Search Documents

By Batric Pesic

Recovery of gold from refractory ores was studied by pressure oxidation as the method of ore pretreatment followed by bromination of oxidized residues. Three different ores were examined, Au-Ag, Au-Ag-Te, and Au-silver free ore. Pyrite was the major host mineral for gold in these ores. The effect of pressure oxidation parameters (temperature, pressure of oxygen, time, and pulp density) on subsequent bromination under standard conditions was examined. Bromination of residues produced under standard pressure oxidation conditions was examined as a function of: temperature, bromine and sodium bromide concentration, and time. Recovery of gold on activated carbon, from the pulp after bromination, was studied too. Recovery of gold from silver containing ores was lower (87-91%) than the recovery of gold from silver free gold ore (97%). In each studied case, the presence of activated carbon in the pulp further increased the recovery of gold.

Jan 1, 1992

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By J. J. Brummer

"A reconnaissance geochemical survey, using the stream sediment technique, is described. The survey covered an area of about 400 square miles, in the Seal Lake area of central Labrador, underlain by basaltic flows, diabase and metadiabase sills, and sedimentary rocks. Previous work had indicated numerous small copper occurrences within the Seal Lake group of rocks. Stream sediments were tested for the readily extractable copper content and total heavy metal content. The results of the copper survey did not yield any new data on the distribution of copper mineralization. Results of the total heavy metal survey attracted attention to a remote portion of the area (Ten Mile Lake), which had hitherto been regarded as having no economic interest. The anomalous values found, suggested that zinc mineralization should occur in this region. Geological mapping indicated that the rocks exposed belonged to the Letitia Lake Group, which is older than the Seal Lake Group exposed to the east, which contains the copper mineralization of the district.Investigation of the area lead to the discovery of: (1) uneconomic lead-zinc mineralization; (2) radioactivity extending over a considerable area. Evaluation of the radioactive rocks led to the discovery of columbium-thorium mineralization in amphibolite and in diopside-actinolite schists along a contact with intrusive alkali syenite.Thus a geochemical survey, which was planned to evaluate a copper province, resulted in the discovery of lead-zinc-columbium-thorium mineralization."

Jan 1, 1960

By D. W. Duncan, A. Bruynesteyn

Acidic mine waters containing solubilized uranium have been observed in many uranium and some copper mines. In every case, the sulphide and iron oxidizing bacterium, Thiobacillus ferrooxidans, was also present. This bacterium provides the ferric iron required to oxidize u+4, both by oxidizing available ferrous iron and by oxidizing pyrite or other available sulphide minerals. This latter oxidation also provides sulphuric acid and may increase extraction by exposing more uranium. The enhancement of bacterial activity and the results of some field tests are discussed.

Jan 1, 1971

By E. Zucker

In this paper, as in the 1960 CIM paper of the same name, s1gmf1cant new developments in electrical-mechanical mining equipment are briefly described. These include static thyristor-supplied D.C. drives for mine hoists, load-haul-dump systems, process controls with small and medium-size computers, and several other new items of equipment and Concepts. All the new hardware descriptions are given in the context of over-all process integration. This means the actual mechanical linking together of two or more processes and the preliminary step in the development of production-line mining.

Jan 1, 1969

By Fazel G. Jahromi, Ahmad Ghahreman

"Several studies were performed on the atmospheric leaching of copper sulfide minerals in the presence of activated carbon and a new catalyst, AF 5. AF 5 is a carbon based catalyst with similar properties to those of activated carbon however much better mechanical properties. The activated carbon surface chemistry has been investigated in various studies; however the connection of the surface chemistry of activated carbon and AF 5 with the sulfide minerals during the atmospheric leaching process is not well-understood yet. Based on the surface analysis, AF 5 showed higher surface area than activated carbon (AC). Adsorption and oxidation of copper, arsenic and iron ions in the presence of different activated carbon were investigated. Adsorption properties of both catalysts were similar and 18-24% of iron, 12-18% of copper and 10% of arsenic adsorbed on the catalysts surface form 5 g/L Fe(III) and Cu(II) and 2 g/L As(III) at 80°C. In oxidation experiments, both catalysts reduced Fe(III) and Cu(II) ions and re-oxidized the reduced species in the presence of oxygen and oxidized As(III) ions. The addition of oxidizing ions can enhance the oxidation process kinetics and increase the catalytic capability of carbon.INTRODUCTION Hydrometallurgical processes of copper sulfide concentrates are under development and various different methods have been proposed to increase the atmospheric leaching rate of copper sulfide minerals. These methods include using different media, reagents, and catalysts. Among different methods, leaching of the copper sulfide minerals in the chloride media has some advantages over sulfate media. Smaller scale of operation, increased leaching rates, and lower sulfate formation are some of the benefits of the chloride leaching media over other similar media. Moreover, using ferric and cupric ions as oxidants and utilizing activated carbon as a catalyst has been proven to enhance the leaching rate of copper sulfide minerals effectively. Activated carbon (AC) and AF 5 (micro porous carbon based catalyst) are two of the most efficient and practical catalysts in copper sulfide leaching processes. AC can enhance the copper recovery of enargite in chloride media from 69% to 92% after 96 hours of leaching under the similar conditions (Jahromi & Ghahreman, 2016). It has been shown that AC at acidic pH can generate hydrogen peroxide in the presence of oxygen which can leach copper minerals (Ahmumada et al., 2002)."

Jan 1, 2017

By George F. McIntyre

The subject of this paper is mineral processing chemicals - how they work and where they end up environmentally. First of all, it is necessary to recognize that water is the most universally and widely used chemical used by the mining industry to separate desirable minerals from unwanted wastes, sands, and slimes. Of the total world's water supply, over 97 percent is found in the oceans. Another two percent is tied up in the ice caps, leaving roughly only one percent for us to work with. This one percent is distributed either as ground or surface water and makes up the bulk of all water used industrially. Even with such a small proportion available for immediate use, there appears to be enough fresh water to meet our needs for at least another hundred years. This availability, however, depends heavily on how we handle our waste waters, how we process them, and how we plan for their reuse. Certain governmental agencies have been charged with the task of setting up standards of water quality which must be met prior to environmental discharge. There is even discussion of zero discharge from industrial operations. Due to limited supply and availability, the mining industry has always been forced to reuse its process water or to treat it prior to discharge. Consequently, we are in an enviable position and are presently able to live with the environmentalists demands. To stay on top of the situation, it is necessary to continually concern ourselves with the .effects of changing orebodies and reagents on the final mill effluent. From a process standpoint, it is also important to recognize the impurities of plant recycle water and how they might tend to influence overall operations

Jan 1, 1974

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

RME has a vision for a new mill operational paradigm made possible by RMEÆs fast, safe Mill Relining System. This vision can be moved forward into reality at any time with or without guidance from recent development in measurement and predictive modelling tools.Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by optimising liners for life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to design new liners for maximum commercial performance. This may mean more frequent changes of liners but with liners designed to yield optimum grinding, metallurgical and profitability performance. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. This paper provides an update regarding RMEÆs fast, safe Mill Relining System technologies and outlines RMEÆs vision of a æliner profile versus profitabilityÆ model as a function of metal price, developed intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2006

By James O'Brien, Lyman Frost, S. Elangovan, J. Stephen Herring, Joseph Hartvigsen, Carl Stoots, Anthony Nickens

"Carbon dioxide recovered from concentrated sources, such as metallurgical reduction furnaces, cement kilns and fossil power plants can provide a valuable feedstock for a synthetic fuels industry based on energy from nuclear, solar, wind and hydropower sources. High temperature co-electrolysis of CO2 and steam to produce synthesis gas has been demonstrated using reversible solid oxide fuel cell technology. Where a source of high temperature process heat is available, such as from an advanced high temperature nuclear reactor or solar dish concentrator, the endothermic electrolysis reactions can utilize both thermal and electrical inputs in such a way that the conversion efficiency within the cell is 100%. Synthesis gas produced in a coelectrolysis cell has been further reacted over a catalyst to produce conventional hydrocarbon fuels. Widespread implementation of synfuel production from CO2 will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles.IntroductionFor the past several years, Ceramatec, Inc and the Idaho National Laboratory (INL), have been studying the feasibility of high temperature solid oxide electrolysis for large-scale, nuclearpowered hydrogen production under the U.S. DOE’s nuclear hydrogen initiative (NHI) as an alternative to the thermochemical process. Parallel to this effort, the INL and Ceramatec have been researching high temperature co-electrolysis of mixtures of steam and CO2 to produce syngas:"

Jan 1, 2008

Ground falls (roof and rib) have historically been responsible for nearly 50% of all fatalities in bituminous underground coal mines. In recent years, the number of some annual ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, the twin disasters at Crandall Canyon in 2007, in which nine miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990s, these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents since 2005. Progress has also been made in pillar recovery, where there has been just one fatal incident since 2005. On the other hand, more than 300 miners continue to be injured each year by rock falling from between supports and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities available technologies such as roof screen, rib bolting and inside control roof bolters could reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety.

Jan 1, 2011

By J. Eloranta

"Previous work indicated that the annual per-capita consumption of raw aggregate material averages about 10 tons; half of which is produced by blasting. Given a population of approximately 320 million in the United States alone, this amounts to 1.6 billion tons of blasted material annually. It was also estimated that up to 20% of the blasted material in aggregate operations is smaller than 6.35 mm (1/4inch) in size. Thus, about 320 million tons (i.e. 1 ton per capita) of byproduct is produced annually and sold at significantly lower prices or potentially discarded in waste dumps."

Jan 1, 2017

By C. Musingwini, M. Mohutsiwa

"SynopsisCapital cost estimates are important in decisions on whether a project will be approved, mothballed, or abandoned. In South Africa, junior coal miners do not have extensive databases of historical projects from which to estimate capital costs. The purpose of this paper is to establish formulae that can be used for estimating capital costs of developing coal mines in a coal-producing country, using South Africa as a case study. The costs are estimated to an error of magnitude level of -30% to +50%, which is suitable for a concept study level, using a parametric estimation technique. The study uses data from completed coal mining projects from selected coal-producing countries. Three formulae are developed and presented for estimating capital costs of underground bord and pillar, surface shovel and truck, and dragline operations.IntroductionCapital cost estimates play a critical role in deciding whether projects will proceed, be delayed, or abandoned. It is therefore important that capital cost estimates are carried out accurately as determined by the estimation guidelines based on the level of estimation conducted (Shafiee and Topal, 2012). The lack of literature on estimation of capital costs in many coal mining countries is adversely affecting junior coal miners, since they do not have an extensive database of historical projects on which to base estimations. In South Africa, the difficulty in estimating capital costs is attributable to lack of publicly available data on completed South African mining projects (Hall, 2013)."

Jan 1, 2015

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives (HydroStar® 4208, DXG®-F7, Cyquest® N-900) using a potentiostatic technique. The current-time data obtained at 0.16V vs. SHE was analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A m-2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current-time data from the electrolyte without organic additives indicate progressive nucleation with two-dimensional (2-D) growth under diffusion control. SEM images obtained confirmed progressive nucleation with 2-D growth. 20 mg/L Cl- and 2.5 mg/L organic additives did not change the nucleation and growth mechanism, however the additives increased the number and reduced the size of copper nuclei leading to more uniform coverage of the stainless steel substrate.INTRODUCTION Electrowinning of copper is an important process in the manufacture of high purity copper metal. It is approximated that 20% of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole, and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth, and nature of the initial deposit (Sun and O'Keefe, 1992). Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature, and copper concentration, small amounts of organic smoothing agents (traditionally guar products) are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper dendrites, which leads to improved deposit quality by producing bright, smooth, and dense cathodes."

Jan 1, 2015

By Edward Sampson

Bases of National Power At a time when the economy of the world is in a particularly troubled state it is appropriate to examine some problems of the distribution of natural resources. I should like particularly to call attention to the remarkable increasing demand for natural resources, to give an analysis of the demand for certain mineral resources, and to direct attention to some problems in satisfying this demand. All industrial power is based on natural resources and the most basic of these are soils, energy resources, and mineral resources. There is a strong interrelation of these resources, more than is obvious, and I shall take up certain aspects from the point of view of a geologist. Few nations are well endowed with all three of the kinds of natural resources I have mentioned and much has been done by some small countries whose peoples are industrious and enterprising and where conditions for free world trade have been favourable. However, major industrial power is dependent on a substantial endowment of all three classes.

Jan 1, 1949

By R. R. Rogers

Abstract The degree of cathodic protection of steel and the anode corrosion rate were determined when anodes and waters of different compositions were used at temperatures similar to those in domestic hot water tanks. Twenty different anode materials, sixteen of them magnesium-zinc-aluminium alloys, were immersed in six different synthetic waters resembling those to be found in various parts of Canada. The results showed that (1) both the degree of cathode protection and the average anode corrosion rate are affected materially by the composition of the anode material and of the water; (2) poor cathode protection is associated with low anode corrosion rate; (3) when the cathode is fully protected, the anode corrosion rate may be comparatively low or comparatively high, depending upon the composttion of the water; (4) an important relationship exists between the magnesium content of the preferred anode and the composition of the water; (5) the degree of protection is increased as the SO4 + Cl concentration of the water is increased and thus as its specific resistance is decreased. Introduction Fairly recently, the use of the active metal magnesium for the cathodic protection of less active metals has received a considerable amount of attention. This interest has been stimulated by the fact that the wartime demand for magnesium was greatly in excess of the present peacetime demand and there is a natural desire to continue operating the large magnesium plants which were built during the war. Information regarding the use of zinc and aluminium for this purpose also has been published. There is a great demand for domestic hot-water tanks which will resist corrosion satisfactorily. This problem is rather complex in view of the fact that the composition of the water used in such tanks varies greatly and depends upon the locality. The present investigation deals with the effect of water composition and anode composition on the cathodic protection of steel under conditions approaching those which exist in hot water tanks.

Jan 1, 1948

By Charles E. Michener

This paper deals with the occurrence of basic and ultrabasic rocks and their relationship in space and time to major structures of the earth. In order to introduce the paper properly, I must go back a little and try to put the subject in perspective. In the brief time that geology has been a scientific occupation, ore deposits have been grouped and classified in various ways depending on the theories that happened to be popular at the time. Some of the early scientists said that ore came from fire, other schools argued that ore originated from water. Then came the lateral secretionists and in later years the hydrothermalists led by the Lindgren school and the latter has largely been accepted as the modern concept of ore deposits. It now seems apparent that the hydrothermal school is being seriously challenged by other schools of thought. It also seems that we have reached the point where we should be willing to admit that we do not really know in most cases how the ore got to its present position. However, for practical purposes, we can classify ore deposits as to the environment in which they do occur. This is not difficult and gives the field geologist and the mining engineer something to work with and to believe in, and it gives them a basis for carrying out their field work. On the screen, Figure 1, there is a classification of ore deposits based on the environment. Under each classification is listed the more prominent metals which are characteristic of that

Jan 1, 1971

By R. D. Leitch

"REASONS FOR AND PURPOSE OF WORKIn 1924 the United States Public Health Service was requested to undertake a special study of stream pollution. At that time the proposal that the United States Bureau of Mines take up the study was made by the Public Health Service because in point of training and experience the personnel of the latter was considered not to be as well, suited to this type of investigation as was that of the Bureau of Mines. H. Foster Bain, then Director of this bureau, promised to undertake the work, and, accordingly, field investigations were begun in the spring of 1925. The problems of mine-drainage wastes and of gas-house and coke-oven waste were investigated in the laboratory, and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau of Mines experiment stations, while in Germany in 1924, where he was shown a practical application of the process, but no information was obtained as to definite chemical or mechanical processes. Because of the then pending American patent application by the German firm, we made no attempt to develop our findings further. Shortly after, a similar method of treatment was developed in the United States, and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage.SCOPE OF WORKAt the time our work was begun there was such a diversity of opinion on the whole subject and apparently so little was accurately known, that it was decided to undertake a basic study from which (1) certain definite information might be evident, and (2) what might be considered side issues of the original investigation would be suggested for subsequent study.A stream in a district thought to be representative of those in low to average sulphur bituminous coal fields and another in a high sulpbur district were selected for study, A fair (weber of factors entered into the tentative selection of these streams, the chief ones being their accessibility and freedom from other industrial or domestic pollution, besides, of course, the presence of mine drainage in these streams."

Apr 1, 1931

By Charles R. Barnhart

The Nitrogen Dioxide Cloud: After one year of testing it can be stated that we do know and understand a great deal about why the nitrogen dioxide formation is exacerbated in cast blasting. Picture 1 is an example of how concentrated the NOx can be from a cast blast. It has long been felt that 300 or more milliseconds of timing needs to be put between each row of detonations to allow the rock a maximum time of flight so the cast percentage is high. Our experiments have found that higher cast percentages can make with timing between 150 to 200 milliseconds between rows. Picture 2 show a definite improvement in nitrogen dioxide concentration and most of that was the result of shooting a previously shot end of the cast pattern that had not been dug, thus no confinement of the powder columns.

Jan 1, 2004

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970