Search Documents

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By Ralph M. Hunter

UNTIL recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged break-down did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to by-pass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdiness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, therefore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 2946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1948

By E. DeGolyer

The problem of good engineering practice and. of good conservation practice in oil production is that of keeping gas in solution. This can best be done by producing a field as a water-drive field. Some degree of water drive is believed to be present in most fields but in the past most fields have been produced too rapidly to allow water drive to be effective. Ultimate recovery should be So per cent greater for fields produced by water drive over that from gas-expansion fields. Wide spacing will permit fields of low-degree water drive to be produced effectively as water-drive fields. INTRODUCTION NEGLECTING all the complicated scientific and technical argument that leads to the conclusion, the solution of the problem of good production practice, of good engineering practice, and of good conservation practice in oil production is to keep gas in solution. This can best be done by producing fields at a rate low enough to make effective the water drive, which exists, it is generally believed, to a degree great enough to be made effective in more than 80 per cent of the fields of the United States. Oil is being so produced in the Ten Section field of California; the Hobbs field of New Mexico; the Yates, Hastings, Friendswood, Anahuac fields and the main sand of the Conroe pool, in Texas; the Magnolia pool in Arkansas, and doubtless in many other pools. The measures of success in the efforts to achieve the solution of the problem are the maintenance of bottom-hole pressure and the prevention of an increase in gas-oil ratio. Some decline from the original bottom-hole pressure and the production of some gas are essential. A pressure gradient from the reservoir to the well is necessary and at least as much gas must be produced as that in solution in a barrel of oil. Once the optimum pressure and the gas-oil ratio have been established, they should be maintained. How common is water drive in oil and gas pools? General opinion is that some degree of water drive is almost universal. Theoretically, this conclusion appears to be a sound one. According to our present understanding of the processes of sedimentation, we would expect to find all sands or sandstone charged with connate water unless it had been displaced by some other fluid, such as fresh water percolating into the beds at the outcrop, or oil and gas, or gas only, in reservoirs. The fact that the original pressure of the fluid system in most reservoirs is approximately that of the hydrostatic head of water for the corresponding depth indicates that the sands are charged with water, and common experience in drilling into the extensions of the porous zones beyond the reservoir is to find them watercharged. The very fact that oil and gas pools have substantial pressures in their original undisturbed state indicates either that a reservoir is a rigid, closed system, a con-

Jan 1, 1941

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By John T. Galey

An intensified search for gas, because of the shortage in the area, led to the completion of 482 wells in southwestern Pennsylvania during 1944. This number was 27 more than the number in 1943, but 118 of the wells were nonproductive. Shallow Development Oil The initial production of the 25 producers completed was slightly less than was obtained from four wells above last yearJs total. The largest well, 20 bbl., was found in the Big Injun (Miss.) sand in Morris township, Washington County, at a depth of 2085 ft. It is currently producing about 3 bbl. per day. Outside the main producing area, a well drilled in Nicholson township, Fayette County, obtained 15 bbl. per day from 1864 to 1866 ft. in the Gantz (U. Dev.) sand. The Federal subsidy of 75¢ per barrel, effective , 1, 1944, which increased to $3.40 the current pipe-line price in this area, seems to have been insufficient stimulus to materially increase drilling for oil, although more repressuring operations are contemplated. Gas The volume of initial open flow of gas developed is off slightly over 10 million cu. ft. from 36 more wells than were completed a year ago, and the average rock pressure of this new gas is more than 100 lb. less than that obtained a year ago. Apparently the best find of this year was reported in Patton township, Allegheny County, where an initial volume of over 4 million cu. ft, was encountered in the Speechley (U. Dev.) sand at a depth of from 3293 to 3303 ft. The rock pressure there, 1190 lb. per sq. in., is nearly virgin. However, this area is fairly well delimited by dry holes and docs not seem nearly so promising from the standpoint of reserves as the Armbrust area, which was discovered several Years ago. In the patton township locality another fair well with 1303 M cu. ft. open flow and 400 lb. Per 59. in. rock pressure completed in the Hundred-Foot (U. Dev.) sand at a a depth of 2125 feet. Armstrong County, as usual, leads in number of producing wells completed with lowest percentage of failures but ranks only fou th in volume of production developed. Only two wells here had more than one million cubic feet capacity, but the rock pessure was under 200 Ib. Per sq. inch. In Fayette County, where the largest portion of new gas was found, activity appears to be shifting eastward. In Luzerne township, four producers having a total combined initial open flow in excess of 10 million cu, ft, were found in the Big Injun (Miss.) sand. The best well was found also in the same area in the Speechley sand (U. Dev.) at a depth of 3460 ft. This was a 2500-M CU. ft. well in Georges township. Several wells of more than a million cubic feet capacity were found in Jackson, Washington, Wayne and Whitley townships, Greene County. None of these, however, was in a new pool.

Jan 1, 1945

By Charles W. Goodale

In the course of the preparation of my paper on " The Occurrence and Treatment of the Argentiferous Manganese Ores of Tombstone District, Arizona" (Dam., xvii., 767), my attention was called to two patents which have been issued for the use of a diaphragm at the upper end of a Howell furnace, whose importance merits more than a passing reference. Mr. J. K. Pardee invented and first put into use in the Algon quin mill, at Philipsburg, Mon., in 1880, a ('new' and useful im provement in rotary ore-roasting furnaces," which was intended "to increase the capacity, effectiveness and working economies of such furnaces." The following description and accompanying figures are taken from the patent papers, dated December 21st, 1880: Fig. 1 is a side elevation of the feed-end of the Howell rotary furnace, with parts broken away, the better to exhibit my invention. Fig. 2 is an end elevation of the same. Fig. 3 is an end elevation of the same, showing a modification of my invention. In operating a furnace of this kind, of the capacity of one ton of ore an hour, it was found that for the best work the two fire-places (one at each end of the revolv ing cylinder) consumed about ten cords of wood every twenty-four hours, and that about twenty-fonr tons of silver-ore were introduced through the feed-pipe. It was also found that of the amount of ore, fully one-third did not go through the revolv ing cylinder, but went into the dust-chanibers about the feed-end of the furnace or cylinder, and this ore going into the dust-chambers was found not to be sufficiently chloridized for amalgamation, but had to be re-roasted. I then caused to be made, out of boiler-plate iron, a segment of a circle, the height of which was about one third of the diameter of. the cylinder or furnace, the circumference of the circle being smaller than the circumference of the furnace, so that about a half-inch space would be left between the plate and the furnace, when said plate or segment was in position. This segment or plate of iron was then fastened to the bottom of the feed pipe, as shown in the drawings, wherein A represents the revolving cylinder or furnace; B, the fire-place and dust-chambers at the feed-end of said furnace; C, the inclined feed-pipe, and D, the diaphragm, partition, or plate fixed within said furnace, A. With the diaphragm or plate, D, in the position shown, the furnace was run for about a month, and it was found that with the furnace in best working condition only four cords of wood every twenty-four hours were consumed, that no fire was required at the feed-end of the furnace, that not one-twelfth of the ore

Jan 1, 1890

By H. B. Bell, P. C. Lidster

A study has been made of the use of ThO2-Y2O3 solid electrolytes to determine activity of chromium in Fe-Cr and Ni-Cr alloys in the temperature range 1300° to 1700°K. This method has been shown to give results which agree with the best vapor pressure measurements. SEVERAL investigations1"5 have been made of chromium activities in Fe-Cr alloys. Most of these have been made by vapor pressure measurements using knudsen cell techniques while one has been made using gas equilibration with H2/H2O gas mixtures. In the present investigation electromotive force measurements have been made on this system using a thoria yttria solid electrolyte. This system was -chosen to establish the technique of measurement at low oxygen potentials, before extending it to Fe-Ni-Cr alloys. The cell used was Pt Cr • Cr2O3 ilThO2 • Y2O3 llalloy • Cr2O3 IPt Since the oxygen pressure of the chromium-chromic oxide mixture lay in the range 10"19 to 1027 atm in the temperature range investigated, thoria yttria electrolytes were used. It was soon found during the investigation that considerable care was required to prepare satisfactory electrolytes and a study was made to find the best method of preparing pellets of TI1O2-Y2O3 solid solution of as near theoretical density as possible. Various compositions in the range 2 to 15 mole pct Y2O3 were studied but the experimental measurements were made with electrolytes containing 4 to 5 pct Y2O3. The method of preparation finally adopted was to use thorium oxalate and yttria as raw materials. The thorium oxalate was decomposed at 900°C for 6 hr to give a reactive powder. This powder was then mixed with the appropriate amount of yttria and ground in an agate mortar for about 4 hr. The powder was moistened with absolute alcohol as a lubricant and pressed in a metal die at a pressure of 7 tons per sq in. The pellets were then heated at 1100°C for 24 hr followed by 24 hr at 1250°C. After this firing cycle the material was reground and repelleted and again fired at 1100° and 1250°C followed by heating for 7 days at 1600°C. It was found in later experiments that a further firing of 4 hr at 2000°C improved the density further and gave pellets of only 2 pct porosity. After firing, the pellets were polished on emery paper and finally with the 2 µ diamond paste. The polishing was followed by a final firing of 24 hr at 1500°C. Investigation showed that this final treatment minimized reaction between the electrolytes and chromium oxide. It was believed that this was because of a lowering of the surface energy of the electrolyte surface. Two types of investigation were carried out to check that the pellets were satisfactory oxygen ion elec-

Jan 1, 1970

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By Camilo Uribe, Williams Calderón, Gonzalo Montes-Atenas

In industrial hydrometallurgical operations, the leaching process is often implemented via heap or dump leaching operations. During the pile up of these massive amounts particles a porous material is then formed. The manner it is constructed is crucial since it will define the permeability and other parameters determining the flowrate of leaching solution across the material. This study aims to estimate how the unsaturated permeability of the staked porous structure confined in a column-like geometry varies with and without particle size segregation. The piling up will be modeled using the Rocky® software. Different disposals of particle size distributions across the column will be simulated and their effect onto the overall column unsaturated permeability will be estimated. It was found that when the belt speed increased, the particle segregation in the column also increased. This condition is expected to improve the permeability of the porous structure in the column, probably due to the smaller compaction of larger particles when they are located at the base of the column and maintain a suitable porosity to permit leaching flowrates relatively high, suggesting better extraction results. The opposite was observed when small particles were preferentially located at the bottom of the column. These results are expected to provide an insight towards what is the best way to construct heaps and dumps.

Jan 1, 2014

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012

The first prize of the President's Prizes has been awarded to J. J. Beeson for his paper entitled "Disseminated Copper Ores of Bingham, Canyon." When this paper-was written, Mr. Beeson was a student at Stanford University, and was president of the Stanford Geological and Mining Society. The President's prizes were established in 1915, funds being provided, at that time for three prizes of $50, $30 and $20 respectively, for the best essays, or other papers submitted in competition by Junior Members and Members of Affiliated, Student Societies. The original intention was to award all three during the year 1915, but the committee has deemed it advisable to extend the time for the second and third prizes, and the Secretary of the Institute will be glad to hear from any member who wishes to compete for one of these prizes. A competitor for the President's Prizes must be, at the time of submitting his essay, either a Junior Member or a Member of an Affiliated Student Society of this Institute. The essays must be upon some subject related to Mining, Economic Geology, or Metallurgy. I11 malting the awards, special weight will be given to originality in investigation and treatment; and to 'literary merit. As a general rule, the essays should not be less than 3,000, nor

Jan 5, 1917

By Charles Luner

ALTHOUGH the kinetics of the atmospheric oxidation of tin have been studied,1-3 the kinetics in pure oxygen have not been reported. This note presents some results of the kinetics of the oxidation of tin foil in pure oxygen. The tin foil used in this investigation was 99.78 pct pure, the two major impurities being Pb (0.17 pct) and Sb (0.024 pct). The foil was degreased and air-dried prior to oxidation. The air-formed film was estimated by coulometric reduction4 of the surface oxides to be about 25A. The samples, which were in strip form and had a total geometric surface area of about 300 sq cm, were first evacuated at room temperature in an oxidation bulb to 1 X 10 -5 mm Hg and subsequently degassed for 1 hr at the temperature of the experiment. Spectroscopically pure oxygen was then introduced into the bulb. The rates of oxidation were measured by following the rate of pressure change due to oxygen consumption in a closed system, the volume of which was sufficiently large so that the pressure change during an experiment was 10 to 15 per cent of the total pressure. An oil-mercury manometer,5 with a sensitivity of 3 X x mm Hg (which corresponds approximately to 5 X 10 -7 gm of oxygen) was used to measure the pressure change. The oxidation bulb was heated by an oil-bath and controlled to within -10.3 C. The reproducibility of the rates was good, as determined by the coincidence of rates at 190oC for duplicate experiments. Fig. 1 shows the oxidation curves in the temperature range 168 to 211.5oC at 8 mm Hg pressure. The effect of pressure on the rate of oxidation at 190°C is also shown. The rate of oxidation was not markedly affected by changes in pressure in the range 4 to 9 mm Hg, except perhaps at the lowest pressure, 4 mm Hg, where after about 70 min there appeared to be a decline in the rate, as compared with the rate at the higher pressures. At the lower tem- perature, 168oC, and for short reaction times, it is difficult to distinguish between a linear relationship and a slight curvature in the oxidation rate. However, for longer times, there was a somewhat larger indication of curvature. The samples after oxidation were gold-colored in appearance. The oxide that was formed at 170°C was identified as a-SnO by reflection electron diffraction. This is in agreement with results obtained by other workers.6, 7 The rate data best fitted the logarithmic-oxidation rate law, w = K1n ln(1 + -t/to) [1] where w is the weight of oxygen consumed, t is the time, and K In, and to are constants. First estimates to were obtained according to the method of Taylor Thon8 and were then employed to obtain the best simuItaneous estimates of to and K In, that would fit the logarithmic expression. These estimates were found numerically, so that the residual variance could be minimized. The calculations were performed on an

Jan 1, 1961

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By Ralph M. Hunter

Until recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged breakdown did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to bypass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdi-ness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, there- fore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 1946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1949

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By S A. Ravishankar

An overview of flotation reagents used in sulfide and non-sulfide separations, from an industrial perspective, is given in this presentation to highlight the current applications knowledge. The historical and theoretical aspects, which are well documented in numerous books and reviews, will only be highlighted, when necessary, to support the theme of this paper, viz critical analysis of reagent research, design, selection and optimisation with an emphasis on relevance to plant needs and practice. The three types of flotation reagents; viz collectors, frothers and modifiers, used currently in the industry are briefly reviewed; pitfalls and gaps, arising from somewhat arbitrary and reductionistic practice in reagent applications, are identified; and the impact of environmental regulations on current and future reagent development is discussed. The importance of frothers and modifiers, which have received less overall attention than collectors, is highlighted. The need for a rational, holistic (or ætotal systemÆ, ætop-downÆ) approach for reagent design, selection and optimisation is discussed with a view to provide remedies for pitfalls and a platform for filling gaps in reagent chemistry and applications, and to develop reagent technology that can deliver robust solutions to plant needs. Flotation Matrix 100TM, a comprehensive package designed at Cytec to incorporate all the elements of the holistic approach û viz definition of mineralogy and plant needs, rule-based expert system rational reagent selection, and laboratory and plant best practices û will also be described.No paper available for this abstract

Jan 1, 2005

By John M. Bostwick, James C. Bradbury

Bitumen is a general term for a group of materials composed of mixtures of hydrocarbons that are fusible and soluble in carbon disulfide. Included in the group are petroleum, asphalts, asphaltites, and mineral waxes. Asphalt is a dark-colored, cementitious solid or semisolid, which generally softens on heating and resumes a more viscous or solid state when cooled. It is found in native form in fissures and pore spaces in rocks and as lakes. It is also obtained from the residues produced in petroleum refining. Asphaltites are black, naturally occurring solid bitumens. They are generally shiny and break with a conchoidal fracture. Common asphaltites are gilsonite (uintahite), grahamite, and glance pitch. Mineral waxes are solid or semisolid, relatively nonvolatile bitumens of various colors, having an unctuous feel and waxy luster, Of the native waxes, ozokerite is the best known. Montan wax is also classed as a natural wax, although it never occurs in the pure state and must be extracted from lignite or cannel coal (Ladoo, 1920). Mineral waxes may also be obtained by pyroprocessing of petroleum, lignite, and peat. Pyrobitumens are dark-colored, solid hydrocarbons that are infusible and relatively insoluble in carbon disulfide. They are so-called because they will yield liquid and gaseous hydrocarbons only when heated. Asphaltic pyrobitumens are defined as "substantially free of oxygenated bodies" and include wurtzilite (elaterite), albertite, and impsonite (Thrush, 1968). Nonasphaltic pyrobitumens contain oxygenated bodies; examples are coal and peat. The nonasphaltic type will not be discussed further. Petroleum Asphalts Asphalts refined from crude petroleum have almost completely replaced the native types. Refineries can produce asphalts in every desirable grade more economically and in greater quantity than the native types and with a variety of properties that meet the requirements of the various manufacturers using them. For all practical purposes, it is estimated that more than 95% of the asphalts consumed in the United States are refined from crude petroleum (private communication). Native Asphalts Native asphalts are dark brown or black, semisolid or solid substances that, in theory, formed by slow, natural fractionation of crude petroleum at or near the surface of the earth (Goulston, 1938). They are colloidal systems of high molecular weight components dispersed in a medium consisting of low molecular weight components (Pracy, 1954). Native asphalts may occur as lakes, as impregnations of rock (rock asphalt) or as deposits consisting of mixtures of natural asphalt and mineral matter in various proportions (Stern, 1960). Practical use of native asphalt dates to about 3000 B.C. It was mined from surface pits or lakes and used, then as now, for masonry mortar, waterproofing aqueducts and tunnels, binders for road construction, and as an article of commerce (Miller, 1938). Generally the native asphalts find little commercial use today except where they are geographically abundant, easily mined and transported, or have specific or special application. Petroleum-refined asphalt is produced by unusually economical techniques and is much less costly to use. The largest and best known of the lake deposits is that on the Island of Trinidad, where the lake covers an area of 114 acres and is 285 ft deep at its center (Stem, 1960). The lake asphalt is refined by heating to evaporate in-

Jan 1, 1983