Search Documents

By C. P. Bowie, George L. Gates

"INTRODUCTION Experience in drilling oil and gas wells has shown that the voidance of blow-outs, twist-offs, fishing jobs, loss of circulation, and heaving and caving of shale formations into the drill hole depends largely on how well the drilling-mud fluid serves its purpose. A possible method for the control of the drilling fluids may be seen from a study of the relation between the particle-size distribution and some of the important drilling-fluid properties, such as the ability to build quickly a relatively impervious mud sheath on the wall of the hole in the porous formations penetrated by the bit during drilling operations. In a wartime economy, which urgently requires conservation of steel, proper functioning of the drilling fluid is particularly important because, as Parks 4/ has stated, intelligent use of good drilling fluids makes possible drilling of wells for thousands of feet in open holes without the necessity of setting protective strings of casing to control the movement of salt water, gas, and troublesome formations into the borehole; consequently, especially in deep wells, of proper drilling fluids materially reduces the need for casing and lowers the cost of drilling and completing the wells."

May 1, 1942

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By A. M. Kiwior

In 1969, the Congress of the United States declared that "the first priority and concern of all in the mining industry must be the health and safety of its most precious resource - the miner," Therefore, Public Law 91-173, Federal Coal Mine Health and Safety Act of 1969, was enacted. Since haulage accidents account for a high percentage of coal mining accidents, Section 314e, ?Hoisting and Mantrips,? was included in the law. This section states: "Each locomotive and haulage car used in an underground coal mine shall be equipped with automatic brakes, when space permits. Where space does not permit automatic brakes, locomotive and haulage cars shall be subject to speed reduction gear, or similar devices approved by the Secretary which are designed to stop the locomotive and haulage cars with the proper margin of safety."

Jan 1, 1975

By E. D. Gardner

The American petroleum industry is supplying the present domestic demand for liquid fuels. Known reserves of petroleum in the ground, however, are limited, and the .cost per barrel of finding new oil pools is increasing. Any deficiencies of domestic production in the near future doubtlessly could be made up by imports: Dependence upon foreign oil for part of our industrial requirements is not necessarily cause for alarm, but in time of war an adequate, dependable, domestic source of liquid fuels is vital to the defense of the country. As a national defense measure, and to insure a future continuous oil supply for our economic machine, it would appear logical to take steps now to develop methods for producing petroleum substitutes within our own borders. This undoubtedly was in the mind of Congress when it passed the Synthetic Liquid Fuels Act (58 stat.190; 30 U. S. C. Sup. Secs. 321-325), Approved April 5, 1944.The title' of the Law reads: An Act authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes. Congress authorized $30,000,000 for a 5-year program and directed the Bureau of Mines to carry it out. The part of the program pertaining to oil shale is being conducted on Naval Oil-Shale Reserves Nos. 1 and 3 (fig. 1) at Anvil Points, near Rifle, Colo.

Jan 1, 1948

By W. E. Robinson

Samples of raw oil shale and kerogen concentrates were oxidized by alkaline potassium permanganate, air, nitric acid, oxygen, and ozone to obtain information about the chemical structure of organic kerogen in oil shale. In one test, oil shale and oil-shale products were oxidized exhaustively with alkaline potassium permanganate, and the distribution of the organic carbon in the final oxidation products was determined. Comparing results of this oxidation with those obtained from other carbonaceous materials and known compounds gave information about the structure of kerogen. Alkaline potassium permanganate oxidation also was used partly to degrade kerogen into soluble products for characterization purposes. Structures present in these degradation products were indicative of type structures originally present in the kerogen. Nitric acid, oxygen, and ozone were used also for partly degrading kerogen to soluble oxidation products. Carbon-balance oxidation tests using alkaline potassium permanganate showed that Colorado oil-shale kerogen differs from many other carbonaceous materials such as coal and kerogens from other areas. Composition of the degradation products indicated that Colorado oil-shale kerogen is predominantly cycloparaffinic and saturated heterocyclic structures with some long-chain paraffinic and aromatic structures present. The ring systems may be connected through short carbon chains or bridges containing oxygen, nitrogen, and sulfur.

Jan 1, 1963

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

By Glenn A. Hazen

This report presents a stress investigation of four coal pillars located under two depths of cover. Each coal pillar was instrumented with ten load cells designed to measure coal pressure during initial and secondary mining. The problem considered was one of uniform triaxial stress as a large coal pillar was loaded under a thick limestone bed. Special attention was given to pillar design procedure. Unconfined uniaxial compression tests were conducted for coal specimens 7/8 in., 2-1/8 in., 3 in., and 4 in. square with length to square side ratios of 1/2, 1, 1-1/2, and 2. Stress-strain curves were recorded. Six specimens were tested at each size. Results show that a coal pillar is composed of an inner zone which is highly loaded plus a region around its perimeter which has lost its elastic strength. The bearing capacity of a coal pillar consists of elastic and crushed coal response: The failure strengths have been determined and will be useful in coal recovery, mine design, and mine safety.

Jan 1, 1975

By Suresh K. Bhatt

This U.S. Bureau of Mines report reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and under development, were investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, monorail bridge conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine research being conducted by the Bureau. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1991

By Santosh Kumar Ray, DEBASHISH MISHRA, Niroj Kumar Mohalik, SOMU MANDAL, Jai Krishna Pandey, Asfar Mobin Khan

Coal is a low-cost and high-calorific-value fuel. The coal mining industry worldwide has been suffering from severe accidents due to coal dust explosion hazards since its inception. Statistically, it was observed that 12,489 fatalities had occurred in 104 reported mining accidents from coal dust explosions during 1900–2020. There are numerous methods for detection, prevention, and control of coal dust explosions in mines. The underground mining environment is unpredictable and has an array of variables. These undulating factors make it difficult to prevent or control the coal dust explosion hazard. However, coal mining is done aggressively throughout the world, especially in developing countries as coal is a major source of thermal energy used in power plants contributing to about 38% (IEA, (2019), World Energy Outlook, IEA, Paris https:// www. iea. org/ repor ts/ world- energy- outlo ok- 2019.) of world electricity. Worldwide, coal dust explosibility studies are carried out in experimental mines, laboratories, and simulations. The complexity, lack of proper infrastructure, and unavailability of laboratory equipment sometimes make it difficult to study coal dust explosibility. The authors have discussed in detail and proposed that the CFD modelling can be a viable option for studying and evaluating coal dust explosibility.

Jun 29, 2022

By Laurel E. Blackman

The DFI Project Information Management Systems (PIMS) Committee cooperated with the US Army Corps of Engineers (USACE) to develop a specification for PIMS used on USACE projects. Once completed the Committee developed a more generic version of this specification for general use, which is contained in this document. This first edition has simply removed the USACE-related requirements from the document. The committee will continue to work on this specification to enhance the content and also incorporate recent technological development for these systems. It is the Committee's intention that a second edition will be issued in 2022.

Jan 1, 2021

By A. S. Ratnayake, H. C. S. Subasinghe

In this study, we review the role of mechanical activation in the pyrometallurgical, hydrometallurgical, and electrometallurgical processing of titanium feedstock. Mechanical activation has been shown to decrease the activation energy of chemical reactions, thus enhancing process efficiency and product quality by reducing processing time and energy consumption. Pyrometallurgical processing is energy-intensive and time-consuming. Hydrometallurgy is costly, requires high-grade feed material, and generates toxic waste. Waste generation and process complexity are the major drawbacks of electrometallurgy and solvent extraction. Bioleaching via a mechanically activated pyrometallurgical process can be identified as an alternative method, but the lengthy processing time is the major disadvantage. Mechanically activated titanium concentrate can be used in a finely tuned combined metallurgical process to overcome the challenges and drawbacks in these technologies.

Aug 3, 2023

By Lotfollah Nahai

India is one of the fortunate countries that has substantial reserves of many raw materials for producing steel; however, for historical and economic reasons these resources have not been aggressively developed until recently. Production of steel on an industrial scale started in 1912, but annual output was below 1 million tons3 in 1938 and about 1,500,000 tons in 1951. Expansion of the steel industry became one of the objectives of India's economic planning after independence in 1947. The Planning Com¬mission's 1951 report emphasized the importance of steel production, but financial obstacles, emphasis on river valley projects, and priority for increased food production in the First 5-Year Plan (1951-56) did not permit large-scale expansion of steel capacity. The 1956 planned target for crude steel, only 1,650,000 tons, was actually exceeded by production of 1,737,900 tons. In the Second 5-Year Plan (1956-61), however, construction of steel plants received a high priority. Currently three new steel plants, each with an annual capacity of approximately 1 million tons of steel, are nearing completion in Rourkela, Dorgapur, and Bhilai. Simultaneously, the two privately owned steel plants and the small State-owned plant in Mysore have been enlarged and modernized. As a result, India's crude steel capacity will be about 6 million tons in 1961, almost evenly divided between Government-owned and privately owned plants. Actual production in 1960 totaled 3,254,000 tons compared with 2,434,000 tons in 1959. Assuming that the population will be 430 million and that capacity production will be achieved, the 1961 per capita steel output will be only 31 pounds compared with 200 pounds for Japan in 1959. Some Indian experts feel that development of steel-consuming industries merits greater emphasis in the Third 5-Year Plan (1961-66) than expanding existing steel-producing facilities. Nonetheless, the Third 5-Year Plan calls for a 10 million ton annual capacity by 1966 to be achieved by expanding the Government-owned plants in Bhilai, Durgapur, and Mysore, and by establishing a new integrated Government plant in Bokaro, in the State of Bihar.

Jan 1, 1961

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

GENTLEMEN, lt is with much pleasure I meet you tonight at this the second meeting of the Australasian Institute of Mining Engineers, held in Western Australia, and I sincerely thank you for the honour you have conferred upon me in electing me as your President. I greatly appreciate the distinction, and will endeavour to fulfil the duties of the office to the best of my ability, and hope to prove a worthy successor to those gentlemen who have held the position before me. On behalf of the local members of the Institute, I extend a hearty welcome to the members from the other States of the Commonwealth, who have come so far to attend this meeting, and also to the non-members whom we have invited this evening. We are especially pleased to have Mr. Gregory, our Minister of Mines and Railways, and the Government and School of Mines officials with us; and I take this opportunity to thank the Premier, Mr. Gregory, and the Government officials for the assistance given us, and for doing so much to make the visit of our members from the other States so pleasant and instructive. I have also to thank the Mayor and Councillors of Kalgoorlie for the courtesy and hospitality given to our members, which is much appreciated.I assume you want me to follow the time-honoured custom of giving a Presidential address...

Jan 1, 1909

By John D. Ridge

Here are summarized 162 papers, published between 1933 and 1967, that deal with various aspects of ore genesis. Emphasis is placed on additions to, or modifications of, ore-formation theory, no matter what type of deposit is discussed. More space is given to papers on the formation of base-metal sulfides solely because more papers are written on this subject. The final conclusion is reached that a chemically and geologically sound theory for the genesis of ore deposits can be built around the concept of concentration of ore e’ements in a magmatically produced ore fluid and around such surface processes as may act to concentrate economically valuable materials from rocks of any origin exposed at the surface.

Jan 1, 1968

By E. H. Burroughs

This bulletin is the sixth in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, and 216 being compilations for the years 1915, 1916, 1917, 1918, and 1919- 1920, respectively. In this bulletin the same general plan has been followed in arranging the references, but one or two additions have been made in the classification.

Jan 1, 1921

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By Lester J. Crow

This study advances the use of elemental sulfur in structural materials by demonstrating its value in bonding high-strength, well-graded basalt aggregates to form sulfur-basalt concretes. Sulfur is an excellent bonding agent, and the strength of a thermoplastic sulfur-aggregate mixture depends, to a large degree, on the strength and grain-size distribution of the aggregate used. A 3-cubic-foot, electrically powered mixer with heat applied to the barrel was used to mix the sulfur and aggregate. Sulfur content of several mixtures was varied to obtain the best workability with a minimum of sulfur in excess of that necessary to fill the voids. The average grain sizes and grain-size distributions were also varied to determine their effects on strength. Unconfined compression tests of forty-five 6-by l2-inch cylinders yielded average strendths of 3,348 psi to 10,398 psi. The highest strength single cylinder was 10,717 psi. The cylinders were tested from 24 hours to 6 days after pouring; after 24 hours the rise in strength was very slight. From the results obtained it appears that sulfur can be a useful construction material. An evaluation was made of a high-vacuum application for sulfur concrete. Sulfur has a high vapor pressure at elevated temperatures, 50° to 100° C; consequently, significant losses by sublimation can be expected. At lower temperatures the losses are not significant; however, this factor will limit its use at a higher temperature.

Jan 1, 1970

By Zsuzsanna Zborovszky

[Certain chapters of the tentative document entitled, "Test Requirements for instruments & Apparatus to be Considered for MESA Intrinsically Safe Certification" are evaluated and supporting data are presented on certain key issues with the purpose of helping the regulatory agency in improving the above document. The subjects discussed in detail are: hot wire ignition with W and BeCu wires; the most sensitive methane-air :and propane air ratio; the ignition limits for inductive-resistive circuits in 8.3°; methane-air mixtures in the 24-OV, 100 mH-2 [ ]H range, the resistive ignition limit as a special case when L ? 0; the capacitive-resistive ignition limit representing a four ,dimensional problem is analyzed and discussed in general and the variation of the ignition limit using Vo and/or r2 as a parameter are determined experimentally. The ignition limit is also determined for the [r1 ,~ r2] = 0 case ("capacitor alone") and for the most dangerous capacitive resistive circuit combination. The ignition limits are below the limits proposed in the document. A survey of the different factors influencing the ignition is made as to their suitability to provide a constant safety factor. It is shown that a constant safety factor cannot be achieved. The best method for applying a safety factor appears to be the increase of initial pressure or use of other gas mixture. The revision of the safety factor concept and ignition limit curves is recommended.]

Jan 1, 1980

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983