Search Documents

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

By F. G. Smith

A FEW years ago, the writer encountered a, problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Matthewson and Phillips, an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-inn. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures.

Jan 8, 1919

L50 Adirondack L1 Alaska L2 Arizona L58 Arkansas L66 Billings Petroleum L3 Black Hills L4 Boston L5 Carlsbad Potash L6 Central Appalachian L60 Central New Mexico L7 Chicago L8 Cleveland L9 Colorado L57 Colorado Plateau L10 Columbia LII Connecticut L55 Dallas L12 Delta L65 Denver Petroleum L13 Detroit L14 East Texas L15 El Paso Metals L71 Evangeline L45 Florida L54 Fort Worth L16 Gulf Coast L61 Hobbs L62 Hugoton L68 Illinois Pet Basin L17 Kansas L18 Lehigh Valley L52 Lou-Ark L47 Mexico L19 Mid-Continent L20 Minnesota L56 Mississippi L21 Montana L22 Nevada L64 Niagara Frontier L23 New York L67 New York Petroleum L25 North Pacific L24 North Texas L26 Ohio Valley L27 Oklahoma City L28 Oregon L63 Panhandle L29 Penn -Anthracite L30 Permian Basin L51 Peru L31 Philadelphia L32 Pittsburgh L33 St Louis L34 San Francisco L59 San Joaquin L35 Southeast L36 Southern Calif L69 Southern Calif Pet L53 South Plains L37 Southwest Texas L48 Southwest Alaska L38 Southwest N Mex L44 Spindletop L39 Tri-State L40 Upper Peninsula L41 Utah L70 Venezuela L42 Washington, D C L43 Wyoming L49 West Central Texas L46 Philippine

Jan 1, 1956

By John Boardman

THE latest metal-mine accident report available for the United States is that of the Bureau of Mines for the calendar year 1919. Quoting from Table 20, p. 53, of that report, we find that there were 468 men killed, 7 permanently totally disabled, 321 permanently partially disabled, 7848 injured seriously (more than 14 days disability), and 23,330 of 1 to 14 days disability. We have no records to show what the average days lost per case of accident is, but the records for the Anaconda Copper Mining Co. show that, leaving out the fatalities and total permanent disabilities, and counting those in which the lost time was one or more days, the actual days lost due to accidents, for the Butte mines and shops for five years, 1917-1921, were as follows: Accident Statistics, Butte Mines and Shops of A. C. M. Co. Rate Shifts Days Lost Year Accidents Total Shifts 10,000 Shifts Days Lost Per Acci-dent 1917 2,661 3,169,720 8.395 26,734 10.05 1918 2,765 3,545,149 7.799 39,199 14.17 1919 1,381 1,853,143 7.452 22,797 16.50 1920 1,376 1,879,410 7.321 20,164 14.65 1921 376 776,461 4.842 8,287 22.03 Total... 8,559 11,223,883 7.625 117,981 13.80 In order to place an economic value. on this loss, we will assume that all the 468 fatalities and the 7 total permanently disabled in the United States were com-pensated for at the rate which applies in the State of Montana, that is, $5000 each, and that the 8169 serious accidents in the United States were compensated for at an average of $70 per case, thus bringing the estimated compensation paid by metal-mining companies in the United States to the enormous total of $2,946,830 for the year 1919. The figure of $70 per case was obtained by dividing the total amount paid by metal-mining companies under Plan No. 1 of the Montana Compensation Law, for the first five years of its operation, by the total number of serious accidents for those years.

Jan 9, 1922

Adolph Greiner, Seraing, Belgium:—I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have corrected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent. was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix 11. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p. in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. Tom WEstGarth, Middlesbrough, England :—My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by British engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have become quite ordinary motors for a good many purposes. It was at first thought that gas-engines were troublesome, and ill-

Jan 1, 1907

By AIME AIME

LOCAL COMMITTEES. GENERAL RECEPTION COMMITTEE.-Mr. and Mrs. H. S. Chamberlain, Mr. and Mrs. J. T. Lupton, Mr. and Mrs. T. H Lasley, Mr. and Mrs. R. S. Faxon, Mr. and Mrs. H. Clay Evans, Mr. and Mrs. C. E. James, Mr. and Mrs. B. F. Thomas, Air. and Mrs. H. S. Probasco, Mr. and Mrs. W. M. Lasley, Mr. and Mrs. L. W. Llewellyn, Mr. and Airs. T. G. Montague, Mr. and Mrs. E. B. Thomasson, Mr. and Mrs. C. F. Milburn, Mr. and Mrs. C. A. Raht, Mr. and Mrs. C. C. Notting¬ham, Mr. and Airs. Z. C. Patten, Mr. and Mrs. Willard Warner, Mr. and Mrs. S. R. Read, Mr. and Mrs. Carl White, Mr. and Mrs. M. M. Allison, Air. and Mrs. C. E. Buck, Mr. and Airs. H. F. Temple, Air. and Mrs. M. M. Hedges, Mr. and Airs. X. Wheeler, Mr. and Airs. John A. Patten, Air. and Airs. N. T. Montague, Mr. and Mrs. R. H. Williams, Mr. and Mrs. T. R. Preston, Mr. and Airs. Morrow Chamberlain, Mr. and Airs. T. C. Thompson, Mr. and Airs. T. L. Montague, Mr. and Mrs. O. L. Hurlbut, Air. and Mrs. C. A. Lyerly, Mr. and Mrs. Garnett Andrews, Air. and Mrs. M. B. Ochs, Mr. and Airs. Webster James, Mr. and Mrs. D. P. Montague, Mr. and Mrs. Z. C. Patten, Jr., Mr. and Mrs. W. A. Sadd, Mr. and Mrs. J. B. Pound, Air. and Mrs. George D. Lancaster, Air. and Airs. J. F. Johnston, Mr. and Mrs. R. W. Barr, Air. acrd Mrs. W. B. Davis, Mr. and Airs. Douglas Baxter, Air. and Mrs. W. R. Crabtree, Mr. and Mrs. Lewis M. Coleman, Mr. and Mrs. Newell Sanders, Mr. and Mrs. E. Y. Chapin, Mr. and Mrs. W: B. Riddell,. Mr. and Mrs. J. B. Frazier, Mr. and Mrs. John A. Moon, Mr. and Mrs. C. D. Mitchell, Dr. and Airs. J. H. Race, Mr. and Airs. A. W. Chambliss, Mr. and Mrs. J. P. Smartt, Mr. and Mrs. J. F. Tarwater, Mr. and Mrs. L. D. Drewry, Capt. and Mrs. A. B. Putnam, Mrs. Minnie C. Ewing, Mr. G. F. Meehan, Mr. Sam S. Gerstle, Mr. P. A. Brawner, Mr. C. M. Preston, Air. George M. Guild, Mr. L. M. Mansfield, Dr. J. W. Johnson, Dr. J. AI. Hogshead. EXECUTIVE COMMITTEE.-H. S. Chamberlain, Chairman; H. S. Probasco, C. M. Preston, H. Clay Evans, J. T. Lupton, M. B. Ochs, C. C. Nottingham, Al. Al. Alli¬son, R. S. Faxon, C. E. James, C. A. Raht. EXCURSION TO CHICKAMAUGA PARK.-T. C. Thompson, Chairman; B. F. Thomas, G. F. Meehan, Morrow Chamberlain, W. J. Bass, J. K. McGoodwin. EXCURSION TO HALES BAR LOCK AND DAM.-R. H. Williams, Chairman; John A. Patten, Newell Sanders, George M. Guild, Capt. A. B. Putnam. EXCURSION TO ROCK-WOOD.-F. H. Clymer, Chairman; T. L. Brown, T. A. Wright, J. P. Tarwater, T. L. Peterman. INSTITUTE HEADQUARTERS.-The Hotel Patten. THE first session, held Thursday evening, Oct. 1, in the Banquet Hall of the Hotel Patten, was called to order by Capt. H. S. Chamberlain, Chairman of the Local Committee, who, in behalf of the city of Chattanooga, extended a hearty welcome to the members and guests of the Institute.

Nov 1, 1908

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By Kirtley F. Mather

FROM almost every point of view, petroleum was "strategic mineral number one" during the World War that ended in 1945. Even the spectacular advent of the atomic bomb in the final days of the conflict did not displace it from its position of prime importance, although within a few years uranium will almost certainly be the "number one" material in the minds of military strategists, if it is not even now in that position. But both as fuel and as raw material for chemical industries, petroleum will hold the center of the stage for many years to come. Hardly any other substance illustrates so fully the manner in which science and technology may be combined to achieve the utmost success in contributing to human efficiency and comfort. Fundamental to any understanding of the problems implied by my topic

Jan 1, 1948

By SAM YOUR

PROCESSING, technology and application of non- ferrous metals-copper, lead, zinc, aluminum, nickel, precious metals, foundry metallurgy, less common metals, secondary metals-are the special field of the Institute of Metals Division. New developments in this field during 1930 are more or less briefly out- lined in this review prepared by the papers and publications committee of the Institute of Metals Division as follows:

Jan 1, 1931

By Richard J. Robbins

Mechanical moles have developed through a tedious process of evolution. At times it has seemed that tunnel borers have been subject to the same Darwinian rules of evolution as their zoological namesakes who, despite their efficiency, are highly specialized and still restricted to soft soil conditions near the surface of the ground. HISTORICAL HIGHLIGHTS The Robbins Co. began its work in this field in 1947 with the development of a twin-bore continuous coal miner. Although these machines were used primarily in coal, two of the early prototypes were used to bore tunnels through shale. Disk cutters were first used on these machines and showed promising results as core breakers between drag-bit kerfs. In 1953, James S. Robbins and Assocs. undertook the development of a 25-ft 9-in.-diam circular tunnel borer for Mittry Construction Co. to be used at Oahe Dam in South Dakota (Fig. 1). This is believed to be the first rock tunnel-boring machine built since the end of the 19th century when short sections of the Channel tunnel were successfully bored in chalk from both the English and French shores. Another Oahe Dam machine was built in 1955, and then a series of three small-diameter machines for the company's first real experience with medium-hard and hard rock (Fig. 2) None of these three could be considered a success, although they laid the groundwork for the success that followed. Interbedded shale and limestone in Pittsburgh and hard limestone in Chicago quickly pointed up the weaknesses in these machines which were used by Perini, Dravo, and Healey. Among the problems were the high breakage rate of tungsten-carbide drag bits, too much flexibility in the drive shafts, failure of high-pressure hydraulic systems, chain-conveyor failure, and general lack of rigidity and strength. In 1956 another attempt at medium-hard and hard rock-boring proved this time to be a success and a significant turning point in the development

Jan 1, 1970

By Frank G. Snyder

The Precambrian of Midcontinent United States includes a metamorphic belt of probable Middle Precambrian age, a belt of Keweenawan volcanics and sediments, and widespread igneous activity that extended from Iowa to Texas. Most of the present structural configuration of the Midcontinent was developed by epeirogenic movements during the Paleozoic. The dominant elements are basins and arches. Three major metallogenic provinces occur in the Midcontinent. They include the Missouri Precambrian iron ores, the Lake Superior copper ores, and the Mississippi Valley lead-zincbarite- fluorite deposits. Several large iron deposits, occurring in rhyolite and andesite host rocks, are known. Both discordant massive bodies and replacement- type bodies occur. The iron deposits are believed to have been formed during the period of igneous activity. They are essentially the same age as the volcanics and older than the granites that intrude the volcanics. The Lake Superior copper ores include two established districts, the Keweenawan district and White Pine, and the copper-nickel deposits in the Duluth gabbro. The lead-zinc-barite-fluorite deposits include four major districts, Southeast Missouri, Upper Mississippi Valley, Tri-State, and Illinois-Kentucky, and at least eight minor districts. Ore may occur in stratiform deposits and in veins. The major districts all contain stratiform deposits, but several have produced appreciable quantities of vein ore. Only vein deposits are known in some of the smaller districts. The major features of all districts can be catalogued in terms of host rocks, structural patterns of districts, types of ore-bearing structures, and mineralogical characteristics. From these features, a Mississippi Valley type ore body, in its type area, can be defined.

Jan 1, 1968

By AIME AIME

DATA in this report enable comparisons to be made within the bituminous coal industry and comparison as well with copper and steel in respect to capacity and overdevelopment. The conclusions reached from the data will tend to correct numerous current misconceptions. The data have been prepared by various members of the Coal and Coke Committee of the A.I.M.E., from the most authentic sources avail¬able, and cover the period 1913-1924 wherever possible. CAPACITY AND OVERDEVELOPMENT Table 1 shows statistics for the industry, mainly from the U. S. Geological Survey sources, but partly from the U. S. Coal Commission reports. The mine capacity with equipment and labor as of given date is calculated for each state by obtaining the total man days worked as reported by the operators, and dividing this figure into the total production, getting the production per man day; this figure times the number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method-one that the total number of men employed is used instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. Covering the first, the same number of men is used in estimating capacity as is used in actual production, and this condition exists at all times. Regarding the second, the opinion is general among coal men that 280 days is as great a figure as should be used, as it is practically impossible to keep any mine working full time at the same daily rate as when it is working part time. The capacity, as estimated on this basis, is much more nearly the true capacity, although even with present railroad efficiency this amount of coal could not be moved.

Jan 1, 1926

By Robert M. Grogan, James C. Bradbury

The Illinois-Kentucky mining district has, since 1880, accounted for 80 per cent of all U.S. production of fluorspar. The ore deposits are of two types: vein deposits formed by fissure fillings along faults and bedding-replacement deposits formed by the replacement of strata at certain favored stratigraphic positions along minor faults and fractures. Fluorite is the chief valuable mineral in the deposits. Sphalerite and galena commonly are present in small amounts but, in some ore bodies, may form a substantial part of the valuable constituents of the ore. Calcite is the chief gangue mineral; quartz and barite Exposed strata range from Devonian are present in various amounts. through Pennsylvanian in age. Igneous intrusive rocks occur as mafic dikes and sills and intrusive breccia dikes and plugs. Structurally, the district is situated on a generally northwest- trending arch that has been sliced into a series of long, narrow blocks by normal faults that trend northeastward. The structural The localization of the ore deposits by faults and fractures, the association of fluorite mineralization with intrusive breccias, and various lines of petrographic and geochemical evidence indicate that the fluorite-zinc-lead deposits were epigenetic and deposited by solutions emanating from a deep alkalic magma.

Jan 1, 1968

[Aase, Qlenn D., (Junior Member '40) Jr. Met.. American Smelt. & Refin. Co., Selby. Calif. Abadie, Henry G., (Junior Member '43) Petr. Engr.. Avenal, Calif. Abbott, Clarence E., (Member '04) Civil En=.. V.P.. Tennessee Coal. Iron & R.R. Co., 1542 Brown biarx Bldg.. Birminpham, Aln. Abbott. Fred E., Jr., (Member '44) Petr. Engr., C/O Arabian Anierican Oil Co.. A.P.O. 816. c/o Postmaster, New York, N. Y. Abel, Raymond L., (Member '28) Chem. Engr.. C. O., Pittsburgh Chem. Warfare Procurenlent Dist.. American Bank Bldg., Pittsburph. Pa. Abel, Walter D., (Member '32) Min. Engr.. Supvr. Engr.. RFC, Los Angeles, Calif.]

Jan 1, 1946

By Robert H. Richards

Tuns truly remarkable machine was built on a preliminary scale in May, 1895. The first full-sized table was built by Mr. A. R. Wilfley, and was used in his own mill in Kokomo in May, 1896. The first table sold for installation was placed' in the Puzzle mill, Breckinridge county, in August, 1896. The mill enthusiasts at first hailed it as the cure for all the ills that flesh is heir to in the milling line. A little later it was found to make losses which were serious, and on this account the table succeeded only to a limited extent in displacing the vanners of the gold-mills. Still later, mill-men in a number of districts throughout the country made special studies of the faults of the machine, and devised a number of ways of grouping supplementary machines to overcome as far as possible the losses, and at the same time retain the benefit of the extraordinarily large capacity accompanied by the production of clean concentrates for which the machine has become so justly famous. I hope to make an exhibit of some of these methods in an appendix to my book on ore-dressing which is now in preparation. These experimenters have not written up the subject, and if they possess all the facts they have not given them out for the benefit of the mining profession at large. The object of this paper is to obtain the facts and to pre¬sent them so clearly that their bearing can be seen by all. To this end two complete series-'of tests have been planned. One (the present paper), to study concentration of galena in presence of quartz; the other (to follow shortly), to study concentration of chalcopyrite in presence of quartz. Some authorities claim that the table does its best work when treating natural products; by this phrase I mean products which have been crushed to pass through a limiting

Jul 1, 1907

A dinner was given to Ambrose Swasey by the United Engineering Society, at the Engineers' Club, on November 14. Those present -included -twenty-one presidents and past presidents of the Founder Societies. Charles F. Rand, President of United Engineering Society, presided. President Robert S. Woodward, of the Carnegie Institution of Washington, and Dr. Robert W. Hunt, of Chicago, made addresses to which Mr. Swasey responded. Dr. Michael I. Pupin, Chairman of Engineering Foundation, made the closing address. The evening was marked by the high character of the addresses, inspiration for grave duties lying before the engineering profession, and by the spirit of good fellowship. Among the seventy-two persons present were the following members of the Institute: E. E. Bartlett, William N. Best, J. Parke, Channing, C. R. Corning, F. C. Cottrell, J. V. Davies, J. V. N. Dorr, H. S. Drinker, Karl Eilers, H. M. Howe, A. C. Humphreys, Robert W. Hunt, Wm.. B. Jackson, D. S. Jacobus, J. H. Janeway, J. E. Johnson, Jr., John Johnston, George F. Kunz, Edwin Ludlow, Philip N. Moore, Fred'k. H. Newell; Wm. H. Nichols, H. Hobart Porter, Charles F. Rand, R. M. Raymond, .Jesse M. Smith, E. Gybbon Spilsbury, Bradley Stoughton, . Joseph Struthers, Benj. B. Thayer, Wm. H. Wiley, S. T. Wellman.

Jan 1, 1919

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water -by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other, adsorbent earths.

Jan 1, 1929

By H. O. HOPMAN

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. THE substance of this paper was prepared for the Seventh International Congress of Applied Chemistry, held in London, May, 1909, under the title, Some Developments in Blast-Roasting. In the absence of the author, a -short abstract of the paper was read, and the abstract only will appear in the proceedings of the congress. The present paper has been partly rewritten and considerably enlarged by information gained since the original was prepared ; also some illustrations have been added. Blast-roasting' is a generic term for the process of forcing air through finely-divided. metallic sulphide with the object of roasting and agglomerating in a single operation. At first the process was confined to a galena-concentrate ; lime, limestone, or gypsum was added, to serve both as a diluent to keep separate the particles of galena that they might be thoroughly oxidized, and as a flux that the partly-roasted ore might be agglomerated by the formation of some slag. Later it was extended to treat other metallic sulphides. The leading processes were the Huntington-Heberlein and the Savelsberg of Europe, and the Carmichael-Bradford of Australia. In the United States and Canada, the Huntington-Heberlein process has found application in some instances with galena-concentrates, for which it was originally intended; but this class of ore is not often treated alone, hence the process has had to be modified to suit conditions. The Savelsberg process has been transplanted to this country in about its original form. The Carmichael-Bradford is not used at present. The changes called for in the Huntington-Heberlein process to adapt it to the class of lead-bearing ores usually smelted have been the 1 A. S. Dwight, Engineering and Mining Journal, vol. lxxxv., No. 13, p. 649 (Mar. 28, 1908).

Jun 1, 1910

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

At very low concentrations, carbon dissolves interstitially in molybdenum resulting in a linear expansion of lattice parameter with increase of carbon in solid solution. Geometrical consideration of the relative size of carbon atom to size of interstice approximately predicts the observed volume expansion. THE element carbon, occurring in molybdenum, either as an unavoidable impurity, or purposely added, markedly affects the mechanical properties of molybdenum. Several investigators1-" have noted the occurrence of molybdenum carbide at the grain boundaries of cast molybdenum, and Fischer and Rengstorff' have shown that this intergranular constituent can induce intergranular brittleness. The appreciable change, with temperature, of the solid solubility of carbon in molybdenum, found by Few and Manning," suggests other important effects upon mechanical properties. Finally the relative atom diameters of carbon and molybdenum (the ratio of atom diameters is 0.59) are indicative, by analogy with iron (ratio of carbon atom diameter to iron atom diameter is 0.65), of a possible interstitial solid solution. If carbon dissolves intersti-tially in molybdenum, anelastic effects and age-hardening effects, similar to those observed in other body-centered cubic metals, could be expected. However, from the work of Sykes, Van Horn, and Tucker," it might be inferred that carbon forms only a substitutional solid solution with molybdenum. These considerations made it desirable to study the effect of carbon on the lattice parameter of molybdenum in greater detail than heretofore. All heat treating was done in a high temperature furnace7 built specifically for heat treatment of molybdenum. The temperatures and times of heat treatment were determined from the a solubility limit for the Mo-C system." These heat treatments were carried out in argon which was purified with respect to N, and H.!0." Purification of the argon was accomplished by passing the argon over hot (750°C) titanium and then through a magnesium perchlorate drying tower. As many as six samples were run concurrently and quenched at different times without interrupting the furnace cycle. Both the purity of the furnace atmosphere and ability to quench samples from any temperature up to 4000 °F were of prime importance in the successful heat treatment of samples for the lattice parameter investigation. Carbon Analysis The Leco Combustion apparatus was used for carbon analysis. This apparatus is capable of an accuracy of & 0.003 pct for a 1 g sample in the range below 0.10 pct. However, it is felt the degree of accuracy is somewhat better than this limit in view of the consistency evident by cross checking a number of determinations. The Battelle Analytical Laboratory consistently reported check results to within k 0.001 pct C. X-ray Measurements The molybdenum wire specimens (20 mils) were carefully filed down to about 12 mils and then etched with nitric acid to 8 mils. Carbon analyses were made on specimens before reduction in size; however, since there was no evidence of surface carburization, it is probable that the carbon was uniformly distributed throughout the sample. The resultant specimens were strain free and small enough to minimize the error in the lattice parameter determinations due to X-ray absorption. Diffraction patterns were obtained with a Debye-Scherrer powder camera 114.59 mm in diam utilizing the Straumanis type asymmetrical film mounting. Nickel-filtered copper. Ka radiation and zirconium-filtered molybdenum Ka radiation were used. Line positions on the film were measured with a traveling microscope equipped with a vernier scale permitting measurement to 0.001 cm. The average of five readings was used to determine the position of each line. The lattice parameter for each specimen was determined from the data by the extrapolation method of Bradley and Jay, Y.e., the intercept at 90" of the straight line obtained by plotting the apparent lat-

Jan 1, 1953

ASHBEL WELCH, Lambertville, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and should not be overlooked,—the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destfoyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were muqh the most rapidly destroyed. It is doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de-

Jan 1, 1881