Search Documents

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Peter Deming

"PART 2 OF 2 (CONTINUED FROM SUMMER 2006 EDITION) CONSTRUCTION ISSUES (cont’d) The Influence of Ground Conditions on Collapse Sand and gravel strata provide frictional resistance to support active earth pressure. The angle of internal friction has only slight influence on computed stability. Sand and gravel material design parameters can be defined with SPT N-values. Silt strata should be analyzed using internal friction. Definition of soil parameters should be performed by laboratory testing. Cohesive materials, especially soft clay and peat, require careful definition for design. Shear strength should be determined by laboratory testing. Work platforms constructed over granular strata improve the ground resistance by increasing confining pressure. However, temporarily increasing overburden stress on cohesive ground reduces trench stability. If the ground contains soft cohesive deposits which are not normally consolidated to the construction overburden, these must be stabilized before attempting trench construction. Use of wick drains and surcharge fill to improve the ground is recommended. Ground stabilization work requires time, and should be performed by the Owner prior to trench excavation. The addition of cement, stone columns, or other measures to support trench excavation equipment is typically determined to be more expensive and less dependable than ground improvement. Excavation through peat can be especially problematic. Peat materials rapidly compress when earth pressures exceed preconsolidation stresses. Backfill materials provide a horizontal stress on the trench wall which can exceed the bearing capacity of peat. As the peat compresses, the trench becomes wider, and slurry levels drop and trench stability can rapidly deteriorate. If the peat is the closure layer, a shallow key is recommended. If peat is present on the trench wall, preconsolidation with surcharge is recommended. Bottom preparation and Backfill Placement Trench wall stability is a temporary condition which must be controlled by proper design and construction of work platforms and slurry features which influence ground support. Backfill materials and intimate contact of the backfill with the closure layer are permanent conditions which are the end goal of the work. The most common reason slurry trenches fail to provide working barriers is improper bottom closure. Either the closure layer is not engaged, or the backfill is not in intimate contact with the closure layer. This can result from construction problems associated with sidewall collapse described above, slurry performance and/or degradation, backfill placement methods, and failure to maintain the trench bottom clear of sediment prior to placing backfill."

Jan 1, 2006

By Stephan A. Jefferis

I presume that the questioner is not asking about the reduction of sulfate in groundwater to hydrogen sulfide as a result of biological activity promoted by organics in the grout hardener and that the question relates to sulfate attack on cementitious grout systems. For the project in Spain presented in my paper, we used a very high pulverized fuel ash (PFA) content in the cementitious material. This gives good sulfate resistance and indeed the chemical interaction will actually cause the permeability to drop for about 50 years without any question of sulfate attack and damage to the whole thickness of the grout - of course there will be attack at the exposed face of the grout where it is in contact with the contaminated groundwater. The mix had over 75% PFA, and also a very high overall cementitious content. The mix was the contractor's design and showed excellent behavior in laboratory proving trials. In grouts as distinct from concrete, PFA gives significantly better sulfate resistance than ground granulated blast furnace slag which is often used in Europe as a component of bentonite-cement mixes for slurry trench cut-off walls.

Feb 10, 2003

By William Gleason

"The times they are a changing, and, for the mining industry, the optimism is high. On Nov. 8, Donald Trump was elected as the 45th president of the United States, and the Republican Party won a majority of seats in the U.S. Senate and the House of Representatives, ushering in what many hope will be a positive change for the mining and extractive minerals industries.Trump has stated that one of his top priorities as president will be to increase spending on the nation’s infrastructure, which could help spark a boom for mining. He has also pledged to bring back coal jobs and reverse many of the environmental regulations that were put in place by the Obama administration. However, before the mining industry gets too far ahead of itself and plans for another Super Cycle, there are stark reminders that any work in the natural resources sector is complicated and challenging. On Dec. 4, the U.S. Army Corps of Engineers announced that it would not grant an easement that would allow the Dakota Access Pipeline to pass under a portion of the Missouri River in North Dakota. The proposed crossing of the oil pipeline is approximately a half a mile upstream from the Standing Rock Sioux’s Reservation, and for months, hundreds of protestors camped out at the site in an effort to halt the project, saying they feared how it would impact water supplies and sacred lands.Energy Transfer Partners, the company building the pipeline, said the pipeline is a $3.78-billion investment that will connect the Bakken and Three Forks production areas to major refining markets. The company signed voluntary easement agreements with landowners representing more than 85 percent of the properties along the four-state route but faced an organized protest from the Sioux Nation at Standing Rock. The protest gathered momentum and support through social and traditional media and became the focal point of global environmental and indigenous activism. The protestors claimed victory, at least temporarily, when the Corps of Engineers said it would look for alternative routes for the project. It’s a decision that could lead to a lengthy environmental review and one that has the potential to block the construction of the pipeline for months or even years."

Jan 1, 2017

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997

By Abdullah Arik

Verification of computer generated reserve models is essential since the computer does not automatically check the validity of methods and assumptions selected by the user and their results. For the computer to do model verification would require an expert system which would perform tests on the model and determine if the model is valid. Since such an expert system is not available, it is up to users to verify the models they develop.

Jan 1, 1995

By Everett H. Dobbs

The Tripoli deposits in the southwest corner of Missouri In Newton County and the northeast corner of Oklahoma in Ottawa County, located in the vicinity of Seneca, Missouri, contains an unusual and peculiar form of silica which has not been found any other place in the world. Its outstanding characteristic is the physical structure of the individual particle, The particle structure of the Missouri-Oklahoma type Tripoli accounts for its market. It is a soft, friable, porous, double-refracting silica of the chalcedony variety, The particle is porous, has a fibrous structure, no sharp edges or comers, ad an average size of less than .01 millimeter, It varies from 90 to 98 per cent Si02 with less than 1 per cent free silica in the form of quartz, 24; has ignition loss of 1 per cent and fractional percentages of iron, alumina, lime, etc.

Jan 1, 1960

By Charles C. Mosher

An in-mine seismic technique for detecting faults has been tested in a Western U.S. coal mine. This technique has been used extensively in the U. K. to help guide longwall mining operations. Explosives detonated on the face of a seam generate sound waves which propagate into the seam. Reflections from faults are picked up by sensors on the same face. Computer processing is then used to determine the fault locations. A known fault was successfully located in this test. Modifications to the U. K. procedures were required for the relatively thicker roan and pillar mines common in the Western U. S.

Jan 1, 1983

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By Dan Martz, Stuart Lipofsky, Dean Workman

"The Indianapolis Deep Rock Tunnel Connector (DRTC)—first in a vast network of storm water storage tunnels below Indiana, USA—was a wildly successful endeavor. Crews for the Shea/Kiewit JV drove a 6.2 m Robbins Main Beam TBM to world record rates. The machine achieved 124.9 m/day, 515.1 m/week, and 1,754 m/month in limestone and dolomite rock. The advance rates can be attributed to many factors including ground conditions and knowledgeable crew, but continuous conveyors are also of key importance. The novel conveyor system, manufactured by The Robbins Company, enabled continuous tunneling in a difficult layout that included two 90-degree curves and two S-curves. Spanning 11,777 m in its longest iteration, the system included nine booster drives plus a main drive. A vertical belt moved muck up the 76 m deep shaft to a radial stacker for temporary storage. The system, one of the most complex in North America and the first to operate in 90-degree curves, made swift tunneling possible. This paper will examine the world-class tunneling done at the Indianapolis DRTC and the role of continuous conveyance in reaching high advance rates. The logistics of the system will also be examined as it could apply to future tunneling projects with similarly complex layouts. INTRODUCTION The Indianapolis Deep Rock Tunnel Connector (DRTC) is the first phase of a nearly 28-mile long network of deep rock tunnels being built 76 m beneath the City of Indianapolis, Indiana by Citizens Energy Group. The Deep Rock Tunnel Connector (DRTC) Project is a 12.2 km, 5.5 m diameter tunnel constructed by S-K JV, a joint venture between J.F. Shea Construction and Kiewit Infrastructure Co. The tunnel is a $179 million project and is the first segment and southernmost portion of a deep, large diameter conveyance and storage tunnel system to provide overflow relief during wet weather events. The project is estimated to be completed in 2017 and will initially deliver 204,000 cubic meters of the planned 1 million cubic meters of CSO storage for treatment, as well as provide future connections to other tunnels in the overall system (see Figure 1)."

Jan 1, 2016

By Peter V. Barr

Despite the advent of modem firing control systems reheating furnace operations frequently allow significant thermal excursions in the discharged slabs or billets after furnace delays. Although HSM furnaces are not immune to this and other related problems, mini-mill operations are most vulnerable due to their more frequent delays and (often) less sophisticated control systems. In order to reduce these problems control systems will commonly include a thermal model, operating either on-line (interacting directly with the controller logic) or in an advisory, off-line mode. Using a new 'fast' thermal model, the paper examines the thermal response of a typical mini-mill furnace during both delays and the subsequent recovery period. A variety of firing strategies are explored and compared on the basis of maintaining thermal excursions within allowable limits for rolling. Other factors, such as the potential for overheating of billets within the furnace during delays and the overall thermal state of the furnace, are also considered in some detail. Although common practice, the use of conventional thermocouple zone temperatures for furnace control during and after delays is shown to be a dubious proposition. Keywords: Reheat Furnace, Modeling, Process Control

Jan 1, 2003

By J. Diaz

"Antioquia region, in Colombia, is considered one of the areas with the highest mercury contamination in the world due to its use in gold recovery through artisanal mining, emissions to the environment between 100 and 150 tonnes of mercury are estimated by year. Therefore it became necessary to develop a project in which it was proposed aim to empower traditional artisanal mining community, or in different areas, such as gold mining in the region of Antioquia, in the implementation of safe mining practices and environmentally sustainable, from the introduction of clean technologies, in order to prevent or mitigate the impacts generated by traditional mining on the environment and the communities involved. In order to achieve this training to traditional mining community developed and technical visits to artisanal mining were performed in order to optimize operating processes and promote safe mining practices. In the project more than 1400 artisanal miners were trained.INTRODUCTION In the developing world, a combined 30 million individuals extract more than 30 different minerals using rudimentary techniques. Gold is the preferred mineral extracted by artisanal operators due to its high unit value and its market price, which has increased almost sevenfold over the last decade (Veiga et al, 2014). The artisanal gold mining sector in Colombia has 200,000 miners officially producing 30 tonnes Au/a. In the Northeast of the Department of Antioquia, there are 17 mining towns and between 15,000 and 30,000 artisanal gold miners (M. Veiga, 2010) (Upme, 2014). This production, however, has caused environmental problems, including high levels of river siltation and mercury pollution (Veiga et al, 2014) (UPME, 2007) (Cordy et al., 2013). The mercury contamination in Colombia by artisanal gold mining has been recognized by a number of researchers and local authorities for over a decade estimated that the annual mercury emissions from artisanal gold miners in Colombia in 2007 were between 50 and 100 tonnes, however given recent gold value increases and gold rush activity, current mercury emissions are likely much higher. Colombia is likely the world's 3rd largest source of mercury emissions from AGM after China (240 to 650 tonnes of Hg/a) and Indonesia (130 to 160 tonnes of Hg/a) (Telmer and Veiga, 2008) and is the world's highest per capita mercury polluter (M. Veiga, 2010)."

Jan 1, 2016

By K. S. Olson

My reaction when first asked to present this paper was; "What could I possibly say that would hold the audience?s attention for 15 minutes? What could I offer that anyone familiar with the Nevada Barite Industry wouldn't already know?" Well, quite frankly I can't. The industry has certainly been anything but exciting for the past 10 years and, in fact, quite depressing. The challenge, for those few of us left in it, has been to keep it alive. At times it has felt like a doctor must feel with a terminally ill patient. All I can do is recap the past ten years, review the present state of the industry, and offer a few personal opinions and observations as to where I think we are headed.

Jan 1, 1993

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By Mei Song, Qingyu Deng, Xuewei Lv, Lu Liu, Chenguang Bai, Meilong Hu

"The carbochlorination of several silica materials was carried out in the temperature range from 900 °C to 1200 °C. In this study, silica oxides and gaseous chlorine with carbon as reductant were used. The optimal carbon silica mole ratio in different temperature was calculated by Factsage software and the results showed that the optimal values are 1.2, 1.4, 1.6, 1.8 at 900 °C, 1000 °C, 1100 °C, 1200 °C, respectively. According to the experiments, the chlorination ratios of several silica materials were increased with temperature increasing. In the same temperature, the chlorination ratio of diatomite is the maximum and the chlorination ratio reaches 79%% when C/SiO2 reaches 3 at 1100 °C.1, IntroductionPolycrystalline silicon is the main material to manufacture the silicon polished section, solar battery[1] and high purity silicon wafers[2], also which is the most basic function material of semi-conductor industry, electronic information industry and solar photovoltaic battery industry[3]. The conventional manufacturing process of polycrystalline silicon would be divided into three parts: the improved Siemens method, which was introduced and became the main process to produce the polysilicon products in China. Silane method and fluidized bed method. Silicon tetrachloride and chlorosilans have been employed as by-products in several fields like electronic, telecounications and metallurgy[4-6]• At present, the main applications of silicon tetrachloride include production of trichlorosilane by catalytic hydrogenation, synthesis of fumed silica and ethyl orthosilicate, production of optical fiber grade silicon tetrachloride.The conventional routes for the silicon tetrachloride production have been reported, including the direct chlorination and the chlorination process of ferrosilicon, abandon catalyst and silica[7]."

Jan 1, 2013

By J. L. Thompson

The combustion of pulverized coal is a century-old practice. Many people have investigated coal dust and the residual fly ash particles that re-main after combustion. But the combustion process and fly ash formation mechanism are not under-stood. Working at our Maysville, Kentucky lime plant, the Dravo Lime Company Research team has collected samples of partially burned coal dust from the flame of a pulverized coal burner. Specimens were placed in a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). Microscopic examination of the particles, together with a large collection of micrographs of lime dust fused to fly ash particles, now make it possible to theorize as to how combustion advances through a piece of coal dust. Coal is a physical mixture of carbon-based compounds interspersed with bits of ash-forming materials, primarily alumina-silicate compounds. The alumina-silicate materials are commonly in angular nodules measuring 100 A to 700 A across their major dimension. It would appear that if the coal particle is in a well mixed gas stream, combustion starts at the surface and advances radially toward the particle center. With poor gas mixing, it is common that combustion moves from one end of a particle and advances on a broad front almost normal to some axis. In either case the combustion process and ash-forming mechanism are the same. As combustion occurs the carbon-based compounds oxidize in a highly exothermic reaction. Heat from the re-action melts the alumina-silicate nodules causing them to flow together and coalesce into an open sponge-like structure. As melting continues surface tension of the liquid and free surface energy causes the sponge-like structure to simplify into fewer, larger pores. Most likely the lighter molecular weight hydro-carbons burn before the heavier species. This means that as the melting ash structure is metamorphosing to a single large pore, there continues to be out-gasing throughout the structure due to combustion. Surface tension will form a spherical piece of fly ash if the ash material is liquid for a sufficient period of time. Out-gasing from combustion of the heavier hydro-carbons will provide internal gas pressure to keep the particle spherical until it freezes.

Jan 1, 1978

By K. C. Shaver

The Sloan Ranch kimberlite complex is located approximately 130 km north-northwest of Denver in the Precambrian core of the northern Colorado Front Range (Figure 1). A Devonian age for the complex is suggested by the fossil assemblages in limestone xenoliths (Chronic and others, 1969), and by paleomagnetism of the kimberlite (E. E. Larson, personal communication, 1986). The presence of diamond was first reported in rocks from the Sloan diatreme by McCallum and Mabarak (1976). Prior to this time, the distinctive- appearing host rock of the Sloan diamonds had been quarried for use as terrazzo stone; examples may be seen in the floors of the airports in Cheyenne and Laramie, Wyoming. The Minerals Division of The Superior Oil Company obtained a lease on the Sloan property in 1980. During the next four years Superior built and fine-tuned a highly efficient diamond recovery facility, explored and tested the Sloan deposit, and used Sloan as a site for testing numerous exploration techniques for future use in a continuing exploration program in the Colorado-Wyoming kimberlite province. The Sloan property was ultimately determined to be sub- economic, but the lessons learned there have been very helpful in subsequent exploration efforts.

Jan 1, 1987

By David J. Krichten

A method of retrofitting air-fuel burners with oxy-fuel capability overcomes the potential problems associated with oxygen combustion in aluminum melting furnaces. The retrofit burner uses the existing combustion air connection, burner housing, and burner tile and replaces the gas tube with an oxy-gas burner. Maintaining a portion of the air flow to the burner reduces the potential for localized overheating. Proper design of the burner reduces NOx emissions by moderating the flame temperature with furnace gas recirculation. Economic analysis of using oxygen shows the benefits are increased productivity and reduced overall unit cost of melting. In practice, the melt rate in rotary furnaces increases by up to 50% and by up to 35% in reverberatory furnaces. Oxygen utilization reduces total melting cost by 112-314 cents per pound of aluminum melted.

Jan 1, 1997