Search Documents

By H. Conrad, V. V. Damiano, G. J. London

A method is described for producing single crystals of high-purity beryllium, Be-4.37pct Cu, and Be-5.24 pct Ni. These crystals were prepared for testing in compression parallel to the [0001] by orienting and lapping to within ±3' of arc of the (0001). Microstrain testing apparatus is described along with c axis compression results for ingot purity beryllium, twelve-zone-pass material, and the above-mentioned alloys. Results show no measurable plasticity for the ingot purity material from -196" to 400°C, although some surface traces of (1122) slip was observed at 200°C and above. The twelve-zone-pass material shows substantial microstrain plasticity at 220°C with slip on (1122). Both alloys show significant plasticity at room temperature and above with slip also on (1122) planes. THE two slip systems which normally operate during the plastic deformation of beryllium in the vicinity of room temperature are:' basal slip (0001)(1120) and prism slip . Pyramidal slip with a vector inclined to the basal plane has been reported for elevated temperatures,'-a but occurs near room temperature only at very high stresses.~ A summary of the available data on the effect of temperature on the critical resolved shear stress for slip on these systems has been compiled by Conrad and Perlmutter.~ It has been postulated6'7 that one of the principal factors contributing to the brittleness of poly crystalline beryllium at temperatures below about 200°C is the difficulty of operating pyramidal slip with a vector inclined to the basal plane. Hence, detailed information on the operation of such a slip system is important to understanding the brittleness of beryllium. The operation of pyramidal slip with a vector inclined to the basal plane is best accomplished in beryllium by compressing single crystals in a direction parallel to the c axis. In such a test the resolved macroscopic shear strzss on the basal and prism planes is zero and (1012) twinning which is favored by tension along the c axis does not occur. Hence, in c axis compression of beryllium the normal deformation modes are inhibited and the operation of pyramidal slip with a vector inclined to the basal plane is favored. In the present investigation, c axis compression tests were performed on beryllium single crystal as a function of temperature (77" to 700°K), purity (commercial and twelve zone pass), and alloy content (4.37 wt pct Cu and 5.24 wt pct Ni). Presented here is a description of the test techniques employed and the gross mechanical behavior observed. A detailed analysis of the slip traces developed on the surfaces of the deformed specimens during these tests and the results of electron transmission studies of the deformed crystals are given in a separate paper.B PROCEDURE 1) Materials and Preparation. Single crystals about 1 in. diam were prepared of the following materials: commercial-purity beryllium, high-purity beryllium, and two beryllium alloys, one with 4.37 wt pct Cu and the other with 5.24 wt pct Ni. The commercial-purity single crystals were obtained by cutting specimens from large-grained ingot of Pechiney SR material, which is approximately 99.98 pct pure. The high-purity crystals were prepared by floating-zone refining (twelve passes) a rod (7 in. by 1 in, diam) of Pechiney SR grade cast and extruded beryllium. Although an absolute chemical analysis of the zone-refined material was not established, mass spectro-graphic analysis, emission spectrographic analysis, and y activation analysis indicated that it contained in atomic fractions about 5 to 10 ppm each of carbon and oxygen, 1 to 5 ppm each of nickel and iron, and about 1 to 2 ppm of copper, with the remaining residual impurities being less than 1 ppm. Further indication of the purity of this material is provided by the critical resolved shear stress for basal slip, which was approximately 300 psi. The starting material for the alloy single crystals was 1-in.-diam floating-zone-refined (six passes) rod of Pechiney SR grade beryllium. Two such rods were wrapped respectively with sufficient weight of wire of high-purity copper (99.999 pct) or nickel (99.999 pct) to yield a 5 wt pct alloy. A seventh floating-zone pass was then applied to each of the rods to accomplish the initial alloying and an eighth pass for homogenization. Analytical samples were taken from regions of the rod immediately adjacent to where the mechanical test specimens were cut; these indicated 4.37 wt pct Cu and 5.24 wt pct Ni. 2) Crystal Orientation. To avoid the occurrence of basal slip during c axis compression testing, it is necessary to load the crystals as nearly parallel to the c axis as possible. Preliminary c axis compression tests indicated that plastic flow and/or fracture occurred at stresses of the order of 300,000 psi; hence on the basis of a critical resolved shear stress for basal slip of 300 to 400 psi, the maximum crystal misorientation permitted is about 4 to 5' of arc. Since this accuracy cannot be obtained using the usual back-

Jan 1, 1969

By James K. Gluck, William E. Galloway, Gary E. Smith, John P. Morton, Christopher D. Henry

INTRODUCTION Surface mining and in situ leaching of uranium have the potential to alter ground-water quality around mines and leach sites. Of particular concern is the fate of uranium and its associated trace elements: molybdenum, arsenic, and selenium. We wish to under- stand the natural processes that control trace element concentrations in ground water and how these processes will influence dispersion of the elements from a mineralized zone, both naturally and during and after mining or restoration. For example, it is commonly recognized that the trace elements are soluble in oxidizing ground water but are insoluble, and can be precipitated, in reducing ground water. Thus oxidizing, metal-bearing water leaving a deposit could re- enter reduced ground, causing the water to be re- reduced and the trace elements to be, reprecipitated. In a sense, this is recreating the original mineralization process. To accomplish the above goals, we have (1) examined the theoretical controls of concentrations based on the available geochemical and thermodynamic data, (2) determined the major ion composition and oxidation-reduction status of Oakville waters because of the influence of these factors on trace element solubility, and (3) determined trace element concentrations and distribution in Oakville ground water. The last approach is used to evaluate how well actual behavior follows predicted behavior. This report focuses on two elements, uranium and molybdenum, because they exemplify the results obtained. The report also is restricted to a regional study of Oakville ground water. Results of more de- tailed study in and around major uranium districts in the Oakville and much of the raw data that support the conclusions in this report are presented in Galloway, Henry and Smith (1980). This report is part of that larger study, which concerned the depositional systems, hydrology, and geochemistry of the Oakville. The U.S. Environmental Protection Agency funded the study, under grant numbers R-805357-01 and R-805357-02. Theoretical controls were determined by reviewing the available literature on aqueous chemistry and behavior of uranium and molybdenum. To aid in under- standing water chemistry, Oakville water analyses were run through a modified version of the computer model WATEQF (Plumer, Jones, and Truesdell, 1976). WATEQF calculates speciation of dissolved ions and determines saturation with respect to a variety of minerals. In the discussion below, ion activity products (IAP) are compared with the equilibrium constant (KT) for various reactions and mineral products. Values of log IAP/KT near zero indicate that the water is in equilibrium with a mineral. Values less than -1 indicate considerable undersaturation and values greater than +1 indicate oversaturation. Galloway, Henry, and Smith (1980) give a more complete discussion of the application of this approach to Oakville water chemistry. Eh-pH diagrams have been constructed or adapted from the literature to predict what form -- dissolved ion or stable mineral species -- uranium and molybdenum assume under various conditions. Construction of the diagrams has followed procedures described by Garrels and Christ (1965). This approach is particularly appropriate because the solubility of the elements is Eh-dependent, and Eh varies greatly within the Oakville aquifer. A number of assumptions or approximations are inherent in the use of Eh-pH diagrams and chemical models such as WATEQF and in the interpretation of water chemistry in general. Both Eh-pH diagrams and chemical modeling rely entirely upon available thermo- dynamic data, including free energies of formation and dissociation constants for various reactions. These values are known to varying degrees of accuracy. Most major ions and minerals are relatively well control- led; however, data for trace metals are much poorer. Thermodynamic data are not available for some minerals, and for other minerals, two or more divergent values exist. By necessity, we have relied on the judgment of others to evaluate thermodynamic data. Calculations by WATEQF and constructions of Eh-pH diagrams are based on an assumption of equi1ibrium. Equilibrium may not be comnon in low-temperature aqueous environments; at best, ground-water composi tion may be in a state of dynamic equilibrium, continuously changing due to changes in environmental conditions. Eh-pH diagrams show what phases are stable at equilibrium under given conditions; they do not prove that the phases actually exist. Many minerals persist or form metastably under conditions outside their equilibrium stability field. The kinetics of reactions, which cannot be evaluated here, are important in determining what phases occur. Kinetics may be less of a problem for ground water that travels and evolves slowly through a semihomogeneous matrix than for many other natural systems. Eh-pH diagrams show equilibrium fields only of phases included. They do not indicate anything about stability relative to phases not included in the diagram. WATEQF, obviously, cannot calculate the degree of saturation of a mineral not included in the program or for which the appropriate ions were not analyzed. Thus, a mineral that was not considered may be the most stable phase under a given set of conditions and may control the solubility of a trace element. Also, this study is limited exclusively to in- organic compounds. Organic material is known to be an

Jan 1, 1980

By Henry H. Roos

NTRODUCTION In the mining industry, a "drill jumbo" is a drilling unit equipped with one or more rock drills and mounted on a mechanical conveyance. Jumbos range from single¬drill ring drills mounted on simple steel skids to sophisti¬cated multiple-drill units mounted on diesel engine powered carriers and equipped with automatic controls and sound-abatement cabs. Individual types of jumbos usually are designed for specific tasks such as fan drilling in sublevel caving operations. Some units, such as development jumbos, can be utilized for several functions in addition to their normal applications, e.g., for production drilling in room-and-pillar operations, stoping in cut-and-fill mining, etc. Mine operators can purchase individual components from manufacturers, assembling these components into a jumbo suitable for specific conditions. However, this requires that mine personnel have good engineering and mechanical abilities. Although manufacturers of jumbos maintain facilities for designing machines to meet con¬ditions created by new mining methods and unusual ap¬plications, the cost of the engineering and experimental work for new types of jumbos should be evaluated in terms of both costs and benefits; it may be advantageous to plan the mining operation so that existing and proven units can be utilized. GENERAL SELECTION CRITERIA Since the operating conditions vary in underground mines, the design of a jumbo must be selected to cope with the individual characteristics of the mine. The necessary considerations include access space into the working areas, grades expected to be encountered, radii of the curves, ambient temperatures, the characteristics of the rock, the acidity or alkalinity (pH rating) of the mine water, etc. Access to Mine Workings The mine workings must be accessible to the selected jumbo. Frequently, a jumbo must be disassembled at least partially to pass through the mine shafts. There¬fore, a bolted construction allowing disassembly into pieces of suitable size and weight is desirable in most applications. Type of Undercarriage Generally, a crawler-type undercarriage should not be used in trackless mines having acidic mine water. The acidic water causes an electrolytic action between the individual crawler parts and causes rapid corrosion and early failures. Propulsion A two-wheel drive on a pneumatic-tired jumbo is marginal for grades exceeding 12%. A four-wheel drive unit with good weight distribution is capable of operat¬ing on grades of up to 35%. At least 30% of the gross vehicle weight (GVW) should be carried on the steering axle; otherwise, the steering tires may not have sufficient traction on loose road surfaces and may "plow" instead of steer. To assure stable operation in mines with steep grades, the height of the center of gravity of the jumbo should be considered. It should not make the unit prone to rolling over on the steep grades that may be encoun¬tered. Turning Ability In confined working areas, a skid-steering or crawler unit has the best maneuverability. An articulated carrier is preferable when base-rotated parallel booms are being utilized. A rigid-frame jumbo with automotive steering is compact and economical, having lower maintenance requirements than the other two types. However, the turning radius of a rigid-frame unit is wider than either the skid-steering or articulated units, and this wider turning radius may be detrimental in mines with narrow drifts. JUMBO COMPONENTS Rail Undercarriages A mine with a rail-transportation system generally utilizes drill jumbos that are mounted on rail-type under¬carriages. With a light load and good weight distribu¬tion, this carrier may consist of a simple two-axle four-wheel platform onto which the boom-mounting brackets are attached. As the depth of the round and the penetration rates increase, the weight of the equip¬ment installed on the chassis also increases. The greatest problem with a heavy overhung load is balancing the carrier; a three-boom unit may require a substantial amount of counterweighting to maintain an acceptable 70% to 30% axle-load balance. Although lengthening the wheelbase helps balance the unit, a long wheelbase increases the turning radius, often creating problems on curves and sometimes requiring a swivel truck-type chassis. A good rule of thumb for a simple four-wheel undercarriage is to maintain a wheelbase length to track gage-width ratio that does not exceed 2.5 to 1.0. For a larger ratio, a swivel truck should be utilized. Swing-out outriggers or roof jacks help keep a jumbo in place during the drilling cycle. Usually, a rail-mounted jumbo is not self-propelled. Instead, it is maneuvered into place by a locomotive. Occasionally, several headings are being advanced in close proximity, and a self-propelled jumbo is con¬venient. In electrified mines, such a jumbo utilizes conventional battery-powered traction gear; in dieselized mines, hydrostatic drive components offer good flexi¬bility. The tractive power requirements of a typical rail jumbo may be calculated from the formula: HP = [(RR + GR) X Sl/[33,000 X Em X Eh]

Jan 1, 1982

By J. H. Polhems, R. B. Brackin, D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill. The Mascot ore is a lead-free, honey-colored sphalerite in dolomitic limestone, with lesser amounts of chert and some pyrite. A mineralogical analysis is given in Table I. After 10 years of successful operation with galena medium and treatment of nearly 10,000,000 tons of ore, a decision to convert to ferrosilicon was made early in 1948 because of the increasing price of galena and consequent high operating costs. The conversion was made on Nov. 6, 1948, and the results obtained since that time have shown remarkable improvement over those made with galena. The Table I. Mineralogical Analysis of Mill Feed, Pct Calcium carbonate 49.5 Magnesium carbonate 35.2 Iron oxide and aluminum oxide 1.5 Zinc sulphide 4.5 Insoluble 9.3 100.0 Table II. Comparative Data, Galena and Ferrosilicon Ferro- Diner-Gelenaa siliconb ence Operating costs per ton milled, ct. 21.21 9.12 12.09 Medium consumption per ton milled, lb 0.80c 0.15 0.65 Reagent consumption per ton milled, lb 0.45 0.02 0.43 Tailing assay, pct Zn 0.310 0.297 0.013 Concentrate. oct Zn 12.08 10.33 1.75 Heavy medla ieparatlon recovery. pct 89.38 90.22 0.84 Mill feed rate, tons per hr 153 166 13 Heavy mesa separation feed rate. tons per hr 100 10 0 Tons milled per heavy media separation man shift 350 620 270 Mill feed to coarse tailings, pct 51.0 56.7 5.7 Lost mill time, pct 5.6 5.0 0.6 Power consumption, kw-hr per ton 2.06 1.92 0.14 a 1947. " First 6 months of 1950. c Net consumption after deducting credit for reclaimed waste galena. Consumption of new galena was 1.320 lb per ton milled. For entire life of galena operation, a credit of 40 pct of the value of the new galena added was realized from the sale of waste galena. comparisons given in this report cover the first 6 months of 1950 as representing the ferrosilicon operation, and the year 1947 as representing the galena operation. This was the last full year in which galena was used exclusively and is representative of the best work done during the 10 years of operation with this medium. After only 2 years' operating experience, with ferrosilicon and treatment of 1,807,585 tons many advantages have been revealed and are summarized in Table 11. Development Prior to the introduction of the heavy media process, all the mill feed was crushed through 5/8 in. and treated by jigging. A finished tailing assaying 0.66 pct Zn was made on rougher bull jigs, and cleaner jig tailings were ground for treatment by flotation. The first test work on the sink-and-float method of mineral beneficiation was carried out at Mascot in 1935, using a 3-ft cone and galena medium for batch tests. The following year a 6-ft cone was installed for pilot-plant work. This unit became a part of the mill circuit on March 1, 1936, and handled a gradually increasing tonnage in the next 2 years as the process developed to the point where it could treat all the + 3/8-in. material in the mill feed. Coarse jigging was then discontinued on March 1, 1939, and all coarse tailings have been made by the heavy media separation plant since that time. Feed Preparation: The original feed preparation plant consisted of a drag washer followed by two 4x10-ft Allis-Chalmers washing screens. A surge bin and two additional 5x12-ft AC washing screens were added in 1943. Use of primary and secondary washing screens was found essential to provide the cleanest possible feed for the cone and thereby avoid excessive contamination of the galena medium. Improved washing was obtained by replacing the drag washer with a 7x20-ft Allis-Chalmers scrubber, shown in Fig. 2, which has been in service since May 1944. Throughout the life of the galena operation, delivery of extremely muddy ore to the mill overloaded the medium cleaning system, and it frequently was necessary to cut off the feed and clean the medium for several hours until its normal viscosity had been re-established. The cleaning circuit

Jan 1, 1952

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article' describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation. Some attempts were made in 1931 by the owners of the Hawkesworth patents to interest Ontario gold mine operators in the bit. These efforts were not successful, but they undoubtedly stimulated thinking which resulted in the invention and patenting of several well-known Canadian detachable bits, one of which is now a widely used throwaway bit. The success of the Butte installation also led to the development of the threaded type of bit connections by several well-known manufacturers, and in 1935 these bits were introduced to the mining industry on a national scale. The original Hawkesworth bit was not provided with a water hole but, depended upon water passing through the clearance opening between the tongue in the bit and the groove in the rod to flush cuttings from the drill hole, see Fig. 1. In December 1935 it was found that this method of introducing drilling water to the bit face resulted in high dust counts. To correct this a water hole was drilled on the central axis of the bit, passing through the tongue. Unfortunately, quenching water would rise through the small water hole, spot-hardening the tongue to cause breakage, never completely eliminated. In the fall of 1936 large-scale tests indicated that savings would be effected by use of a threaded type of bit, which was therefore adopted as standard for all Butte mines. This type of bit was used until 1947, when it was superseded by a one-use slip-on type. Since the first use of the Hawkesworth bit every detachable bit of importance has been investigated, and where advantages which might reduce costs or increase efficiency were indicated, substantial tests of the bit were carried on in the Butte mines. When tests demonstrated the advisability of changing from one kind of detachable bit to another the change was made at one level or in one area each day until the new rod and bit equipment was used throughout the mine. This involved a minimum of cost and disruption of drilling. Intelligent selection of a detachable bit to obtain optimum results requires careful consideration to achieve a balance between the three principal types of equipment used in the drilling process: 1—drill bits, 2—drill steel, and 3—drilling machines. Optimum results imply maximum output and minimum cost per unit of output. Since every rock type differs in drillability and it is generally impractical to provide equipment for more than one or two types of rock which may occur in one operation, selection of equipment must encompass average drilling conditions. However, on exceptional occasions several widely differing conditions may make it mandatory to provide equipment best suited to each condition. The choice of rock-drilling equipment is a most controversial subject and one that is further complicated by unreliable and frequently misleading performance claims. Small operators without the means for making accurate evaluations of equipment frequently suffer from these over-enthusiastic claims. It is apparent from experience in rock drilling throughout the world that rock drillability is not alike in any two places, and that selection of proper equipment can only be made after conducting thorough trials of various types of equipment. Some recent drilling tests in tactite and hornstone at the Darwin, California mine of the Anaconda Co. present some interesting clues on rock drillability. Microscopic examination of thin sections of these rocks reveals that mineral composition and rock texture are equally important in governing drillability. The Darwin hornstone is at times so abrasive that the carbide bit cutting edges become flattened to 3/32 in. in 2 to 4 ft of drilling, and some carbide bits were dulled to this point after 9 to 10 in. of drilling. This wear was determined to be the proper point for resharpening to eliminate carbide insert breakage or breakage of the steel rod when drilling with 1½ to 1?-in. bits, with a drifter of 2 3/4-in. diam and 90 to 100 psi air pressure, see Supplement A. Before considering the merits of various bit designs it may be well to review the mechanics of drilling rock with percussion drills. A sharp bit cuts by penetration and chipping. The amount of penetration governs the amount of chipping and depends upon the contact area of the cutting edge, the foot-

Jan 1, 1954

By AIME AIME

PROBABLY no man has been of greater service to the Institute and has kept more in the background than Henry Krumb. A Vice-President continuously) for the last eleven years, apparently neither his picture nor a biographical sketch ever have adorned these pages and were he forewarned in the present instance he would order us to "forget it." He is a Columbia School of Mines man, Class of '98. He worked underground at Rossland, B. C. for a time, then for a year and a half a. chief engineer of the famous Camp Bird at Ouray, Colo. For three wars he was examining engineer for the Guggenheims and since 1901 has been an independent consulting engineer with experience throughout the Americas.

Jan 1, 1939

By J. W. Smith

Our continuous search for underground productivity improvements has been brought about by the diminishing ore grades in existing underground mines. The need for more efficient mining methods is a result of the economic problems facing our industry today, and this has caused us to evaluate underground haulage methods which have traditionally been the "bottleneck" in the flow of material from the ore in the natural state to the surface processing facility of any underground mining operation. Small improvements in the face haulage systems have yielded much greater benefits as they relate to overall mine productivity so it's only natural that we are all concerned with the best method of moving ore from the face to the main line haulage. In a recent paper titled "Underground Haulage Trucks - Gaining Momentum Worldwide", Richard A. Thomas concludes that the use of trucks to haul ores in underground mines is on the increase spurred by the convergence of a number of technology advances and economic realities. Perhaps the most important stimulus for the growth of trackless haulage is the high degree of haulage flexibility in underground operations. On the economic side, the demand for higher productivity from underground mines has resulted in larger physical dimensions of haulage roads, that is, higher backs and wider drifts to provide more room for high capacity haulage units. In the process of determining the most effective type of equipment for haulage, the power source must be a major consideration. For the purpose of this paper, we will limit the comparison to rubber-tired trackless haulage vehicles and not try to make a comparison between rubber-tired haulage, continuous haulage systems and rail-mounted haulage. Cost is perhaps the only really measurable factor when making a comparison between electric and diesel haulage. You will find that some costs will be very well defined in absolute terms. In other areas of comparison, cost can be fairly well estimated, and yet in still others, the costs are totally arbitrary. Let's take a look at some of the cost considerations. (Figure 1) first of all, is the initial cost of the equipment. This capital cost quite often is a determining factor in the type of haulage vehicle to be selected, yet this initial cost is perhaps the most insignificant of all costs when evaluating an operation over the long term. Of much greater concern, is the cost of maintenance. This cost will often run three times the original capital investment during the life of a single piece of haulage equipment. This factor can include rebuild to extend the life of the original capital investment, but certainly includes the labor and materials necessary, plus the inventory to keep the equipment in good repair. Perhaps one cost which is now playing an even greater role in the rubber-tired haulage operation, is the cost of fuel. Conoco has recently come up with some rough estimates which indicate that diesel fuel will cost an average of three times the equivalent kilowatt output in direct electric power. Diesel fuel is almost twice the cost of stored electric power. (This of course relates to the efficiencies of charging and recovery of power from lead acid storage cells.) These particular figures of course will vary from one area to another but I think that there is enough significance here to certainly warrant the further study of fuel costs for each particular area or mine. Another cost is breakdown expense. This must be treated differently from maintenance costs because a potentially larger expense is involved, more than just parts and labor. Now we have to deal with the cost of lost production time, which can have a much greater overall effect. Mine plan economics are another cost consideration where we can't make a comparison without looking at specifics. Here you must look at the movement of power centers vs. the flexibility and freedom of movement of vehicles. The determination must be made as to what types of equipment will fit into any predetermined mine plan and if a change in the planned roadway dimensions for the mine plan itself would be more economical so that more efficient type of equipment could be utilized. Finally, two of the most important aspects to be considered with potential ramifications far beyond what we have mentioned previously, is the cost of health and safety, which is really the cost of meeting current and future government regulations, reasonable or otherwise. And of course, when making any consideration here it is impossible to come up with anything more than an educated guess on the cost of meeting the new regulations. Now let's take a look at some of the advantages of diesel vehicles as well as advantages offered by electric vehicles, both battery and cable powered versions (Figure 2). Much of the data used in this comparison is based on experience with three vehicles manufactured by Jeffrey Mining Machinery Division, Dresser Industries. Jeffrey manufactures all three types, each with approximately a 15-ton capacity, even though few of these Jeffrey vehicles are used in uranium mining operations. Much of our experience comes from the 4114 diesel powered RAMCAR which is a 4-wheel drive, articulated steering,vehicle powered by a Caterpillar 3306NA engine and using a powershift transmission. This will be compared with the performance of the Jeffrey 404H battery powered RAMCAR with articulated steering which utilizes a separate 35 HP DC drive motor on each of two wheels with solid-state speed controls, and the final comparison will be made on the Jeffrey 4015 cable-reel shuttle car which is powered by two 60 HP constant

Jan 1, 1982

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,' which had been used since the early 1930's by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell's plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell's practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By A. J. Mortlock

Cobalt and nickel have been diffused at tracer concentrations in gold at several temperatures in the range from approximately 700° to 950°C. The diffusion penetration profiles were determined by a serial sectioning technique in which the gold is first anodized and then the anodic layer is dissolved in acid. In this ulay sections as thin as 250A could be removed reproduci-bly. In all cases, the region close to the specimen surface was characterized by irregular behavior in the sense that the logarithm of concentration was not linear in the square of the penetration distance. In sotne cases, there zuas an indication of the operation of very slow dijfusion in this region, while in others the apparent diffusion coejj'icient was negative. Possible reasons for this anomalous behavior are briefly discussed. In recent years it has been found that the region close to the surface of a metal can sometimes exhibit anomalously slow diffusion characteristics relative to the interior of the metal. One of the best examples of this fact is the work of Styris and omizuka,' who showed that the apparent diffusion coefficient for zinc in the region withi: about 1 p of the free surface of copper was about ,,,, that at deeper penetrations. This result is particularly interesting, because it is free from the possibly complicating effects of low solubility of the diffusing tracer in the solvent metal. In the case of diffusion under conditions of low solubilitjr, interpretaticn of the results in terms of lattice diffusion is difficult because of the enhanced short-circuiting produced by segregation to dislocations.2'3 Measurements by Duhl et 1. suggest that cobalt diffusing in gold may also show a near-surface effect of this type. Once again the solubility is high, so that this result could be of great interest. However, the technique used for analyzing the diffusion penetration zones by Duhl, viz. the counting of residual gamma activity in the specimen following sectioning, appears to have indicated a near-surface effect in a parallel experiment on the self-diffusion of gold reported at the same time. The latter result is known to be spurious, since Kidson5 has demonstrated that self-diffusion in gold does not show this effect. Duhl et 01. also reported some measurements on the diffusion of nickel in gold, but failed to give any data for the near-surface region. As the solubility of nickel in gold is high, such data would also be of special interest. We, therefore, decided to conduct another set of experiments on the diffusion of nickel and cobalt in gold, using a sectioning technique that allows the individual sections to be assayed for solute content and thus gives direct determinations of penetration profiles. Also, by sectioning with an anodizing/stripping tech- nique, very thin layers can be removed and the region close to the surface studied in detail. MATERIALS The gold specimens were supplied as single crystal disks $ in. in diam by a in. high by Monocrystals Co. of Cleveland, Ohio. The gold itself was of spectro-scopic purity, i.e., better than 99.99 pct pure. METHOD Specimen Preparation. One flat end face of each gold crystal was spark planed with a Servomet spark erosion machine set for minimum spark energy. Following this treatment the crystals were preannealed for 2 to 4 days at temperatures of either 400" or 700°C. The three crystals preannealed at 700°C showed signs of recrystallization. The spark-planed end face of each crystal was then coated with the appropriate amount of 63i or 60 radioactive tracer. This deposit was laid down in a simple plating bath containing the as-supplied solution of the radioactive isotope as well as sufficient ammonium oxalate to saturate the solution. Some ammonium oxalate remained undissolved on the floor of the bath for this purpose. During plating further additions of ammonium oxalate were sometimes required to allow the plating to continue satisfactorily, perhaps due to passivation of the undissolved oxalate already present. The thickness of the deposited layer was determined by comparison of the apparent surface activity of the plated specimen with that of a similar specimen having a weighable deposit of the isotope on its end face. Correction for self-absorption of the radiation was made in this calculation. Annealing. The deposited crystals were annealed in a hydrogen atmosphere in sealed silica tubes. During this heat treatment they were supported, active face down, on optically flat silica plates. The temperature was measured with calibrated Pt vs Pt-10 pct Rh thermocouples, and the tabulated values can be taken to be correct to Z°C. All the crystals showed evidence of recrystallization following these heat treatments, suggesting that initially they may not have been good single crystals or had suffered strain during delivery. Concentration Profile Analysis. After annealing, the crystals were sectioned by the anodizing-stripping technique.6 The anodizing involved suspension of the specimen with its cylindrical axis horiz6ntal by a gold wire in a 200-ml beaker containing 1 M Hg304. A cathode in the form of a strip of gold sheet, 2 in. wide and positioned to be in contact with the curved side of the beaker, completely encircled the specimen. An anodizing current of 30 ma, corresponding to a current density of 5 ma per sq cm on the surface of the specimen, was passed for times ranging from 5 to 150 min depending on the thickness of gold to be removed; the solution was stirred continuously during this process. Following this treatment, the specimen

Jan 1, 1969

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

By M. S. Azun

M.S. Azun I have many objections to the content of the author&apos;s paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV&apos;s) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author&apos;s paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author&apos;s practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV&apos;s. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV&apos;s. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO&apos;s shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By D. Harker, M. J. Murphy

THE mechanism by which age-hardening takes place is still not completely understood. The principal theories range from the extreme of "precipitation-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. PREPARATION OF FORMVAR REPLICAS OF METALLIC SPECIMENS This section is concerned with the techniques that have proved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. It is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work-very fine polishing and etching with very dilute solutions-is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. PREPARATION OF METALLOGRAPHIC SPECIMENS The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch-to approximately the depth necessary for a micrograph at 1000 diameters-usually produces a sur-

Jan 1, 1945

J. E. Stead, Middlesborough, England (communication to the author): Prof. Howe&apos;s valuable paper on cast-iron brings forward most prominently the correct explanation of the part played by combined carbon in pearlite and cementite, in determining the strength and hardness of cast-iron. On a previous occasion I haveoshown that castings made by melting a white Cleveland iron and glazed iron, one containing 1.5 and the other from 4 to 5 per cent. of silicon, and each about 3 per cent. of carbon, were stronger than those made of ordinary foundry-iron; the difference in the final castings being a differ-

Jan 1, 1902

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.&apos;TheRittinger In its first form, as stated by P. R. Ritted.&apos;tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin&apos; as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory state of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which are useful for predicting machine performance and give, acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary in commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed&apos; in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted. In its first form, as stated by P. R. Rittinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include .the concept of surface energy; in this form it was precisely stated by A. M. Gaudin2 as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended. According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps, 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported&apos; that support the theory in its first form by indicating that the new surface produced in. different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work" done on. the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading since it does not follow the regular breakage pattern of most materials but is relatively harder to grind at the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory&apos; is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr/log 2.5 The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in. reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-1.5 If a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The&apos;evaluation in terms of kw-hr per net ton of 200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of -200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned, with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1952

By F. W. Schremp, V. L. Johnson

This paper discusses the results obtained from high temperature, high pressure filter loss studies in which field samples of clay-water, emulsion, and oil base fluids were used. High temperature, high pressure tests of some premium priced emrilsion and oil base drilling fluids show filter loss peculiarities that are not predicted by standard API tests. It is recommended that high temperature, high pressure filter loss tests be used to evaluate the performance of such fluids. Apparatus is described which proved to be satisfactory for evaluating filter loss behavior over a wide range of temperatures and pressures. INTRODUCTION The petroleum industry spends large sums of money each year on chemical treating agents for lowering filter loss and on premium-priced low filter loss drilling fluids. While it is an accepted fact that low filter loss is advantageous during drilling operations, it is questionable whether the present standard method of determining filter loss gives a reliable indication of the loss to he expected under bottom hole conditions. The purpose of this paper is to show that high temperature. high pressure filter loss tests Should be used to evaluate filter loss behavior of fluids for deep drilling. Concern over possible effects of filter loss on oil well drilling and well productivity dates back to the early 1920&apos;s. During the years 1922 to 1924, filtration studies were reported by Knapp,&apos; Anderson2 and Kirwan." These studies were the first to be reported in the literature on this subject. No further information was published on the subject until 1932 when Rubel&apos; presented a paper in which he discussed the effect of drilling fluids on oil well productivity. In 1935. .Jones and Babson constructed the first laboratory tester designed to study the effects of temperature and pressure on the filter loss behavior of clay-water drilling fluids. In a discussion of their investigations, Jones and Babsons stated, "Performance characteristics of a mud can he evaluated with considerable reliability by a single test at 2,000 psi and 200°F. Exact correlation between the results of performance test5 made under these conditions and the behavior of muds in actual drilling operations is of course impossible." Jones arid Babson apparently were well aware that at best laboratory tests can give only qualitative answers to the question of what is the actual behavior of a drilling fluid when subjected to deep drilling conditions. Jones&apos; presented a paper in 1937 in which he described a static filter loss tester to be used for routine filter loss tests. This instrument subsequently was adopted as the standard APl filter loss tester. In 1938, Larsen7 developed a relationship between filtrate volume and filtrate time that is in general acceptance today. Larsen was cognizant of the danger of estimating bottom hole behavior from filter loss measurements at room temperature. He tried to predict the effect of temperature on filter loss by relating temperature effects through the temperature dependence of filtrate viscosity. This was undoubtedly an over-sirriplification of the temperature dependence of drilling fluid filter loss. In 1940, Byck" published a summary of experimental results of filter loss tests made on six representative California clsy-water drilling fluids. He concluded that "no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied." Byck&apos;s findings were presuma1)ly well accepted and recognized by drilling Fluid technologists, and yet, they did not lead to wide adoption of high temperature drilling fluid filtration equipment. This is evidenced by the fact that no addition information has appeared in print on the subject since 194). Study of Byck&apos;s data shows that there was a useful consistency in them. The fluids did not show predictable losses at high temperatures, but they did line up at high temperatures in approximately the same order that they lined up at low temperatures. That is, if a fluid appeared to be a good fluid with relatively low loss at low temperatures, it would also be a good fluid with relatively low loss at high temperatures. In the last decade. the above situation has changed. The drilling fluid art is markedly different from what it was. The outstanding change, as far as the present discussion is concerned, has been the adoption of wholly new types of drilling fluids. Oil base and emulsion drilling fluids have come in to wide use. It is, therefore, necessary- to re-examine previously satisfactory generalizations to see if they are still valid. It turns out. as might have been expected. that Byck&apos;s explicit generalization. already quoted, is still true. Filter losses at high temperatures cannot be predicted from filter losses at low temperatures. However, no further generalizations are valid now. Fluids of different chemical types show different general behaviors. No longer do the fluids line up approximately the same at high temperatures as they do at low temperatures. They may line up entirely differently. Special fluids exhibiting very low loss at low temperatures may have losses as high as those of ordinary clay-water fluids at high temperatures. This fact is highly significant, because premium prices are being paid for the special fluids.

Jan 1, 1952

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,&apos; and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6&apos;7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.&apos; EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.&apos; Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969