Search Documents

The underwater explosions have been used for several decades for the determination of energy content of explosives. This test method is the only one by which shock, fly rock and total energy can be measured separately. It enables to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the fly rock energy is very important feature for the blasting explosives. The purpose of this study was to establish a test place for the underwater experiments in an old water filled open pit, to estimate the repeatability of the energy measurements, to calculate the standard deviations and to compare the total energy content of commercial explosives to the theoretical values calculated by the thermo dynamical program. The test method seems to work quite well especially for the homogeneous explosives. The difference between the energy content of theoretically calculated and measured values for the homogeneous emulsion explosives was about -3% and for the dynamite about -5%. The energy difference for the unhomogeneous ANFO was detected to be -19%. The diameter of the charge was 15 cm and it was obviously too small for ANFO to detonate ideally. On the basis of the test results this test method seems to fit best for the cap sensitive, completely homogeneous, spherical charges whose masses are big enough and which are initiated from the centre of the charge. The underwater explosions as a test method is the only one which can separate shock, bubble and total energies from each other and therefore makes it possible to develop the properties of explosives for different purposes which is very important feature of this method.

Jan 1, 2005

By Michael W. Oakland

This paper summarizes the analysis and design of a pile foundation system for two 400 ft. diameter, 500 ft. high cooling tower using a detailed finite element analysis package. The cooling towers are at the Brayton Point Power Plant in Somerset, Massachusetts. The design-build project will convert the power plant to a closed loop cooling system to reduce return of heated water to the bay. Each cooling tower is supported on a 5 ft. thick by 16 ft. wide ring beam with 44 columns oriented in a radial pattern. The allowable lateral movement on the thin wall shell was limited to only 0.5 inches. Lateral and tension resistance were the primary concerns for the large, but lightweight structure and the critical issue was the lateral response of piles and pile groups within the system. By constructing a detailed model of the foundation system including modeling each pile as an independent element, the contribution of each element was separately assessed and the system tuned to take best advantage of the load distribution afforded by the ring beam as well as the soil structure interaction created by tangential as well as radial resistance of the pile groups. The detailed model also incorporated the lateral resistance of interior piles supporting an equipment slab within the ring beam. Simpler models analyzed the pile groups independent of the complete structure and generally only relied on radial stiffness and generally resulted in large groups of piles needed at each pier. Through a series of trial configurations, the number of piles used was optimized. Confirmatory lateral, vertical and tension load tests were conducted and final fine tuning of the model completed.

Jan 1, 2010

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

By Joseph T. Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned. Previous Theories of Origin Descriptions of the deposits and theories of their origin have been concerned mainly with Iron Mountain and Pilot Knob, which represent the two contrasting types of occurrence. The Iron Mountain deposits have been considered of close magmatic origin by Whitney' in 18.54, Geijer2 in 1915, and Spurr3 in 1927. Whitney referred to them as of eruptive origin. Geijer considered them fissure fillings at magmatic temperatures. Spurr called them vein dikes formed from ore magma which was essentially fluid iron oxide. Schmidt4 in 1872 ascribed them to fissure filling by thermal chalybeate waters of meteoric origin. Nason5 in 1892 advanced essentially the same explanation. One of the best

Jan 1, 1929

By B. W. Jong

As part of the Bureau of Mines program to develop substitute or improved performance refractory materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives on sintering and strength properties of aialon (silicon aluminum oxynitride) compositions fabricated by a conventional powder metallurgy technique. Additions of Y203, Gd203, CeO2, MgO, ZrO2, ZrSiO4, and MgA12O4 to a sialon composition containing 70 pct ß-Si3N4 + 30 pct a-A1203 increased sintered densities by as much as 50 pct over densities of undoped material. The studies also indicated that sintered densities reached a maximum between 20 and 30 mole-pct a-A1203 when a series of sialon compositions of a-Si3N4, having 6.7 to 57.9 pet a-Al203, were doped with Y203, Gd2O3, and MgO. In studies to establish the effect of the crystalline phase of the silicon nitride and alumina used, tests were made using a- and ß-Si3N4 and a- and ?-A12 03 as starting materials. The tests indicated that when using an addition of 5 wt-pct Y203, best results were obtained with a sialon composed of 74.4 mole-pct a-Si304 and 25.6 mole-pct ?-A1203. In other tests made with this sialon composition MOR values of 28,120 and 29,500 psi at 25° C, and 23,520 and 16,850 psi at 1,400° C, were obtained when doping with 5 wt-pct ZrSiO4 and ZrO2, respectively.

Jan 1, 1980

By J. M. Gaines, C. H. Herty

IRon oxide (FeO) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating slags Previous Investigations The solubility of oxygen in iron has been determined by a number of investigators (see Table 1) but their effort's have been directed toward the

By Sunder S. Saluja

Man had to learn to break rocks as early as the Stone Age, when they formed his main source of raw material. He started with chipping and over the years has reached a stage where he can employ atomic blasts and break, with one blast, millions of tons of rock. In between these two extremes there have been several stages of development including firesetting, use of the expansion of water on freezing in chipped cracks in cold climates, the use of low or deflagrating explosive black powder in about the 17th century, the use of high explosives with the discovery of nitroglycerine in 1846 by Sobrero, followed by the monumental discoveries of the great Swedish scientist Alfred Nobel in the latter half of the nineteenth century. The attempts to develop a stronger and still stronger explosive force were accompanied by investigations to understand the mechanism of failure of rock so that the force could be used to the best advantage; the latter, of course, have lagged far behind the former. This is mainly due to the fact that the chemical reactions involving high explosives as well as the processes resulting in the breakage of rock take place at too great a rate to be studied with the equipment that has been only recently available. Moreover, the development of stronger explosive forces was prompted by military necessities in the past and competition, at present, among highly developed nations. With the development, however, of the new techniques such as micro- second photography, microsecond flash radiography, extremely high-speed movies, strain gage assemblies, electronic chronographs and other improved electronic techniques, the investigator has in the last decade or

Jan 1, 1968

By Richard E. Chism

SAN DIMAS, in the State of Durango, Mexico, on the frontier of the State of Sinaloa, is the centre of an extensive and rich mining region, which has been exploited for over a hundred years; and the patio process for working silver ores has there attained the highest perfection of which it is capable. Local modifications have been engrafted upon the underlying principles of the process, but, as a whole, the San Dimas practice so fully illustrates its typical capabilities, that I have undertaken to describe its workings in the hope of lightening, to some degree, the labors of my professional brethren who may have occasion to visit Mexico." As is tolerably well known, the patio process, like all other systems of free amalgamation, is not successful with ores containing more than a trace of zinc or lead, the presence of zincblende being especially obnoxious. Iron and copper in small quantities are not particularly disadvantageous. The process succeeds very well with all sulphide ores which do not contain much more than a trace of arsenic and antimony, provided the tailings are concentrated, although, of course, it is best adapted for free milling ores. For suitable silver ores that contain small amounts of free gold the process is still a good one, but where the gold is combined with sulphurets, a considerable and even an excessive loss is inevitable. Hitherto the Mexicans have submitted to this loss, but, since the introduction of American mills, they are gradually abandoning the patio process in favor of the other. The San Dimas ores have a gangue of quartz and feldspar. They are composed principally of silver sulphides, with some chloride and

Jan 1, 1883

In This Chapter [Ventilation: dilution and displacement Water sprays: wetting and airborne capture Water additives: foam and wetting agents Dust collectors: filtration efficiency and inlet capture efficiency Reducing the generation of dust for cutting, drilling, blasting, crushing, and conveying] [This chapter will give you a general perspective on what works or doesn’t work. The chapter will also help if your dust control problem doesn’t fit any of the circumstances described in later chapters. ] This chapter describes the three major control methods used to reduce airborne dust in tunnels and underground mines: ventilation, water, and dust collectors. It also describes methods to reduce the generation of dust, so less has to be removed from the mine air. The ventilation methods provide the best use of air in the vicinity of workers and in the vicinity of dust sources. In this sense, the methods described are local ventilation methods. Most of the emphasis is on so-called displacement ventilation because it is the most effective dust control technique available. The section on water sprays outlines the dual role of sprays—wetting and airborne capture—and describes why wetting is more important. It also corrects some of the misconceptions about spray effectiveness and describes circumstances where sprays can actually increase the dust exposure of workers. The section on dust collectors outlines the circumstances under which dust collectors can be expected to function effectively. It also describes some common design and maintenance problems. The final section describes how to reduce the amount of dust that gets into the air in the first place, since once the dust is airborne it is always harder to control.

Jan 6, 2003

By R. F. Slack, J. C. Draper, J. A. Younkins

In 1959, the Duquesne Light Co. was faced with the problem of moving more than 40 million tons of bituminous coal in Greene County, Pa. The coal had to travel a distance of about 4 ½ miles from a new mine portal in Rocky Run Valley to the company preparation plant and loading facilities on the Monongahela River. After careful study of this immense transport problem, Duquesne decided that the belt conveyor system described in the following pages offered the best solution. This system, now in operation, is probably one of the four or five longest permanent overland conveyor systems in existence. The general layout of the entire system is shown in Fig. I. A detailed description of the salient features of the system is presented below. THE MINE The valley of Rocky Run where the system begins is very, very narrow and very steep. It was chosen as the site of Duquesne's new mine portal because it was the only place on this particular property where the Sewickley coal seam cropped out. The valley also had two other advantages. First, it fronted on a state road and, second, it offered a site where some 4 million gallons of water could be stored for use in dust-allaying sprays needed in the mine. The company elected to construct a drift mine in the valley because this would require neither the hoisting time of a shaft mine nor the walking time of a slope mine. As part of the mine construction project, the valley was leveled by relocating its stream and filling its center with material cut from each side.

Jan 11, 1966

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By D. R. Murray

"A promising long-term solution to uranium tailings reclamation has been the establishment of vegetation directly on the waste material. The soil profiles of areas vegetated for 0, 3, 8 and 10years are characterized as to the extent of soil development . The characteristics are compared with the visually interpreted soil profile. Organic matter content is presently the best analytical judge of soil development. Vegetation procedures have produced a build-up of organic matter in the top 10cm of tailings where natural microbial populations flourish. The CN ratio is high and the profile depth shallow, suggesting the need for additional fertilizer applications.IntroductionThe reduction of surface erosion and improved aesthetics of uranium tailings has been accomplished by the establishment of a vegetative cover. In 1971 research concentrated on developing methods of plant establishment at minimal cost and soil amendments on uranium tailings in Elliot Lake , Ontario. One process of stabilization used on a large scale was direct seeding of grasses and legumes into the tailings which had received only limestone and fertilizer treatments. Fertilizer additions were made for varying lengths of time in subsequent years to maintain the established cover.Maintenance-free vegetation would be possible once a soil profile developed with sufficient nutrient recycle and plant regeneration capabilities(1). Tailings vegetated in 1971, 1973 and 1978 that had received either 3 or 5 years of maintenance fertilizers were examined for soil development profiles. The extent of soil development and the relative effect of time and fertilizer would provide direction on reaching the goal of a self-sustaining cover.This paper is an abridgment of Division Report MRP /MRL 81-126 of the same title(2)."

Jan 1, 1984

By Cameron A

In recent years there have been significant developments in the tech- nology available for blast monitoring, analysis and simulation. Progress in these areas has been achieved through research conducted by explo- sives manufacturers and independent research groups from universities and mining companies. Miners are increasingly keen to exploit this tech- nology to help them design blasts which make optimum use of explo- sives to produce easily excavated muckpiles for the minimum possible cost. The art of blast design in the future will increasingly depend on an adequate understanding of the nature of the rock mass, the perfor- mance of explosives and the characteristics required of the muckpile to suit the chosen excavation machinery. Despite recent advances in blast simulation and the prediction of blasting performance, the best way to determine how a particular explosive will function relative to other explosives is to conduct properly designed and monitored field trials. This paper discusses recent work at Mount Thorley Colliery which demonstrates that field blasting trials can be monitored and analysed to provide quantitative data on the relative performance of bulk explosives. Techniques used in the trials included the sampling and analysis of explo- sives, insitu measurement of VOD, monitoring of near and far field vibra- tions, high speed and still photography and survey measurement of muckpiles. These techniques provided data for the analysis of throw, swell, fragmentation and burden movement together with data on the consistency and robustness of different explosive products. The blasting trials allowed both the shock and heave energy of various explosives to be observed in the field and led to the derivation of design rules for the use of differ- ent explosives at the mine.

Jan 1, 1988

L. D. Ricketts, New York, N. Y.-In recent years the metallurgical field of the copper industry has expanded greatly, the copper ores have become lean and diverse in character, and we are obliged to treat such ores on a very large scale. On the commercial side, the operating and consulting staffs of ,the great mining companies have been enlarged and organized, and no great capital expenditure is decided upon until it has been investigated and recommended by a highly organized force of specialists as a committee. I believe that in the scientific field and in the most valuable proceedings of our various societies the old idea of one-man point of view and one-man treatment of principle and detail together has been. splendidly developed and should continue, but for the advancement of our art we should deliberately discuss subjects among ourselves in order to do away with the idiosyncrasies of the individual and to gain a composite view representing the best thought of many men. In the development of new ideas leading to the introduction of new methods, the societies could enlarge their present great field of usefulness if such discussion be had, and in my opinion further great good could be done if a number of men of different qualifications and experience would join in preparing a joint book, each dealing with his particular problem, but consulting the other men. In this way individualism would be preserved and various processes would be described, and if properly reviewed the paper would be palpably capable of analysis, and the student would have at his command the associated efforts of a group of qualified engineers.

Jan 4, 1915

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

By H. D. Hoskold

It was not for the purpose of asserting any superior knowledge or authority, but simply of clearing up, in greater detail, some points casually mentioned in Mr. Scott's able paper, that the writer entered, some two years ago, into the discussion which that paper initiated. In such matters there is always room for differences of judgment, as well as for additional data, which may modify or complete the conclusions even of the best authorities. Those who are immersed in the duties of practical administration or work in the field, and who, being remote from the great scientific national libraries, are obliged to rely on their private collections, and to supplement them by their recollections of earlier studies, labor under special disadvantages in such a discussion; and it must be to the scientific and engineering world a matter for gratitude that Mr. Lyman has been willing to give the benefit of his advantages in this respect. Mr. Lyman would, however, doubtless at once disclaim the conclusion that his masterly summary constitutes " the last word " on this subject, and welcome further evidence, comment and criticism, such as the various contributors may continue to offer. This, therefore, is the motive, and must be the excuse, of the introduction by the writer of the following observations. The Miners' Dial.—Many years since, the writer employed a miners' dial, older in type than Fig. 12,* but without any attached spirit-level, made by Thomas Jones, a pupil of the great Ramsden. Jones was one of the old London makers and opticians, and enjoyed great reputation for accuracy in the con-

Jan 1, 1902

By J. H. Archibald

"This paper describes the use of vector analysis for determining the intersection of mineral deposit veins. The mathematical evolution of the analysis is outlined.IntroductionMany mineral deposits can be characterized by sets of intersecting veins. Often a vein will have a steep dip and may intersect with another similar vein. Finding the intersections of these veins is usually done by graphical means. Structural geologists, by the methods of descriptive geometry, can usual ly predict where intersections of veins will occur. This method normally requires accurate drafting and layout of the problem and does not always lend itself to solution in the field.Another method for solving this problem involves the use of vector analysis, which is easily adapted to hand-held programmable calculators. It is assumed at the outset that the reader is familiar with the dot and cross products used in vector analysis. Two excellent references are cited at the end of this note for convenience.A plane, in general, is defined by three points. The points of interest here are the points where three vertical drillholes penetrate the vein, or plane, in question. The elevations of these three points are best referred to sea level. This requires knowing the elevation of the collar of the drillhole above sea level and the drillhole depth from the collar to the vein. The elevation of the intersection point is then found by subtracting the hole depth from the collar elevation. These three points now define the plane of the vein. A similar set of three points will define a second vein, and it is our object to show analytically their intersection if it exists."

Jan 1, 1983

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

No phase of the steel industry is more typical of its remark- able progress than is the evolution and development of the modern American blast furnace. The founding of the Institute in 1871 also marked the beginning of a new era in the pig-iron industry. The rapidly expanding westward development of the country, with its seemingly unlimited markets, gave rise to unprecedented demands for blast-furnace products. The manner in which the iron industry responded provides a fascinating chapter in the history of industrial development. Prior to this period, the iron industry of the United States, largely concentrated in the East, was based upon the consumption of local iron ores and local fuels, the latter predominately charcoal and anthracite. Small, isolated furnaces were located near scattered ore and fuel sources, and the completely integrated ironworks and steelworks were yet to be developed. In about 1860 exploitation of the newly discovered rich ore deposits in Michigan and the successful adaptation of blast furnaces to coke produced from coal of the great Pittsburgh seam in western Pennsylvania proved to be major factors in firmly establishing the general westward shift of the industry. But these were largely economic in character, and it was not until about 1870 that the aggressive, individualistic nature of the ironmaster asserted itself in no uncertain manner. No longer limited by relatively inadequate equipment and inferior raw materials, and spurred as well as encouraged by those who supplied capital for these new enterprises, furnacemen began to establish unheard of records in iron production. It is not surprising that Pittsburgh was the center of this new activity. Its tenor is best indicated by the following account :l

Jan 1, 1948

By Bradley Stoughton

[Secretary's Note.—TO avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.—J. S. 1 Introduction. This paper gives the results: first,, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castr ings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows : 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such 'as, for example, the wear of railroad-rails, of steel and chilled-iron rolls, car-wheels, etc. 2. These improvemerits seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example: A series of tests on cast-iron

Jan 1, 1913