Search Documents

By Jack Parker

"The original design of mine openings and pillars at White Pine was based upon traditional assumptions; i.e., that the principal load is due to the weight of overburden, and that horizontal stresses are equal to one-. third of the vertical.Beginning January, 1964, borehole deformation measurements confirmed suspicions that the principal stress is horizontal and several times greater than the vertical.Vertical stress appears to be directly related to depth, but lateral stresses vary considerably in direction and magnitude. The direction of major principal stress lies parallel to the bedding and is apparently parallel to tension joints. Lateral stresses appear to originate from an igneous intrusive.Mining induces stresses which add to the primitive stresses, in some areas precipitating failure. In this paper, rock failures are illustrated, methods of measurement and typical results are given, and measures to counter or utilize the lateral stresses are described."

Jan 1, 1966

By R Castedo, P Segarra, I del Castillo, L M. López, J A. Sanchidrián

This work investigates some suggested methods for blast vibration monitoring on a hard surface based on 53 tests on a vibration exciter. Errors in the measurement attributable to coupling have been described as function of frequency by the rock-to-mount (or coupling) transmissibility, ie ratio of the velocity of the vibration sensor mount to the velocity of the rock motion. Transmissibility has been measured from 2 to 200 Hz, at two vibration levels (5 and 20 mm/s), in four seismographs. Attachment methods with an anchor, thermal adhesive and gypsum plaster allow stiff rock-to-mount coupling. They ensure accurate measurements (errors below 0.3 dB) for frequencies commonly found in blasting (below 100 Hz) irrespective of the mount characteristics and the vibration level. Free laid mounts and sandbagged vibration sensors lead generally to a poor, weak coupling. Errors are non-linear errors with the input velocity, ie the operating frequency window narrows as the velocity of the ground increases. Free mounts follow ground motion acceptably well (error up to 0.4 dB) at both vibration levels and frequencies below 15 Hz. At higher frequencies, free mounts lead to the largest distortions with expected errors ranging from 0.8 to 6.6 dB. Sandbagging limits the expected errors below 1.3 dB, but it does not prevent large errors that can be up to 4.5 dB. Both frequency and velocity should be considered together to assess the measurement errors instead of the expected accelerations, as it is currently made.CITATION:Segarra, P, Sanchidrián, J A, Castedo, R, López, L M and del Castillo, I, 2015. Effect of vibration sensor mounting method on the quality of vibration measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 545–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M. Deutsch

A common casualty of modern open pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can really be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period. And grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper all of these problems are addressed by encoding these three fundamental open pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot. INTRODUCTION Open pit mines are large and complicated operations, which require significant initial and ongoing investment. A single mine may employ hundreds or thousands of people and creates substantial benefits for both the surrounding and global communities. Planning an operation of this magnitude requires a lot of effort and cannot be done optimally by hand. Mining engineers today rely on many techniques from operations research to guide decision making, and to maximize the value of the mine. Techniques including linear programming, metaheuristics, and network algorithms are all used to solve different problems throughout mine design and optimization. However, techniques based on Boolean satisfiability, including the optimization extension of maximum satisfiability, have not seen much use in mining despite being used in many other fields including electronics design, scheduling, and artificial intelligence. We claim that maximum satisfiability is a useful and meaningful way of expressing and solving optimization problems in mine planning. However, this technique does not come without challenges; the problem is NP-hard, and modern techniques for solving these problems can struggle with the number of variables and clauses that a typical mining problem requires. Also, some of the constraints that mining must contend with do not fit nicely into the satisfiability paradigm. Despite these challenges, we believe that maximum satisfiability provides a useful framework for considering operational constraints and expressing some problems that other techniques can't easily express. Maximum satisfiability can be solved exactly, yielding the true optimal answer which metaheuristics cannot guarantee. In this paper we show the applicability of maximum satisfiability to mining by specifying three fundamental problems in open pit mine optimization. We show how these fundamental problems can be formulated and how they can be extended within the framework of maximum satisfiability. For the remainder of the paper we first give a brief background on common elements between the three problems and an introduction to satisfiability. Then we tackle the three problems; the Ultimate Pit Problem, the Block Scheduling Problem, and the Grade Control Polygon Problem. In the Ultimate Pit Problem we specifically show how to extend the problem to support a minimum mining width – a coveted result for many mining engineers. We then discuss some of the complexities and shortcomings of this framework and possible research directions.

Jan 1, 2019

By William H. Dresher

A recent report to President Reagan from the Business-Higher Education Forum, entitled, "America's Competitive Challenge: Need for a National Response," (1) observes that in the recent past, ". . . much of that research, which is necessary for major breakthroughs and sustained productivity improvements, was redirected to short-term objectives ... At the same time, American universities, which conduct more than half of the nation's basic research, have suffered from an accumulated under-investment in facilities and equipment amounting to an estimated $1-4 billion." Also contributing to the decline in America's productivity, the report said, are "...weak technology transfers between government and industry and between universities and industry..." This report as well as other recent reports and articles have, reopened a subject which has long been debated but rarely resolved-- the interaction between the academic community and industry in the sponsorship and conduct of research. The subject is unfortunately, too often treated as a controversial issue involving ethics and the profit motive when, in fact, the two branches of society -- industry and academia -- are necessarily part of the same system. I would like to speak to you today on the subject of university-industry interactions and to some extent discuss the role of government in such interactions. Finally, I will make some remarks as to how this subject applies to the mining industry.

Jan 1, 1984

By T. H. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By K. J. Murphy, A. R. Smith, A. P. Odorski

"The need for large quantities of oxygen for use in metallurgical processes was a major driving force in the commercialization of tonnage air separation plants. Oxygen, nitrogen and argon impact the quality, energy efficiency and environmental aspects of metals production. Cryogenic air separation processes have been used to supply most industrial requirements, however, newer technologies are available or under development to meet the needs of today's and tomorrow's metallurgical processes. This paper reviews the technical features and state of development of adsorption, chemical, cryogenic and membrane technologies. The technologies are compared in terms of plant size, oxygen purity and pressure, nitrogen and argon co-production, product use pattern and back-up requirements. Computer control systems are described that optimize operation over varying load patterns and ambient conditions; substantially lowering energy consumption. IntroductionOxygen production totalled 390 billion cubic feet in 1987. Although current production is lower than the peak of 455 billion cubic feet reached in 1979, oxygen remains the fifth leading chemical product manufactured in the u.s. (1) Metals manufacturing and fabrication accounts for sixty percent of the oxygen consumed in the u.s. Oxygen use in the steel industry consists of air enrichment for conversion of iron ore, purification of the iron in basic oxygen or other furnaces, and for cutting and welding the finished steel product. Nonferrous ores are smelted in oxygen enriched atmospheres to reduce energy consumption and increase capture of sulfur compounds to meet environmental requirements. In the future oxygen usage is expected to become even more important in metals production as energy costs increase, environmental standards become more stringent, and as new coal based processes become commercialized. Oxygen usage per ton of metal in the new direct reduction processes can be up to ten times higher than traditional steel making."

Jan 1, 1988

By D Smith, A Ramdhani, J Francke

Ground penetrating radar (GPR), a well-established geophysical technique generally used for shallow civil engineering applications, has, in the last decade, found increasing acceptance as a complementary tool in mineral resource evaluations. As new sites are trialled with the method, a greater understanding is being garnered regarding the most suitable environments for long-range radar. Although successful projects have been conducted worldwide for mineral sands, iron ore and alluvial projects – tropical weathering environments have produced some of the most impressive results. Specifically, tropical nickel laterites have shown to be, with some notable exceptions, ideal GPR environments.Such high-resolution remote sensing has particular relevance to bulk commodities or those which possess significant rheological variation within geological units, and has led to some innovative downstream uses within exploration, project development and the larger mining industry. In this paper, we examine the application of long-range GPR in Indonesian nickel laterite deposits in general, to highlight some of these novel applications with particular reference to resource modelling, mine geology and operational economic implications.CITATION:Francke, J, Smith, D and Ramdhani, A, 2014. Ground penetrating radar to enhance the exploration-to-mining value chain, in Proceedings Ninth International Mining Geology Conference 2014 , pp 175–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By P. E. Churchward

The Bureau of Mines developed a process using amines for recovering tungsten as ammonium paratungstate from alkaline leach liquors without producing synthetic scheelite as an intermediate product. Over 90 pct of the tungsten in low-grade scheelite or ferberite concen-trate was recovered as ammonium paratungstate by (l) autoclave leaching the concentrate with Na2CO3, (2) solvent extraction of the acidified leach liquor with kerosine solutions of either a quaternary amine (Aliquat 336) or a primary amine (Primene JM-T), (3) stripping the tungsten values from the quaternary amine with ammoniacal NH4C1 or from the primary amine with NH4OH, and (4) crystallization of ammonium paratungstate from the strip liquor. Reagent consumption in pounds per pound of W03 recovered was, for the quater¬nary amine, 3 Na2CO3, 3.5 H2SO4 , 2.2 NH4Cl, 1 NH3, and 0.4 glacial acetic acid; for the primary amine, it was 3 Na2CO3, 3.5 H2SO4, .06 NH4Cl, and 0.9 NH3. Both reagents extract molybdenum along with tungsten. Silicate and phosphate are partly extracted and contaminate the product; leach liquors containing these impurities require preliminary purification.

Jan 1, 1966

By John G. McCamis

The Maritimes Carboniferous Basin is the largest intermontane basin in the Appalachian Mountain System, occupying a total area of 57,200 square miles and containing up to 30,000 feet of late Devonian through Permian .sediments. Deposition began with continental elastics in late Devonian and early Mississippian. Marine deposition is represented by a limestone-evaporite sequence of late Mississippian age. Pennsylvanian and Permian continental rocks deposited largely in flood-plain and swamp environments complete the succession. Marine seismic data disclose several varieties of structure, both halokinetic and tectonic in origin. Recent exploratory drilling in the offshore part of the Basin encountered good reservoir rocks in the Riversdale sandstones, which also provided encouraging shows. The most likely source rocks of hydro~ arbons in the Maritimes Basin are shales in the Horton and Riversdale groups. Potential recoverable reserves of the Maritimes Basin are estimated to be 400 million barrels of oil or 7.8 trillion cubic feet of gas, based on the volume-of-sediment method of calculation.

Jan 1, 1973

By Robert W. Geehan

"INTRODUCTION The Bureau of Mines, in cooperation with the Federal Geological Survey, explored the Crowell fluorite mine by core drilling in 1945. Claims investigated are in sec. 14, T. 12 S. R. 47 E., M. D. B. & M., in southern rye County, Nev., about 5 miles east of 'Beatty.The twelve holes drilled by the Bureau totaled 3,661 feet. During 1945 the mine operator drove extensive exploration drifts, in part to verify results of the Bureau's work. The drilling program was designed to test for extensions of ore bodies known in the mine.The Crowell mine has shipped Ore to steel plants on the west coast for the past 20 years. During the war this market called for all the fluorite the mine could produce, but previously there were periods when it was difficult to sell ore or concentrates.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is due to Glenn Allen, district engineer;A. C. Johnson, chief, Reno Division, Mining Branch; S. R Zimmerley, chief, Salt Lake City Division, Metallurgical Branch; W. R. Thurston of the Federal Geological Survey for advice on geological problems; and J. Irving Crowell, Jr., operator of the property, for his cooperation."

Nov 1, 1946

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By D. C. Dahlin

The Bureau of Mines conducted laboratory batch beneficiation tests on samples from four potential platinum resources in southeastern Alaska to concentrate platinum and other precious metals. Thin Investigation was done as part of the mission of the Bureau to insure an adequate supply of minerals to meet the Nation's needs. Petrographic studies and beneficiation methods including gravity concentration, froth flotation, and magnetic separation were used to determine mineral association and to attempt to concentrate the platinum values with a primary mineral value such as chromite, copper sulfide, or magnetite. A high-graded sample from the Salt Chuck copper sulfide deposit yielded the platinum-group metal concentrate; the maximum grade attained was 0.04 oz Pt and 1.5 oz Pd per ton of high-grade copper sulfide concentrate. The other samples yielded low-grade primary mineral concentrates with low platinum-group values, and/or the platinum-group metals did not concentrate with the primary mineral value.

Jan 1, 1981

By L. Vollert

"The application of pneumatically-assisted fluidized bed flotation, specifically the ERIEZ HydroFloatTM technology, has found widespread use in non-sulphide processing (particularly phosphate, potash and coal) for the recovery of coarse particles. In gold processing, centrifugal gravity circuits and flash flotation cells are typically employed for the recovery of coarse and near-size liberated gold which tends to accumulate in recycled grinding streams due to bypass to the classifying cyclone underflow streams owing to the higher specific gravity of these gold particles. Early removal of this gold from the grinding circuits contributes toward the reduction of downstream processing losses as a result of overgrinding and particle shape deformation in the case of flotation processing, longer leach residence times in the case of extractive processing, and surface occlusions in the case of both flotation and extractive processing. Furthermore, recovery to bullion attracts higher payment terms by way of comparison to concentrate sales in the case of copper-gold concentrators. This paper assesses the application of pneumatically assisted fluidized bed flotation for the recovery of coarse liberated gold through the analysis of piloting data generated from the operation of a continuously operated 16 inch ERIEZ HydroFloatTM unit treating a sized coarse grinding circuit stream. The paper presents the stage recovery by size performance of the ERIEZ HydroFloatTM unit together with quantitative gold deportment analysis to demonstrate the efficiency with which gold was recovered during this pilot campaign and then compared to more conventional processing units – centrifugal gravity and conventional flotation.INTRODUCTION Newcrest Mining Limited (NML) has identified that an opportunity exists for improving the recovery of coarse composite particles at its current operations, both as a means for improving overall recovery and as an opportunity for early gangue rejection. As such, Newcrest Mining Limited has taken an interest in the application of pneumatically-assisted, fluidized-bed flotation i.e. ERIEZ HydroFloatTM technology. This interest dates back to 2011 with sighter testwork carried out on their Australian-held ore bodies (Kohmuench et al, 2013). Newcrest continues to assess ERIEZ HydroFloatTM potential for coarse composite recovery and, in the case of the topic of this paper, coarse gold recovery based on examples in the literature which demonstrate the efficiency of this technology in this regard (Carmona Franco et al., (2015); Miller et al., (2016); and Kohmuench et al, 2013)."

Jan 1, 2017

By A. A. Lavrinenko

There are discussed the possibilities of using of flotation tailings of platinum-copper-nickel sulfide ores of the Norilsk region for the preparation of backfill mixture instead of a specially produced rock and binder materials to reduce the cost of stowing operations and impact on the environment. It is shown that due to the presence in the tailings of flotation up to 10% of sulfide sulphur, which reduces the strength of the fill materials, and more than 1 g/t PGM it is necessary the preliminary extraction of the sulfides in the product for further processing that give an opportunity to reduce the losses of valuable components. It is shown that by the flotation of the current tailings it is possible to extract 91% of sulfide sulphur, 60% of palladium and 30% platinum in 17% sulfide concentrate containing 2.1 g/t palladium, and to reduce the sulphur content in the tailings up to 0.7%. Due to the easy oxidation of pyrrhotite, there is recommended fractional delivery of the collector with a total consumption 200 g/t. There are discussed results of the flotation study with an additional collector of PGM (sodium diizobutyditiophosfinate), which one show the possibility to increase extraction of platinum on 45%, as well as extraction of sulphur and palladium. For the flotation of sulfides and PGM from the current tailings there is recommended a combination of collectors for primary flotation and only butyl xanthate using in control operations. The possibility of using sludge fraction of the current tailings as a component for the preparation of the combined cementing materials after exposure of sulfides is analyzed. It is shown that the efficiency of the flotation of sulfides from this fraction can be enhanced using selective flocculants. There are discussed the advantages of implementation of completely hydrophobic butadiene-styrene copolymer in comparison with partially hydrophobic polymers. There is discussed an efficiency of the mechanochemical treatment of old tailings in turbo mill and sulphuric acid to remove oxide films from the surface of pyrrhotite before its flotation. Due to the pretreatment operation there is achieved increasing of sulphur extraction and after the introduction to the flotation circuit three control operations there is produced the fill material with sulphur content 2.5%. Keywords: tailings, copper-nickel ore, pyrrhotite, butyl xanthate, sodium diisobutyl dithiophosphinate, selective flocculation, butadiene-styrene copolymer, mechanochemical treatment

Sep 1, 2012

By J. Mrozowski, R. Kurowski, A. Chmielarz, Z. Szolomicki

PbSO4 is a commonly encountered component of the materials used in lead recycling (e.g. battery paste) and in by-products of metallurgical processes (e.g. residues from zinc hydrometallurgy, dust from copper smelting). Smelting of battery paste results in SO2 emission and in generation of significant amounts of hazardous ‘white slag’. Those adverse phenomena can be eliminated by removal of sulphur from the paste. Lead-bearing by-product materials are of polymetallic character with usually low Pb content, which makes lead recovery technologically difficult and uneconomic. However it can be successfully achieved by extraction of lead sulphate from solid phase with triethylenetetramine (TETA) water solutions. That compound has capability for selective solvation of a whole lead sulphate molecule. Virtually pure lead carbonate can be precipitated by means of saturation of lead-loaded aqueous TETA solution with carbon dioxide, and complete regeneration of the extractant is achieved by fixing of sulphate ion into gypsum through operation of calcium hydroxide suspension. The paper presents results of the lab and pilot scale studies into process of battery paste desulphurisation and recovery of lead from the residue of zinc calcine leaching.

Jan 1, 2014

Breakwater Resources Ltd is a Canadian base metals producer with Cu-Pb-Zn operations in Canada, Honduras, and Chile. Two of its operations contain economical gold levels which are recovered in both gravity and flotation concentrates. The gold payable terms in zinc concentrate are poor when compared to gold concentrates or copper concentrates and various flow sheets have been evaluated by Breakwater staff to maximise gold reporting in higher value products. The Myra Falls mine in British Columbia recovers coarse gold in the grinding circuit, part of which is upgraded and sold as a gravity-gold concentrate with the balance being directed to the copper concentrate. A sampling survey showed that there was potential gravity-recoverable gold in the copper regrind circuit. Installing a gravity concentrator in the copper regrind circuit increased the gold grade and recovery in the higher revenue copper concentrate and reduced the quantity reporting to the less well paid zinc concentrate. The El Toqui Mine in southern Chile has distinct high-and low-gold orebodies which are campaigned separately through the flotation plant. The high gold zone yields both a gravity concentrate and an unusual gold flotation concentrate. The gravity concentrate undergoes intensive cyanidation and electrowinning on-site to produce dore, while the fl otation concentrate is sold to gold producers. The zinc concentrate contains signifi cant gold values. The paper describes efforts over the past few years to improve gold returns at Breakwater's operations and highlights the different approaches dictated by the mineralogy of the gold occurrences at these two operations.

Aug 1, 2010

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952