Search Documents

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By D Cork, R Peet

"Methane is a signifi cant greenhouse gas. Methane is released from coal seams during the mining process, both in surface and underground operations. This uncontrolled release is termed æfugitive emissionsÆ and in underground mines is transferred to the atmosphere in ventilation air, known as ventilation air methane (VAM). The global VAM emissions are over 369 Mt of CO2-e/a (Butler, 2011; US EPA, 2010). Coal mines may abate this VAM or consider abatement should there be a price on carbon. These fugitive emissions are heading towards ten per cent of AustraliaÆs emissions by 2020 (Department of Climate Change, 2011).There are safety issues involved in VAM destruction. Due to the nature of coal, and coalextraction, unpredicted methane spikes above the lower-explosive-limit (LEL) can occur in theventilation air; for example outburst events or ventilation failure. This could lead to a mine fi re ifthe mine ventilation air was connected to a VAM abatement plant and the risks are left unmitigated.CorkyÆs is working with the mining industry to directly address these safety issues. CorkyÆs calltheir technology VAM RAB, which stands for ventilation air methane regenerative afterburner(VAM RAB). VAM RAB utilises the principles of a thermal oxidiser.This paper discusses fi ve independent layers of protection (ILPs) to fi rst stop methane reachingthe thermal oxidiser and secondly prevent the fl ame front from burning away from the VAMRAB. The test work completed or contemplated includes safety integrity level (SIL) assignmentto various vents, barriers and door systems to prevent a fl ammable mixture reaching the VAMRAB, proven rapid response methane monitoring sourced from the petrochemical industry, anddefl agration experiments to test the eff ectiveness of the passive geometry and active engineeringcontrols. These experiments and SIL assessments indicate that it is possible to safely connect theVAM RAB to a working coal mine.Further work is required to upscale the pilot safety work. Refi nement to the design is possible;for example improvement to safety duct controls once trialled at demonstration scale plus thermalenergy capture for power generation or other applications to provide heat. Nevertheless, thispaper shows how safety issues can be managed by a multilayer of protection approach usingvents, barriers and doors, and appropriate thermal oxidiser geometry."

Jun 1, 2012

By Richard Havens

A flotation procedure was devised by the Federal Bureau of Mines for beneficiating Mount Wheeler, Nev., beryllium ores that contain the beryllium minerals bertrandite and phenacite in a complex association with calcite, fluorspar, mica, quartz, and other accessory minerals, The method also has proven to be effective in trials on ore from the Lake George, Colo., area. Samples used in most of the research ranged from 0.49 to 0.73 percent BeO. Beryllium mineralization varied from two-thirds bertrandite to all phenacite. An unusually high grade sample containing 5 percent BeO as phenacite was floated on a batch basis to prepare concentrate for utilization studies. The beryllium minerals were floated from undeslimed pulps at natural pH using sodium fluoride and sodium hexametaphosphate (HMP), as modifiers, and a fatty acid-fuel oil combination as the collector. Key factors were the use of a minimum of about 4 pounds of sodium fluoride and between 2 and 4 pounds of HMP per ton of ore. Efficacy of the HMP was related to the grind, mineralogical composition, corollary reagents, and type and time of conditioning. Addition of the fluoride, HMP, and collector in that order, followed by appropriate conditioning after each addition, was essential for satisfactory flotation.

Jan 1, 1961

By L. Mallett

The changing demographics of the mining industry make successful passing of knowledge and skills to the next generation critical. Training methods and technologies are being developed to meet this need. Twenty years ago classroom training was largely a one-way transfer of knowledge through instructor lectures. In contrast, instructors today can use virtual reality technologies to guide trainees as they fully participate in learning experiences. Trainees can interact with the virtual work environment, co-workers, and equipment without being exposed to workplace hazards. The speed of advancement in mine safety, health, and production training shows no sign of slowing in the next 20 years. Researchers at the National Institute for Occupational Safety and Health have studied and participated in the evolution of miner training. A look at training materials they have created in the past and those they are currently developing reveals changes in methods and technologies over time and also key characteristics which have remained constant. Possibilities for the future can he discussed in the framework of an implementation of virtual reality in new miner training sessions. The example computer-based training package teaches new miners to read mine maps and provides opportunity to practice navigation skills in a virtual mine. With this 'serious game', trainees experience the look and feel of moving through an underground coal mine while in the safety of their classroom. During field-testing in 2007, trainees and instructors responded very favourably to this new way of learning. The software was usable by mine trainers with even limited computer expertise and could be installed on the affordable computers they were using for their more traditional slide presentations. The Underground Coal Mine Map Reading Training's foundation on past successful development strategies and its acceptance by today's instructors and trainees provide valuable lessons for developing training materials, strategies, and technologies for mining's future.

Jan 1, 2009

The major technological advances of the last 30 years have profoundly reshaped mining practices. Machines keep getting bigger while productivity continues to increase and manning levels drop. These trends will continue and the introduction of breakthrough technologies will continue to accelerate, driven by a continued focus on lowering the cost of production, improving the productivity of workers and machines, and ensuring safer working environments. At the same time, global consolidation of mining companies has impacted on technology development in a range of ways. There are many potential technologies being proposed, some already operating in Australian mines. The automation of underground load-haul-dump (LHD) trucks for example, continues the process of removing workers from the most dangerous operating environments. Global positioning systems fitted to draglines, fibre optic communication channels, and 400 tonne trucks are only some examples of what lies ahead. However, where we need to return focus is to the technology of management û which is also one of the two key interrelated themes of this keynote address. Have we, as an industry, adequately been able to keep up with technological advances? Are our management systems as competent as the machinery we employ? The other key theme is the processes of globalisation and consolidation. What are the impacts on our industry? What are the implications of these processes, particularly for the ways in which we manage our people? My paper is divided into several components:some comments on the coal industry and the dramatic restructuring we have seen in recent years; in the context of this restructuring, an overview of my company and its evolution; my views on the role of contractors; some comments on the consolidation also occurring in the mining machinery and equipment, technology and services sectors; some observations on two major areas of technology û drill and blast; and trucks, shovels and excavators; the implications of consolidation and new technology for our employees and management; and finally some comments on research programs.

Jan 1, 2001

Jan 1, 1885

By C. A. Lavery

A DISCUSSION is presented of natural gas production and field processing equipment as now utilized in the gas producing areas of the United States, with reference to use of such equipment in Canadian gas areas. The scope of the paper is confined to a general description of various types and methods of using surface production equipment. The discussion is divided under two general groups: well-head production equipment, and field processing. The first will be concerned primarily with indirect heaters, separators, knockouts, and special versions of this equipment. The second major group includes the field processing equipment for handling natural gas. A delineation should be made here as to the meaning of field processing as used in this discussion. We will limit our term to mean such processing equipment as may be used in producing fields to process gas or its by products in a manner that does not require conventional plant practices either in operation or supervision. This covers such equipment as is necessary to complete preparation of gas for sale to pipeline and/ or is necessary to recover valuable components. Under this heading we will discuss glycol dehydration, solid desiccant dehydration, low-temperature separation, mechanical refrigeration, and desorbtion-stabilization. These are all processes involved in preparing gas for final sale or disposal. They do not include the more conventional and large-scale plant process systems.

Jan 1, 1956

By H. B. Salisbury

As a part of a research program designed to help minimize national requirements for new mineral commodities by maximizing recovery of metals from domestic secondary resources, the Bureau of Mines investigated the development of economic methods for recovering copper and associated metals from complex electronic scrap. Three types were selected for research: (1) multiple-pin plugs and connectors, (2) obsolete aircraft radio assemblies, and (3) the magnetic fraction of shredded electronic scrap furnished by the Bureau's Avondale Research Center. The plugs and connectors, after incineration to remove plastic components and melting, yielded a brittle ingot, as did the internal portion of the radio assemblies. The brittle ingots were ground to minus 35-mesh for processing, and the magnetic material was used in the as-received condition. A process using pretreated or raw scrap as a copper precipitant in various concentrations of acidulated copper sulfate solution was developed as a means of effecting an initial separation and upgrading in the form of high-grade cement copper containing all or most of the precious metals.

Jan 1, 1981

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

By A. V. Corlett

THE use of the diamond-drill hole as a means of breaking clown ore and waste is not new. Years ago, the method was adopted in mines in northern Ontario and in the western United States to reach out to bad pillars, or to remnants of ore left on walls, the winning of which by any other method might be dangerous or too expensive. The practice is still in vogue and has generally proved a success. Of the known mineral deposits in Canada and elsewhere, many are of very low grade. Some are marginal and not even worthy of being classed as 'ore' until some means is found and proved of exploiting them economically. Other conditions being favourable, if a mining method could be found that would give a large 'bulk break' with a sufficiently low cost of development and a low cast of mining per ton, mineral deposits of this latter type might be brought into the classification of ore. We know that any block-craving system whereby the ore may be undercut and allowed to crush and cave will give a very high breakage and low costs. In some cases, however, the physical characteristics of the ore do not lend themselves to this method. In such ore-bodies, the alternative system of 'bulk-breaking' might be aided by long diamond-drill blast holes. We could obtain this 'bulk breaking' by the use of long diamond-drill holes in conjunction with a sub-level system using extremely thick benches, or possibly by the adaption of modified open-pit methods to underground mining. ln fact, if conditions are favourable, the idea would be simply ta open up a slot or free face and break into it on a larger scale with longer holes. The use of deeper benches-that is, using each level as a sub-level and thereby eliminating much development footage, slashing, setting up, and mucking time-would naturally be expected to lead to cheaper mining.

Jan 1, 1940

By Stephen C. Tadolini

The U.S. Bureau of Mines conducted a laboratory investigation designed to evaluate the stress and deformation characteristics of fully grouted roof bolts subjected to various magnitudes of end loadings. The experiment and subsequent analysis were completed, utilizing axial deformation data obtained -ultrasonically from forty-one 4-ft, grade 40 roof bolts, with a total of 132 measurement locations along the lengths of the bolts. The ultrasonic measurement instrumentation used in this investigation allowed for elongation measurements without requiring extensive bolt modifications. The results indicate that approximately 39 pct o{ the applied end load dissipated within the first 3.4 in of the bolts. However, only 3 pct of the applied load was realized beyond 28 in of the grout column. Data are presented individually for every 6-in increment of bolt length, and analysis was performed using statistical, nonlinear equations developed for 5,000 and 8,000 lb loading conditions.

Jan 1, 1990

By R R. Lovel, G J. Sparrow

Currently there are large reserves of good quality iron ore near to existing infrastructure that are not being developed because the phosphorous levels are above acceptable market specifications. Since the high phosphorous content is considered to be mainly associated with the goethite fractions of the ore, attempts were made to leach the phosphorous from the ore after a heat treatment to dehydroxylate the goethite. Heating the ore and leaching with 40 g/L NaOH lowered the phosphorous levels from 0.145 wt per cent P to 0.075 wt per cent P or lower, but a heating temperature over 800¦C was required to achieve this reduction in phosphorous levels. However, when sodium hydroxide was added to the iron ore before the heat treatment, similar phosphorous removal was achieved with a heating temperature of 300 - 350¦C. It was considered that dehydroxylation of the goethite in the presence of the hydroxide makes the phosphorous available for removal with a water leach. As well, 50 per cent of the silica and 60 per cent of the alumina in the ore were also removed in the leach, but some sodium remained in the leach product. Further work is required to remove the residual sodium to produce a marketable product.

Jan 1, 2009

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By R. J. Sheets

"What is the primary responsibility of geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer — ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geoengineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this article will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face.What is our purpose?A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question “What is our purpose?” I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor ground water levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: Safety. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or ground water."

Jan 9, 2018

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968

By I T. Ross

In the last 50 years there have been tremendous improvements in equipment used in development on underground mines. Compressed air powered jacklegs have been replaced by high powered electro-hydraulic drifters on sophisticated drill jumbos and load haul dump units have taken over from small shovels and rail cars.Despite the increase in power applied in key parts of the development cycle, average advance rates have fallen and costs have increased. The factor that is most often regarded as the main contributor to slowing advance rates is increased support requirements. Whilst there is no denying that the drive to improve safety has resulted in the requirement for more bolting and the installation of a skin support (mesh or shotcrete), this is not the only factor.Within the industry as a whole, many of the basic principles of development appear to have been lost over time. This paper looks at a historical case study and discusses some of the features of old development cycles that are no longer in use. This highlights some of the basics that appear to have been forgotten. These may be indicators to what may provide improvements in the conventional drill and blast development cycle.CITATION:Ross, I T, 2014. Development – back to basics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 67–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Mark S. Sanders

Based on laboratory tests and preliminary field tests of off-the-shelf steel toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners' boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A five month field evaluation compared the prototype boots to the boots the participants usually wear. Although objective slip and fall data showed no significant advantage for the prototype, subjective evaluations made by the participants indicated increased traction for the prototype boots. Approximately 75 percent preferred the prototype to their own boot. Approximately one-third used the lace-up capability. It was concluded that molded soles provide better traction than calendared soles for the underground mining environment.

Jan 1, 1982

By Guocheng Pan

"Although many factors play roles in the estimation of recoverable reserves, smoothing effect and conditional bias are considered major geostatistical issues in the estimation. This paper introduces measures for smoothing effect and conditional bias, and provides insights into their relation to the estimation of recoverable reserves. Both smoothing effect and conditional bias are intrinsic to the information effect and kriging estimators. For a given level of drilling information, however, it is possible to identify the optimal search radius that minimizes conditional bias. Furthermore, it is also feasible to define variance correction factor for reduction of the smoothing effect from exploration block models. Both of these components are key to the accurate estimation of recoverable reserves. IntroductionThe accurate estimation of recoverable reserves is critical to decision making in different phases of feasibility study and mine planning. Much attention for improving the methodology of estimation has been focussed on the effect of the change-of-support (Parker, 1980; Dagdelen, 1996). For example, it is essential to make a volume- variance correction to the estimate of multiple indicator kriging (Hoerger, 1992). When the size of block, b, in the geostatistical model differs from that of selective mining unit (SMU), v, a volume-variance correction is warranted for the prediction of recoverable reserves.Most mining plans and decisions are made prior to the availability of high density blast-hole samples. In most mining operations, the true SMU grade Zv is unknown at the time of selection. Instead, the selection is based on the estimate Z v**derived from high density blast-hole samples within the deposit G. Nevertheless, the estimate Z v * of recoverable reserves in the stage of mine planning is derived from exploration data. At the end, the production result must be reconciled to the estimate Z v * . In other words, the selection is based on Z v** from blast-hole samples, while the final production figures are reconciled to Z v * from exploration drilling. For a given preselected cutoff grade z0, the actual mining panels will consist of the units having the estimated grade Z v** =z0 rather than the true grade Zv =z0. The difference between Z v** and Zv is usually of less concern."

Jan 1, 1998

By S. C. Termes

The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly dissem-inated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. postflocculation separations resulted in flocculated bornite in grades as high as 92 pet. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s).

Jan 1, 1983

By J Tibbett, A Colebourn, B Hebblewhite, F Suorineni

The concept of Big Data refers to data sets that are so large, variable and/or complex that traditional data processing applications struggle to integrate the data for effective investigation, analysis and value generation. With advances in sensor technology and smarter equipment, the mining industry is experiencing Big Data, and in a different way to how the intelligence and marketing communities experience Big Data. Future mining will bring larger, more complicated and diverse data sets increasing the strain on traditional data integration and investigation techniques. Block caving is an important mining method for the extraction of massive, low-grade ore deposits due to its low operating cost and high production potential, given the right orebody geometry and ground conditions. This paper focuses on block caving due to its increasing popularity and importance in the future economic extraction of multiple commodities. The block cave mining system (BCMS) is a complex interrelation of factors, and due to the reliance on natural processes within the system, it is one of the least understood mining methods. Obtaining information on the factors within the BCMS generates large, complex data sets on various time scales. Each sensor network within the BCMS combines spatial and temporal information with tens to hundreds of recorded parameters. Data sets are quickly moving from multidimensional to n-dimensional. Optimisation of the BCMS is only possible through a holistic analysis approach, thus involving the integration of multiple, diverse, n-dimensional data sets (Big Data). This paper presents a current example BCMS Big Data situation involving 12 sources of information with differences in volume, data format and frequency of data generation. This suitability of virtual reality scientific visualisation (VRSV) as a solution to BCMS Big Data interpretation difficulties is then discussed. These 12 data sets can be effectively integrated using VRSV for intuitive and accelerated investigation of the BCMS. Potential future Big Data within the BCMS is presented involving 20 sources of information resulting from our increased need for monitoring and advancements in technology. Current methods of defining queries may not be suitable within these future complex, multidimensional data sets, and the potential of artificial intelligence algorithms within this system is discussed. These advancements in technology and machine learning lead to the requirement of live data acquisition and analysis. VRSV is identified as a suitable technology to satisfy the needs of real-time insight into the performance of these future caves for optimised management and reduced risk.CITATION:Tibbett, J, Suorineni, F, Hebblewhite, B and Colebourn, A, 2015. Virtual reality scientific visualisation – a solution for big data analysis of the block cave mining system, in Proceedings Third International Future Mining Conference, pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015