Search Documents

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

By A. A. Smith, J. S. Smart

THE elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses, When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range 0 to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorily determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing and oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B. and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold, The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300° and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type, All samples were quenched from the annealing temperature in 10 per cent H2SO4 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.1 EFFECT OF SILVER Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By G. R. Frank, R. E. Willett, E. H. Hollingsworth

The most generally accepted equilibrium diagram for A1-Fe alloys has a eutectic system on the aluminum side with an essentially insoluble constituent of the formula, FeAl,, as the second phase. In 1938, Bradley and Taylor1 did report a phase change of FeAl,, but this change has never been confirmed. According to them, FeA1, is the stable phase only at higher temperatures; at lower temperatures, it is converted into Fe2Al7 and aluminum. It has now been found that there is, in fact, a phase change of the Al-Fe constituent on the aluminum side of the equilibrium diagram. This change, however, is not the one reported by Bradley and Taylor. The alloys used were cast by continuous processes and had these analyses: Fe - 1.98 to 2.02 pct, Cu-0.01 pct, Si - 0.01 pct, Mn - 0.01 pct, Mg - 0.00 pct, Zn - 0.00 to 0.01 pct, Cr - 0.00 pet, Ti - 0.00 to 0.04 pct. The constituent in these alloys was identified by X-ray analysis with a Guinier camera and by chemical and X-ray powder diffraction analyses. Two procedures were used to separate constituent for the last two analyses. In one procedure, it was separated by treating a sample with a solution of methanol saturated with iodine. And in the other procedure, it was separated by first applying, at 12 amp per sq ft in 15 pct sulfuric acid at 70°F, an oxide coating to a sample, and then dissolving this coating in a solution of 35 ml of 85 pct H3PO4 and 20 g of CrO3 per liter. Several observations directed attention to a phase change of the A1-Fe constituent. Differences that appeared too great to be accounted for by micro-structure alone were found in the voltages required to apply the same thickness of an oxide coating to products from rapidly and slowly chilled ingot. Even more striking was the difference in appearance of the coatings themselves. One applied to a product from a rapidly chilled ingot was dark gray in appearance, in fact, almost black, while one applied to a product from a slowly chilled ingot was essentially white. Also, even a short period of thermal treatment at an elevated temperature of products from rapidly chilled ingot led to the same anodizing behavior as that of products from slowly chilled in-

Jan 1, 1962

By E. P. Klier

The work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, I per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. Henever, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. Experimental Procedure The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, o.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to 5°C. at 540°C. (1004°F.) and above, and to 2°C. at 490°C. (914°f.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for nietallographic examination. Etch-ants used were Vilella's reagent (I gram picric acid, 10 ml. hydrochloric acid to make 100 ml. ethyl alcohol solution) and alkalinc sodium picratc (electrolytic). Vilella's reagent was effective in revealing all microconstitucnts, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used—the Debye-Scherrer method and a back-reflection method. 'The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

By C.R. Taylor, John Chipman

The study of chemical reactions of liquid steel and basic open-hearth slag involves a complex slag system of at least eight important components, and often a number of others. In initiating an experimental program on the equilibrium relationship of slag and metal, it became evident that but little progress could be expected in the interpretation of the complex slags until an understanding had been gained of the simpler liquid systems composed of a limited number of slag constituents. The simplest system that in any way resembles open-hearth slag must contain lime, silica and iron oxide. Attempts to produce in an induction furnace slags containing only these constituents have met with serious limitations because of the solubility of refractories in the slag. Thus in acid-lined furnaces the slag is always saturated with silica and consequently contains between 48 and 63 per cent of this component. In basic-lined furnaces an undesired additional component, magnesia, is introduced to the extent of some 3 to 15 per cent, depending upon the acidity, sometimes with disastrous results to the furnace. Thus in a magnesia-lined furnace, Fetters and Chipman1 found it impossible to prepare slags in which the ratio (CaO + MgO)/SiO2 was less than that corresponding to the metasilicate (approximately 0.8:I). Between this composition and that of the true acid slags lies a field of composition about which very little is known and which cannot be explored by any ordinary means. This circumstance, as well as the desire to study the more basic slags in the absence of magnesia, calls for the development of a method by which slags may be brought into equilibrium with molten metal without coming in contact with refractory. Such a technic has been provided by the rotating induction furnace developed by Barrett, Holbrook and Wood.2 Three modifications of the rotating furnace were described by these authors. The first was essentially a rotating refractory cylinder containing the magnesia crucible, which was itself heated by a graphite crucible. In the second, only the magnesia crucible rotated, the cylindrical graphite heater being stationary. In the third, the coil and crucible revolved, and the metal was heated directly by induction. Experimental Method Furnace The furnace used in this investigation differed from previous designs and may be Sci- a fourth modification of the original rotating furnace. Its essential fea tures are shown in Fig. I' The Outer case A is a fire-clay flue liner for control of the atmosphere. The top B and base 6 are alberene stone. The coil supports D are of ""Formica," a material formed from phe-

Jan 1, 1943

By C. R. Taylor, John Chipman

The study of chemical reactions of liquid steel and basic open-hearth slag involves a complex slag system of at least eight important components, and often a number of others. In initiating an experimental program on the equilibrium relationship of slag and metal, it became evident that but little progress could be expected in the interpretation of the complex slags until an understanding had been gained of the simpler liquid systems composed of a limited number of slag constituents. The simplest system that in any way resembles open-hearth slag must contain lime, silica and iron oxide. Attempts to produce in an induction furnace slags containing only these constituents have met with serious limitations because of the solubility of refractories in the slag. Thus in acid-lined furnaces the slag is always saturated with silica and consequently contains between 48 and 63 per cent of this component. In basic-lined furnaces an undesired additional component, magnesia, is introduced to the extent of some 3 to 15 per cent, depending upon the acidity, sometimes with disastrous results to the furnace. Thus in a magnesia-lined furnace, Fetters and Chipman1 found it impossible to prepare slags in which the ratio (CaO + MgO)/SiO2 was less than that corresponding to the metasilicate (approximately 0.8:I). Between this composition and that of the true acid slags lies a field of composition about which very little is known and which cannot be explored by any ordinary means. This circumstance, as well as the desire to study the more basic slags in the absence of magnesia, calls for the development of a method by which slags may be brought into equilibrium with molten metal without coming in contact with refractory. Such a technic has been provided by the rotating induction furnace developed by Barrett, Holbrook and Wood.2 Three modifications of the rotating furnace were described by these authors. The first was essentially a rotating refractory cylinder containing the magnesia crucible, which was itself heated by a graphite crucible. In the second, only the magnesia crucible rotated, the cylindrical graphite heater being stationary. In the third, the coil and crucible revolved, and the metal was heated directly by induction. Experimental Method Furnace The furnace used in this investigation differed from previous designs and may be Sci- a fourth modification of the original rotating furnace. Its essential fea tures are shown in Fig. I' The Outer case A is a fire-clay flue liner for control of the atmosphere. The top B and base 6 are alberene stone. The coil supports D are of ""Formica," a material formed from phe-

Jan 1, 1943

By John Wulff, Richard P. Seelig

THE importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by sub- sequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be con- trolled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper. In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshin1 on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin1 and Rakovski.2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,1 based on a hydro- dynamic analogy, however, leads to but another way of plotting density and pres- sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. DENSITY GRADIENTS IN COMPACTS The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By S. W. Parr

FRom a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows: Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric acid— 1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60" C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present. Sulfur in the form of iron pyrites, or marcasite, may be quantitatively removed without oxidation of the organic sulfur as follows: A dilute solution of nitric: acid is prepared having 1 part of concentrated HNO3 to 3 parts of water or with an approximate specific gravity of 1.12. The coal sample, ground to 100 mesh, is digested with this solution at room temperature for 3 or 4 days, filtered and evaporated to dryness, taken up with water, and acidified with hydrochloric acid. It is now ready for precipitation with barium chloride in the usual manner. If sulfate is present in the original sample to an appreciable amount, it should be removed by the procedure outlined above. It is not necessary here to give the methods for determining the two

Jan 1, 1920

By J. M. Hodge, H. M. Reichhold, R. D. Manning

The work reported in this paper represents the first of a series of investigations of the factors governing notch toughness in ferritic materials. This paper is concerned with two of these factors, namely, the effect of ferrite grain size, and the effect of an alloy content of 3.64 pct nickel. Every effort has been made to hold other variables constant in order to isolate the effects of these two. The compositions chosen for study were 0.02 pct carbon in order to eliminate the variable of carbide distribution, one steel being a plain carbon steel and the other alloyed with 3.64 pct nickel. Both steels were fully killed with silicon, without an aluminum addition, so that the variable of deoxidation practice was held constant. Finally, all samples were water quenched from 1200°F and tempered 24 hr at 300°F in order to hold the quench aging variable constant and to decrease the tendency for grain boundary carbide precipitation. The ferrite grain size was varied by heat treatment over the range of A.S.T.M. grain size numbers of about 2 to 6 in each steel so that the effect could be evaluated individually and the notch toughness of each steel could be compared at comparable ferrite grain sizes. Materials and Experimental Procedure MATERIALS The materials for this investigation were obtained from Battelle Memorial Institute as 250 Ib induction melts which were forged into 134 in. square bars and then rolled into 0.6 in. square bars. Both steels were deoxidized with silicon, the aluminum content being held to a minimum. Check analyses of these materials are shown in Table 1. HEAT TREATMENT FOR GRAIN SIZE The grain size was varied by varying both the cooling rate and the austeni- tizing temperatures. The heat treatments used and the corresponding grain size values are tabulated in Table 2. A semicontinuous network of grain boundary carbide was observed in the microstructure of both the plain carbon and nickel steels in the as rolled condition and an additional heat treatment was necessary to eliminate this variable. Therefore, all samples were water quenched from 1200°F and tempered 24 hr at 300°F as a final treatment before testing. This heat treatment served to eliminate to a great extent the grain boundary carbide network and to hold the quench aging effect constant. IMPACT TESTING Standard keyhole Charpy impact tests were machmed after heat treatment. A bath of acetone and dry ice was used for refrigeration of the samples down to temperatures of —94°F (—70°C) and a bath of either methyl-cyclohexane or isopentane, cooled by

Jan 1, 1950

By J. B. Warriner

S. A. TAYLOR, Pittsburgh, Pa.-What was the distance of haul? J. B. WARRINER.-There is practically no limit to the haul. The length is determined entirely by the feasible location for a dump. -I have known of hauls up to 2 miles in length. R. V. NORRIS, Wilkes-Barre, Pa.-This paper was originally presented to the Anthracite Section as the result of the appointment of Mr. Warriner as the Chairman of the committee to study this matter and present this paper. As he has stated, he obtained data very freely from all the stripping operations in the region, and it is a type of paper of which we should have more in the Transactions. Two or three things in it strike me as particularly valuable. The two tables, 1 and 2, showing the coal remaining, have been the result of a great amount of study, as it is not an easy matter to obtain data as to the amount of coal left in mining. As an example, one of the, anthracite mines was mined and robbed out in 1850, so the maps show. That mine is today producing 250,000 tons of coal, over 50 per cent. from the bed which on the maps is marked as exhausted. What actually happened is that the seam was on a light pitch inconvenient to mine. There was ample thickness of coal and the chambers were driven at a convenient pitch through this 30,-ft. bed, leaving top and bottom, taking out about 10 ft. The pillars were removed and the working caved and marked as gone. That is the type of area that is now being stripped, which explains the reason for the enormous amount of coal left in, and the fact that Mr. Warriner has worked out the actual results from a large number of strippings is of great interest to the operators in any region handling thick coal which has been mined over in the past, generation. The modern mining, of course, is different. We do not have all the coal we want in big veins, and we do not mine it that way. Another interesting feature of the paper to me was the study of losses. It is not uncommon to assume that after you have stripped off the overburden all the coal goes to market. Mr. Warriner has shown that there is a loss ranging up to 10 or 15 per cent. that does not go, so 'that estimates made on stripping, figuring on all the coal, are subject to this very material correction.

Jan 4, 1917

By Eleanor Haslem, Carl A. Zapffe

THE present investigation has three principal purposes: I. To develop a method for measuring hydrogen embrittlement that avoids certain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. SELECTING A TEST METHOD Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. DEVELOPING A MACHINE FOR MEASURING HYDROGEN EMBRITTLEMENT As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1946

By James Norman, O. C. Ralston, John Dasher

MOST mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chromite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficiation, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put in the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separation, at a density of 4,0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabromethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in, size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. EARLIER WORK It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the

Jan 1, 1942

By W. M. Rust, W. D, D. W. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so uni- versally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretations of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in, in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resistance. The recorder can be a vacuum-tube 1 References are at the end of the paper.

Jan 1, 1944

By B. M. Larsen, T. E. Brower

THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slag-metal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the con- tinual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process. In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium. On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. Probable Chemistry of Desulphurization Since there is little evidence that sulphur atoms in the iron solution are aasociated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* (FeS) ? [FeS], [I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) ? (CaS) + (FeO), [2] and, (FeS) + (MnO) ? (MnS) + (FeO). 131

Jan 1, 1949

By A. A. Collins

OF widespread interest to all lead metallurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process. † Older Methods Three older methods, i.e., 1. Dross plus siliceous ore and limestone. 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and anti- mony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from I to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about impossible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it was decided to experiment with the soda process. The Soda Process After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other sugge~ted the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1949

Book Review Mexico, TODAY AND Tomorrow. By E. D. Trowbridge, Detroit. The McMillan Co., New York, 1919, 353 pp., 7;2 X 5 in. $2.00. The first eight chapters are devoted to an historical narrative of the Mexican peoples from the earliest times to the close of the war with the United States in 1345. "In dealing with events antedating what may be termed modern Mexico" the author has "made no attempt at original research, and so far as concerns anything prior to 1900, the work here presented is a repetition, a reflection, of the findings of opinions of Fiske, Prescott, Bancroft, Luis Perez Verdia and other authorities." The remainder of the hook deals with Mexico during and since the Diaz regime. It is interesting throughout but is not always convincing or consistent. Social conditions are described in a way illuminating and possible only to one who is familiar with the peon and his hitherto seemingly hopeless position in reference to the wage system and church oppression. In fact, the author makes the hold accusation that the "primitive rather than immoral" condition of the peons in the matter of their marital relations is due to the disregard of the church for their welfare and capabilities. The true accounts of the Madero revolution and the Huerta regime read like fascinating medieval fiction. The reason given for men remaining in the Madero army is still the controlling one regarding any of the armies there. "They had horses, arms, all the food they wanted, money to spend and no work." The discussion of Mexican financial schemes is wholly from the Carranza viewpoint. To meet a monthly deficit of ten million pesos the author says "the government forced loans from the National Bank, and Bank of London and Mexico, and repeated the operation several times, finally practically exhausting their bullion and cash reserves. Hostile foreigners refer to this operation as the looting of the hanks! Drastic as this action was, there was good ground on which to justify it." However, that necessity knows no law is never an acceptable tenet except to him who applies the screws. The discussion of the economic problems and their solution is rather chimerical and presupposes a civil and national virtue in the present government not discernible except to one ultra friendly. The book is an interesting exposition of the very much involved situation from the viewpoint of approval of both the Carranza government and the attitude of the United States in its dealings with him. The editing of the book leaves something to he desired. P. E. B.

Jan 9, 1919

By Franz R. Dykstra

DEFINITIONS The ores of iron are classified in three general categories: direct shipping, concentrates, and agglomerated-i.e., pelletized or sintered. Direct Shipping As the name implies, direct-shipping ores are shipped as mined or, perhaps, after screening. Generally, direct-shipping ores are hematitic (R203), magnetitic (R304), or limonitic (2Fe2O3.3H20) in nature. Grades of direct-shipping ores vary widely. Prices are frequently related to the historical Mesabi standard of 51.5% iron, although certain premium lump ores may contain up to 68% iron. The use of direct-shipping ores is diminishing as the advantages of beneficiated ores become evident and reserves are depleted. Concentrates Where the nature of the deposit and economics allows, certain ores are upgraded. This may include no more than washing and screening, or may be as elaborate as fine grinding followed by magnetic, gravity, or even flotation procedures for separation. Coarser concentrates may be smelted "as is.'; Fine concentrates usually are sold as sinter feed. (Sinter, as used here and in the following, refers to a process by which a fine ore-carbon mixture is agglomerated at elevated temperatures on a direct-fired moving grate to eliminate fines and improve chemical and physical homogeneity.) Agglomerates-Pellets or Sinter The development of economic techniques of mining and concentrating taconite (fine-grained, ferruginous jasperoids) led to the introduction of the iron-ore pellet, which is now becoming the major form in which iron is introduced into the furnace. The tremendous reserves of magnetic taconites of the northern United States and Canadian Precambrian shield had been recognized for many years. A century of mining has seen the reserves of the direct-shipping or "red ores" of the Minnesota, Michigan, and Wisconsin ranges approach depletion. Research started in the 1930s has seen the evolution of motives and techniques to concentrate these stubborn refractory ores. The efficacy of concentrate pellets in iron-making has been such as to induce mines throughout the world to grind, concentrate, and pelletize otherwise shipping-grade ores. Table 14.1A.1 shows typical analyses of iron ore. Marketing-Prices of iron may be quoted on a value per long-ton (2240 lbs) or metric-ton (1000 kg or 2204 lb) basis, or on a value per long-ton-unit or metric-ton-unit basis. One iron unit represents 1 % of contained iron per ton. (Thus, a price of $0.45 per iron unit for ore containing

Jan 1, 1976

By B. M. Larsen, T. E. Brower

THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slag-metal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the con- tinual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process. In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium. On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. Probable Chemistry of Desulphurization Since there is little evidence that sulphur atoms in the iron solution are aasociated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* (FeS) ? [FeS], [I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) ? (CaS) + (FeO), [2] and, (FeS) + (MnO) ? (MnS) + (FeO). 131

Jan 1, 1949

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By W. D, D. W. Mounce, W. M. Rust

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so uni- versally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretations of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in, in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resistance. The recorder can be a vacuum-tube 1 References are at the end of the paper.

Jan 1, 1944