Search Documents

By Littlewood E

We offer these notes as a practical contribution. All the arguments we advance have been tested by practical experience.In its preparation we realised that our subject was one of such importance and covered so wide a field that, dealt with by one of us alone, it might easily have been too much for him, so we have endeavoured, by mutual criticism and advice and a pooling of ideas, to bring forward a few points that may be of advantage to members. If any of the paper is of benefit to mining on the "Golden Mile," or elsewhere, we shall feel amply repaid for our efforts.It is obvious to all that the longer the machine is working productively per shift the greater the return, to all concerned; the machine-man himself and the company. Furthermore, if a man commences a shift with a definite objective in view; for instance, to bore and fire a specific cut, which he recognizes will give him a good financial return, then that man will exercise all his capabilities to attain that objective.In this paper we hope to demonstrate the value to the machine-man of the knowledge of the capabilities of each hole he bores, so that he will be enabled to utilize his drilling time to the greatest advantage. Also, we hope to show that such drilling time can be advantageously extended.After the war, with the influx of new men to the industry, some education on the finer points of machine work may be desirable, and any instruction in this branch must stress the realization of the value of each hole.We realise that most of those present have a sound workable knowledge of machine-mining, and we are not trying to teach anyone the fundamentals of machine work, but we would like to bring to their attentIon some of the finer points which we believe are very important.The machine-man has control of gear of a capital value of over £150, and the use or misuse of that material has a direct bearing on working costs. Therefore it is imperative that the capital outlay is gainfully employed.A "bogger" in charge of a 5/- shovel engaged unproductively is bad enough. How much worse for £150 worth of gear to be not fully productive.Figs. 1 and 2 demonstrate angles of break, and the full realization of the importance of this angle is essential to our paper. Although these Sketches are two-dimensional, we hope they will be sufficient to demonstrate our meaning. We will pass over them as briefly as possible.Fig. 1 shows three holes asked to perform an identical task.(a) 7-ft. hole bored 2 ft. into solid ground-will not come out.(b) 4-ft. hole bored 1 ft. from solid ground-will come out easily.(c) 5-ft. hole bored to solid ground-the best that can be expected under general conditions encountered.The angle of break is a right-angle, normal to direction of hole.

Jan 1, 1944

By Walter Bonsack

THE CHAIRMAN.-This is the third and last session of the Institute of Metals Division's Symposium on Secondary Metals, and certainly the best of those that I have attended in the last few years. I would say that the increase in interest in secondary metals is quite noticeable by the steadily increasing attendance at these meetings. We have heard about the necessity of utilizing salvaged materials, but we still speak about them as low-grade, or down-graded materials. We still have the wrong perspective. We must willingly admit that these materials are valuable; we cannot go on using the choicest primary metals as morsels for our economic diet in a war of such unbelievable dimensions. This brings up the question-why are we so selective. The answer certainly is not that we know nothing else will do, but rather that we do not know what else will do. To be honest, we should admit our lack of knowledge concerning our complex alloys. Compared to the organic chemists, we metallurgists are very conservative, and the sooner we realize this and start to overcome it the better, because if we do not eliminate this difference, many customers of the metals business will go over to the plastics. If we take for example the development of aluminum alloys, you will see what I mean. From the binary aluminum alloys of 1920, we have progressed to ternary and quarternary alloys in the 1930's. We are only now beginning to use more complex alloys as we are forced to learn more about the effect of various elements on existing alloys. The effects of these elements should be studied now. They can be studied by two methods of approach. The usual method is to start from the base alloy and add various elements one by one in increasing amounts and study the resultant changes in properties. This is a tedious, long way. The other method which the smelters frequently use is to take the off-grade heats and study their characteristics. While the producer of primary alloys often has difficulties in alloying certain elements with the alloy under investigation, the smelter often finds them well alloyed in his raw materials and has no difficulties at all. Elements such as lead are difficult to alloy with aluminum and they tend to segregate severely. However, the amount which will remain alloyed in the metal is usually found in some "secondary" aluminum alloys. If one considers such concentration as the saturation, then by dilution with the same type of alloy, but free of such element, one can produce numerous intermediary alloys for investigation. In this fashion one is fairly certain to get uniformly spaced concentrations of the element under investigation. Similar cases probably exist with other metals. Nevertheless, the amount of work necessary to study all possible combinations is still tremendous. Necessity forces us now to utilize alloys which contain more elements than we are accustomed to. It is, therefore, necessary to study carefully the more complicated alloys. In secondary aluminum we are working and using the alloys which contain as many as 6 to 10 elements and we have learned over a period of several decades to balance

Jan 1, 1943

By Robert M. Dreyer

Although lateritic ore deposits are relatively flat-lying, surficial ore bodies, the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist. Laterite is a soil formed under tropical conditions resulting in the concentration, within the soil zone, of certain trivalent metals - principally iron and aluminum, but also, locally, nickel and manganese. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of partially altered bed rock or saprolite. Whereas bauxite generally is confined to the lateritic zone, some nickel deposits occur in both the laterite and saprolite zones. The evaluation of bauxite and lateritic nickel deposits thus has both similarities and differences. These ores have been formed by supergene, soil-forming solutions moving downward through zones of widely varying permeability within the weathering rock. Because the permeability varies widely, both vertically and laterally. the extent of weathering may vary greatly within short distances. Because the weathering process varies widely, the degree of metal concentration may also vary widely. It is not at all uncommon for a laterite to change, within a few centimeters, from a virtually valueless rock to a high grade ore. Moreover, the depth of weathering, and hence the depth and form of the ore profile, vary greatly. Obviously, for this type of deposit, a few grab samples or a few drill holes are virtually worthless. The evaluation of such a deposit requires a sophisticated statistical study based on thousands of carefully selected samples. As a rule of thumb, the cost of evaluating a large bauxite or lateritic nickel deposit will be about one cent per ton of ore in the ground. Thus, the cost of evaluating a several hundred million ton deposit may be considerable. The following factors must be considered during the evaluation: Type of Sampling: The best and most reliable samples for the evaluation of lateritic ores are taken along large, vertical channels in hand-dug pits. Where labor costs are high, some form of drilling may be used in place of pitting, but it is always wise to choose a drilling procedure after checking drilling results against a series of pit channel samples. The drilling may not reproduce exactly the results from pit channel samples, but it may be possible to derive a constant correction factor. If the physical character of the laterite varies within the deposit, it may, of course, be necessary to change the type of drilling, the correction factor or both. In some areas, it has been found empirically that augers, chum drills, vacuum drills, rotary drills, or core drills yield satisfactory results. The problem is to find which drilling technique gives results most similar to channel samples through the heterogeneous sequence characterizing the laterite in a given area. In lateritic nickel deposits, the drilling characteristics of the lateritic and saprolitic portions of the deposit are very different. Within the saprolite, the major nickel values are commonly found in weathered zones within less altered boulders - a type of occurrence which makes sampling very difficult.

Jan 1, 1979

By D. W. Gentry

Introduction Until recently, there were many jobs for mineral engineering graduates. Traditionally, minerals-related career paths available to university graduates stem from rather standard offerings in the disciplines of mining, metallurgy, petroleum, geology, geophysical engineering, and mineral economics. Within each discipline, there exists many career opportunities. In fact, until fairly recently, the most difficult decision for most graduates was choosing among all the available alternatives. Unfortunately, this relative state of euphoria changed quickly and dramatically within the minerals sector. Within two or three years, graduates from minerals-related engineering disciplines found it exceedingly difficult - and then almost impossible - to secure employment in the minerals sector upon graduation. At the same time, there were dramatic reductions in production requirements and, ultimately, mine closings. This resulted in massive layoffs and often termination of professional personnel possessing significant and valuable industrial experience. Obviously, this worsened an already bad employment picture for those hoping to begin a career in minerals. Certainly, there is no universal agreement on what the future offers for the US minerals industry or the career opportunities associated with it. However, there are a number of considerations that deserve study by students, faculty, administrators, and industrial personnel before minerals-related career paths are chosen. Where Will the Jobs Be and How Many? Everyone is aware that the minerals industry is very cyclic. It is not surprising then that job opportunities for new graduates also fluctuate. Typically, there is a two-to-four year lag between industry's engineering manpower needs and the academic community's ability to produce this talent. Due to the response lag, there will necessarily be years when supply and demand do not match. Employment Projections It is extremely difficult to anticipate what the key career paths might be within the next few years. Considerable speculation remains with respect to whether activity in the US minerals sector over the short-, intermediate-, and long-term will improve, remain status quo, or further deteriorate. However, some information pertaining to the prospects for career opportunities in mining engineering was offered by Tingley and Ghose (ME, Sept. 1983, p. 1274) from a study performed by Fenvessy and Schwab. Results from this industry-sponsored survey suggest that the US will experience 700 more mining engineers than needed in 1985, 1300 in 1990, and 1800 in the year 2000. These conclusions were based on the assumptions that future graduate levels remain flat and demand increases 3.6% annually. Educators quickly argued that depressed job markets, coupled with university student mobility, would negate the assumption of flat mining graduate levels in the immediate future. Student Mobility Student mobility from one engineering discipline to another is high. This is perhaps best demonstrated by the tremendous growth in programs such as computer engineering and computer science at the expense of enrollments in the more traditional engineering programs. The ability and willingness of students to quickly change engineering disciplines in response to existing and perceived job market demands have created significant student, faculty, and resource dislocations within universities nationwide. This has resulted in problems for university faculty and administrators responsible for effective use of

Jan 2, 1985

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board; the Institute itself has three awards to make annually, as follows: the Robert W.' Hunt Medal and Prize, the J. E. Johnson, Jr. Award, and the James Douglas Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a. gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or Papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of. the subject have preference over those dealing with the theoretical, side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the. award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered. by the iron and Steel Committee. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $30000 donated by Mrs. Margaret Hilles. Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron. and Steel Committee, and a frequent contributor of papers to the Institute's TRANSACTIONS. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control off the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made the following regulations concerning it:

Jan 1, 1925

By B. L. Averba

THE determination of retained austenite by X-ray diffraction uses the following relationship:"" Pa = constant . RVaA (8) [1] where: P is the diffracted power from phase a; R, the calculated intensity factor; A, the absorption correction; 8, the diffraction angle; and Va, the irradiated volume of phase a For a flat sample making a glancing angle + with the incident beam the absorption correction is calculated as: * 1 sin (28 - 4) A .= 1 [2] µ sin, (28 — 4) + sin 4 where µ is the linear absorption coefficient. Beu3 has proposed that the computed absorption correction be combined with the constant and that the experimental observation of the absorption correction used in the original method be eliminated. This procedure is permissible only if: 1—There is no preferred orientation in the sample, and 2—The geometric requirements have been met precisely. If these conditions are not met the validity of the determination is questionable. Unfortunately the necessary conditions must be tested experimentally for each determination, and this is done most easily by observing whether the apparent absorption has the form of Eq. 2. In practice it may be convenient to plot P/R vs the parameter sin (2? — )[sin (28 — +) + sin +] to obtain straight lines for the ap- parent absorption correction. Deviations from straight lines indicate either that the sample has not been positioned correctly or that the relative intensities are incorrect. Geiger counter spectrometer methods also have been used successfully for retained austenite determinations. In the usual spectrometer arrangement the sample makes equal angles with the incident and diffracted beams (8 = ); thus the absorption correction is simply 1/2µ and independent of 8. The retained austenite is then easily calculated from integrated intensity measurements on austenite and martensite lines. If the austenite content is not too low and if excessive fluorescence is not encountered it is possible to use filtered radiation and a recording spectrometer. The integrated intensities are then proportional to the areas of the diffraction peaks. For lower austenite contents the following technique was used: A bent quartz monochromator and a Geiger counter spectrometer are employed. The monochromatic radiation is focused on the front slit, and the counter slit is made broad enough to include the entire line. A series of readings are taken in the vicinity of the diffraction peak. The highest reading includes the diffraction line plus background. The background is obtained from the average of several readings on each side of the peak. The integrated intensity is obtained by subtraction. CrK, and FeKa have been used for such determinations. This technique has been found to be as sensitive and as accurate as the photographic methods. In the spectrometer methods the ratio austenite/ martensite may be obtained from readings on austenite and martensite lines and the application of Eq. 1. It is also possible to use external standards and to obtain the austenite contents from measurements on the austenite lines alone. The small correction for carbides then becomes unnecessary. The best standards are probably samples with known

Jan 1, 1954

By Clement K. Chase, Manuel R. Lastra

Introduction The choice of using a dump or heap leaching process or a fine grinding-agitation leaching process is based on the grade and tonnage of the ore body. Low grade ore and small tonnages are best treated by a low-cost method, such as dump or heap leaching. Permeability, however, is the critical factor in a successful leaching operation, regardless of tonnage or grade. Without permeability in the leach bed, no percolation, no dissolution, no extraction, and no success are possible. Solution delivery to the ore is also essential. Solute-to-mineral contact is a requisite. The solute must be effectively strong and not be depleted in active dissolvers, such as acid, ferric iron, cyanide, and oxygen. It must also be moving across the mineral to be dissolved. No pockets of stagnant solution can be allowed. A third factor is recovery of the now-dissolved metal in the pregnant liquor. All such liquor should be gathered at a reasonable metal concentration to make further pumping and processing worthwhile. Control and recovery of pregnant solutions are probably the most ignored factors of solution mining. This stage in recovery is historically where many operations either fail or become viable. Permeability A permeable heap is normally achieved by taking into account heap building/construction and agglomeration/pelletizing. Even though heap building is critical for good permeability, it will not be discussed here. It has been described in detail by others. Instead, this analysis will concentrate on agglomeration and pelletizing. Differences between agglomeration and pelletizing are emphasized. Agglomeration is referred to when small particles are being attached to larger particles -the ore presents a complete size distribution. On the other hand, pelletizing is a process where all particles are fine (less than 850)µm or 20 mesh), as with mill tailings. The difference is important from two points of view: • Mechanical devices used to achieve the desired attaching action; and • Binder dosages. Mechanical Devices Due to the absence of large particles that fines can become attached to, pelletizing should be done in a centrifugal-action-based device, such as an inclined rotating plate, a rotary drum, or a series of belt-transfer points. In agglomeration, large particles play a part as a natural nucleus for the attaching action of fines. Hence, a tumbling action as strong as for pelletizing is not required. Common methods to accomplish agglomeration include: • Cascade belt system with either all belts moving forward or some of them moving forward and at least one moving backward; • Combination of belt plus inclined vibrating chute; • Large concrete mixer drum; and • Belt discharging directly onto stockpiled ore. The proper agglomeration system will depend basically on the size distribution of the ore and the amount and type of clays present. In all of the agglomerating systems described, the tumbling action takes place at the transfer points either from belt to belt, or from belt to inclined chute ore belt to ore pile. Usually, two or three mixing bars at each transfer point are also included to help the mixing action. Plows to move the ore around on a moving belt are also used.

Jan 11, 1984

By Cecil Desch

THIS annual lecture, under the auspices of the Institute of Metals Division, and which was illus- trated by lantern slides, has been printed in full and a limited number are available for distribution on request. Some excerpts from the lecture are given below: Ever since the simple geometrical relations of crystals were discovered, it has been recognized that their proper-ties are best explained by assuming that their ultimate particles are arranged on a space lattice, and that the char-acteristics of that lattice determine the shape of the crystal and its physical and mechanical properties. Modern ex-amination by means of X-rays has widened that concep-tion and given it greater; definiteness, and the atoms are now regarded as the particles forming the space lattice. The splendid achievements of investigators in this field have made it possible to state, for a large number of sub-stances, the form and dimensions of the lattice. The char-acteristic of a lattice is that a unit of simple geometrical form is repeated at regular intervals in three dimensions so as to fill the entire crystal. It follows that there must be certain planes in which the atoms are more closely packed than in planes drawn at any angle to them, and it is these planes of closest packing which play the greatest part in determining the growth and other properties of the crystal. There are actually two stages in crystallization, what-ever be the medium in which it occurs. The first is the ap-pearance of crystal nuclei; the second the growth of those nuclei to form crystals of appreciable .size. The first is clearly a kinetic phenomenon. In the molten mass, solu-tion, or vapor, the molecules are in a state of rapid motion and frequent collision. When the temperature has fallen so far. that it is possible for a crystal to exist, a few col-liding molecules may fail to rebound, and so become at-tached to one another, the balance between the attracting and repelling forces-between them causing them to arrange themselves on a space lattice, to which other molecules sub-sequently attach themselves. It was once maintained that the X-ray evidence demanded that the molecule should dis-appear in the solid crystal, but this was a wrong inference, and in many crystals, but not in all, the chemical molecule retains its identity in the solid state. In pure metals the atom and the molecule are identical, so that the conditions are unusually simple. How many. nuclei will be formed in a given mass is evi-dently a problem in probability. Experiments to deter-mine the relation between the temperature and the number of nuclei formed in a given time have been made with some success by using viscous organic substances, but metals offer much greater difficulties, and the few determinations which have been published are vitiated by serious errors. However, the examination of sections of ingots of the same composition and cast at 'the same temperature in similar molds will show, that the number of crystals does not vary widely.

Jan 3, 1927

By E. P. McCurdy, W. J. Tait, A. E. Craig

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951

By M. S. Seltzer

In a previous paper1 it was shown that activation energies for steady-state creep in lead sulfide single crystals varied with the concentration of electronic defects. For n-type lead-excess crystals, values for the creep activation energy, Qc, decreased from 2.9 to 2.2 ev as the carrier concentration increased from 1017 to 1017 electrons per cu cm, while Q, increased from 1.6 to 2.3 ev for p-type sulfur-excess crystals as the concentration of holes increased from 6 X 1017 to 1018 per cu cm. It was also shown in Ref. 1 that the Q, values could best be correlated with the sum of the self-diffusion activation energies in PbS, i.e., for a given concentration of electrons or holes Q, = QPb + Qs, where Qpb and QS are the activation energies for diffusion of pb210 and s35 in PbS. This result suggests that creep rates are controlled by at least two atomic defects, one for lead migration and one controlling sulfur transport. It would be most desirable to interpret these creep energies in terms of an atomic defect disorder model for lead sulfide. Studies of creep rates as a function of sulfur pressure2 indicate that the defects controlling creep rates are singly ionized lead and sulfur vacancies, VPb and Vs. This hypothesis can be more firmly established by determination of Q, under conditions of constant atomic defect concentration rather than constant electronic defect concentration as has been previously done. Therefore, several measurements have been made of Q, on crystals whose con- centration of lead vacancies or sulfur vacancies has been fixed by equilibration under appropriate sulfur pressure and temperature. It was indicated in Ref. 2 that high-temperature isotherms are available which show how the concentrations of various atomic point defects in PbS vary with composition over the entire homogeneity range for the compound. Two such isotherms are shown in Fig. 1 for 900" and 1000°K. Utilizing these isotherms the concentration of a given defect, say Vbb, may be held constant over a particular temperature range by adjusting the sulfur pressure as the temperature is changed. Thus the concentration of one defect suspected of controlling creep rates may be held constant while other defect concentrations vary. The apparent activation energy for formation of these defects can be obtained from the isotherms giving their concentration as a function of sulfur pressure. Activation energies for creep obtained under conditions of constant defect concentration can then be compared with defect formation energies and certain possible atomic defects can be eliminated as creep-controlling species. We have performed creep experiments as a function of temperature at a stress of 244 g per sq mm under conditions which fixed the lead vacancy concentration, V', at 1016, 3.2 x 1016, and 3.2 x 1017 cm-3, and one were the sulfur vacancy concentration, Vs, was held at lo17 cm-3. The results are presented in Fig. 2 as creep rate, k, vs reciprocal of absolute temperature, 1/T. Specimens 34, 35, and 36 were deformed under constant lead vacancy concentration while specimen

Jan 1, 1969

By E. E. Roecker, J. F. K. Brown

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By C. E. Sims

In some experimental work conducted several years ago, it was noted that sulphur seemed to have a distinct influence on grain size of carbon steels. 111 order to check this observation, a series of S..A.E. 1040 steels was made with the normal composition held as nearly constant as possible. The steels were made with three sulphur levels, which were 0.012, 0.024 and 0.038 per cent sulphur, respectively. For each of the sulphur levels, steels were made with only silicon deoxidization and with aluminum additions of 0.1015, 0.025, 0.050 and 0.10 per cent. The melting medium was an acid-lined high-frequency induction furnace. These steels were forged and rolled and differentiall!. quenched from temperaturcs in the range of 1500O to 1800°F. After this, the A.S.T.M. grain size was determined and plotted as in Fig. I. It will be noted, first of all, that the aluminum-free steels had filler grain size with higher sulphur when heated to 1500, but that this condition was reversed at 1700°. When aluminum was added to produce fine grain size, the steels in the lowest sulphur level were fine-grained only to 1600°. and then only with an addition of one pound of aluminum per ton. The medium sulphur steels werc fine-grained to 1600' with a wider range of aluminum addition. The steels in the highest sulphur level were fine-grained at 1600° over a still wider range of aluminum additions and fine- grained at 1700° with an addition of one pound per ton. Fig. 2 shows curves of the grain-coarsening temperature for these steels and illustrates how sulphur and aluminum combine to give greater inhibition to grain growth than aluminum alone. Only the highest sulphur steels have a grain-coarsening temperaturc above 1700°.. At 1650°, the low sulphur steel is fine-grained only at its peak, while the highest sulphur steel is fine-grained over a wide range. In these tests, one pound of aluminum per ton gave the best results; this is equivalent to about 1 1/2 lb. per ton for commercial condition. IllcQuaid-Ehn tests made on these steels showed the same trend but to a lesser degree. The tests were repeated on a series of S.A.E:. 1015 steels with sulphur levels of 0.02 and 0.03j per cent. Aluminum additions were made in the range from 0.025 to 0.15 per cent. These steels were forged and rolled, normalized at 2000°F. to put them all in the same starting condition, then reheated to various temperatures from 1600" to 1800" and cooled at rates that would allow ferrite precipitation in the austenitic grain boundaries. The results of these tests arc shown in Fig. 3. It will be noted that. up to the temperature of 1650°, there is very little difference in the grain size obtained from the two levels of sulphur. .At temperatures of 1700° and 1750°, however, the lower sulphur steel was fine-grained only with an aluminum addition of 1 1/2 lb, per ton;

Jan 1, 1945

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal and Prize, The J. E: Johnson, Jr. Award, The Lewisohn Platinum Prize to senior members, and the James Douglas Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to' establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term" iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition. of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be ,designated "The Hunt Medallist." This prize is administered by the Iron and Steel Committee. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers to the Institute's Transactions. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control of the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made 'the following regulations concerning it:

Jan 1, 1925

By I. Fatt

Laboratory relative permeability data on reservoir rock are obtained on samples which are not subjected to overburden pressure during the permeability measurements. These data are then used for calculating the performance characteristics of reservoirs in which the rock is under the pressure of the overburden. Recent observations have shown that the permeability and porosity of reservoir sandstones are decreased by application of overburden pressure. These observations led us to a study of the effect of overburden pressure on the relative permeability characteristics of sandstones. A previous note from this laboratory1 showed that overburden pressure, simulated by applying hydraulic pressure to the outside of a plastic mounted core. caused a reduction in permeability of the core by as much as 50 per cent at 10,000 psig. In a multiphase fluid flow system, the relative permeability at a given saturation will change if the permeability or the effective permeability changes but not if both permeability and effective permeability change by the same ratio. The tests described in this note were made to determine the effect of overburden pressure on permeability and effective gas permeability in the gas-oil system. The gas-oil system was chosen because the available equipment was best suited for studying this system. The resultant data can be applied to other systems of interest because the gas permeability in the gas-oil system is the permeability of the nonwetting phase and, as such, is equivalent to the gas permeability in the gas-oil-water system and to the oil permeability in the oil-water system. EXPERIMENTAL METHOD Cylindrical test plugs, one in. in diameter and one in. long, were cut from sandstone core samples from three different reservoirs. After extraction in toluene, the plugs were mounted in Lucite by conventional core mounting methods.3 The core properties are given in the legend in Fig. 1. The mounted cores were machined to fit the apparatus shown in Fig 4. Air permeabilities as a function of overburden pressure were measured by connecting lines (1) and (2) to a conventional air permeameter. To measure porosity changes as a function of overburden pressure, the lines leading to (1) and (2) and the core were saturated with kerosene; line (1) was capped and a small bore precision calibrated pipet was connected to (2). Changes in pore volume of the core as overburden pressure was applied were noted by reading the amount of kerosene produced into the pipet. To correct for the change in volume of the lines inside the hydraulic cell as a function of pressure, a pressure-vs-volume run was made with a solid Lucite cylinder substituted for the core. The change in volume of the lines was about 10 per cent of the change in pore volume of the core. No correction was needed for the permeability measurements because there was no measurable pressure drop in the lines at the maximum overburden pressure. Relative gas permeabilities were measured by the stationary liquid method described by Osoba, et al.' Gas saturations were obtained by allowing the kerosene from a kerosene saturated core to evaporate out. This procedure was followed

Jan 1, 1953

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as he aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petro-graphic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs. Stereoscopic Photographs Where the subject or subjects to be photographed are small but not of microscopic size, an ordinary camera having a ground-glass focusing screen is set up vertically over the field. The material to be photographed is placed on a card, the surface of which is suitable as a background. The card is mounted so that it can be tilted about 5' above and below the horizontal plane, on an axis that coincides with the north-south diameter of the viewing screen. A simple way of achieving this is to mount the card on an object having a convex lower surface. In our laboratory, a watch-glass has been used, with plasticene as the mounting medium. The convex surface should be mounted on a support having a round opening on top and a flat bottom. A roll of tape, a petri dish, a beaker, or any other piece of equipment having the proper shape to give stability to the setup will be satisfactory. The arrangement of the required equipment is shown in Fig 1. For the best results, the subject to be photographed should be mounted in the plane of the axis of rotation. To achieve this effect, the depth of the mass of plasticene between the background and the watch-glass is varied so that when the watch-glass is tilted back and forth on the axis, the subject to be photographed does not appear to move back and forth across the viewing screen. A permanent piece of equipment, embodying an adjustable vertical screw, with lock-nuts, could be made for this purpose. The subject may be illuminated in any manner desired. It was found that the presence of shadows intensifies the effect of depth. In taking the photographs, the concave surface is mounted so that one side of the background card is about 5' below the horizontal, while the axis remains in the horizontal plane. The subject is focused carefully on the ground glass and a picture is taken. The card is then tilted so that the opposite side is about 5' below the horizontal, while the axis still remains in the horizontal plane. The subject is again put in focus and another picture is taken. After both pictures are developed and printed, they are placed side by side in the same orientation and examined with a stereoscopic viewer. If depressions appear where there ought

Jan 1, 1950

By R. S. Olson

An analysis of the wash thickener-two stage filtration circuit was undertaken to quantitatively describe the circuit performance. On the basis of information developed in this study, the factors of major importance in reducing soluble loss are: filter wash, wash zone size, filter capacity, filter feed pulp dilution, blow back, filter cloth, water to repulp, water to primary wash, water to feed pulp and thickener underflow. The wash thickener-two stage filtration circuit has been used in many hydrometallurgical plants to separate solute from leach solids. As many as 20 to 30 plant operating variables determine the performance of the wash circuit and hence the soluble loss. The complex relationships of these variables, with each other and with soluble loss, make the evaluation of their effect on mill performance difficult. An analysis of this type of circuit was undertaken to quantitatively describe the circuit performance. THE CIRCUIT The diagram in Fig. 1 represents the operation of the wash thickener-two stage filter circuit. This circuit provides for counter current, cross current or for a combination of countercurrent-cross current operation. The feed pulp stream, J, is intended to include any solution or water, other than primary and secondary filtrate, which enters the wash thickener. Except for filter washing, the operations in the circuit are simple mixing operations which can be described by material balance. The concentration of solute in the filtrate and cake solution after application of wash liquor cannot be described by simple material balance. The displacement washing equation, derived by Rhodes1 and extended by Choundhury and Dahlstrom,2 appears to best describe this case of miscible displacement in porous media. In a useful form, it is

Jan 1, 1963

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By John J. Egan, A. B. Kinzel, Walter Crafts

The demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low temperatures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selection of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low temperatures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120' C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939