Search Documents

By A J. Weston

Block or panel caving technology is far removed from that of the top slicing and block caving of the late nineteenth or early twentieth centuries. The rapid mechanisation and expansion of these methods in the late twentieth century was as much a result of the change of the technology of the unit operations of development, ground support, drilling and blasting and transport as it was of the advances in geotechnical understanding and practice. The small footprint gravity and scraper block caving mines with boundary weakening, rail transport and shaft hoisting of the early to mid-twentieth century have been replaced by massive high lift panel caves using preconditioning of the ore, large load-haul-dump units, adjacent crushers and conveyors to surface. The technology changes in the unit operations are described and the drivers for these changes examined.CITATION:Weston, A J, 2016. The evolution of block caving technology, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 265–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L. D. Smith

Net Present Value Impact of Discount Rate The Discounted Cash Flow (DCF) method of valuations is universally used and accepted. The main criticism of the method is that it does not recognize the value of projects long life projects. This can be seen in the preceding graph where the present value of cash flows in later years are small for discount rates over about 10%. This graph covers a project that has a 25 year operating life. It is clear from the low height of the NPV bars at 10% and 15% in the last years of the project that an additional 25 years would add almost no value to total project NPV. As an example of this effect, an colleague undertook the evaluation of a pulp and paper project. The plant could be justified, but it was not possible to justify planting the trees as they took too long to grow and so had not appreciable NPV. The plant had to purchase wood to feed the plant.

May 1, 2013

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

By B L. Sainsbury, M F. Lee, A Penney

For most practical rock engineering purposes, stress versus strength conditions around underground openings for which rock masses fail and their various modes of failure, are reasonably well-understood and predictable. Some rock masses and particular rock types fail slowly and relatively quietly. However, others can fail rapidly, violently and maybe with the ejection of significant broken rock. In some countries and in some mines, the latter style of violent fracturing and failure of the rock mass is referred to as ‘strain bursting’. It can be alarming and extremely hazardous to nearby miners and machines. For such situations, the design and installation of appropriate ground support, to provide a safe work place, can be challenging. At any particular mine site, it’s often generally understood which local rock masses (rock types) are prone to strain bursting. Competent and strong siliceous rocks and some massive sulphides are often the main offenders. While some neighbouring, equally-competent and strong rocks might also fail, they do so more quietly and without ejection. To understand this contrast, a better understanding of the fracturing process is required other than simple and standard strength versus stress considerations. Suites of standard intact rock properties from numerous Australian mines have been used to define and help understand different high-stress failure styles for component intact rock; especially those prone to violent fracturing (strain bursting). Simple considerations of micro-fracturing (defects in the intact material), plus the available energy at failure versus the energy consumed during fracturing, distinguishes between over-stressed and competent rock types that fracture violently and those that don’t. CITATION:Lee, M F, Penney, A and Sainsbury, B L, 2018. Proneness of competent over-stressed intact rock to violent fracturing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

By C. Hendricks

This paper is based upon field studies conducted in a western Canadian open pit coal mine. This work has involved the adaptation of microprocessor-based instrumentation to monitor various operating parameters on-board blasthole drills and mining shovels. A review of instrumentation and monitoring methodology will first be presented. Based upon experience from field-based studies, the paper will subsequently focus on the application of monitoring technology within the framework of an integrated Equipment Monitoring System. Such a system will permit the real-time performance evaluation of key equipment involved in surface mille production.

Jan 1, 1991

By Mark I. Copeland

The formation of A1203 dispersoids 0,14 and less in size in dilute iron-aluminum alloys by internal oxidation in wet hydrogen and dispersion strengthening of iron by application of the technique to iron powder were found to be feasible by the Bureau of Mines. In flowing H2-1.5 H20 gas, A1203 dispersoids 0.1w and less in size formed (at 650° to 750° C) in Fe-l and 2 Al sheet material but not in Fe-3 or 4 Al alloys. With higher temperatures and/or higher H2O/H2 volume-ratio gases, A1203 and FeA1204 dispersoids >0.14 in size formed in all the sheet materials- Minus 100-mesh Fe 2 Al powders were internally oxidized under conditions that promoted formation of fine A1203 particles in sheet material, and then the oxidized powders were hydrogen reduced, sintered, extruded, and evaluated. During internal oxidation, fine A1203 dispersoids formed within the powder grains, and coarse FeA1204 particles formed on the powder surfaces and grain boundaries. The FeA1204 content was essentially eliminated during sintering by reacting with the unoxidized aluminum that remained in the center of the larger internally oxidized powders. The tensile strength at 800° C depended upon the aluminum-oxygen weight ratio of these elements in the extrusions and reached a maximum of 17,000 psi. The stress-rupture strengths at 800° C of the better alloys were comparable with those of type 310 stainless steel.

Jan 1, 1972

By Wayne D. Gould

Planning for a project does not start with the announcement of the approval for a project. Planning actually begins when the project is only a prospect and it involves the years of experience of many people because their expertise influences the final decisions. In partial anticipation of the Pinto Valley project, as well as a search for improvement in the Copper Cities operation, two projects were undertaken. The first project was to substitute one 26" cyclone for three 20? cyclones in the single stage grinding circuit. The second project was to replace the Hunt air flotation cells with 300 cubic foot mechanical cells. The 300 cubic foot cells were just being introduced, consequently two types of cells were selected for testing. The results from both projects influenced the decisions on equipment for the Pinto Valley project.

Jan 1, 1975

By D. Harrington

In recent years over 100,000 persons have been killed annually in the United. States by accidents; about one-fifth of these have been workers in some of our industries; about one-third have been killed by motor vehicles; about another third have mot death in home accidents, chiefly falls, burns, scalds, explosions, poisons, asphyxiations, suffocations, cuts, scratches, and so forth; and the rest have been killed in public accidents, excluding those caused by vehicles but including accidents on railroads or electric cars, drowning, and deaths by firearms and. other means. Definite statistics on nonfatal accidents are not readily available, but at least 10,000,000 fairly serious accidents probably occur in the United States annually. The latest industrial-accident statistics are obtainable from 1935 National Safety Council publications, in which annual industrial fatalities are divided about as follows (in round numbers): Agriculture, 4,500; trade and service, 4,500; construction, 3,100; transportation and public utilities, 2,900; manufacturing, 2,600; mining, quarrying, petroleum, etc., 1,900.

Jan 1, 1938

By George T. Motock

In Germany the extraction of lithium and its salts has been handled mainly by units of the two major concerns - Metallgesellschaft A, G. and Deutsche Gold und Silber Scheide Anstalt, both with headquarters in Frankfurt. Zinnwaldite, which belongs to the mica group, is the major source of the lithium-containing raw material in Germany. Lepidolite and amblygonite also are used when available, but they are imported, as there are no major deposits of these two minerals in Germany.

Jan 1, 1946

By R. V. Higgins

This report presents the results of a study of water injection in the HX sub-pool fault block V-B, in the Upper Terminal zone, Wilmington field, California, and is based on data obtained to May 1957. An earlier report3/ describes the results of gas injection in part of the field. The principal purpose of the pilot flood was to determine whether a sand having a permeability of 1,200 millidarcys and containing oil having a viscosity of 17 centipoises could be waterflooded effectively. The results of a preliminary study by engineers of the Long Beach Harbor Department of oil recoveries from areas where encroaching edgewater was active and the results of an independent study by a consultant retained by the Long Beach Harbor Department were favorable to a trial waterflood. After these preliminary studies, a detailed petroleum-engineering exam-ination was made of the technical details. As a result, a peripheral flood was started in June 1953. The peripheral flood was deemed desirable because the producing wells are bottomed a short distance from the edgewater. The HX subpool was selected for the pilot test because it is an isolated section of the Upper Terminal zone and is separated from the adjoining pools by faults on the east and west and by edgewater on the north, south, and west. Several petroleum-engineering methods were applied to evaluate the performance of the waterflood, and all showed that injecting water stimulated oil production.

Jan 1, 1958

By R. M. Becker

As part of the Bureau of Mines program for examining the Nation's iron and titanium resources, magnetic, gravity, and geologic surveys were made to permit an estimate of the extent and magnitude of the Iron Mountain, Colorado, titaniferous magnetite deposit. Gabbro is the dominant rock type of the area. Within the gabbro are lenses of titaniferous magnetite, 5 to 25 feet wide and as much as several hundred feet long. These lenses comprise a zone which has scattered occurrences of magnetite for 2,200 feet. To the west, the gabbro grades into a strip of pyroxenite that in turn borders a large monzonite mass. A wedgelike broadening of the pyroxenite with depth accompanied by little or no increase in the titaniferous magnetite is considered a reasonable interpretation of the field data. The iron deposits appear to be limited and discontinuous.

Jan 1, 1961

By P. O. Sandstrom

"Atlas Copco is introducing a new patented method for full-face boring. This paper presents the basic principles of the boring action and discusses the present experience regarding performance and costs. The Atlas Copco ""Full-facers"" are designed for hard-rock applications, although they are successfully boring in soft ground without major changes. The unique patented boring principle referred to as the 'Undercutting Method' permits these machines to bore, economically, in harder ground than machines based on the 'crushing principle'. This is mainly due to considerably lower cutting-tool costs, as the tungsten carbide tips only are in contact with one-third of the bored volume. The remaining rock is 'undercut' and peels off from a slight back pressure.The undercutting method also permits boring of non-circular headings and Atlas Copco has already manufactured two machines for rectangular drifts. This concept could revolutionize development work in mines employing trackless equipment."

Jan 1, 1971

By Robert W. Geehan

"INTRODUCTION A preliminary examination of the Argentena mine was made in 'January 1945 by an engineer of the Bureau, who recommended investigation by diamond drilling. The Bureau conducted a core-drilling project at the mine from April 30 to August 4, 1946. Claims investigated are in sec. 33, T. 24 S., R. 58 E., Mount Diablo base and meridian, in southern Clark County, Nev., about 2.2 miles west of Goodsprings.The Argentena mine has been an intermittent producer of zinc-lead-silver ore since 1926. During the war years, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting F. Refining Co.'s smelter at Salt Lake City, Utah. The mine has been shut down at intervals because of lack of a market for mixed oxidized zinc-lead ore.The 12 holes drilled by the Bureau totaled 1902 feet. The program was designed to test for faulted portions of the ore bodies know in the mine and to test favorable areas for similar ore bodies. As a result of this program, one faulted segment of the ore body was found, and it was established that no one was present in a second fault block. Similar blocks remain unexplored in the vicinity of the mine. Two holes drilled in favorable areas several hundred feet from the mine failed to discover new ore bodies."

Jul 1, 1947

By P Bergin, J M. Galvin, J Harris, J Li, P Kirsch, M Shi, B Hebblewhite, B Whittaker, R Mitra, D Sprott

Controlling unwanted ground movement is critical in mining as well as many other highly hazardous environments, such as construction and tunnelling. Sharing knowledge about effective hazard management is paramount to improving health and safety and operational outcomes across industries, and some industry sectors have embraced this openness as part of the way that they do business. In 2010, the Australian Coal Association Research Program funded the RISKGATE project to build a body of knowledge for managing a broad range of hazards across mine sites, lease areas and mine infrastructure within a mine-life or product life cycle perspective (eg from exploration through to decommissioning, or design through to operation). The RISKGATE body of knowledge was assembled from Australian coal industry experts through a semi-structured bowtie analysis-based action research workshop cycle. By capturing operational knowledge from industry experts, RISKGATE serves to provide a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper presents an overview of RISKGATE topics within the geological and geotechnical domain (strata underground, ground control open cut, outburst, coal bumps and bursts, tailings dams and inrush) with a summary of individual topic structures, as well as showing the contrasts and inter-relationships between these ground management topics. The online user can access information about the causes, controls and consequences related to a priority unwanted event (ie the point at which control of energy is lost) and use this information as a prompt for the development of risk assessments, incident investigation, audits of practice/plans/procedures and for training and development.The paper concludes with a discussion of how RISKGATE can be adapted to other mining domains (eg coal outside of Australia, hard rock mining worldwide, construction, tunnelling) and the opportunity for application of this body of knowledge and the RISKGATE action research process for knowledge management in other highly hazardous environments.CITATION:Kirsch, P, Hebblewhite, B, Sprott, D, Harris, J, Li, J, Shi, M, Whittaker, B, Galvin, J M, Bergin, P, Mitra R and Williams, D, 2014. RISKGATE – shared coal mining knowledge for managing risks across ground management, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By Gordon Sproule

THE papers presented to the Institute, and published in the BULLETIN, in the past three years, may be classified as follows: Geology, Mining, and Milling 89 or 58.5 per cent Smelting, Refining, and Refractories 17 " 11.2 " Mechanical and Physical Metallurgy 7 " 4.6 " General (Economics, Welfare, etc.) 39 " 25.7 " Total 152 100 These figure~ should be excuse enou.gh for. the present paper. As indicated by the title it is proposed: I.-To review briefly some of the more recent developments of Physical Metallurgy; and 11.-To show how Physical Metallurgy functions as the link between mining and production metallurgy on the one hand, and consumption engineering on the other hand. Io these days of specialization, papers of the kind being considered mostly gravitate to the American Society for Metals, the American Society for Testing Materials, the Institute of Metals, and the Iron and Steel Institute. In proof that there is a place for the newest and most specialized of these societies, the American Society for Metals, it may be said that in the Montreal Chapter there are 200 active members, and in the Ontario Chapter more than 200. Yet the overshadowing glamour of the mining industry proper, and the publicity it receives, result in an almost continuous dearth of students in metallurgical engineering at our universities. There are more jobs than graduates.

Jan 1, 1936

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By R. W. Utley

Over one half billion tons of coal per year is scalped, classified, deslimed, drained and rinsed, dewatered and final sized on rotary, vibrating, shaking or stationary screens. The vibrating screen is the industry work horse and performs the bulk of the screening functions in the coal preparation plant. There are two major types of brute force mechanical vibrating screens used in coal preparation plants: (1) the two-bearing one-shaft inclined screen and (2) the four-bearing two-shaft horizontal screen. Both of these types are familiar to coal producers.

Jan 1, 1966