloride by ether, reduction of this ferric chloride to ferrous chloride, further purification of this chloride, and the subsequent electrolytic deposition of metallic iron. iron produced by this procedure apparently is softer than, and otherwise different in properties from, any iron previously prepared and contains appreciably smaller amounts of impurities. THE history of attempts to produce "pure" iron reaches to antiquity and it may be presumed that each ancient armorer who succeeded in making a better steel concluded, correctly, that he had done a better job of removing the "base metals," and incorrectly, that he now at last had a "pure" metal. Early metallurgical papers mentioned use of "pure iron" in making alloys—this "pure" iron in most cases being inferior to some commercial stocks of the present time. Improvement has been continuous, and usually at a sufficient rate to convince each succeeding group of workers that they, at last, were using the really pure metal (until the analysts also improved their techniques to again discover the impurities). These adventures were reviewed in some detail by Cleaves and Thompson.' Although the ores of a metal may be abundant, difficulties in extracting it may make the pure metal very rare. When impurities are restricted to a total of a few parts per million, nearly all pure metals become rarities. Lead, copper, gold, mercury, silver, zinc, aluminum, bismuth, and the six platinum metals are claimed to be available with total impurities ranging from 2 to 50 ppm. The present small and scattered world supply of so-called "pure" iron holds an unimpressive place in another group of 16 metals having approximately 100 ppm of foreign material. Of about 20 less rare metals, only the platinum metals are more costly to prepare. While the production of such rare varieties of iron may appear insignificant in the presence of thousand-ton operations with 95 to 99 pct metal, it must be emphasized that all researches on commercially interesting irons and steels are in fact studies of the modifications of the properties of iron by additional materials. Until the properties of high purity iron are directly measured, all ferrous research must operate without known base values. Traces of impurities may affect the properties of a metal in many ways. Infinitesimal traces of solutes, by disturbing the electronic configuration, greatly change the electrical properties of transistors and semiconductors2-3 and slightly larger traces might alter these quantities in iron. Soluble impurities which disturb the perfection of lattice arrangement not only may alter the magnetic constants and electric properties, but by their close association with dislocation phenomena probably control the very existence of the "yield point"; determine the value of yield stress; and perhaps control the selection of slip and cleavage planes. It has been speculated that impurities might even cause the allotropic transformation in iron, but in any case their rearrangement must contribute to the unreliability of heat capacity and other thermodynamic measurements. Impurities which do not remain in solution may cause even greater effects on the properties. Microscopically visible amounts of phases other than ferrite can be found in all high purity irons which have come to my attention. It can be calculated that from 50 to as little as 2 ppm of an insoluble material might be sufficient to completely film all grain boundaries in irons having grain sizes from ASTM Nos. 10 to 1. Should this occur, such films, even though invisible, may be very important in fracture problems, especially at extremes of temperature:' Studies of grain growth and diffusion normally imply consideration of a single-phase system, hence, in the presence of insoluble impurities they can be expected to give ambiguous data." High purity iron is also in demand for use as chemical and spectro-chemical standards; for work in classifying the lines of the iron spectrum; for biological work in nutrition; and for work in nuclear physics. where the presence of some sensitive

Jan 1, 1954

By J. J. Gilman, T. A. Read

S URFACE effects in the cleavage of brittle crystals have been known for some oftime,1, 2 but our knowledge of surface effects in the plastic deformation of crystals is of relatively recent origin. In 1936, Roscoe9 eported his observations comparing oxidized and clean cadmium crystals. He found that cadmium crystals 1/2 mm in diam when covered by an oxide film less than 1200 atoms thick had critical shear stresses about twice those for clean crystals. This effect is anomalous in that it cannot be caused by the inherent shear strength of a normal oxide film. Either an interaction between the film and the crystal causes the large increase in strength, or the oxide film has an abnormal mechanical strength. Several authors since Roscoe have studied surface effects in crystal plasticity. A complete review of the literature will not be presented, but most of the results may be summarized as follows: 1—The critical shear stress for slip is increased markedly by very thin oxide films on zinc4 and cadmium crystals;" ' also, the entire stress-strain curve is raised by an oxide coating;3,4 both effects increase with decreasing specimen radius. 2—Surface active substances such as oleic acid destroy the hardening effect of oxide films.4, 6-8 The time required for the reduction of the hardening effect to begin increases with the viscosity of the solvent4~ 3—There has been dispute in recent years about the effects of surface active substances themselves on plastic deformation. Rehbinder, Lichtmann, and Maslenikov9 state that surface active substances reduce the strength of metal monocrystals markedly and increase the number of slip lines per unit length at a given strain. The effect varies with orientation for tin crystals being smallest for x, = 0, largest for x, = 45", and intermediate as x, + 90°.10 Several workers claim to have disproved the results of Rehbinder')"." but Rehbinder and Lichtmann9 have defended themselves and Masing with his collaborators" has confirmed some of Rehbinder's results. 4—Immersion of metal specimens in electrolytes such as sodium chloride reduces their strength12,13' and subsequent cathodic polarization increases the strength reduction. For noble metals, the strength reduction occurs for both anodic and cathodic polarization," increasing with increasing polarizing voltage. 5—Electroplated copper coatings effect the creep rates of zinc monocrystals. Poly crystals are not affected." 6—Immersion in dilute acid destroys the hardening effect of an hydroxide film. When an acid solution is applied to a steadily creeping crystal, the creep rate jumps to a very high value and then drops gradually to a steady value which is higher than the initial steady rate.*' " If the hydroxide film to be removed is very thin (about 100A thick), the creep rate does not change measurably, but a small rapid strain-increment is observed when dilute acid is applied." 7—Crystal plasticity depends on specimen dimensions. This was observed by Lichtmann and Ven-stroml" for monocrystalline tin and by Andrade and Kennedy" for polycrystalline lead. 8—Immerson of copper crystals in mercury has no effect on their stress-strain curves.'" 9—Bombardment of creeping cadmium crystals with a particles which penetrate the surface to only 0.005 mm may increase their creep rates as much as five times.''' The experiments which will be described in this paper pertain to: (a) the effect of a crystal's shape on its plastic deformation, and (b) the effect of metallic surface films on plastic deformation. For the work pertaining to (a), crystals of zinc, tin, and lead were grown which had various shapes. These were tested in simple tension. Macroscopic rotations about the tension axis which are unpredicted by the classical theory of slip were observed, and serrated edges were observed in tin crystals. For the work pertaining to (b), the effects of evaporated and electrodeposited films of copper, nickel, gold, and zinc on the mechanical properties of zinc, tin, and lead crystals were determined. The films influenced both slip and twinning of the crystals in creep and tensile tests. Experimental Details Chemically pure zinc, tin, and lead were used in this investigation. The zinc was 99.999t pct pure;

Jan 1, 1953

By B. J. Bayles, J. A. Ford, M. J. Salkind

Unidirecltonally sulidijied AL-A13Ni was found to exliibit excellent microstructural stability to 508°C. Above this temperature the transverse micvostructure coarsened in a manner analogous to "Ostwald Ripening", but the A13Ni whiskers did not spheroidize or foreshorlen. The coarsened whiskers reinforced the matrix as effectirely as the finer whiskevs and no reduction in room-temperature tensile strength mas noled after exposure for 90 hr at 96 pel 0-1 the absollite melling temperature of the eulectic. The slability was auribucted to the presence of low-index (and presurrlably lor-energy) cvystallographic interjaces between phases. The driving force for microstructural coursening was presumed to be the reduction of interfacial energy between the phases. Finer micvoslructures were found to coarsen more rapidly than those which weve imitally coarser. FIBER-reinforced metals have been shown to exhibit good short-time tensile properties at elevated temperatures.1-4 However, many elevated-temperature applications require long-time property retention which dictates the necessity for microstructural stability. Two types of instability are common to fiber composities. The first, chemical instability, is due to chemical reaction between the matrix and the relnforcing phase. Petrasek and weeton5 have shown that chemical reaction between tungsten wire and several copper alloy matrices resulted in degradation of the reinforcing phase and reduction in strength of the composite materials. Kreider and Leverant4 have noted similar behavior for boron-reinforced aluminum above 400°C. The second type of instability arises in systems in which the phases are essentially chemically stable with respect to each other and is characterized by spheroidization and/or agglomeration of the reinforcing phase. parratt6 has reported this type of degradation to occur relatively rapidly at moderate temperatures for nickel and cobalt alloys containing whiskers of silicon nitride, aluminum oxide, and silicon carbide and has identified it as "physicochemical" instability. Although both types of instability are the result of the differences in the chemical potential between the fibrous phase and the matrix, they may be differentiated by the fact that the second type, "physicochemi-call' instability, results in little or no net change in the composition or amount of each phase present. It does, however, result in a morphological change which profoundly affects the strengthening mechanism. Chemical interaction. on the other hand, results in a change in the composition and amount of one or more of the phases present, or the appearance of a new phase. In the latter case, the appearance of the mi-crostructure, that of a fibrous phase aligned in a matrix, may remain essentially unchanged, but the chemical degradation of the fiber results in markedly reduced composite strength. This investigation was initiated in an attempt to evaluate the microstructural and related mechanical property changes of a whisker-reinforced eutectic composite after elevated-temperature exposure. The composite system chosen for this study was the uni-directionally solidified A1-A13Ni eutectic which Lemkey. Hertzberg, and Ford7,8 demonstrated to behave as a whisker-reinforced composite. The microstructure of the unidirectionally solidified material consists of aligned needles of A13Ni in a matrix of aluminum. EXPERIMENTAL PROCEDURE Eutectic ingots having a nominal composition of 6.2 wt pct Ni were produced by melting 99.99+ pct A1 and 99.99 pct Ni in recrystallized alumina crucibles in an argon atmosphere. The analyses of the starting materials are listed in Table I. These master heats were cut up? melted by induction heating, and unidirectionally solidified vertically in 1/2 -in.-ID. 6-in.-long graphite crucibles, in a dynamic argon atmosphere. Therma1 gradients in the liquid were determined by measuring the temperature in the melt as a function of apparatus travel distance, as discussed by Kraft and Albright.9 The rate of solidification was assumed to be equal to the uniform rate at which the crucible assembly was withdrawn from the furnace. Ingots representative of nominal growth rates of 2, 5, and 11 cm per hr were produced and the solidification parameters are summarized in Table 11. Ingots used for met allographic analysis were pre-

Jan 1, 1968

By T. W. Watson, D. R. Flynn

Measurements have been made of the thermal conductivity and electrical resistivity of two specimens of 0.005-cm (2-mil) Be-Cufoil over the temperature range -140° to +200°C. The thermal cmductivity of Be-Cu Alloy 125 was found to be significantly higher than that of Alloy 25, which had a higher impurity content. The thermal conductivity and electrical resistivity values obtained were in concordance with the Smith and Palmer relation for copper alloys which states that ? = 0.0239 (T/p) + 0.075 where A is thermal conductivity (W cm-' deg-'), p is electrical resistivity (microhm-cm), and T is absolute temperature (OK) , indicating that the Smith and Palmer relation can be used to predict the thermal conductivity of this type of Be-Cu alloy over the temperature range -140" to + 200°C to within an accuracy suitable for most engineering applications. THE National Aeronautics and Space Administration, Goddard Space Flight Center, Greenbelt, Md., requested the National Bureau of Standards to measure the thermal conductivity of 0.005-cm Be-Cu foil which was to be used to fabricate antennae for use in Radio Astronomy Explorer space craft. It was felt that measurements had to be made on the actual antenna material, rather than on a thick bar of similar material, since the cold-working and age-hardening properties of the alloy would make it very difficult, if not impossible, to place a thick bar in the same metallurgical state as the 0.005-cm material. As discussed in Section 111 of this paper, the thermal conductivity of many copper alloys can be computed rather accurately from electrical resistivity data using an empirical relation developed by Smith and palmer' and further confirmed by owell.' However, there has been very little work done on correlating thermal and electrical conductivities on Be-Cu alloys. We were reluctant to assume the validity of the Smith-Palmer relation on Be-Cu alloys because of the very large mass difference between beryllium and copper. As will be seen, however, our experimental results indicate that the Smith-Palmer relation is valid for the two alloys on which we made measurements. I) DESCRIPTION OF SAMPLES Samples of Be-Cu Alloy 25 and Be-Cu Alloy 125 were furnished to NBS in the form of rolled strip material, 0.005 cm thick by 5.08 cm wide. The Be-Cu Alloy 25 was purchased by NBS in the form of a continuous length of flat strip. The Be-Cu Alloy 125 was furnished to NBS by Goddard Space Flight Center in the form of two lengths of strip that had been formed into "tubing" of about 1.2 cm diam, with one side of the strip overlapping (but not connected to) the other side by about 90 deg. This "tubing" had been opened up to be flat and then rolled onto spools of about 3 cm diam. When unrolled, the strip would spring back into tubular form. Samples of both of the Be-Cu alloys were chemically analyzed by the NBS Analytical Chemistry Division. The beryllium content was determined quantitatively by the phosphate-gravimetric method to be 1.83 wt pct for Alloy 25 and 1.80 wt pct for Alloy 125. The two alloys were also examined by a general qualitative spectrochemical method for metallic elements. The Alloy 25 specimen contained between 0.1 and 1.0 wt pct Al, Co, Fe, and Si and between 0.01 and 0.1 pct Ni. The Alloy 125 specimen contained between 0.1 and 1.0 pct Co and between 0.01 and 0.1 pct Al, Fe, and Si. Other metallic elements present were in amounts less than 0.01 pct. The NBS Engineering Metallurgy Section measured the tensile strength, elongation, and Knoop hardness of both the Be-Cu Alloy 25 and the Be-Cu Alloy 125. These are given in Table I. The NBS Engineering Metallurgy Section also prepared photomicrographs of the two alloys; these are shown in Figs. 1 and 2.

Jan 1, 1969

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By T. Seldenrath

In the development of a fluid -operated hammer drill' for accelerated penetration of hard rock formations in oil wells, a research investigation was conducted to evaluate the percussion effects obtained with different design characteristics and to determine the possibilities of percussion in the low frequency range. Tests were conducted on granite blocks and comparable impact forces were measured with a load cell under selected test conditions. These full-scale laboratory tests provided an evaluation of the effectiveness of percussion which was further supported by actual downhole field performance. While much pertinent data have been presented by other investigators the method of evaluation described in this article resulted in good correlation between laboratory and field performance and may be applicable in other low frequency percussion developments. EXPERIMENTAL METHOD For these tests the bit was held stationary and the test block was rotated and forced upward against the bit by a hydraulically-lifted rotary table. "Weight on bit" was calculated from pressure readings on the fluid system of the lifting cylinders—corrected for tare and friction. Percussion was obtained with several tubular hammers of different weights up to 320 lb. These were lifted mechanically and allowed to drop by gravity from various heights onto a slidably-mounted bit sub or "floating anvil" for calibration of the load cell response with known kinetic energy of the hammers. During evaluation of percussion effects, the hammers were hydraulically operated to provide a range of percussion frequencies up to 1,020 blows per minute delivered to the anvil. To obtain comparable test readings, the load cell of the strain gauge type, was attached to the bottom of the anvil or bit sub in place of the bit. The load cell rested on a typical granite test block mounted on the drilling table. The latter was hydraulically supported as in the actual drilling operation. The effect of support resistance was the same for all tools when calibrating. Impact forces so determined werethusdirectly comparable with one another for the purposes of this investigation. When a roller bit was substituted for the load cell for actual drilling, the impact force would probably be reduced due to the resiliency of the bit body, legs. cones and teeth and the penetration of the teeth into the rock. However, since the bits and rock specimens were uniform in these tests, an evaluation of actual tool performance, in terms of parameters previously determined with the load cell at the selected standard conditions of calibration, proved satisfactory. Throughout these tests, 8¾-in. standard tricone, hard rock toothed roller bits and carbide-insert roller bits were used. Rotary speeds were 50 and 100 rpm; static weight on bit was applied up to 40,000 Ib, and percussion frequencies up to 1,020 blows per minute were available. During this investigation it was found that toothed bits on which the teeth had developed flat ends about 3/16 in. wide did not change appreciably for the duration of a test. Hence, all toothed bits used in this study were in this condition. Conventional reference curves obtained in these tests show that increasing weight on hit by 2:1 yielded an increased penetration rate of approximately 2.7:1, while an increase in rotary speed of 2:1 netted an increased penetration rate of roughly 1.7:l. Results are thus of the same order as those reported for hard rock drilling by other investigators." CALIBRATION Under the selected standard test conditions previously described, with the lifting table hydraulically supported, and the anvil interposed between hammer and load cell, the hammers were dropped from known heights. Thus, with the kinetic energy of the hammer known, the corresponding maximum impact force shown by the cell was determined. (It may be of passing interest to note here that special drop tests with the hammers showed that no appreciable reduction in impact force resulted from introduction of the anvil or hit sub.) From these calibrations, it was possible to determine the theoretical kinetic energy available in the hammer from the maximum impact force shown by the load cell while operat-

By Strathmore R. B. Cooke, Paul B. Queneau

The kinetics of the dissolution of scheelite in basic solutions of carbonate and fluoride were investigated. Work was also done with solutions of alkali metal chloride, hydroxide, phosphate, and mixtures of phosphate and fluoride. The study was conducted at 90 psig and at temperatures ranging from 100" to 155"C, and both natural and synthetic scheelite single crystals were used. The interaction of scheelite with carbonate solutions generally followed a parabolic rate law, and resulted in the formation of calcite crystals on the attached surface. The transport of the CO3 through the calcite to the scheelite surface was probably rate -controlling between 115" and 135°C. Positive deviations from Parabolic behavior were observed at 100" and 155?C, presumably due to the calcite grain growth, and to the formation of a noncoherent calcite layer, respectively. The leaching of scheelite with alkaline fluoride solution produced a calcium fluoride reaction-product which covered the surface as a sheet-like layer. Below 110°C the dissolution rate was parabolic; at 115" and 135°C it was linear. In the linear region, the periphery of the calcium fluoride layer lifted from the sample. Only the lower layers, braced by the scheelite substratum, remained unbroken. This bound layer, approximately constant in thickness, limited the rate at which the fluoride could attack the scheelite. The phosphate and phosphate-fluoride leaches dissolved scheelite at a linear rate; solid reaction products were respectively hydroxyapatite and fluorapatite. Sodium hydroxide and chloride were not effective leachants, and did not produce observable solid reaction products. THE feasibility of pressure leaching of scheelite pulps with basic solutions containing either carbonate or fluoride ions, as indicated by the following equations, has been established by previous investigators:1-3 200°C CaWO4s + CO37q - CaCO3s+WO4aq [1] 200°C CaWO4s + 2Faq ^ CaF2s+WO4aq [2] It is to be noted that a commercial process employing reaction [I] is in use at Union Carbide's operation near Bishop, Calif. In the earlier work referred to, it was apparent that the precipitation of the solid reaction-product on the scheelite particles sharply reduced contact of the leachant with the scheelite. We have extended this work by studying the kinetics of dissolution employing single crystals of scheelite of known exposed surface area. In addition, the effectiveness of solutions of phosphate, of phosphate with fluoride, and of chloride and hydroxide as leachants for scheelite have been investigated. EXPERIMENTAL Apparatus. The low-pressure autoclave used in this wo (100 psig maximum) is essentially that of J. Halpern4 as modified by F. A. Forward.5 Constructed entirely of 316 stainless steel, its maximum capacity is 4000 ml. The temperature in the autoclave was regulated to *0.5?C by a Wheelco thermocouple controller. A 4-in. diam, three-bladed impeller, circulated solution upward against the sample, and a strobo-scope permitted holding the stirring rate to *15 rpm. A check valve and a "pop" type safety valve were installed, a sample holder was fixed to an externally adjustable rod, and a water-cooled condenser was placed in series with the sampling valve. The stainless steel sample holder, Fig. 1, held the epoxy-mounted sample (f) five mm above the impeller. Tightening the tapered sleeve (d) positioned the epoxy-resin specimen-mount by forcing it back against the spacer (c). The mount (e) was 1 in. diam. Sample Description and Preparation. Both synthetic and natural scheelite crystals were leached. The former were single crystals of 99.95 pct purity which were leached approximately perpendicular to the "c" axis; they were supplied by the Gallard-Schlesinger Chemical Manufacturing Corp. The natural crystals, supplied by Minerals Unlimited, were transparent, analyzed 99.8 pct CaWO4, and in ultraviolet illumination exhibited the characteristic blue glow of substantially molybdenum-free scheelite. To permit exposure of an essentially constant surface area of scheelite to the leachant, the samples were mounted in Scotchcast Brand Resin No. 250 (Minnesota Mining and Manufacturing Co.). The mount-

Jan 1, 1970

By Jr. Ensign C. O., J. W. Trammell

The two principal methods of room-and-pillar mining practiced at White Pine make it important to predict variations in the thickness and rock types of a stratum called the upper sandstone. In full column mining, the nearly barren upper sandstone occurs between two ore horizons (called upper shale and parting shale, respectively), and is mined as a part of the ore column. In general, full column mining is not practiced where excessive upper sandstone thickness causes full column ore grade to be substantially lower than parting shale ore. In parting shale mining, the upper sandstone forms the mine roof. Difficulty in predicting upper sandstone character arose because the extent and directions of its variations were not apparent in the property's diamond drilling, in which holes are spaced on 1000-ft centers. A study of sedimentary features, undertaken to improve the predictability of trends in the upper sandstone, led to an interpretation of the sedimentary environment in which the sandstone was deposited. Ripple marks, mud cracks, and cross-bedding, as well as other, less well known features, such as channel casts, flute casts, and current crescent casts, were mapped or recorded. These data, coupled with the knowledge of regional facies changes gained from studying drill core, show that the upper sandstone was deposited by a series of streams flowing northeastward over the underlying parting shale. Deposition of the lowermost bed of the upper sandstone, near the ancient shoreline, was locally preceded by erosion of the parting shale, and the greatest thicknesses of sandstone are found in channels scoured out of the parting shale. Awareness of the rather strong linear trends in the upper sandstone makes it possible to project continuous areas of thick upper sandstone through apparently isolated "highs" in the upper sandstone thickness contour map, which is based on drill-hole information. Since local exceptions to general stratigraphic trends exist, a method was also needed for esti- mating, in detail, the thickness and degree of shali-ness of upper sandstone forming the roof in active parting shale mining areas. Because locally the parting shale was thinned by erosion during the deposition of upper sandstone, parting shale thickness is inversely proportional to upper sandstone thickness. Utilizing information taken from short drill holes into the roof, curves were constructed for the correlation of parting shale thickness (measurable in the mine) with the upper sandstone total thickness, as well as the thickness of its basal member. The White Pine mine is situated in Ontonagon County, approximately 6 miles south of Lake Superior, in the Upper Peninsula of Michigan (Fig. 1). The orebody mined by White Pine Copper Co. occurs in the lowermost 20 to 25 ft of the Nonesuch formation, a series of middle- to upper-Keweenawan shales, siltstones, and sandstones. This paper discusses the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the orebody. THE OREBODY AND MINING TYPES A brief description of the orebody and mining methods is necessary to show how the upper sandstone affects mine planning and grade control. In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions, as shown in Fig. 2. Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 2. Other authors1'3 have dealt in detail with the stratigraphy and mineralogy of the orebody. However, in this article, we are concerned with the major subdivisions only, and it will suffice to note the low copper content of the upper sandstone, shown in Fig. 2. At present, two types of room-and-pillar openings are created in the orebody. In one type, called parting

Jan 1, 1964

By R. E. Ogilvie, E. T. Peters

The X-ray Kossel-line method has been used preaioz~sly for measuring lattice parameters to accuracies of 1 part in 100,000.5 A second application of this method is described for determining the crystallographic orientation of a randomly positioned single-crysta1 spherical volume that can he as small as 50 µ in diameter, within accuracy limits of ±1/2 deg. The theory, experimental procedure, and interpretation of Kossel-line patterns and an experimenta1 verification of the predicted orientation relationship of the cph k and fee a Cu-Si phases are presented. This orientation relationship can be described as (111)a, (00.1)k; [110]a [11.0]k. In addition, the lattice parameter of the a phase was found to he a. = 3.62154 ± 0.00014Å. The Kossel-line method when used in conjunction with electron microanalysis is shown to he capable of providing a complete chemical and structural analysis of a given crystal. THE most easily accomplished methods for determining the orientation of a single crystal are variations of the Laue X-ray diffraction method. Although certain materials can be oriented to within ± 1 deg accuracy by observation of exterior macroscopic features, such as etch pits, cleavage faces, or growth features, the Laue method is generally preferred for routine laboratory application. Both back-reflection and transmission patterns are coordinated by appropriate reference charts and are plotted in terms of reflection plane poles (normals) on a stereographic projection. Orientation is deduced by relating the pole distribution (which is fixed by the crystallographic symmetry of the specimen) to two specified external reference directions. The Laue method has several limitations. 1) Orientation can rarely be determined to better than ±l deg accuracy. Principal errors involve inaccuracy in specimen-to-film distance, measurement confidence of individual Laue spots, and stereographic plotting. 2) Because of the indeterminacy of the X-ray wave length diffracted to a given spot, it is not possible to determine supplementary crystallographic data, such as interplanar spacings and lattice parameters. 3) The method is generally limited to specimens of cubic symmetry or to specimens of high symmetry and known structure. 4) The relatively large cross-sectional area of the incident X-ray beam generally precludes the measurement of relative grain orientation in a polycrystalline material.* _____ Several of these limitations can be overcome by application of the Kossel-line method, which has been previously employed for precision lattice-parameter determinations.'-= For this method, a point source of divergent monochromatic X-rays is generated within the crystal by means of an incident electron beam. The divergent X-rays which fulfill the Bragg law are diffracted by the specimen and are recorded on a film placed either in transmission or back reflection. Analysis of the film yields a direct measurement of orientation and lattice-spacing values to an accuracy of ±1/2 pct. As analyses can be obtained from spherical specimen volumes as small as 50 µ in diameter, the method provides a means for structural analysis of second-phase or impurity precipitates within a given matrix. The primary limitation of the Kossel-line method is the requirement for an electron microanalyzer or similar apparatus capable of producing a finely focused electron beam. This paper is designed to present the theory, experimental procedure, and geometrical interpretation of Kossel patterns. The experimentally determined orientation relationship between the k and a phases occurring in the Cu-Si system and a precision measurement of the a lattice parameter are presented as a practical application of the method. THEORY OF KOSSEL LINES Divergent X-ray beam photography utilizes an effective point source of characteristic X-rays which, when diffracted from a single crystal, form numerous diffraction and absorption cones that are recorded on film.7 The cones generated from a source lying within the crystal are called Kossel lines.' Although the X-ray scattering from a divergent point source contained within a crystal is described in terms of Laue dynamical theory,9 the directions of the diffracted spectra can be ade-

Jan 1, 1965

By Y. Kondo, S. Yamazaki, Z. Asaki

Thermal deco7nposition of Pyrite particles in a fluidized bed with inert gas stream was studied. Assuming that heat transfer from the surroundings to the fluidized particles controls the overall decomposition rate, rate equations for the batch process and for the continuous process were derived. In the batch experiment, a linear rate equation satisfies the experimental results and the overall heat transfer coefficient calculated from the rate constant agrees fairly well with that obtained by Leva.l1 For the continuous process, two rate equations were derived, one on the assumption of complete mixing of particles and another on the upward piston flow of particles in a fluidized bed. The former holds for a bed containing a higher fraction of decomposed pyrite realized at lower feeding rates. The latter can be applied for a bed at higher feeding rates. Thus, segregation of particles in the fluidized bed was indicated at higher feeding rates. Bed temperatures also correspond to these conditions. ThERMAL decomposition of pyrite may be represented by Eq. [I]. The pressure of diatomic sulfur gas reaches 1 atm at about 690°C. The thermodynamics,' kinetics,2'3 composition, and properties3-5 of decomposed products of such a reaction have been studied. Pyrite is a very common sul-fide mineral and is often accompanied with other sul-fides. It is of basic interest in nonferrous metallurgy to clarify the behavior of pyrite in the pyrometallur-gical processes of sulfide minerals of metals such as copper, lead, zinc, nickel, and so forth. Interest in this reaction increased recently because of possible elimination of arsenic from pyrite in processing highly purified iron oxide pellets. Producing elemental sulfur from pyrite, instead of sulfuric acid, also aroused interest in this reaction. It is indicated that the thermal decomposition of solid particles, such as calcium carbonate, proceeds through three major sequential steps: heat transfer, interfacial chemical reaction, and mass transfer.637 It is known that the decomposed product of pyrite is very porous2, 3 and the diatomic sulfur gas evolved can easily escape through this layer of decomposed product. It depends upon the circumstances, therefore, whether the heat transfer to the interface within particles or the chemical reaction at the interface determines the overall decomposition rate. The enthalpy change in the decomposition of pyrite is about 33 kcal per mole FeS2 which is comparable to that of calcium carbonate. The decomposition of calcium car- bonate becomes more and more dependent on the rate of transport of heat when reaction temperature increases, such as occurs in a fluidized bed.6'7 It is reasonable to presume, therefore, that the thermal decomposition of pyrite, an endothermic process, carried out in a fluidized bed may be analyzed according to the heat transfer controlling model. This work intends, first, to propose a mathematical model that determines the overall rate in a fluidized bed for the decomposition process and, second, to investigate a few characteristics of the fluidized bed based upon the experimental results obtained. KINETICS OF THERMAL DECOMPOSITION IN A FLUIDIZED BED It is intended in this section to obtain rate equations for thermal decomposition of pyrite in a fluidized bed by assuming that the overall rate is determined by heat transfer from the surroundings to the particles. Both batch and continuous processes are considered. 1) Batch Process. To obtain the rate equation in the batch process, the following two additional assumptions are made. First, the temperature of preheated inert gas, tg, blown into the fluidized bed is assumed to be the same as the temperature of the fluidized bed, tf. Thus, no heat exchange occurs between the gas and particles in the bed and only the heat transfer from the reactor wall kept at tw to the particles is to be considered. Second, the decomposition is assumed to start at the outer surface of the particles and to proceed toward the center. At any given time during decomposition, undecomposed pyrite remains in the tori at a temperature: td. The decomposed shell is composed of FeS1+x whose outer surface is at tp Diatomic sulfur gas evolving at the interface is heated to tf during its escape through the decomposed shell. This is illustrated in Fig. 1. With the above-mentioned assumptions of heat transfer, we have:

Jan 1, 1969

By T. P. Floridis, J. H. Young

The need for close control of the phosphorus content of steels has led to numerous investigations on the equilibria of the dephosphorization reactions. Winkler and chipman1 have established the general conditions for effective dephosphorization of steel. They are high slag basicity, high oxygen potential, and low temperature. Other investigators have made additional contributions to the understanding of the dephosphorization process. The current status of the understanding of the dephosphorization of steel is concisely presented by Bodsworth2 and by Ward. The investigation reported in this communication was undertaken with the purpose of establishing the effect of additions of barium oxide and calcium fluoride on the dephosphorizing capacity of slags. Esin and Gel'd4 proposed that barium oxide, being more basic than calcium oxide, should cause an increase in dephosphorizing capacity when added to steelmaking slags, or when used as a substitute for calcium oxide. Derge5 has also proposed that in the future conventional slags might be replaced by BaO-Al2O3 slags. There is, however, no experimental evidence confirming the effect of barium oxide on the dephosphorizing capacity of slags. The effect of calcium fluoride on the dephosphorization of steel is not clearly understood. It is generally recognized that additions of calcium fluoride are beneficial. It is not clear, however, whether calcium fluoride affects the equilibrium of the dephosphorization reaction, or whether it simply causes an increase in the fluidity of the slag and, consequently, faster approach to equilibrium. The experimental procedure consisted in equilibrating synthetic molten slags with liquid copper at 1550°C under a gas stream containing argon, hydrogen, and water vapor. In all experiments the argon to hydrogen ratio was approximately 4:1, and the hydrogen to water ratio was 5.42:l. Molybdenum crucibles were used as containers for the slag and metal. Under the above-described conditions of temperature and composition of atmosphere, there was no observable attack of the crucibles by the metal, slag, or atmosphere. Copper was used instead of iron, because iron attacks molybdenum. The equilibration was made in a tubular furnace consisting of a recrystallized alumina tube. The alumina tube was heated by electrical resistance. A Pt-40 pct Rh wire winding was used for most runs. A silicon carbide tubular resistor was also used for some runs. Temperatures were measured with a Pt-Pt-Rh (10 pct Rh) thermocouple and kept constant within ±5°C. Equilibrium was approached from both sides, i.e., by adding the phosphorus either as oxide in the slag or as a phosphorus-rich alloy of phosphorus and copper. The holding time at the equilibrium temperature was 6 hr. At the end of each run the crucibles were rapidly cooled and removed from the furnace. The slag and metal were separated and analyzed. The experimental results are shown in Table I. The phosphorus content of the slag is expressed both as percent phosphorus pentoxide and as percent phosphorus. The basicity ratio is computed by dividing the number of moles of basic oxides-oxides of barium, calcium, magnesium, and sodium—by the number of moles of acidic oxides- oxides of aluminum, phosphorus, and silicon. Calcium fluoride is not included in the computation of the basicity ratio; i.e., calcium fluoride is assumed to be neither basic nor acidic. The distribution ratio of phosphorus—percentage of phosphorus in the slag divided by the percentage of phosphorus in the metal- is plotted in Fig. 1 against the basicity ratio. The results indicate that slags containing barium oxide have greater dephosphorizing capacity than slags containing calcium oxide. The high dephosphorizing capacity of slags containing sodium oxide and the low dephosphorizing capacity of magnesia-containing slags which already have been reported in the literature2 are confirmed by the results of this investigation. It appears that calcium fluoride has a beneficial effect on the distribution of phosphorus between slag and metal in acid slags only. Although the obtained distribution ratios between the phosphorus contents of slag and copper are not directly applicable to the dephosphorization of steel, they are sufficient for evaluating the effect of slag additions on the dephosphorizing capacity of slags in general. An increase in the ratio of distribution of phosphorus between slag and metal indicates lowering

Jan 1, 1968

By Arnulf Muan, Hobart M. Kraner

Ferromanganese alloys react with aluminu-silica brick in blast furnace hearths and cause the formation of new phases with low refractoriness and consequent failure of the refractory lining. The nature of these reactions is explained on the basis of petrographic observations, thermodynamic data, and Phase equilibrium considerations. Animproued hearth design resulted from these findings. The production of ferromanganese in blast furnaces presents many problems which are not encountered in the production of iron in the same furnaces. One of the most serious of these problems is the rapid failure of refractories caused by their reaction with the ferromanganese metal. The present paper describes such a "hearth attack", its symptoms, causes, and cure. Following an introductory discussion of operating practice in ferromanganese blast furnaces, results are presented of a petrographic examination of samples from a furnace which had to be shut down because of refractory failure. The causes of this failure are then analyzed on the basis of petrographic observations combined with thermodynamic and phase equilibrium data available in the literature. The latter type of data were subsequently used as a guide in recommending improvements in hearth designs which have since proven themselves successful in practical operations. I) FERROMANGANESE BLAST FURNACE PRACTICE It is considered good practice to blow in a furnace on iron and operate it in this way for a period of time preliminary to producing ferrornanganese. During this time, iron generally penetrates the bottom refractories six or more feet below the original working surface of the hearth. Not only does this metal pervade the joints to these depths, but the pores of the refractories are usually also filled by molten iron. The high throughput of the iron furnace provides ample heat to maintain a high temperature in the hearth refractories. This, together with a high ferrostatic pressure, causes porous clay brick of the hearth to shrink. During subsequent use of such a furnace in ferromanganese production, the iron in the pores of hearth brick if; replaced to some extent by ferromanganese. The replacement is usually not complete. This is probably due to the lower metal throughput and lower prevailing temperatures resulting from this in the brick of the hearth bottom. When the ferrornanganese furnace is banked—or when the temperature in the furnace falls due to a furnace delay—-manganese oxidizes even though the atmosphere is largely CO. Considerable expansion accompanies this oxidation of manganese from metal to oxide. The hearth refractories are then subjected to the disintegrating forces of the volume expansion. These forces may in extreme cases be large enough to lift the furnace off its mantle supports as was described in a previous paper.' When cooling takes place slowly, however, and the temperature remains at a fairly high level, the refractories undergo fluxing action by the MnO. This latter reaction and the reduction of SiO2 of the clay brick is the general subject of the present paper. The observations to be described herein were made on a ferromanganese furnace located at the Johnstown plant of Bethlehem Steel Co. The furnace was lined entirely with clay refractories and had operated on iron for 266 days and on ferromanganese for 96 days prior to being taken off because of a hearth wall failure. II) PETROGRAPHIC EXAMINATION AND CHEMICAL ANALYSIS The photograph reproduced in Fig. 1 shws a cross section of the upper part of an 18 by 9 by 4-1/2 in. bottom block removed from the blast furnace. This brick came from a depth of approximately 6 ft below the original working face of the bottom. It will be noted that the 4-1/2 in. dimension is almost the same as when the brick entered the furnace. Three characteristically different zones marked I, II, and III on the print of Fig. 1 are apparent. Results of chemical analyses of the original brick and samples from each of these zones are listed in Table I. Petrographically the various zones were characterized as follows: The central zone marked I was essentially un-reacted brick. The microstructure consisted of fine needles of mullite, and the pores in this entire area were filled with iron. This is characteristic of

Jan 1, 1962

By F. A. Forward, V. N. Mackiw

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting copper, nickel, cobalt, and sulphur from high grade nickel concentrate produced from Lynn Lake ores, and describes in some detail the chemistry of the process. IT is well known'.' 2 that copper, nickel, cobalt, zinc, ferrous iron, and a number of other metals combine with ammonia in aqueous solution to form complex ions of the form [Me(NH,)x]"+. The stability and solubility of these ions depend on the concentration of the metal ion in solution, on the amount of NH, present, and on the amount and type of anions present, e.g., OH-, C0;-, NO,, C1-, SO;-. If ammonia is partially or completely removed from such solutions, for example by boiling, the soluble ammines tend to decompose and the metals precipitate as basic salts. These properties of metal ammines have found practical application in the commercial recovery of copper, nickel, and cobalt from a variety of ores. In an operation formerly conducted at Kennecott"" the mill tailing containing 0.80 pct Cu as copper carbonate was leached by percolation with an ammonia-ammonium carbonate solution to dissolve the copper as the ammine. At Calumet and Hecla0-" With a mill tailing containing about 0.4 pct Cu as metallic copper, it has been found necessary to aerate the ammonia-ammonium carbonate leach solutions between stages to oxidize the solubilized copper. At Nicarol"-" where nickel and cobalt occur as oxides and silicates which are not soluble in ammonia, the ore is heated to decompose silicates and to selectively reduce the nickel and cobalt to metal, leaving the iron as Fe,O,, and is then leached with ammonia-ammonium carbonate solution accompanied by aeration to dissolve nickel and cobalt as ammines. In each of these leaching operations, the anion present is CO, and the metals can be precipitated from the leach solution as oxide (copper) or hydroxide and carbonate (nickel and cobalt) by boil- ing off NH, and C02 both of which are recycled to treat a subsequent ore charge. The products-—oxide, hydroxide, or carbonate—can be treated by conventional smelting, calcining, or electrolytic methods to convert them to refined metals. Thus the procedures mentioned utilize the properties of the ammines to extract copper, nickel, and cobalt from nonsulphide ores and separate them from the leach solutions. These processes have the advantage that they can be carried out in closed vessels at atmospheric pressure, that the leaching solutions are specific for the desired metals, that the metals can be recovered as relatively pure compounds by the boiling operation, and that the NH, and CO, can be recycled. Also, as the leach solutions after boiling and filtration are substantially free of metals, NH,, and CO,, they can be discarded, thus facilitating the control of the water balance in the leaching circuit. When, as is the case with Sherritt Gordon concentrates, sulphides are treated with ammonia solution in the presence of oxygen, the leach solution contains SO,--, and an entirely different set of conditions is encountered. The ammine sulphates (of nickel, for example) are more soluble than the carbonates and can be only partially decomposed by boiling. The SO, and NH, in the solutions can not be recovered by boiling. Thus, despite the more favorable leaching conditions resulting from high solubility of the ammine sulphates, the recovery of metals, NH,, and SO, from the solutions must be effected by other means. Sherritt Gordon Nickel Concentrate Treatment The Ni-Cu-Co flotation concentrate produced at Lynn Lake'" contains 12 to 16 pct Ni, 1 to 2 pct Cu, 0.2 to 0.5 pct Co, 33 to 40 pct Fe, 28 to 34 pct S, 8 to 20 pct insoluble, and less than 0.02 oz per ton precious metals. The nickel is present chiefly as pentlandite, the copper as chalcopyrite, and the iron as pyrrhotite and pyrite. Most of the cobalt is thought to be present in pentlandite, although it is known that a small amount occurs as Co-Ni-pyrite.

Jan 1, 1956

By A. R. Troiano, R. F. Hehemann

The influence of partial decomposition to high temperature bainite on reaction kinetics at a lower temperature has been studied in two alloy steels. Reaction at the lower temperature is retarded by the prior treatment, and the extent of decomposition may be reduced. Interpretation of these results is based on a mechanism involving a limitation in the nucleation and growth of bainite plates. OF the major transformations in steel, the characteristics and general behavior of the bainite reaction are probably the least understood and appreciated. Limitations of space preclude a critical evaluation of the present status of the bainite transformation in this presentation; however, such a treatment will shortly appear elsewhere. Only the salient features pertinent to the present investigation will be introduced briefly here. Although the reaction curve for the formation of bainite is similar to that for a nucleation and growth process, other kinetic features are more in keeping with the martensitic mode of transformation. A definite temperature exists above which austenite will not transform to bainite.1-5 his temperature, which has been designated B., is determined by the composition of the austenite. Unlike other nucleation and growth processes, the amount of austenite transformed to .bainite is a function of reaction temperature. The extent of decomposition increases from 0 at H. to 100 pct at some lower temperature.' , This lower temperature will be designated B1 and appears to be relatively insensitive to austenite composition.% 5 The similarity in the effect of reaction temperature on the bainite and martensite transformations serves to emphasize the close connection between these two decomposition processes. Austenite decomposition in the bainite range proceeds without partition of the alloying elements.8-11 Partition of carbon has been proposed" primarily on the basis that partial transformation to bainite lowers M, and increases the amount of austenite retained at room temperature. Carbon enrichment resuslting from such partition has been employed to explain the influence of reaction temperature on the extent of decomposition.'" It should be noted, however, that no enrichment has been detected experimentally in high carbon steels.1,14,15 Lattice-parameter measurements of retained austenite in steels containing 0.3 to 0.4 pct C have indicated carbon enrichment, 3,10-18 although the split indicative of a high carbon martensite has not been reported. Carbon enrichment, if it does occur, must be highly localized around the bainite plates. Therefore, carbon enrichment does not account for the influence of temperature on the progress of the bainite reaction."' Thermal history is known to influence the martensite transformation through stabilization.20,21 No similar phenomenon in the bainite transformation has been reported. Materials and Procedure Two triple-alloy steels were chosen for this investigation. Their compositions were as given in Table I. These steels were chosen because the pearlite reaction did not interfere with the bainite reaction. Steel K was received in the cast condition and forged from 2 in. square bars to 1/2 x1 3/4 in. plates. The 4340 was received as 11/4 in. hot-rolled rounds. Both steels were homogenized in vacuum for one week at 2300°F in order to minimize segregation. A quenching dilatometer similar to that described by Flinn, Cook, and Fellows" was employed for the kinetic measurements. Dimensional changes were detected by a differential transformer coupled with a high speed recorder. The dilatometer was mounted so that it could be transferred to any one of three furnaces: a nitrogen-atmosphere austenitiz-ing furnace and two salt-bath furnaces for isothermal transformation. Dilatometer specimens were 1/32 x 1/4x 1/2 in. with a gage length of 1.4 in. All specimens were nickel plated in order to minimize decarburization during austenitizing. The austenitiz-ing conditions consisted of 10 min at the temperatures given above. Austenitizing temperatures were controlled to 210°F and transformation temperatures to ±3ºF. The precision of the dimensional measurements was estimated to be ± 5 x105 in. per in. Results and Discussion Isothermal Transformation: The characteristics of the isothermal bainite reaction will be described

Jan 1, 1955

By T. M. Morris

A SEARCH of the literature reveals that no measurements have been made of the forces acting between a small solid particle whose surface is hydrophobic, and an air bubble to which the solid adheres, both immersed in water. Analyses have been made of the forces acting to support a greased solid on the surface of water, and the forces acting to cause a solid, whose surface is hydrophobic, to adhere to an air bubble in water. The latter analysis T. M. MORRIS, Junior Member AIME, is in the Department of Metallurgical Engineering and Mineral Dressing, School of Mines and Metallurgy, Rolla, Mo. New York Meeting, February 1950. TP 2734 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 16, 1949. This paper is the result of work done for part of a doctor's thesis at the Missouri School of Mines and Metallurgy. is often incomplete, however, because the internal pressure of the bubble has been neglected. It will be demonstrated that the internal gas pressure is not a negligible factor when dealing with bubbles of the size encountered in flotation. A study of the forces acting between an air bubble attached to a large flat surface is informative. It must be borne in mind, however, that this is not the condition present in a flotation cell, where the particle is small compared to the size of the bubble. The bubble is allowed to spread to its maximum contact angle on a large flat surface in the first case, whereas in the second case, the spread of the bubble is limited to the surface of the small particle which is presented to the bubble. Kabanov and Frumkinl studied the forces acting to cause adhesion of bubbles of hydrogen to a large surface of mercury, which served as an electrode in a dilute sulphuric acid solution. The force acting to hold the bubble to the mercury surface was found to be the vertical component of the surface tension between hydrogen and the sulphuric acid solution. The forces tending to cause the bubble to separate from the mercury surface were found to be: (1) the force exerted due to the internal pressure of the bubble acting upon the area of contact between the bubble and the mercury surface, and (2) the buoyant force of the bubble minus the hydrostatic force acting at the base of the bubble. These investigators photographed bubbles that were just on the verge of separating from the mercury surface. From these photographs, they measured the contact angle between the mercury surface and the tangent to the hydrogen-solution interface at the point of contact between bubble and mercury surface. They calculated the volume of the bubble and the internal pressure of the bubble. The equivalence between the upward acting and downward acting forces was remarkable. Wark2 pursued an investigation similar to that of Kabanov and Frumkin, and at the same time. His deductions verified those of Kabanov and Frumkin. He also considered the conditions present in flotation and was aware of the effect of the internal pressure of the bubble. Further, he proposed several conditions under which a small solid particle would adhere to an air bubble in water. In 1922, Edser," an English physicist, made the following statement. "It must be remembered that no particle could float stably, but for the possibility of variation of the contact angle, for if this were a constant, a slight tilt would inevitably cause the particle to sink." Wark criticized this statement, maintaining that the contact angle does not vary. The experimental data to be presented indicates that Edser was correct. Experimental Procedure: Briefly, the experimental procedure was as follows. A bubble of air was generated in distilled water. A rod of known diameter, one end of which was water repellent, was attached to this bubble. The weight of the 'rod was measured. The internal pressure of the bubble was measured with a manometer. The hydrostatic head from the surface of the water to the bottom of the rod was measured. The angle between the horizontal projection of the end of the rod and the tangent to the bubble at the circle of contact be-

Jan 1, 1951

By T. M. Morris

A SEARCH of the literature reveals that no measurements have been made of the forces acting between a small solid particle whose surface is hydrophobic, and an air bubble to which the solid adheres, both immersed in water. Analyses have been made of the forces acting to support a greased solid on the surface of water, and the forces acting to cause a solid, whose surface is hydrophobic, to adhere to an air bubble in water. The latter analysis T. M. MORRIS, Junior Member AIME, is in the Department of Metallurgical Engineering and Mineral Dressing, School of Mines and Metallurgy, Rolla, Mo. New York Meeting, February 1950. TP 2734 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 16, 1949. This paper is the result of work done for part of a doctor's thesis at the Missouri School of Mines and Metallurgy. is often incomplete, however, because the internal pressure of the bubble has been neglected. It will be demonstrated that the internal gas pressure is not a negligible factor when dealing with bubbles of the size encountered in flotation. A study of the forces acting between an air bubble attached to a large flat surface is informative. It must be borne in mind, however, that this is not the condition present in a flotation cell, where the particle is small compared to the size of the bubble. The bubble is allowed to spread to its maximum contact angle on a large flat surface in the first case, whereas in the second case, the spread of the bubble is limited to the surface of the small particle which is presented to the bubble. Kabanov and Frumkinl studied the forces acting to cause adhesion of bubbles of hydrogen to a large surface of mercury, which served as an electrode in a dilute sulphuric acid solution. The force acting to hold the bubble to the mercury surface was found to be the vertical component of the surface tension between hydrogen and the sulphuric acid solution. The forces tending to cause the bubble to separate from the mercury surface were found to be: (1) the force exerted due to the internal pressure of the bubble acting upon the area of contact between the bubble and the mercury surface, and (2) the buoyant force of the bubble minus the hydrostatic force acting at the base of the bubble. These investigators photographed bubbles that were just on the verge of separating from the mercury surface. From these photographs, they measured the contact angle between the mercury surface and the tangent to the hydrogen-solution interface at the point of contact between bubble and mercury surface. They calculated the volume of the bubble and the internal pressure of the bubble. The equivalence between the upward acting and downward acting forces was remarkable. Wark2 pursued an investigation similar to that of Kabanov and Frumkin, and at the same time. His deductions verified those of Kabanov and Frumkin. He also considered the conditions present in flotation and was aware of the effect of the internal pressure of the bubble. Further, he proposed several conditions under which a small solid particle would adhere to an air bubble in water. In 1922, Edser," an English physicist, made the following statement. "It must be remembered that no particle could float stably, but for the possibility of variation of the contact angle, for if this were a constant, a slight tilt would inevitably cause the particle to sink." Wark criticized this statement, maintaining that the contact angle does not vary. The experimental data to be presented indicates that Edser was correct. Experimental Procedure: Briefly, the experimental procedure was as follows. A bubble of air was generated in distilled water. A rod of known diameter, one end of which was water repellent, was attached to this bubble. The weight of the 'rod was measured. The internal pressure of the bubble was measured with a manometer. The hydrostatic head from the surface of the water to the bottom of the rod was measured. The angle between the horizontal projection of the end of the rod and the tangent to the bubble at the circle of contact be-

Jan 1, 1951

By G. C. Rauch, T. H. Courtney, J. Wulff

The superconducting behavior of Nb-Ti alloys containing 40 and higher wt pct of Nb and variable oxygen content was studied as a function of thermomechanical processing. Critical current density (Jc) us applied transverse magnetic field (H) data were obtained for 0.010 in. diam wires at 4.2° Kin steady fields up to 120 kOe. The precipitate responsible for increase in Jc in each of the alloys studied was related to niobium and oxygen content. In alloys containing 40 to 60 wt pct Nb with less than about 1600 ppm of oxygen, w precipitation in the range 350° to 450°C appears to be responsible for the maximum value of Jc observed. In alloys of higher oxygen content (-2500 ppm), the oxygen-enriched a phase which precipitates in the temperature range 450° to 550°C is a more effective fluxoid pinner. Maximum Jc in low oxygen (350 ppm) 80 wt pct Nb alloys was achieved by 600°C aging heat treatments. Measurements of resistive critical field also reflect the changes in composition accompanying precipitation in these alloys. It is well known that the superconducting critical current density, Jc, of solid solution superconducting alloys can be increased by precipitation heat treatments.1-4 The precipitate, to serve as an effective superconzlucting fluxoid pinner and increase Jc, must be of proper size and spacing.' Its electronic properties must also be different from those of the matrix.6 As in age-hardenable systems, optimum temperature and time of aging are dictated by the composition and history of the particular solid-solution alloy under consideration. The alloy diagram of Ti-Nb7-9 shown in Fig. 1 is typical of ß-stabilized Ti alloys. Precipitation to achieve high Jc in Ti-Nb and Ti-Ta alloys is usually carried out in what is believed to be a two-phase a + ß region.1,2,4,10 Previous work on Ti-Nb4,11 and on other ß-stabilized systems such as Ti-V, Ti-Mo,12-14 has shown, however, that the first precipitate to appear is not necessarily (Y. Under specific conditions the meta-stable w phase is precipitated instead. A further complication arises in such alloys from the strong influence of contained oxygen on the phase stability and on the kinetics of precipitation.15,16 The superconducting critical current density of Nb-Ti alloy containing less than 36 wt pct Nb has been studied by Vetrano and Boom1 and Kramer and Rhodes.4 The most effective aging temperature was found to be about 425°C; fluxoid pinning was attributed to the precipita- tion of a by Vetrano and Boom and of w by Kramer and Rhodes. Although the latter workers used recrystal-lized material and the former cold-worked, studies carried out in our laboratory lead us to believe that the type of precipitate responsible for increased Jc is unaffected by prior cold-work.17 That other types of precipitates may also be effective, especially in higher oxygen-containing alloys, has been demonstrated by Reuter, et al.2 in this laboratory with the aid of electron microscopy. Reuter et al. found that at an aging temperature of 600°C, fee-TiO is precipitated, resulting in high values of Jc. Even higher values of Jc were observed after heat treatment at 500°C, but the precipitate could not be indexed as fee-TiO. Whether the precipitate was oxygen-rich w or a could not be clearly distinguished. The work nevertheless indicates that appreciable amounts of oxygen alter the nature of the phases precipitated at different temperatures, at least in alloys containing more than 36 wt pct Nb. Since such compositions are more readily worked into suitable wire than lesser niobium content alloys, it was decided to study the response to aging of the alloy compositions reported in the present paper with the hope of clarifying the effect of composition on the precipitation processes responsible for high values of Jc. I. EXPERIMENTAL Nb-Ti alloys containing 40, 50, 60, and 80 wt pct Nb were prepared by are-melting 35 g ingots of iodide crystal bar titanium and electron-beam melted niobium.

Jan 1, 1969

By C. J. Leith

A study of the effect of rock composition, rock structure and degree of weathering on the stability of cut slopes is being sponsored jointly by the U.S. Bureau of Public Roads and the North Carolina Highway Commission. In 58 mountain and piedmont counties of North Carolina the percentage of failed cut slopes is greatest in micaceous metasediments, gneisses, and schists, and in saprolite and soil derived from these rock types. Soil slope failures outnumber rock slope failures by two to one. Joints and similar planes of separation exert a strong influence on size and shape of the sliding mass. They may or may not act as failure surfaces, depending on their orientation with respect to the active forces. Climatological data, though indicative of weathering conditions, do not correlate well with slope failure frequency. Because of the presence of joints and similar planes of weakness in soil and rock materials, conventional methods for analyzing slope stabilities are not directly applicable. Empirically derived modifications of these methods are being investigated. A study of the stability of highway cut slopes, sponsored by the U. S. Bureau of Public Roads and the North Carolina State Highway Commission, began in 1962 at North Carolina State of the University of North Carolina at Raleigh. As part of this study all slides, rockfalls and other types of cut slope failures on Federal and State highways in the 58 mountain and piedmont counties in North Carolina were located and described, and the data catalogued in a punched card file system. A major objective of the project is to relate slope failures to properties and physical conditions of the geological units in which the slopes were constructed, and to correlate soil type and/or geological unit with type and frequency of slope failure. The complexities of the problem of slope stability and the limitations which these complexities impose on methods for analyzing slopes have been recognized for many years. A great variety of factors and processes may lead to slides, often making it almost impossible to analyze theoretically the conditions required for stability of slopes. One of the principal factors determining maximum safe slopes is the shear strength of the material in which the slopes are cut, but unfortunately there are very few data available concerning shear strengths of residual soils. Vargasl tested clay derived from gneiss and granite in southern Brazil; the properties of decomposed granite occurring near Hong Kong were determined by Lumb.2 These data are being used, when applicable, to supplement the test data obtained in the present study by Yorke.3 The locations of the North Carolina slope failures, more than 400 in number, are shown on Fig. 1. This map, adapted from the Geological Map of North Carolina,4 suggests the possibility of a relationship between frequency of slide occurrence and rock type. However, the evaluation of this possibility requires consideration not only of the type of rock, but also of its large and small scale structural features, its susceptibility to and degree of weathering, and the composition and structure of the weathering products. Soil slope failures in thoroughly weathered soil material and saprolite outnumber rock slope failures two to one. INFLUENCE OF ROCK TYPE The agricultural soil type involved in each soil slope failure was identified and each failure was catalogued in terms of the parent material from which the soil was derived. These data indicate that most of the slope failures, whether in the rock or in the derived soil, are associated with metamorphic rocks (see Fig. 2a). The data may be skewed somewhat because of the relative sizes of the total areas underlain by the various rock types, but Leith and Gupton5 have demonstrated that the preponderance of failures in metamorphic rocks is of much greater magnitude than could be accounted for by the areal factor alone. The dominance of metamorphic rocks is emphasized when soil slope failures are considered in terms of the specific rock types from which the soils were derived (see Fig. 2b). In particular, mica schists and mica gneisses account for more slides

Jan 1, 1965