Search Documents

By Martin Grenon

This paper presents two case studies where fracture set orientation was quantified using three methods: a simple fracture pole grouping, a Fisher distribution and a Kent distribution. The three fracture orientation representations were then used as inputs for kinematic slope stability analysis. Differences showed up in the probability of sliding for all instability modes considered.

Aug 1, 2013

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Erika Gusmão, Daniella Cardoso Buzzi, José Roberto de Oliveira

"This study evaluated the Salvinia sp action on metals biosorption in a synthetic sample of acid mine drainage (AMD) in order to determine the time and amount of metals uptake. Biosorptives tests were realized varying the contact time of 5, 20, 60 and 240 minutes. And keeping constant the follow parameters: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). In order to quantify the metals concentration captured by biomass, the AMD samples will be analyzed by ICP. Biosorbent, Salvinia sp., will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. The infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests.IntroductionThe current emphasis on environmental sustainability leads the industry in general, to treat their waste. The human activities are increasing, highlighting the industrial and mining activities, and have promoted the contamination of soil, waterways and groundwater by metals (1). The waste must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.This means the importance of studies of economic and effective methods to eliminate these metals from wastewater generated. The bioindicators are good investments in this area. The aquatic weeds are plants that inhabit swamps up from truly aquatic environments. They have several morphological and physiological adaptations that enable them to colonize the various aquatic environments. They are used as bioindicators of water quality and have also been used in decontamination of aquatic environments, production of biomass for livestock feed, fertilizers, soil and fish tanks (2)."

Jan 1, 2012

By James N. Brentz

This paper deals briefly with the problem of efficiently selecting the most cost effective haulage truck. Problems and factors are identified that effect productivity and operating cost. Despite the sophistication of computerized vehicle simulation programs, there is a wide disparity in accuracy and methodology, particularly in dealing with the various elements of cost.

Jan 1, 1984

By D. H. Davidson

The basic principal in the ISL process involves the recovery of metal values by moving fluids through rock instead of moving rock. The process combines surface and sub-surface operations, with the economic performance controlled by four major factors; rates of fluid injection and production from wells; the rate of mineral solubilization; the volume of rock swept by the fluid; and the volume of solution processed through the system. This paper discusses various technical and economic parameters affecting these four factors and how they impact project costs.

Jan 1, 1985

By G. Diáz

The PLACID process applied to the recycling of spent lead-acid batteries is being developed by an European Consortium within the Brite-Euram II programme. The status of the project entitled "Lead Recovery from Lead Oxide Secondaries" is described in this paper. The main laboratory and batch experimental results and the preliminary feasibility study are summarised. The description of the demonstration pilot plant and continuous campaigns programme for 1995 are also included. An interesting global approach is proposed, integrating the Placid process in the existing spent battery recycling pyrometallurgical facilities. This yields important improvements in the overall process. Grids would be easily treated by the conventional pyrometallurgical route, obtaining lead alloys,, while battery pastes, slags and fumes would be fed to the Placid process, obtaining pure electrolytic lead (>99.99 %), ideal for battery paste manufacturing. The implementation of the Placid process into the existing battery recycling pyrometallurgical facilities is analyzed from technical, environmental and economical viewpoints. Greater overall lead recovery, lower operating costs, reduced waste production, environmentally safer residues and much better lead product quality are the key advantages. The authors draw the following final conclusion : Integration of the Placid process with conventional pyrometallurgical treatment is a feasible and very attractive alternative route for spent lead-acid battery recycling.

Jan 1, 1995

By Bill Morgan

This paper discusses the economic zones of application for several different types of earthmoving equipment: dozers, wheel loaders in load-and-carry applications, wheel tractor scrapers, articulated trucks, rigid-frame trucks and wagons. Only the medium to large pieces of equipment were considered. From this chart (Figure 1), you can see the size range, in tons of carrying capacity, of Caterpillar equipment and the specific models analyzed.

Jan 1, 1994

By SeyedBijan Mahbaz

Development of Geomechanical Earth Models (GEM) is a prerequisite to reservoir management, involving issues such as stress path analysis, prediction of induced seismicity and sanding initiation, and coupled flow-stress modeling that leads to more realistic predictions of oil rates and rock response. Part of GEM development is the stipulation of the 3-D lithostratigraphic disposition (geometry) which is used to choose the geomechanical units. The digital geological model is then populated with quantitative and semi-quantitative data on rock properties, fluid properties, saturations, initial conditions (p, T, [_]) and other information. Both fluid and solid properties are needed this requires integration of geomechanics skills with geophysical and rock physics skills, and this article deals with a subset of this integration process, with an example from two wells in southwest Iran.Rock physics approaches are used to predict reservoir rock and fluid properties with wellbore and 3-D seismic data, which are also used to interpolate rock mechanics properties to the inter-well regions. The first step in a generic rock physics approach is diagnostic and involves the introduction of a suitable Rock Physics model.Acoustic impedance (AI), shear impedance (SI), and density (_) are the fundamental rock properties usually derived using AVO equations, and these parameters, along with attenuation coefficients, can then be correlated to static rock mechanics properties that define deformability and perhaps even strength. In this study, Poisson Impedance is introduced as a new seismic attribute used for lithology and fluid differentiation in the FahliyanFormation (reservoir rock) in two oil wells in the southwest of Iran. To do this, a novel rock physics model was developed for this naturally fractured carbonate reservoir.Currently, these data are also being used to correlate to a limited rock mechanics data base to develop a more extensive GEM to serve as input to more general geomechanical and reservoir modeling tasks.

Jun 1, 2012

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

By R. H. Hanewald

INMETCO, a subsidiary of Inco Limited, is the only facility in North America that provides High Temperature Metals Recovery for nickel-, chromium-, and iron-bearing wastes. Since 1978, this process has prevented more than 775,000 tons of materials from becoming part of the nation's waste stream. The paper describes Inco's experience in metals recovery, traces the development and explains the operation of the High Temperature Metals Recovery Process, and examines the procedures and criteria used to determine whether spent catalysts meet process feed specifications. An overview of the current requirements for transporting spent catalysts is provided. The paper concludes with brief case histories of catalysts users employing High Temperature Recovery to manage spent catalyst.

Jan 1, 1995

By D. Purdie

"This paper aims to remind researchers, designers, operators, and managers about the benefits of seeding in the design of precipitation stages in their flowsheet. Including a high density solids (HDS™) process encourages the precipitating solids to form on the surface of existing precipitated particles. This paper discusses the application of the HDS technology at Kennecott Smelter, where the authors have witnessed significant improvements in settling and filtration rates. The authors have also applied this technology at various smelter bleed treatment plants worldwide with similar improvements in precipitation and filtration rates. HDS is a registered trademark of De Nora Water Technologies. RÉSUMÉ Cet article a pour objectif de rappeler aux chercheurs, aux concepteurs, aux exploitants et aux administrateurs les avantages de l’ensemencement dans la conception des étapes de précipitation de leur schéma de traitement. L’introduction d’un procédé des boues haute densité (procédé HDS™, de l’anglais high density sludge) encourage la formation de substances solides précipitantes à la surface des particules précipitées existantes. Cet article porte sur l’application de la technologie HDS à la fonderie Kennecott, où les auteurs ont observé des améliorations importantes au niveau de la vitesse de sédimentation et de filtration. Ils ont également appliqué cette technologie à diverses usines de traitement des rejets liquides des fonderies dans le monde entier, et ont constaté des améliorations similaires en termes de vitesse de précipitation et de filtration. Le procédé HDS est une marque de commerce déposée du fabricant De Nora Water Technologies.INTRODUCTION In 1966, the lead author worked as an assistant smelting metallurgist for the Tsumeb Corporation Limited copper and lead smelter in Tsumeb, Namibia. The smelter produced copper and lead, as well as cadmium and arsenic trioxide as byproducts. The cadmium was concentrated in the lead blast furnace off gas dust, and was collected by a baghouse. The baghouse dust was leached with dilute sulfuric acid (H2SO4) in a batch process. The iron and arsenic in the solution were oxidized with potassium permanganate (KMnO4) and basic ferric arsenate (BFAS; Fe(AsO4)x(SO4)y(OH)z·wH2O) was precipitated using milk of lime. The cadmium was cemented from the purified solution using zinc dust."

Jan 1, 2018

By R. G. Coyle

"In an earlier paper the author explored the consequences of price-stabilizing effects, on an industry-wide basis, of various production strategies. These ideas have now been applied to an illustrative case of an individual mine. It is shown that the turning of production and financial policies can affect financial performance over a five-year period by as much as 22 per cent.No generality is claimed for the results and they would differ from mine to mine. It is, however, asserted that the results show that the proper turning of production, reserves and financial policies are more critical determinants of mine performance than has been realised. It is also asserted that the methods of dynamic analysis are the most appropriate means for studying this policy-design problem."

Jan 1, 2014

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010

By Cory Loukides, Cathy Aimone-Martin

Blaster training manuals used by the Office of Surface Mining (OSM) and others are outdated and cumbersome. A new approach has been developed using Microsoft PowerPoint with a Visual Basic overlay to produce modules on CD’s that present state of the art blasting techniques. The education modules contain enhanced information on topics such as explosives and initiation products, blast design, drilling, and vibration control. The content is based on safe practices and illustrated with numerous photographs and movies. Review questions, complete with explanations for incomplete answers, enhance the learning process and keep the blaster involved. The benefits of using an electronic format include the ability to continually change and update the training modules as new products, technology and applications become available. In addition, the blaster can work at home in preparation for class work and may reduce the time away from the job. This poster session presentation will allow potential users to view and take part in the evaluation of these modules.

Jan 1, 2004

By Claudio L. Schneider, Peter R. King, Reiner Neumann

"Predicting the liberation spectra that are produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.A coal sample is used here to demonstrate the procedure. It is concluded that the conditional, on length, linear grade distribution can be predicted in the same fashion for multi-phase systems. Accurate stereological conversion is the practical hurdle to be overcome for multi-phase systems, but it is already a reality for 3- phase systems."

Jan 1, 2003

By Chee Theng

"It is not surprising that the most popular key takeaway from the Developing Diversity in Mining workshop (see box) held on the first day of the SME Arizona Conference in December was, “Have more parties!”The adage that mining professionals work hard and play hard was clearly demonstrated at the two-day conference in the JW Marriott Tucson Starr Pass Resort & Spa in Tucson, AZ. Nearly 550 participants, some of whom had left behind frigid temperatures and thick parkas in their hometowns, attended a full slate of technical sessions, shared industry experiences and knowledge, reconnected with buddies in the industry, and made strategic new contacts in the conference’s collegial environment, aided by the mild Arizona winter.To start off the technical sessions, John Mansanti, president and chief executive officer of Crystal Peak Minerals and 2017 SME president, entertained a packed lecture room with his keynote lecture on “Tariffs, Embargos, and Cartels ... Oh My! A Perspective on Potash.” Mansanti gave the audience the benefit of his more than 35 years of experience at companies including Barrick Gold, Newmont Mining Corp., Placer Dome, Freeport-McMoRan and Intrepid Potash, where he was senior vice president for operations, technology and strategy. At the luncheon, Justin Cross, general manager of Freeport-Mc- MoRan’s Bagdad operations, spoke on how the role of a leader in mining is transforming from one based on technical expertise to one based on the ability to collaborate, to lead and to adapt to changes in technologies and skill sets, in his talk on “Knowing When to Learn, When to Lead and When to Manage.”"

Feb 1, 2019

By J. L. Huisman

Bio(hydro)metallurgy is the latest development in the ongoing search for efficient and economic metal winning processes. In addition to bioleaching, other biotechnology-based applications are becoming more and more accepted. In this paper the THIOMET process for general effluent treatment is described. With this process, it is possible to produce sulfide on-site and on-demand and to use the sulfide to precipitate metals, even selectively when required. The process is ideally suited as a treatment to remove metals after, for example, an acid regeneration process. Another process is proposed that deals with stainless steel pickling bleeds. Such effluents typically contain nitrate, iron, nickel, chromium(VI) and other species. This one process handles these compounds, as well as other metals.

Jan 1, 2006

By W. A. Haley

This paper discusses how a large wheel loader should be equipped, with particular attention paid to tires and tread life, and describes the several steps that can be taken to provide favorable working conditions and reduce over-all costs. A comparison is then made of wheel loader production and costs vs those of power shovels, and the present and possible future applications of the wheel loader are outlined.

Jan 1, 1969