Search Documents

By A. V. Tarasov

The lack of technology for processing of sub-grade ore concentrates and intermediate products for extraction of Zn, Pb, Cu and precious metals at the metallurgical stage was a constraint for an increase in the production of these metals. The technology developed in the Gintsvetmet Institute is based on an improved electrothermal smelting process for treating calcined charge, ensuring thereby a reduction in power requirement and improving the environmental performance of the process. Electric smelting of sub-grade polymetallic concentrates produces lead bullion, to which the bulk of gold and silver reports, as well as well segregated matte and slag concentrating the bulk of zinc. Lead bullion and matte are commercial-grade products; zinc is recovered from high-grade (15% Zn) slag by slag fuming process. Reduced loss of precious metals in slag ensured by the given technology is attributed to the fact that the slag contacts with matte with low contents of gold, silver and lead, rather than with lead bullion. Limited amounts of off-gas typical of electrothermal processes ensure cost-effective operation of dust recovery devices and a reduction in emissions of harmful pollutants into the ambient air.

Jan 1, 2002

By M. Schwartz

Mining in Argentina is diverse in terms of the number of minerals extracted from the country, but also in terms of the varied approaches and attitudes of mining investors and their trust in the country's individual provinces. Laws are discussed, investment attractiveness and taxation.

Jun 1, 2015

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

By J. A. Herrick

Jan 1, 1879

By Ed Sullivan

"Australia is one of the richest continents when it comes to mineral extraction, ranging from exotic projects like the Olympic Dam — a copper, silver and uranium mine believed to have the world’s largest uranium resource — to the extensive iron ore, nickel, coal and gemstone formations that provide many of the country’s most rewarding exports.Among the challenges to succeed in this industry is the ability to provide efficient “pitto- port” infrastructure performance, which essentially means ensuring that minerals move seamlessly from the point of extraction to the facilities that can then move them to international market destinations.To provide such efficiencies, avoid human error and facilitate automated mining functions, producers are increasingly turning to fiber optic cable suppliers for “end-to-end” communications and control solutions. Many such solutions include ruggedized cable and connectors that ensure the survival of fiber-based DCS/PLC automation/ control architectures for various types of mining operations, even in the harshest environments.Integrating the solutionAs industrial Ethernet and fiber optic cable emerges as the medium of choice in many industrial arenas, communication and control integration using the most appropriate products for a specific application is increasingly important.“This whole ‘pit-to-port’ performance concept is focused on control and process automation,” says Boyd McDonald, Founder and Managing Director at Datalek Systems & Electrical, Rockhampton Area, Australia. “It also means bringing reliability to networks and providing the needed bandwidth. An appropriate plug-and-play solution is also important because it takes human error out of the equation.”Datalek Systems & Electrical, is responsible for the design, installation and maintenance of numerous fiber optic communications systems including those that involve automation, security, access control an CCTV systems for open-pit and underground mining operations as well as LNG and coal seam gas facilities."

Jan 1, 2015

By Fred E. Gray

The mill of Bralorne Mines, Limited, is located on the government highway in the Bridge River mining district of British Columbia, approximately fifty miles northeast of Shalalth, the shipping point on the P.G.E. railway. Prior to 1931, the property now owned by Bralorne Mines, Limited, was operated by Lorne Gold Mines, Limited. During the early operation of the mine, the ore had been treated at various times in one of three small amalgamation mills on the property. With the succession to ownership by the Bralorne Mines, Limited, work was started on construction of a new mill of approximately 100 tons capacity per day. The new mill was put into operation in the month of February, 1932, and since that date has been in continuous operation, milling an average of slightly over 3,000 tons of ore a month. The ore treated in the Bralorne mill is a gold-bearing quartz containing a very small amount of silver. About 75 to 80 per cent of the gold is in the form of free gold, the principal remaining portion being intimately associated with pyrite and arsenopyrite. The gangue rock is quartz, together with varying but relatively small amounts of altered diorite or albitite. In some of the ore, usually the higher grade portions, there is also considerable talc, which forms much slime in grinding. The mill is situated near the portal of the main haulage tunnel and the ore is received directly from the mine ore-trains, which dump on to the grizzly over the coarse-ore bin of the crushing plant. Figure 1 shows the flow-sheet of the mill as it is now being operated. Various changes have been made in the flow-sheet and in the reagents since the commencement of operations, and doubtless minor changes will continue to be made in order to increase the efficiency of the mill. Among the more important changes were those from two-stage to single-stage grinding, and from amalgamation plates to blankets. The change in the crushing was made because too much crushing was done when both primary and secondary mills were employed.

Jan 1, 1933

By III Boxley

Most of us realize that our nation's roadways are under ever-increasing stresses, from higher traffic counts to increased tire pressures and their resulting loads. At a time when the interstate system as originally envisioned is completed, and the National Highway System is being drawn to replace it, it is appropriate that we examine design and construction methods for the next century. The stone industry shares a common desire to produce high quality, cost-effective roadways that perform over time. The superior sub-grade and road base structure provides for the superior roadway. Since I am neither an engineer nor a contractor, I will not attempt to suggest design or construction methods. What I can do is share my company's experience in supplying road base materials by using a historical perspective in Virginia and some trends in the market that we have observed. Road building and related non-building construction are still far and away our largest markets as an industry. If we can help to improve the end product of our biggest customers, we add value to our own product. Indeed, in a time of budget constraints and competing demands for government dollars, we must show value over the life of a pavement structure to ensure their long-term funding.

Jan 1, 1996

By Tom Setterfield

Monster Copper Resources ?Junior focused solely on IOCG deposits ?Founded by ex-WMC geoscientists ?Properties in Brazil, Wernecke Breccias (Yukon), Central Mineral Belt and Nova Scotia Nova Scotia ?JV with Wallbridge Mining Company ?Ongoing Story ?Presented as a case study in generation and implementation of IOCG exploration program

Apr 1, 2005

By S. Rajendran

The western continental margin comprises of the southwest coast (Cape Comorin-Mangalore), centralwest coast or Konkan coast (Mangalore-Bombay), northwest coast (Bombay-Gulf of Kutch) and the Laccadives area. Placer deposits of heavy minerals occur in discontinuous patches on the beaches along many parts of the west coast. The richest offshore placer deposits occur along the 25 km stretch of the southwest coast from Neendakara to Kayamkulam. The National Institute of Oceanography (NIO) surveys show that the sediments off the Konkan coast consist largely of silty sand, sandy silt and clay and the concentration of ilmenite is higher than the onshore. The heavy mineral concentration ranges up to 90% and has mainly ilmenite and magnetite with minor quantities of apatite, rutile, zircon, kyanite etc. The heavy mineral sands extend below the clays to water depth down to 20 m. The heavy minerals sands vary in thickness from 2-10 m. Offshore placers can be mined by using wire-line, bucket ladder and hydraulic dredges. Wire-line, bucket ladder and hydraulic dredges. Wire-line dredges may employ drag buckets or clamshell and hydraulic dredges suction or airlift principles. The dredges can be located on flat bottom or catamaran barges. Dredging of very near shore placers may be achieved by operating from land. The bucket ladder type of dredger has greater digging ability and hence can be deployed for mining placers which are partly consolidated or cemented or where the most valuable part of the deposit lies at the contact between the alluvium and the bedrock. This type operates very economically up to 45 m depth and needs minimum power requirement per unit dredged. Suction type hydraulic dredges can be operated very effectively up to 60 m water depths. This system is quite ideal for the inner shelf. The maximum practical economic working water depths for wire-line dredges are about 150 m. With the drag bucket modified into large net buckets, the method can be utilized to greater depths. They can be used in areas of high water currents and swells. The type of bucket can be changed readily with change in the nature of alluvium or substratum. The hydraulic suction dredge is the most suitable system for mining unconsolidated sediments. When the sediments are semi-unconsolidated, a cutter head can be mounted on the lower end of the suction pipe to agitate the seabed.

Jan 1, 1996

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By D. A. Smith

The successful integration of overburden casting techniques into the mine production cycle can be an extremely cost effective use of explosives. The entire mining cycle revolves around the cast blasting and to be successful requires a great deal of planning and cooperation. Several operations of Cyprus Coal Company in the Appalachian coal fields have successfully integrated blast casting into their mine plan. This paper will detail the parameters and necessary controls to integrate an overburden casting program into a surface coal operation.

Jan 1, 1993

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By Norman Schapiro

Future ore bodies will, most likely, be more costly to find, mine and process than those now in production because most of them will be of lower grade or found deeper. To evaluate an ore deposit for extraction of metal values it is important to select the optimum economic process from among the many available options. The physical and chemical behavior of the minerals present should govern the process selection. Process mineralogy which combines mineralogy and petrography with process development engineering generates the data on mineralogy, composition and texture of gangue and valuable minerals from which the optimum process steps can be selected in the commercial design of the ore processing plant. These insights also help in solving operating problems caused by changes in the ore body

Jan 1, 1981

By Orlando C. Rojas

The Potrerillos Smelter commissioned a new El Teniente converter in 1985. As a result of the use of this technology, the Peirce-Smith converters have been processing only high grade matte or white metal. These operational changes resulted in damages to the converter shells, excessive splashing and cold dope generation and very short refractory campaigns. The paper shows the modifications to the tuyere angle, mouth design changes and new techniques for mouth cleaning and gas handling. Operational results up to 1991 are also shown.

Jan 1, 1993

Miners really are an optimistic bunch. Even with the dark clouds hanging over the global industry, mining professionals still turn out in droves at industry conferences. In February, more than 7,200 professionals attended SME?s Annual Meeting in Denver, CO, a record. And the following week, more than 30,000 people converged on Toronto, ON, Canada for the Prospectors and Developers Association of Canada (PDAC) meeting. For many small and junior mining and exploration companies the PDAC conference is a place to find potential investors in their projects. The Investors Exchange attracts several hundred companies, each showing off their properties to the many money types who wander the hall during the four-day conference.

Jan 1, 2013

By Eric Lundgren

The mining paradigm is changing on the continent of Africa. Jessica Kogel?s closing statement from her September 2013 President?s Page (ME, September 2013, pp. 6) has never been more appropriate, ?Africa is shaping up to be the next mining powerhouse, and there is huge opportunity for local communities, national governments and private industry to work together to create a win-win situation for all.? Supporting this notion, attendance at numerous industry conferences around the world demonstrates the shift toward a more sustainable, more environmentally conscious extractive model. But questions remain: How effectively is the industry making this transition, and how willing are companies to learn from the experiences of others? The international development community, as we like to call ourselves, is going through a parallel shift. We are experiencing our own funding crisis; governments are not as flush with resources as they were pre-economic meltdown. But more importantly, after a half century of implementing development programs, we must admit that while some of our programs have been fantastically successful, too many still fail to achieve the goal of poverty alleviation for the world?s poorest. Moving forward, we are forced to recognize that achieving success in scale and sustainability is not always accomplished from our work alone. As the director of international programs for Africare, a nonprofit with more than 40 years of experience implementing community-based development programs in Africa, I can report that our organization is changing the way we think about successful development partnerships. Africare recognizes that for too long the mining sector and nonprofits have been at odds, choosing noncommunication as a ?solution? to the problem. Both sides now recognize that this standoff is outdated, and Africare, specifically, is ready to cross the proverbial line. We see the potential benefits of mining for local communities and, when done responsibly, the opportunity to properly manage Africa?s resource boom as a benefit to all. There are challenges in this conversation. Many mining professionals view nonprofits as whistle-blowers, ready in a pinch to speak to news sources and complain about poor operational standards. Those are advocacy organizations, and while their role is important, they are not the only nonprofits interested in mining operations in developing countries. Organizations like Africare, with decades of experience implementing poverty reduction programs, approach this differently. We know we can work with mining companies to promote economic opportunity in the communities where mining operations are occurring. We recognize that the conversation is difficult, and we are open to discussions about how we can bring our unique experience to bear on the problems faced by mining companies in carrying out their investment programs.

Jan 1, 2014

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By G L. Boyd

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal recovered by highwall mining methods.

Jan 1, 1998

By M. H. Haycock

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

"The mining industry suffers from a number of incorrect perceptions, one of which is that it is an outdated industry that has not changed for hundreds of years. But the truth of the matter is that mining is a vibrant, highly complex industry that not only employs highly skilled and educated professionals but is also often on the cutting edge of technology. It is an industry with projects that are ever-evolving and among the most challenging engineering feats in the world.Take for instance the U.S. 53 Highway Relocation project in Virginia, MN. While more of a civil engineering job than a traditional mining project, it is still a complex engineering challenge taking place in a mining environment that has called on the skills of eight state agencies, three federal agencies, a host of contractors and many consultants, including many from the local mining industry in the Iron Range of Minnesota.In 1960, the Minnesota Department of Transportation (MnDOT) constructed U.S, Highway 53 on a private easement owned by US Steel that cut across a massive taconite deposit. MnDOT constructed the highway with the agreement that if the highway needed to be moved to access the taconite deposit before 1987, US Steel would foot the bill. And if the move was required after 1987, the responsibility would fall to MnDOT. In 2010, MnDOT received the notice that the highway would have to move as property owner United Taconite planned to access the ore, setting in motion one of the greatest engineering challenges, and the highest risk project, in the history of the states’ transportation department.Pat Huston, U.S. Highway 53 Relocation project manager, opened the 90th SME Minnesota Section Conference in Duluth, MN on April 19 with a presentation about the project that includes 5 km (3.2 miles) of fourlane highway and a new 345-m (1,132-ft) bridge that will be the tallest in Minnesota when it is completed later this year.“This project was not business as usual,” Huston told the packed crowd. “Highway 53 connects Canada and the Iron Range to Duluth and Lake Superior. It is an important highway.”During his presentation he spoke about many topics that were familiar to the more than 1,100 mining professionals who attended the conference. In his keynote speech,"

Jan 6, 2017