Search Documents

By M J. Schultz, R L. Rude, D M. Tomko

The US Mine Safety and Health Administration (MSHA) conducted compliance assistance diesel particulate matter (DPM) sampling throughout the underground metal and non-metal mining industry. Based on that sampling, MSHA identified mines that were having difficulty meeting the DPM limit. To provide further assistance, MSHA then visited approximately 60 of the mines that were experiencing difficulty complying with the DPM standard. As part of these visits, DPM exposures were measured and control technologies for DPM were observed and assessed. Controls consisted of ventilation, clean engines, environmental cabs, alternative fuels, diesel particulate filters (DPF) and work practices. The focus of the follow-up compliance assistance visits was to assess control effectiveness and to make recommendations to mines experiencing difficulty in meeting the DPM standard. At each mine visited, the ventilation controls were evaluated, engine emissions were determined for equipment in use, environmental cabs were examined, and operational practices were noted. Additionally, control technologies, including alternative fuels and DPF were evaluated in several mines. A comparison was made of mine and section airflow to equipment particulate indices. Based on engine emissions, horsepower and operating time, the contribution of individual engine emissions to total emissions was made. Environmental cab integrity, positive pressure and air filtration systems were checked and operational practices relating to DPM exposure were assessed. This paper summarises the preference and magnitudes of controls that were typically used or needed for successful control of DPM. Additionally, results of the assessments of alternative fuels (including bio-diesel and water emulsion fuels) and DPF are presented.

Jan 1, 2005

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988

Copper cathode and Uranium Oxide production at WMC (Olympic Dam Corporation) Pty. Ltd. involves processing leach liquors through a copper solvent extraction plant followed by a uranium solvent extraction plant. This paper discusses the processing problems, metallurgical testwork and circuit changes made due to contamination of amine in the oxime circuit and vice versa.

Jan 1, 1996

By H. J. Oterdoom

SMS Group (SMSG) has always been concerned about safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and also SMSG contributed with its design features to a safer operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMSG wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2015

By P. McGrath

From the mid-1980s through 1997, Echo Bay Alaska evaluated reopening the historic Alaska-Juneau (AJ) gold mine. Their original proposed project underwent numerous modifications in order to minimize the potential for significant environmental impacts. One of the major modifications involved changing .the tailings disposal method from a conventional tailings impoundment to submarine tailings disposal (STD). In 1995, the U.S. EPA began work on a Supplemental Environmental Impact Statement (SEIS) to assess the impacts of the STD proposal. Key features of the STD impact assessment included fate and transport modeling to determine the extent of tailings deposition and the use of ecological risk assessment to predict marine impacts during deposition and ecosystem recovery following STD. A key feature of the SEIS regulatory process included a rulemaking proposed by EPA to exempt the AJ tailings from effluent regulations. Critical to success in moving the project forward was early development of an interactive working relationship with other regulatory agencies and the public.

Jan 1, 1998

By M Sebbag, T Taimre

Barrick Gold Corporation is proceeding with development of the Buzwagi Mine in the Lake Victoria Greenstone Belt District of Tanzania. The Buzwagi orebody occurs in the Nzega Shear zone within the Greenstone Belt and is hosted in a K-Feldspar rich granite in contact with mafic volcanic. The orebody presents 2.6 M ounces in 41 Mt of reserves, at 2.0 g/t. Over the ten year mine life, total material movement will be 261 Mt. The feasibility study was completed in 2006 and presented several technical challenges. Two principle challenges are grade control and the impact of dilution on the economic viability of the project. The principle challenges for grade control will be quality control and quality assurance in the sampling of the massive coarse grained granite, which comprises 70 per cent of the deposit. The principle challenge with dilution will be with the selective mining of the narrower mineralised zones contained within the mafic volcanics. This paper will focus on the mine planning methodology which has been applied including selective mine unit (SMU) and dilution estimation, net smelter revenue (NSR) calculation and the effects of cut-off grades to the project economics and mine schedule.

Jan 1, 2007

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By Margaret Fuller Boos

Precambrian granitic pegmatites on the west, south west, south and southeast slopes of Storm Mountain, Larimer County, northern Colorado, were explored and mapped geologically 1956-1959. The area between Crystal Mountain Mining District on the north and Hyatt pegmatite mine area on the south was nearly inaccessible until a company built an access road, which was completed in 1959, into Roosevelt National Forest and its jeep-type roads. The area is extremely rugged, rising from some 6,000 feet on the highway at Drake, on Big Thompson River, to an altitude of over 10,000 feet at the summit ridge of Storm Mountain. Almost innumerable pegmatites of every possible type of granitic pegmatite intrusion infest the Precambrian gneisses and schists of the southwest-tilted fault block of Storm Mountain. The major bodies stand at least 100 to 200, feet high above the surrounding forest floor. Core drilling has shown that some extend to at least 200 feet below the surface. They blunt out at the southwest, some keel out below and others are faulted out at their southwest ends. Strike length ranges from 200 to 600 feet. The massive bulky bodies have nearly vertical walls. Contents are zoned or ribboned and layered. They consist of local commercial bodies of beryl, potash feldspar, mica, uranium minerals and quartz. As yet no lithium minerals have been encountered.

Jan 1, 1960

By A. L. Mular

Some specific cases of the collection of data from industrial grinding and classifying operations, and the development of models from the data so obtained, will be described. The problems encountered, the effort involved, and the value of the derived models in improving the plant efficiencies will be discussed and documented where possible.

Jan 1, 1971

By D. M. Ziebarth

"During the mid to late 1960s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace, supporting a large part of the world demand, until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corp. of Saskatchewan (PCS) was one of the major producers planning upgrades to its production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1.5-kt/h (1,650-stph) hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market.BackgroundPotash production is a major Saskatchewan industry and has played a significant role in the economy for more than 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) Mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in 12 companies opening 10 mines by 1970. In 1975, Potash Corp. of Saskatchewan was created by the government of Saskatchewan, and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine, near Saskatoon.Cory has been in operation since 1968 and is located 12 km (7.5 miles) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3,300 ft) below surface.PCS has embarked on sizable capital expansions of more than CDN$7 billion.The $1.6-billion Cory expansion was expected to raise operational capability of the site to 2.7 Mt/a (3 million stpy), an increase of 1.9 Mt/a (2.1 million stpy). To achieve 2.7 Mt/a (3 million stpy) of finished product and considering the 22.6 percent average production recovery (Potash Corp, 2013), 12 Mt/a (13.2 million stpy) of ore must be hoisted to the surface for processing. To deliver this rate required upgrading of the hoisting plant to 1.5 kt/h (1,650 stph). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly that the work was completed safely (Potash Corp., 2013)."

Apr 1, 2017

The last decade has seen the use of powerful computerized Mine-Wide Monitoring (MWM) systems for detecting hazardous conditions in underground coal mines. Recently, the U.S. Bureau of Mines and Jim Walter Resources, Inc. (JWR) expanded the scope of MWM system to include ground control. Single-point extensometers were installed in each of 30 intersections along a tailgate entry. These instruments monitored the rate of roof sag, a sensitive indicator of roof instability. Data were collected by the mine's own computerized MWM system. The paper describes the successful integration of ground control instruments into MWM, the data reduction procedures, and the identification of several hazardous areas.

Jan 1, 1994

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By A. J. Paul Laprairie

"ADVANCE planning of mining methods, from the first development openings to stope layout and pillar recovery, has long been accepted as a normal method of operating a mine. Recently, mine managers have become increasingly aware that advance planning of cost and accounting controls can also be considered a normal method of operation. The use of such controls is wide-spread in manufacturing industries. In mining, the gold mines of South Africa have pioneered, with marked success, in this field and have been closely associated with most of the research and field work in accounting control. Canadian mine managers are also beginning to realize the advantages of using planned costs. The control procedures which subsequently have been introduced at various mines have come to be known by such names as ""Responsibility Costing"" or Budgetary Control"".Budgetary control, the term used in this paper, is based on the concept of decentralized authority with centralized control. ;The control is achieved by measuring results against yardsticks which are in the form of budgets or standards. Bud-gets are made for the future activities of each possible operation as planned by the department head, and attention is directed to variations from this plan. Furthermore, the control process charges to each operation only those costs which are incurred directly for that operation, and which can be controlled by the person in charge. Thus, budgetary control relates results to the officials responsible for those results. Expenditures are analyzed according to the organizational structure of the mine and the people who run it, and not according to production processes."

Jan 1, 1960

By J. Illescas, N. C. Murray

This paper provides an economic comparison and technical evaluation of different approaches for copper recovery from small-scale resources such as historic tails, dumps, pond and pit water as well as acid mine/rock drainage. Factors such as the location, the availability and cost of reagents, power availability and cost and a local market for end product alter the preferred processing technique. A number of scenarios are presented and technologies considered include; solvent extraction, ion exchange, sulphide precipitation, cementation, copper sulphate crystallization, membrane (RO) and copper cathode production.

Jan 1, 2014

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By J. E. Carrasco, J. D. Stinnette, R. A. Alvarez

"Chuquicamata Underground Mine is one of the main projects for the Chilean government copper company (CODELCO). Underground mine project has been under construction since 2013 and presents a solution for the lower production levels of the open pit and prolongs the life of the mine for the next 40 years. Currently, around 2000 workers operate in the mine daily. Dozens of trucks and heavy machines drives through all main routes and access in the mine. As a mine under construction not all the infrastructure necessary to operate safely in the mine has been completed. Risk of a truck or fixed facility fire is always a challenge to keep under control. One important part of fire simulation relays on what we can do prevent a fire and what can be done with the existing infrastructure to control a declared fire and start evacuation plans. This study has been made as a feasible emergency plan to implement, in this case, of a mine under construction, were limited resources are available. Several fire scenarios have been made to support all the emergency plan strategy and a detailed step by step procedure indicates what the elements of a fire emergency plan and risk analysis are.INTRODUCTIONThe main objective of this study is to describe the importance of fire risk analyses (FRAs) and different methods to be used before commencing fire simulation and methodology steps utilized for a fire emergency plan strategy (EPS) at the Chuquicamata underground mine. It also describes how to classify zones which are going to be affected by fumes and gases propagation derived from the exact location of a fire event. Fire simulation study is helpful to determine the impact on a ventilation system with the main purpose of providing relevant information to complement emergency plans and stablished control techniques in ventilation design and its operation. Most fire simulation studies only concentrates in simulation techniques on itself. But what is the next following step in developing an emergency plan? How can we evaluate, classify and treat risky areas? This study is focused mainly in the phases before and after a fire simulation process. Phases corresponds to a good FRA and how output data can be used for an EPS."

Jan 1, 2019

By M. S. Klima

Tests were conducted to investigate the potential for recovering anthracite from preparation plant tailings. Samples were collected from tailings streams or slurry ponds of several anthracite cleaning plants. A washability analysis was conducted on each sample. The use of gravity-and surface-based cleaning processes for treating the 28x200 mesh tailings material was examined. Simulations were performed for various cyclone staging arrangements using published partition data for both water-only and dense-medium cyclones. Froth flotation testing was done on both precleaned anthracite and tailings material. Grade-yield curves were determined for various conditions.

Jan 1, 1995

By C. B. Solnordal, R. N. Taylor

"The heat transfer conditions on the outer side of a Sirosmelt lance have been determined using experimental measurements in combination with a mathematical model. By measuring the temperature distribution along the wall of an operating Sirosmelt lance, as well as the thickness of the slag layer on it, it was possible to use the model to determine both the heat transfer coefficient between the vessel contents and the lance, as well as the effective thermal conductivity of the slag layer. The effective thermal conductivity of the slag layer was found to be within the range 0.7-1.3 W.m-1. ºCl, which was in good agreement with measured values for magnetite. The outside heat transfer coefficient varied from 80 to ISO W.m-2. ºC1, which was smaller than quoted in the literature for metal/slag systems. The discrepancy was attributed to the high thermal resistance experienced between the lance wall and the slag layer, as well as the large quantities of combustion gases that envelop the lance tip and reduce convection and conduction from the melt to the lance. INTRODUCTIONThe Sirosmelt submerged combustion smelting process [1] utilizes top injection lances to deliver fuel and air into a metallurgical melt. To help prevent lance failure from attack by liquid slag, helical vane swirlers are used within the annular lance to impart swirl to the flowing air and enhance the heat transfer from the lance wall to the air. The swirlers thus cool the wall, and enable a frozen layer of slag to form on its outer surface. This solid layer ensures liquid slag cannot reach the lance surface, and the lance is protected.A mathematical model of the heat transfer processes associated with the lance has been developed, which combines heat balance equations with engineering correlations to predict the wall and cooling air temperature of the lance, as well as the air pressure distribution. An account of the model was given by Rankin et al. [2]. To further enhance the model and enable it to predict the thickness of slag accumulating on the lance, a detailed analysis of the heat flow through the slag layer commenced in 1992. By far the most complex aspect of the model, the flow of heat from the vessel contents to the outside of the lance was dependent on many factors, including:-"

Jan 1, 1996

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016