Search Documents

By Morris Muskat, James M. McDowell

A report is given of electrical analog experiments on the effect of casing perforation completions on well productivity for ideal uniform reservoirs under steady state homogeneous fluid flow conditions. Graphical results are presented for the effect of perforations of different densities and various degrees of penetration into the formation surrounding the casing or cement sheath. The latter range from perforations which terminate flush with the casing to those which extend into the formation a distance equal to the casing diameter. For the special case where the perforations terminate immediately beyond the casing with semi-spherical protrusions the electrical analog results correct and supersede previously reported theoretical calculations. It is found that the penetration of the perforations into the surrounding productive section may so increase the resultant productivity as to approach or even exceed that for open hole completions. INTRODUCTION A theoretical analysis of the effect of casing perforation on well completion, without additional penetration of the formation, was reported several years ago.' In this treatment the perforations were represented by mathematical sinks and no explicit account was taken of the imperviousness to flow of the casing in which the perforations were made. This procedure was justified by consideration of the mutual interference between the sinks, which seemed to indicate that the analytical method automatically eliminated flow across the casing radius between the perforations. However, both further theoretical investigation and the electrical analog measurements described below showed that this assumption in the previously developed theory was not valid and that the calculated well capacities would considerably exceed the correct values. § Even if this simplifying assumption were retained the generalization of the theory to situations where the perforations extend into the producing formation would be extremely difficult. On the other hand, the electrolytic model analog of this type of steady-state homogenous fluid system is, in principle, so simple that it has not been worthwhile to attempt to develop the exact analysis even for the more limited case of strict casing perforation. The whole problem has therefore been studied anew by electrical models to cover the range from holes in the casing which terminate flush with the casing surface to such as extend into the surrounding rock to a depth equal to the casing diameter. It is to be expected that the productivity of a well completed with casing radius* rw, perforated with holes of radius Tp, and extending to depths d into the surrounding rock, would depend primarily on the dimensionless geometrical parameters Te Tw TP d of the system, such as —, —, — , and —, where re is the Tw, a a rw external boundary radius and a is the mean vertical separation between the perforations. It will also depend, of course, on the number of perforation lines or total perforation density. While such parameters automatically control analytical treatments, it would require a very extensive series of model experiments to fully disclose their functional effect on the well productivity. For practical purposes, however, a rather limited range of the variables suffices to give the effects of interest. Accordingly, in the experimental study reported here the casing diameter has been kept fixed? at six in., the perforation diameter has been taken as either one-fourth in. or one-half in., their density has been varied from one to eight per ft, and their penetration into the formation has ranged from zero to six in., with a primary scaling factor of one to six. EXPERIMENTAL METHOD AND RESEARCH Although electrolytic model experiments have been made for years, there still seems to be some question as to what set of conditions will give the best results. For this reason a number of electrode materials and electrolytes were tried. Those chosen for the final experiments were copper electrodes and a weak copper sulphate solution as the electrolyte. This 'Assuming that the casing has been cemented with a uniform and impermeable cement sheath, the effective casing radius is to be interpreted as the external radius of the cement annulus. It is also assumed here that the casing is set through the complete producing section that it is perforated throughout with a uniform density and that tie formation has a a and isotropic permeability. As noted later, however, a uniform scale change permits reinterpreting the primary measurements to correspond to a casing diameter of 12 in.

Jan 1, 1950

By P. Martinez, A. F. Hoyte, F. E. Senftle

The possibility of applying a neutron activation technique for silver exploration is considered. A mobile positive-ion accelerator type neutron source is used to irradiate a small area of rock or soil in situ. By using a short period of irradiation and gamma ray spectral analysis, a technique is shown for silver exploration. Two different mobile units are described. Laboratory and preliminary field tests both indicate that a sensitivity of less than 1 oz of silver per ton of ore can be achieved. The increasing consumption of silver for industrial uses and also for coinage has caused a serious shortage of silver in this country. The silver shortage has been reviewed and analyzed by kiilsgaard1 who concludes that, "The best hope for meeting future demands for silver is through accelerated exploration for precious ores." As almost all the exposed "bonanza" type silver deposits evidently have been found, it is urgent that some sensitive geophysical technique be found to detect large, extended, but generally low-grade, secondary ores, as well as hidden vein deposits. Silver is easily made radioactive by exposure to slow neutrons; hence a neutron activation method appears promising for locating silver deposits. The principles of mineral beneficiation using neutron activation techniques were discussed some years ago.2-4 Using the same approach, a preliminary description5 has been published of neutron activation as a mineral exploration tool. An exploration technique is described in which silver is made radioactive in situ and detected with a gamma radiation counter. The technique is similar to the well-known method used for uranium exploration. THEORETICAL CONSIDERATIONS Elemental silver consists of two isotopes, Ag107 and Ag109, having naturally occurring isotopic abundances of 51.4% and 48.6%, respectively. For short periods of irradiation of silver by thermal neutrons, the long-lived 250 day, half-life isotope, Ag110m, is not produced in significant quantities. However, significant quantities of 2.3 min half-life Ag108 and 24.5 sec half-life Agl10 are formed by the following reactions. Ag108 and Agl10 emit a 0.44 Mev (million electron volts) and a 0.66 Mev gamma ray, respectively. Ag107 + n + Ag108 (2.3 min) Ag109 + n + Ag110 (24.5 sec). Because of the large capture cross section (110 barns) of Ag109, and short half-life of Ag110 (24.5 sec), the 0.66-Mev gamma ray is the most prominent emission from silver for neutron activation periods of about a minute's duration.* The 0.44-Mev gamma ray from Ag108 will also be present, but will be one or two orders of magnitude lower in intensity. The decay scheme of Ag110 is shown in Fig. 1. If the neutron irradiation time is limited to about 100 sec, the Ag110 activity will essentially reach saturation and can be used to detect the presence of silver. In a neutron flux of 10 8 neutrons/cm2/set, the induced 0.66-Mev activity in 1 g of silver will be about 2 x 107 disintegrations per sec. This is about 1000 times the measurable gamma activity of 1 g of uranium in equilibrium with all its decay products; hence there is ample activity for detection. Under the same conditions of activation, most of the other elements do not reach this relatively high disintegration rate. Although this is in favor of the proposed technique, other problems must be considered. For mobile operation, it is desirable to obtain the largest neutron flux to weight ratio. Hence we have used a small 150-kev accelerator-type neutron source rather than an isotopic source such as an americium-beryllium neutron source. By use of remote control system, an accelerator-type neutron source can be safely used without the massive shield required for an isotopic source. Moreover, an accelerator-type source is more versatile in that it allows one to use a flux of either 14-Mev or 3-Mev neutrons, depending on whether a tritium or a deuterium target is used. With a 14-Mev generator, one can obtain a flux of 10 9 neutrons/cm 2/sec, and with a 3-Mev generator, the flux is generally two orders of magnitude less. Although silver will become activated with either generator using proper moderation, detection may be

Jan 1, 1968

By J. C. Cook

In solution-mining of underground salt and similar minerals, using drilled wells for access, it is desirable to monitor the lateral growth pattern of the resulting fluid-filled cavern. Therefore, a process of seismic surveying from the surface of the ground has been conceived in which the amplitudes of waves reflected from and transmitted through the soluble formation are measured. The large acoustic impedance contrast between solid and fluid should produce striking amplitude anomalies, especially if shear waves are employed, since thick fluid bodies are opaque to shear waves. Horizontally-polarized (SH) shear waves are best for preventing conversion to P waves at the numerous horizontal interfaces in the ground. Field tests to date have shown that a truck-mounted, half-ton hammer striking horizontally against the end of a trench produces usable SH-wave energy at lateral distances up to about 850 ft. Horizontally-directed explosive wave sources were effective to about 2000 ft. Conventional magnetic-tape recording and processing were used, but with the detecting geophones oriented to favor SH waves. An irregular solution cavity in bedded salt at 500-ft depth has apparently been located by SH-wave and SV-wave reflections. Further field work is planned to corroborate and extend this result. The Brine Cavity Research Group, an association of 11 chemical and salt producing companies, is supporting this work. Major deposits of salt in tabular beds lie beneath some 300,000 sq miles of land in the central and northeastern U.S. This salt is a basic source of soda ash and chlorine, and has been extracted as brine from drilled wells for about a century. During the past two decades, the U.S. solution-mining industry, following the lead of European operators, has greatly improved the extraction process through the application of engineering and science.' In 1957, the Brine Cavity Research Group, an association of 11 chemical and salt producing companies, was formed. This group proceeded to attack certain common problems through the support of research. An outstanding problem has been that of determining the shape and location of the growing solution cavities in the underground salt, so that measures can be taken to maintain operating efficiency. The problem has been partially solved by the Dowel1 sonar mapping service, which employs a pulse-echo device lowered into the cavity through the well.2 However, the working range of this equipment is at present insufficient for large cavities, and echoes are not returned from highly sloping walls nor from behind such obstructions as rock debris. Therefore, an independent means of mapping the cavity, for example, from the surface without interfering with operation of the well, would be desirable. THEORY OF THE METHOD Seismic waves are the only physical agent known to be capable of sufficient resolution and penetration to define typical solution cavities from the surface of the ground. The geometry is unfavorable: cavity widths are generally less than half their depths below the surface; resolution and lateral location of boundaries and channels to within 50 ft at depths of 500 to 3000 ft is desirable. Conventional seismic surveying, as used for petroleum prospecting, is probably not the answer: isopach mapping, for example, is not thought accurate enough to define the cavity by the slight additional delay time it would introduce (of the order of 0.005 sec for a 50 ft-thick cavity in hard Paleozoic rocks). Refraction surveying has also been considered, but seismic specialists see little promise in it for this problem. In 1957, in correspondence with industry personnel, the writer suggested a seismic method based upon careful measurement of reflection amplitudes. As Table I illustrates, seismic reflection coefficients r for typical brine-rock interfaces are considerably higher than those for typical interfaces between different kinds of solid rock. This fact can be utilized in two ways, illustrated in Fig. 1: 1) If the cavity roof is reasonably flat (which it may sometimes be since the unsaturated top brine will be in contact with an insoluble rock stratum), extra-strong seismic reflections will be received from the salt stratum where the solid has been replaced by liquid.

Jan 1, 1964

By B. J. Kochanowsky

TO improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi; Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,2 editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature." Present blasting theory is based upon two assumptions. 1) The blasting force of explosive acts in concentrical and spherical form. 2) Rock resistance against the explosive force is directly proportional to the strength characteristics of the rock. The first classical formula based on theoretical fundamental in blasting theory for explosive charge calculation was introduced by Vauban, a military engineer who lived 300 years ago. It was Vauban who proposed the famous formula L = w3 q, where L is the explosive charge, w = line of least resistance, and q = specific explosive consumption proportional to the weight of rock. Later engineers used q as proportional to the strength of the rock. Since Vauban's time different suggestions concerning blasting theory have been proposed. However, the principles stated at that time so affected the thinking of later generations that his formula is still in use and practically unchanged. The first controversy concerned the form of crater. It was found that geological features of rock affected its form. The factor q was analyzed thoroughly by Lares3 and later by Ohnesorge," Weichelt,5 Bendel,6 and others, but the assumption remained that resistance against explosive force is directly proportional to the strength of the rock blasted. The greatest controversy, which has not yet been settled, concerned w. It was noted that w3 is more appropriate for long lines of resistance and w2 for lines of resistance less than 15 ft. Based on the assumption that the explosive force acts concentrically and spherically, spacings between charges were limited to distances not greater than the length of line of least resistance. Sometimes larger spacing is recommended, but this is due to the advantageous geological and physical properties of rock and not to the action of an explosive force as such. In addition to the classical formula, empirical formulas are used widely. These state that the explosive charge is directly proportional to the volume of blasted rock in cubic yards, and the amounts of explosive required are usually expressed in pounds of explosive per cubic yard of rock. Empirical and classical formulas are contradictory. In the empirical formula, but not in the classical formula, explosive charge is taken proportional to all three space axes: line of least resistance, spacing, and bench height. In spite of this contradiction, both formulas give good results. This is possible because as now practiced the explosive charge calculation for heavy burdens need not be highly accurate. Each, open pit or quarry, usually works with a certain relation between bench height and line of least resistance and between charge spacing and line of least resistance. When these relations are changed, however, the specific explosive consumption q changes greatly. This is one of the reasons why the principles on which the formulas are based appear to be incorrect. In addition to the formulas discussed, others exist and are based more or less on the same theoretical

Jan 1, 1956

By H. A. Hoffman

Competition from an all-flotation plant, with demonstrated economies and efficiencies, plus a change in smelting contract and introduction of improved cyclones lead to conversion from gravity-flotation. Detailed descriptions are given of equipment installed and procedures used at St. Joseph Lead's Federal mill. Future plans include further quality control by instrumentation in all aspects of the mill operation. Also planned are improvements in materials handling systems. Competitive conditions will continue to dictate improvements and changes in the mill flowsheet. The advent of all-flotation mills in the Lead Belt was introduced by the Indian Creek mill in late 1953. This modern and efficient plant then became a pattern for the other mills in this area to re-evaluate their circuits in an effort to develop flowsheets that would improve operating conditions and metallurgy. The Indian Creek mill demonstrated that all-flotation would require considerably less operating and maintenance labor than the combination of tabling and flotation that was common in the Lead Belt at that time. Two significant changes occurred in recent years to allow all-flotation to be seriously considered in other Lead Belt mills. One was a change in the smelting contract which did not require gravity concentrate. Another was the development of cyclones which provided classification of the flotation feed in a very small space. Since the Federal mill was the largest concentrating plant in the Lead Belt it was felt that the greatest savings could be made by investigating the all-flotation possibilities at this mill. Interest was stimulated by the milling and ore dressing Depts. to determine if this mill would be converted without undue cost, provided the metallurgy could be improved. Accordingly, laboratory tests were initiated to learn what metallurgical benefit could be derived. Numerous tests were run which indicated that grinding to all-flotation would improve the tailing by as much as 0.02 pct Pb. This was quite significant when multiplied by the tonnage of ore treated. Projecting the added cost of power for extra grinding and flotation, and the additional flotation reagents required, plus additional new equipment that would have to be purchased, it would still add up to a considerable saving. The all-flotation mill would reduce man power by some 30 pct, and make a metallurgical improvement. Operating costs could be reduced bv 2$ per ton. The metallurgical improvement would amount to 4$ per ton, for a total of 6$ per ton of ore milled. An estimate of the cost of the conversion was set at $250,000. With the savings as estimated this could be paid off in about two years. On paper it therefore seemed attractive enough to justify a mill test. MILL TESTING One section of the Federal mill was made available for use as a separate test circuit. Cyclones and density controllers were borrowed from the Viburnum and Indian Creek mills. Denver flotation cells were obtained from the Desloge mill that was then shut down. Two 10-cell groups of Fagergren flotation machines, consisting of eight roughers and two cleaners in each bank, were segregated from the remainder of the plant. The 9x12-ft rod mill was continued as a primary grinding mill. The two 6%x12-ft mills on this section were converted from rods to balls, and the speed increased to 22.0 rpm. Cyclones were installed to close the circuit of these ball mills. The ground pulp from each of the ball mills was fed separately to its own bank of flotation cells so that two completely separated test circuits could be run in parallel. This test circuit operated on a three-shift basis from Dec. 22, 1959 to Mar. 21, 1960. The first few weeks were occupied in developing conditions for proper metallurgy and trouble-free operations. Results were rather erratic but as the ore dressing laboratory and the mill operators became more familiar with conditions they were able to obtain expected results, which could be duplicated day after day. The last five weeks of testing indicated the best results and are tabulated in Table I. During the first two weeks a Denver unit cell was used on No. 1 flotation circuit. Even though it recovered almost one half of

Jan 1, 1962

By D. E. Swets, R. C. Frank

It is well known that hydrogen is introduced into iron or steel as a result of many chemical processes (acid pickling, electrolytic cleaning, plating, etc.). One of the reactions that has been of recent interest1 is the reaction between an iron surface and water vapor. It was shown a few years ago2-4 that hydrogen can be introduced into steel at an accelerated rate during abrasion as a result of this reaction. Grun-berg and Scott have also observed that water in mineral oil lubricants increases pitting failure in ball bearings5 and they have suggested that hydrogen from the water is the primary cause of this effect.' In this laboratory, the question was raised as to whether or not hydrogen is also introduced into the metal surface of a bearing as a result of the decomposition of the hydrocarbon lubricant itself, and an experiment was performed to try to find a satisfactory answer. All steel parts contain some residual hydrogen. Therefore, it appeared that the best way to carry out this experiment without the need for highly accurate quantitative analyses was to use deuterium as a tracer. The natural abundance of deuterium in H2 is only 0.015 pct. The tracer was obtained in the form of deuteroparaffin (CD,(CDJ, CD,) and 0.25 g were dissolved in 20 cc of mineral oil to form the lubricant to be used in the tests. The bearings used were New Departure Type QOLOO ball bearings with a ball diam of 0.187 in. Prior to adding the mineral oil-deuteroparaffin lubricant, the bearings were cleaned in warm trichloroethylene to remove the packing grease. After packing with the new deuterated lubricant, the bearings were operated in a bearing fatigue test machine under a radial load of 190 lb and a thrust load of 190 lb at a speed of 3800 rpm. The expected life under these conditions is about 500 hr. Two tests were made; one for a period of 27 hr and the other for a period of 102 hr. The bearings achieved a temperature of 120o F during the tests. When the tests were stopped the balls were mechanically removed from the bearings and were immediately placed in liquid nitrogen to reduce degassing until the analysis for deuterium could be made. Before analyzing, the balls were warmed to room temperature and scrubbed with several degreasing agents to remove all traces of the deuteroparaffin mixture. This cleaning procedure was shown to be satisfactory by running a control test in which one ball bearing was subjected to all parts of the test except running in the fatigue machine. The hydrogen and deuterium were removed from the balls using a hot extraction apparatus attached to a mass spectrometer. Four balls from each bearing were analyzed. Each one was analyzed separately by removing it from a cold storage volume of the hot extraction apparatus and transferring it to the oven tube with a magnet. As the gases were evolved they were analyzed with the mass spectrometer. Since the hydrogen and deuterium pass through steel in the atomic form and since there are many more hydrogen atoms than deuterium atoms in the sample, the probability of forming an HD molecule is greater than forming a D2 molecule. For this reason the evolution of HD and H was followed as each ball was placed in the oven. The results showed that as each ball from the test bearing was dropped into the oven, the mass spectrometer recording of the HD evolution increased by about ten divisions. When balls from the control test bearing were dropped into the oven, the increase was about one division or less. The hydrocarbon background in the mass spectrometer was also monitored to see if hydrocarbons or deuterocarbons were given off when the balls were dropped into the oven, but no change in the hydrocarbon peaks was observed. Since the balls contained a fair amount of residual hydrogen, isotope ratio measurements were made on the gas obtained from each ball. The D/H value found for those balls which had been operated in the fatigue testing machine was consistently about 0.3

Jan 1, 1962

By W. E. Newell

The basic principles and assumptions involved in D. L. White's solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.' In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-' and semi-conductor, and current saturation in piezoelectric semiconductors.'4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-'. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.' The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962

By R. Bruce Tippin

Background Iron ore is the No. 1 metal mining industry in the U.S. with dollar value of $2.3 billion in 1984 (U.S.B.M Mineral Commodity Sunnnaries , 1985). However, during the past decade this nation's iron ore industry has been subjected to a major market depression and a correspondingly downward adjustment in output. The recent trend in the curtailment of iron ore production traces a slow-down of the country's steel industry. Both pig iron and steel production have decreased significantly over the past several years. These trends are shown in Figure 1 from data collected by the federal Bureau of Mines (U.S.B.M. Mineral Commodity Summaries, 1985; U.S.B.M. Mineral Industry Surveys 1986). The industry is presently operating at less than 60% of its annual capacity. The domestic steel industry has been forced by reduced profits or losses to close facilities, curtail operations and restructure the financial status of several corporations. Companies have been sold or are trying to sell selected properties to improve their financial circumstances. Even with such actions, many of the steel companies are in very serious straits, including the seventh largest steel company, LTV, which has filed for bankruptcy. Many of the major steel companies have financial interests in iron ore mining and thus their adverse economic conditions directly reflect those operations. Several iron ore producers have been shut down including Reserve Mining Company in May, 1986 and Butler Taconite in June, 1985. The latter recently filed for bankruptcy under Chapter 11. A1 so in mid-1986, U.S. Steel Corporation, owner of the Minntac mine and iron ore processing plant, underwent corporate restructuring. The effect on their Minnesota plant is not known at this time. An excellent summary of the interrelationship of the iron ore companies and the steel producers has been provided by Skillings (1986), and an analysis of the iron ore situation was given by Robert F. Anderson, CEO of M. A. Hanna Company, in his keynote address at the 1986 University of Minnesota Mining Symposium (Anderson, 1986). Steel imports to the United States decreased slightly in 1985 because of import restrictions, but the long-term import situation remains dim and uncertain. As shown in Figure 2, the imports averaged about 25% in 1985, and the preliminary indications are that this figure could be as high as 30% when the final 1986 information is collected by the U.S. Bureau of Mines. At best, the industry can only hope for imports to stabilize at a constant level in the near future. Although the tonnage is small, the quantity of U.S. export steel has fallen over 50%. With many other materials replacing steel , the projected demand through 1990 is expected to increase only about 1% per year. Consequently, 1986 U.S. iron ore production will probably be 15% lower than in 1985. The 41 mil lion tons of iron ore production expected in 1986 represents only 53% of the industrial capacity, which is about 74.5 mil lion tons. Over 95% of this iron ore is in the form of beneficiated pellets. Today there is not an iron ore producer west of the Mississippi River, nor is there any production in the South. The Birmingham (Alabama) iron ore industry has been shut down since 1971. The western producers ceased operations in the early 1980's. Only the taconite operations in Minnesota and the plants in the Upper Peninsula of Michigan remain as our major domestic iron ore source. The economic situation for both the iron ore producers and the steel industry can be described as confused and in turmoil. Such a condition directly impacts the iron ore processing plants' operations and plans for the future. Plant Practice At present the nation's eight major operating iron ore mines, listed below, are concentrated in northern Minnesota (Mesabi Range) and the Upper Peninsula of Michigan (Marquette Range). The only exception to the Minnesota/Michigan location is the Pea Ridge Iron Ore plant in Missouri, which is a subsidiary of St. Joe Mineral s.

Jan 1, 1986

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,' and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

By R. H. McLean

Jet impingement produces two mechanisms to clean the bottom of a borehole during jet-bit drilling operations. One is an impact-pressure wave in the immediate area of jet impingement. The other is crossflow, which spreads across the bottom away from the pressure wave. Measurements of the vertical distribution of the cross-flow at several positions beneath a 4 3/4-in. tricone jet bit in a laboratory model show that the maximum velocity in the crossflow is directly proportional to the square root of the product of the rate of flow and the velocity of the jets through the nozzles (QV). Other measurements in the laboratory model show that gradients in the impact-pressure wave are directly proportional to the jet QV if the diameters of the nozzles are held constant. Consistency of the basic relationships through changes in the Reynolds numbers of the jets from 31,000 to 93,000 suggests that the laboratory results should be representative of typical flow in field operations having higher Reynolds numbers. Estimates of the impact-pressure waves under conditions other than those in the jet-bit model may be made by comparison with a less complex model—impingement of a jet against an unrestricted flat surface normal to the jet. Equations derived from current jet technology describe the wave in this simple system for a wide range of conditions. INTRODUCTION The efficiency of rotary drilling operations is strongly linked to the efficiency with which cuttings are removed. Cuttings remaining on the bottom of the borehole will impede further penetration by the bit until they are removed. Wasteful regrinding is prevented if the fluid circulated past the bit removes cuttings as rapidly as they are made. Most investigations of bottom-hole cleaning under bits have been concerned with the rate-of-penetration effects of bit type, nozzle configuration, fluid properties, pressure gradients and utilization of hydraulic horsepower. These investigations have shown that drilling muds, weighted to keep the pressure in the borehole greater than in adjacent formations and carrying material which forms a filter cake, apparently plaster cuttings against the bottom, making them difficult to remove. In addition to a demonstration of the factors causing poor cleaning, the most significant result of these previous investigations has been the increased use of jet bits accompanied by better hydraulic programs and better selection of drilling fluids. Undoubtedly, these practices have improved bottom-hole cleaning, but rates of penetration when drilling with muds are still often lower than would be expected with perfect cleaning." Although there is general agreement with the concept that increasing hydraulic energy at a jet bit often increases the rate of penetration by improving cleaning, research workers have differed as to the best criterion for evalyating hydraulics. Some lean toward maximizing the product of the rate of flow and the velocity through the nozzles (QV) others prefer to maximize the hydraulic horsepower at the bit;'"-' "till another says that neither criterion is universally suitable."' This controversy shows that conclusive field evidence has not established the superiority of either of these criteria. Analysis of the fluid flow which cleans the bottom should contribute to resolving the controversy. Impinging jets clean the bottom by creating two mechanisms capable of dislodging cuttings. One is the impact from the momentum of the jet and the other is the flaw parallel to the bottom away from the area of impingement. The impact force appears in the form of a pressure wave on the bottom and, in this paper, is called the impact-pressure wave. The flow parallel to the bottom is called crossflow. Fig. 1 illustrates these two mechanisms. This paper describes crossflow and the impact-pressure wave beneath jet bits and relates them to controllable parameters. Through these relations, criteria for use in designing hydraulics to achieve maximum use of the mechanisms of cleaning are derived. PROPERTIES OF CROSSFLOW CONCEPTS DEVELOPED IN PREVIOUS INVESTIGATIONS Concepts of scavenging the bottom by crossflow have been well discussed by Bobo, et al." They examine the means by which crossflow may create forces on cuttings and conclude that the cleaning action of crossflow can be increased by increasing the velocity of the flow stream close to the bottom. Using boundary layer theory, they indicate that a reduction in the viscosity of the drilling

Jan 1, 1965

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

The formation density logging tool provides a radioactivity measurement that yields formation densities in situ. The relationship between bulk density and porosity is well understood. With knowledge of grain and fluid densities, porosity may be computed from the indicated formation bulk densities in shale-free formations. The porosities thus determined may be used with a resistivity log for water-saturation determinations. One technique utilizes a density vs resistivity plut. A plot of density vs Sonic-log transit time is used for porosity determinations in shaly sands. This method is particularly suited to wells drilled with oil-base or salt muds. In shale-free formations, comparisons of density values nnd neutron-log readings are used to identify lithologr and, thus, to select appropriate values of grain density for porosity computations. Through the use of Formation Density, Sonic and neutron logs, the interpretation problems caused by complex matrix lithologies are simplified. Other applications of the Formation Density log are found in the identification of minerals in evaporite deposits and in yield determinations of "oil shales". INTRODUCTION Widespread field application has demonstrated that the measurement of formation density is a useful and revealing technique for well logging. Responding to the bulk density variations of the formation, the Formation Density log affords valuable data on the porosity, lithology and fluid content of the formations. Although not without its own limitations, the Formation Density tool may provide effective interpretation under conditions that hamper or preclude the use of other porosity devices. When used in conjunction with other devices, such as the Sonic or neutron, complex matrix conditions may be better understood, defined and evaluated. A previous paper' described the valuable contribution of the Formation Density tool in the logging of empty, or gas-filled, holes. The purpose of the present paper is to describe applications of the device in liquid-filled holes. THE FORMATION DENSITY TOOL The Formation Density tool was devised to measure the bulk densities of formations in situ. Actually, the device responds to electron density, but in the overwhelming majority of cases of interest, the electron density is very closely proportional to the bulk density. In other cases appropriate corrections can be made if necessary. Comparisons of log-derived densities with true densities for the more common matrix minerals are shown in Table 1. The tool consists of a gamma-ray source and detector mounted in a skid which, during the logging operation, is in contact with the borehole wall (see Ref. 1 for schematic). Gamma rays are emitted by the source and diffused through the formation. The number of diffused gamma rays reaching the detector at a fixed spacing from the source are counted. An increase in counting rate by the detector indicates a decrease in bulk density in front of the skid. Conversely, a decreased counting rate signifies an increase in bulk density. A measurement of hole diameter, between the face of the skid and that of the eccentering arm, is recorded simultaneously with the measurement of diffused gamma rays. Since the tool is a wall-contact device, the size of the borehole has little influence, provided good contact is maintained with the wall of the hole. Only in extremely large or small boreholes does the actual diameter become significant. However, for most accurate measurements the borehole size should be taken into account. Fig. 1 presents the departure curves for the conversion of counting rate to bulk density for liquid-filled holes of various sizes. It is of utmost importance that the skid maintain good contact with the wall of the hole. If, due to roughness or caving, there is mud between the skid and the formation, the tool will include in its response the relatively low-density mud, and the apparent density reading will be too low. Normally, permeable beds do not cave appreciably, so that reliable readings are usually available for zones of interest. Nevertheless, the caliper reading over the zone of interest should be examined for any wall roughness. When mud cake exists between the skid and the formation, the Formation Density log sees it as part of the formation. When thick mud cakes exist, a correction is required. For best results in wells having thick mud cakes,

By A. Kenneth Schellinger

THE terms surface tension .and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the minerals present.. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to. 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid: liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1952

By R. J. Charles

SEARCH for a consistent theory to explain the relationship between energy input and size reduction in a comminution process has accumulated, over the years, an enormous amount of plant and laboratory data. Although some correlation of these data has been possible for purposes of engineering design and for the advancement of research in fracture, there is still great need of a means of predicting behaviour of a solid when it is reduced in size by mechanical forces. The best known hypotheses proposed to describe the energy-size reduction relationships in crushing and grinding stem from a common origin. The present article analyzes problems of comminution in the light of the precepts of this origin. Its object is to reconcile points of difference between these well known hypotheses and to present relationships more widely applicable to comminution studies. Theoretical Considerations: Most existing relationships between energy and size reduction of a brittle solid stem from a single, simple, empirical proposition.&apos; Although this proposition can be demonstrated by observation and experiment, no theoretical derivation is yet possible. Mathematically, the proposition may be stated as follows: dE = -Cdx/xn [1] where dE = infinitesimal energy change, C = a constant, dx = infinitesimal size change, x = object size, and n = a constant. Eq. 1 states that the energy required to make a small change in the size of an object is proportional to the size change and inversely proportional to the object size to some power n. No stipulations are placed on the exponent n in either magnitude or sign. In 1867 Rittinger2 postulated that the energy required for size reduction of a solid would be proportional to the new surface area created during the size reduction. As far as can be determined there is as yet no physical basis for Rittinger&apos;s hypothesis. Rittinger&apos;s hypothesis can be stated mathematically as follows: E, = K(oa-a-0 . [2] Er = energy input per unit volume, K = a constant, <ti = initial specific surface, and o2 = final specific surface. In the size reduction of particles of size x, to particles of another smaller size, x2, Eq. 2 becomes the well known relation: ET = K&apos; {l/x2-l/xx) [3] where K&apos; is a constant. Eq. 3 may be arrived at from the proposition given in Eq. 1 by integrating and by assigning a value of 2 to the exponent n. J dE = J - C dx/x2 E = Kt (1x - 1x) where K&apos; = C. In 1885 Kick3 proposed the theory that equivalent amounts of energy should result in equivalent geometrical changes in the sizes of the pieces of a solid. For example, if one unit of energy reduced a number of equal-sized particles to particles of one half the size, then the same amount of energy applied to the particles resulting from the first test should result again in a size reduction of one half or a final size one quarter the original size. The Kick concept may be expressed as follows: Ek = K" log x1/x2 [41 K" = a constant and E, = energy per unit volume. The expression for Kick&apos;s law may be arrived at by again integrating Eq. 1 and in this case assigning a value of 1 to the exponent n. dE= J - C dx/x Eh = - C In {x/x2) = K" log (x,/x,) where K" = 2.3 C. Application of Kick&apos;s and Rittinger&apos;s laws to comminution has met with varied success. Gross and Zimmerley4 and Piret5 have shown that Rittinger&apos;s equation applies under certain conditions of experimentation. Walker and Shaw6 express the belief that in metal turning and shaping and in grinding of both metals and minerals the production of very fine particles (less than lP) follows Kick&apos;s hypothesis, whereas Rittinger&apos;s concept is valid for the size reduction of coarse particles. For the practical case of crushing and grinding, however, neither of the above hypotheses has received general acceptance. Bond&apos; has lately proposed that since neither Kick&apos;s nor Rittinger&apos;s hypotheses seem correct for plant design work, an energy-size reduction relationship somewhere between the two would be more applicable. The fundamental statement of Bond&apos;s work

Jan 1, 1958

By R. A. Greenkorn

This project originated in a practical problem—we needed five tracers that could be used together to locate flow paths in a pilot flood. While tracers for subsurface liquids have been used since the turn of the century,1-15 none of those reported in the literature appeared to be either consistent or quantitative enough for our purposes. Most were used in field systems without controlled experiments to determine the accuracy and precision of analysis, and many were tracers that could not be used collectively. The ideal tracer, of course, would follow the fiuid of interest exactly, traveling at the same velocity as the fluid front. But the ideal is impractical to attain because adsorption-desorption effects cause the tracer to lag behind the front; these effects, plus diffusion-dispersion effects, cause the tracer front to spread more than the fluid front. Thus, our objective was not to locate a tracer that would be ideal for all circumstances but rather, to find one that would approximately follow the fluid, or one that under controlled conditions could be corrected to calculate the movement of the fluid front. We considered tracers satisfactory—(1) if they were easy to analyze; (2) if their breakthrough-elution curves were not too different from those for the chloride ion, a tracer believed to follow the fluid front closely; and (3) if we could calculate from the curves a material balance, at 1.25-PV (pore volume) injected, within 5 per cent of that calculated from chloride curves. Of a possible 35 materials, we selected 13 tracers that could be quickly and easily identified and whose analysis was claimed to be accurate within 5 per cent. Only one of these, tritiated water, was a radioactive tracer. Radioactive tracers are easy to detect even in small quantities, but they require special handling and special equipment. Also, those that can be used together are limited because special equipment is required to separate emissions from the various tracers. Two of the original 13 tracers were eliminated in static tests to determine how accurately and precisely they could be analyzed, and to check on gross adsorption. The remaining 11 were flowed through a 9-ft linear sandstone model, and breakthrough-elution curves were obtained. Finally, three tracers were field-tested as breakthrough tracers. These tests are described in the following sections. The 13 tracers considered in these experiments were EDTA (ethylene diamine tetra acetic acid), fluo-rescein, picric acid, salicylic acid and ammonium, boron (as borate), bromide, dichromate, iodide, nitrate and thiocyanate ions, plus chloride ion and tritiated water. All but the chloride ion and tritiated water were subjected to static sand tests to eliminate the tracers that could not be analyzed quickly and accurately and to eliminate those that showed excessive adsorption. All but two of the tracers, EDTA and salicylic acid, qualified for flow tests on this basis. The procedures used in the static tests (see Appendix A for analytical details) were as follows. Each tracer (in the amount shown in Table 1) was dissolved in 1,000 ml of water. Then, 800 ml of this solution was added to 500 gm of sand, and the remaining 200 ml was reserved as a control standard. The sand-tracer mixture was agitated once a day over a 10-week period, and during this period we analyzed five duplicate samples from this mixture, along with five duplicate samples from the control solution. From the control-sample analyses, we constructed a control chart on which the sand-tracer analysis results were plotted. The control chart, and its use to determine accuracy and precision of analytical results, as well as the amount of adsorption, is described in Appendix B. The results of the static tests are summarized in Table 1, which lists the concentration c (concentration at time t) divided by c, (initial concentration). If there was no adsorption, c/c, = 1. The acceptable deviation from this value varied from tracer to tracer, depending upon the limits of analytical precision established for the different tracers. The best results were obtained with boron, bromide and dichromate, with all values falling within limits of accuracy and precision. Ammonium, iodide, nitrate and picric acid also were satisfactory, although the ammonium results were erratic. Flourescein and thiocyanate were unsatisfactory ini-

By J. B. Wagstaff, R. A. Buchanan, J. F. Elliott

High speed photography through blast-furnace tuyeres showed coke particles moving rapidly. Model studies showed a raceway was formed and gave quantitative results which were correlated with actual blast furnaces. Another study showed the similarity between hanging and the flooding of a packed column. This was explored by models. THE combustion zone before the tuyere in an iron blast furnace is a vital region because here are generated: 1—most of the gases on which the furnace depends to carry out its basic operation of reducing iron ore to the metallic state, and 2—the major fraction of the heat required in the nearby regions of the furnace for the various reduction reactions, the fusion of the slag, and the melting of the iron. Since the greater part of the coke is consumed in this region, the descent of the burden must be greatly affected by the characteristics of the tuyere zone. This region then would seem to be a profitable field for study. Fortunately, a view into this important zone is available to the operator through the tuyere peep sight. Here he sees relatively dark pieces of coke "dancing" in the blast. What he sees is of considerable help in interpreting the behavior of the furnace at a given time but the very rapidly moving particles and the intense radiation obscures what is happening very deep in the zone. This investigation was initiated in the hope that a better understanding of the combustion region could be obtained by using a high speed camera with a maximum speed of 3000 frames per sec. It seemed the best practical method of "slowing down" this characteristically violent action within the highly luminous field. Model studies and tuyere probing also have been used to aid in explaining the observed phenomena. Above the combustion zone, but below the fusion zone, there is probably a region in which the coke is comparatively stationary. Here are zones in which the gases must flow up through the granular bed counter to descending liquid slag and metal. There is no easy way to observe this zone in a blast furnace, but model studies have been of some help in explaining the nature of the zone and the laws governing the flow of the fluids involved. The whole problem is difficult and involved and any approach to a complete solution may require long investigation. This preliminary report has been written, therefore, because it is believed that appreciable progress has already been made that would be of interest to others. Tuyere Studies, Chemistry and Kinetics It is well known from the early work of Kinney and coworkers1,2 that combustion of carbon before the tuyeres appears to occur in two zones: Zone A: C + O, = CO2; AH77°F. = — 14,108 Btu per lb of carbon [I] Zone B: CO2 + C = 2CO; H77°F = + 6,183 Btu per lb of carbon [2] Zone A (Fig. 1) is close to the tip of the tuyere and zone B is somewhat farther back; there being a transition region in which both reactions occur. It is interesting to estimate the rate at which coke is burned before a tuyere with a wind rate of 90,000 cfm in a modern furnace having 18 tuyeres. Approximately 0.55 lb of carbon is consumed by eq 1 per tuyere per sec. A like amount disappears by eq 2 for a total consumption of 1.11 Ib per sec per tuyere. Assuming the coke is 85 pct C and has a bulk density of 30 lb per cu ft, this figure can be converted to a total of 1.30 lb of coke with a bulk volume of 0.043 cu ft disappearing per sec per tuyere. At the temperatures prevailing in the combustion zone (according to Kozlovich,³ he maximum is about 3400°F), the rate at which carbon is con-

Jan 1, 1953

By B. H. Caudle, B. M. Hickman, I. H. Silberberg

Secondary recovery projects often are not started in oil reservoirs until dictated by rising GOR&apos;s or declining oil production. Such circumstances require a well dispersed injection pattern to prevent the oil bank from bypassing the production wells. Many times this purpose is served by using the five-spot or line-drive patterns, in which half of the wells are made injection wells. A regular injection pattern is proposed that is based on the same well spacing as the five-spot but in which only a third of the wells need be converted to injection wells. Fluid flow model studies on this proposed pattern show that production histories will be as good as those for a five-spot pattern at mobility ratios of three and above. The model data are presented in a form that may be used to predict recoveries from both homogeneous and stratified formations. Introduction The injection of fluid into a petroleum reservoir usually is prompted by an actual, or predicted, loss in the productivity of the reservoir. Often, an oil reservoir is produced by pressure depletion until high GOR&apos;s dictate a change in policy. Fluid injection also causes increased ultimate recovery, but this usually is of less importance to the operator than is the maintenance of the production rate. It is a fact that the ultimate recovery in any particular fluid injection project is relatively independent of the number and spacing of the injection wells as long as the reservoir voidage through the production wells is balanced by the total injection rate. However, the response of a production well is directly affected by the distance it lies from an injection well. In places where the well productivities are declining, the injection wells should be spaced as evenly as possible among the producing wells ("dispersed" injection pattern). More particularly, if the production response depends upon the formation (and subsequent production) of an oil bank, each production well should be surrounded by injection wells. Otherwise, the oil productivity will increase very little as the oil bank moves past the well.&apos;.&apos; An evenly spaced injection pattern has the best chance of generating an oil kick in the production wells. If reservoir voidage and injection rates are to be equal, the ratio of injection wells to production wells must be equal to the ratio of the average injectivity to the average productivity (in reservoir volumes). This ratio is in strumental in choosing the injection pattern. Table 1 shows the production well to injection well ratio for the dispersed injection patterns that have been described in the literature.&apos;-&apos; All of these patterns will have comparable recoveries and response times (for the same basic distance between wells). The choice of pattern there fore depends upon the relative injectivity and productivity of the wells and upon the type of drilling pattern employed. Another important factor may be the ability of the proposed production wells to make up the lost productivity from those wells converted to injectors. These factors become more pronounced at the higher oil viscosities (low gravity oils). All other things being equal, the probable ratio of single well injectivity to single well productivity will be equal to the water-oil mobility ratio of the proposed flood. Thus, high mobility ratios (due to low gravity oil) should call for fewer injection wells — as long as these injection wells are "dispersed" to obtain more even pro duction response for the remaining wells. Secondary re covery projects in oil reservoirs seldom, if ever, will have mobility ratios requiring more injection wells than production wells. Thus, only the last five of the patterns listed in Table 1 will be of significant interest in oil recovery. Almost every development drilling program calls for the wells to be drilled along equally spaced rows and

Jan 1, 1969

By J. A. Stachura

Continuous mining machinery provides the coal industry with one way to compete for a larger share of the total energy market. Various types of machines are discussed and some of the problems with continuous miners, encountered by operators, are reviewed. Equipment manufacturers are working with mine personnel to provide solutions for problems that arise. While coal production over the past 25 or 30 years has been on a horizontal plane, coal&apos;s share of the total energy market has declined. To participate more effectively in this total energy market, it is necessary to produce coal more efficiently. It is the obligation of all management, employes, and mining departments to gear the deep mining industry to the rapid progress and changing of today&apos;s modern industry. This can be accomplished in the near future with the selection of the proper type of continuous miner best suited to each operator&apos;s individual situation. In most mining operations there is tremendous incentive to undertake the continuous mining program. It can reduce the size of the mine greatly by permitting a minimum of working places; it makes pillar recovery work more efficient from the standpoint of overall cost, amount of coal recovered, and safety. The work force can be reduced materially permitting closer and more efficient supervision. It simplifies maintenance because equipment can be more readily standardized. The trend of the coal market favors the use of continuous mining machines. Although there appears to be a general feeling that continuous mining is still a relatively new program and will be slow in replacing conventional mechanical equipment, the fact is that tremendous strides have been made since the first machines were installed in 1948. This program is advancing at approximately the same rate that mobile loading machines replaced hand loading. From 1948 to 1955 there were approximately 450 continuous mining machines in service. In October 1959, a survey revealed that there were more than 700 continuous mining machines in service. Many operators have expressed a desire to undertake this program, but they feel that they could not do so at this time because of one or more of the following reasons: 1) the thickness of their coal seams, 2) seam characteristics, 3) soft bottoms, 4) bad roof conditions, 5) size consist, 6) insufficient flexibility in machines, 7) difficult ventilation problems, and 8) high maintenance costs. With the realization on coal about the same today as it was in 1948, or slightly less and since coal is still failing to participate to a greater degree in the total energy market, it is not surprising that the coal industry is desperately exploring more economical methods for deep mining. The manufacturers are aware that the coal industry is willing to invest in continuous miners if the equipment is built for maximum flexibility, will produce higher tons per man, and assure long life between overhaul programs. CONTINUOUS MINING MACHINES Before discussing details regarding the selection of a continuous miner, let us have a preview of some of the continuous mining machines which are available to the coal industry today. Jeffrey Manufacturing Co.: The machine shown is the Jeffrey 76 A.M. Colmol. This is their most widely used miner, and has been particularly successful in central Pennsylvania and in high-wall mining in western Kentucky. One of the outstanding features of this auger-type miner is its portability. The entire mining range can be changed from its lowest point to the maximum height without stopping the mining operation. Jeffrey 76 B.M. Colmol: This machine is similar to the 76 A.M. model; however, it is built bigger and stronger for a mining range of 50 1/2 to 72 in. This is the model that is now available (Fig. 2). Jeffrey has added two arms to the top row, omitted the odd arm in the bottom row, thus permitting a 50 pct larger throat opening. This eliminates one

Jan 1, 1961

By Margaret N. Maxey

Man&apos;s capacity far fretting is endless, and no matter what difficulties we surmount, how many ideals we realize, there is a stealthy pleasure in rejecting mankind or the universe as unworthy of our approval. - Will Durant Until recently, reasons for favoring one or another energy alternative were advanced on the basis of technical considerations and economic realities. However, it is an indication of the cultural climate of our society and growing realization of why energy is our master resource that many citizens have begun to express concern about the social and ethical implications of our energy deci¬sion-making. A vivid indication of this shift toward ethical concerns is reflected in the attention being focused on conservation - even to the point of regarding it as a virtual panacea equivalent to a "free energy resource." Among others, the authors of a publication by Resources for the Future cautions us about the difficulties of defining conservation. They also point out that unrealistic expectations for achieving the high levels of conservation claimed by true believers may boomerang if, at the same time, we are morally required to maintain economic growth and robust productivity for the basic well-being of more people. In its economic meaning, conservation signifies the most economic or cost-effective applications of energy, together with other resources, in a given process or activity. To achieve conservation that is cost-effective, saving energy alone is not sufficient; the cost involved in saving the energy must be no greater than the cost of the energy that is saved. Using its thermodynamic meaning, conservation and efficiency are viewed as constrained by physical laws and measured against ideal limits set by these laws and processes. Since achieving higher levels of technical performance is not without costs, the economic meaning of conservation must be factored into technical possibilities. It is the ethical, equity and environmental meaning of conservation that concerns us here. In its third meaning, conservation consists in moderation as a value which appears inherently worthwhile both in itself and in relation to social choices dedicated to achieving distributive justice. The value of moderation seems predicated on the assumption that natural resources and the environment have fixed, finite, exhaustible capacities for satisfying human needs. Hence norms for moderating human behavior appear to require prescriptions by some authority. Such norms presuppose some agreement on "essential" uses of energy. However, the difficulties of setting behavioral norms loom large, because "... it is as difficult to determine essential energy consumption as to determine what is essential in any other phase of consumption, whether it involves food, clothing, shelter, or recreation." The ethical meaning of conversation is further complicated by a centuries-old argument over the proper exercise of stewardship - i.e., how best to develop natural resources. On the one hand, the preservationist position insists on an inviolate, "hands-off" policy and stands opposed to ongoing development of wilderness areas and mineral resources. On the other hand, the "scientific conservationist" who preaches the "gospel of efficiency" insists on development of resources based on principles of sustained-yield, multiple use and - in the case of competing claims - reserving resources or land for their "higher use." Current confusion reigns among opinion leaders in the environmental movement because they appear to have lost the genius of the original Conservation ethic, developed in the 19th century. They seem to think that conservation is preservation. The question I wish to explore is whether a single-minded, exclusive pursuit of "conservation" in its economic, thermodynamic and preservationist meanings may actually do more harm than good in serving the ethical goals of conservation. There

Jan 1, 1986

By Gary Beerkirkcher

INTRODUCTION The mine hoisting equipment that is selected and installed at a mine is for the lifetime of the mine and, therefore, it is extremely important that a proper choice be made. Several types of mine hoist designs, including double drum hoists, single drum hoists, friction hoists, and various special designs of these, are available to¬day. Each has advantages and disadvantages and they should only be used in suitable applications. Drive systems for mine hoists must be evaluated together with the mechanical systems for each hoist application. It does not make sense to properly select the hoist mechanical system and then choose a drive system that turns out to be a bottleneck. MINE HOIST TYPES There are two basic types of mine hoists available in the world today: the drum hoist, on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe) hoist, which merely passes the rope over the wheel during the hoisting process. Drum Hoists Single Drum Hoist: A single drum hoist (shown diagrammatically in Fig. 1) can be used as a service or production hoist with the cage or skip in balance with a counterweight (Figs. 2 and 3). It can efficiently service one or more levels, since the location of the counterweight at any time is not important. As a pro¬duction hoist with skips in balance, the single drum hoist is best used for single level hoisting. All rope adjustments for proper spotting must be done manually for the single drum hoist. This has to be done periodi¬cally to compensate for rope stretch. A variation of the single drum hoist is the divided drum hoist. If multilayer winding is necessary, the single drum hoist must have a divider to allow a sep¬arate compartment for each rope. If a counterweight is used with a divided drum application, the counter¬ weight rope can be wound on a smaller diameter (Fig. 4). Consequently, it moves a lesser distance than the main conveyance and rope adjustment problems are re¬duced. Double Drum Hoist: A double drum hoist in oper¬ation is shown in Fig. 5. Double Drum Hoist With One Drum Clutched: As a service hoist with cage and counterweight, a double drum hoist with one drum clutched (Fig. 6) can serve several levels efficiently. The advantage of having the clutched drum is that it allows rapid adjustment of ropes due to initial stretch. Some users may prefer the single drum hoist with manual rope adjustment, while others consider the added expense of the second drum and clutch is justified to make rope adjustments quickly. The value of this feature for a particular application should be discussed with the hoist manufacturer. As a production hoist with skips in balance for a multi¬level operation, the clutch can be adjusted for efficient hoisting from any level. Double Drum Hoists with Both Drums Clutched: There are also double drum hoists that have both drums clutched (Fig. 7). The main advantage claimed for this type of hoist is that if something happens in one of the two compartments, the hoist can operate in the other compartment to raise and lower men and sup¬plies. This feature is particularly favorable if there is only one shaft entrance to the mine. Multiple Drum Hoist: The multiple drum hoist, a South African innovation, is a type of drum hoist about which everyone should be aware. Basically, it uses two hoist ropes per conveyance which at great depths per¬mits use of smaller ropes and smaller drums. There are none in use in the United States today. However, they should be considered in very deep mines. Friction (Koepe) Hoists This hoist (Fig. 8) was introduced to the mining world by Frederick Koepe in 1877. The basic prin¬ciple of the friction hoist is that the hoist rope passing

Jan 1, 1982