Search Documents

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By M. S. Badollet

"The study of the physical properties of asbestos minerals requires a careful isolation of the fiber from the wall rock and, at a later stage, a comparison of these physical properties with those of fibers that have passed through the milling and beneficiation processes.The effects of mineral impurities, loss of fiber length and the formation of extreme fines (asbestic and/or associated minerals) often show up in the formation of special asbestos products as well as in the commercial production of asbestos papers, mill-boards, asbestos cement products, plastics and insulation materials, and in the filtration of blood plasma and wines.Numerous test methods have been developed in Canada and in England for use in the asbestos industry. Special treatments of asbestos fibers have been used to improve their physical and chemical properties and to eliminate impurities.Numerous problems connected with the use of asbestos fibers are discussed, such as the effects of asbestos on filtration, surface area, surface treatments using organic or inorganic materials, the surface charge on the fiber, the presence of magnetite and air pollution elimination. Biological studies on finely ground asbestos, when dispersed in 0.9 per cent sodium chloride solution and then sterilized and injected into hamsters, show that by reducing the dose, the tissue damage can be largely avoided. In these experiments, Arizona asbestos fibers were carefully extracted from the wall rock, finely ground, and examined chemically and micros-copically for any mineral impurities that might be present so that any effect on the hamsters would be directly due to the presence of the asbestos. The harsh Arizona fiber induced more extensive tissue response than the soft fiber when tested in hamsters."

Jan 1, 1969

By Oliver C. Ralston

The growing popularity of perlite (sometimes spelled pearlite) as a raw material for thermal expansion into pumicelike products in the Western States has prompted a preliminary investigation of the properties of such material and the problems that want solution to put a perlite industry on a firm foundation. The Bureau of Mines is undertaking the gathering of data and the solution of these problems, and the following paper records some of the available information. and the promise of the material, with some comparisons of advantages of the various competing lightweight aggregates that can be made from siliceous volcanic glasses and rocks containing entrapped or dissolved water that causes their expansion on' quick heating to their softening points. This new industrial rock has caught the fancy of the mineral industry in the western States because it has Fume advantages over natural pumice. Chemically, it is typified as rhyolitic in composition, and one may find obsidian, rhyolite, pumice, pumicite, and perlite from the same vant and contemporaneous in origin. The material need not be rhyolite but should be a siliceous or acid lava and contain 2 to 5 percent water still in "solution" in the rock. On quick heating to the softening temperature the material puffs, due to conversion of the contained eater into bubbles of steam. Slow heating causes gradual release of the imprisoned water by decrepitation and. cracking and-results in, very little puffing. Perlite is often in the form of ovoid volcanic bombs formed by explosive eruption of large masses of lava into the air, where they, quickly cool, with escape of little of the contained water, exceptt perhaps for a hollow interior. Since they cool in layers they have an onion-type structure and a pearly luster from interference of light between the. layers, which is' the origin of the name "perlite." Perlite may occur in intruded flows that have been quickly cooled and partly expanded but retained most of their magmatic water content. Obsidian may be the same lava cooled quickly under conditions that prevented crystallization of feldspars and other minerals, leaving the volcanic glass that may or may not retain all of the original contained water.

Jan 1, 1946

By M. S. Diederichs, G. Walton

"Developments in understanding the brittle fracture of rock over the past two decades ultimately led to the acceptance of a cohesion-weakening-friction-strengthening model as an appropriate strategy for the modelling of spalling using a continuum approach. This strength model has been used to replicate observed failure depths and geometries for a number of case studies in the literature, most notably the AECL Underground Research Laboratory in Manitoba. One thing which these case studies typically ignore, however, is the influence of rock dilatancy on the evolution of brittle failure. Physically, this phenomenon is the volumetric expansion of the rock due to fracture opening; numerically, this phenomenon is captured by the flow rule, which is often characterized by the dilation angle, ?. Accurately modelling rock dilatancy in conjunction with strength evolution is necessary both to predict the magnitude and distribution of ground displacements, as well as the exact depth and shape of the fracturing zone. Both of these factors can have significant implications for support design. This paper is focussed on presenting some of the recent developments in this field in the context of a number of numerical modelling case studies. Initially, a new model for the dilatancy of brittle rock is presented, as well as some representative data and model parameters for different rock types. Next, several case studies of highly stressed tunnels and shafts are presented. The results of continuum numerical models are presented to demonstrate the ability of the back analyses to match observed in-situ measurements and obtained. The predictive capabilities of the material model are also highlighted for cases where sufficient “a priori” information (such as laboratory compression testing data) are available. The issues of model nonuniqueness and strain-localization/bifurcation are also addressed."

Jan 1, 2015

By C. H. Stockwell

RICE LAKE-BERESFORD LAKE area, situated 100 miles northeast of Winnipeg (Figure 1), is Manitoba's foremost gold mining district, although it is exceeded in gold production in the Province by the Flin Flon base-metal mining district. At present, the area is producing at the rate of about one and three-quarter million dollars annually, almost entirely from the San Antonio and Gunnar mines. The total production to date is about $14,000,000. Of this total, over $7,000,000 has come from the San Antonio mine, over $2,000,000 from the Gunnar mine, about $4,000,000 from the Central Manitoba mine, and the balance from several smaller properties. The writer has led Geological Survey parties in the area for the past four summers. The present paper gives a summary of the results of this work and also includes the findings of C. S. Lord, who was in charge of a party for one year. Much valuable information was obtained from earlier published reports on the area and from officials of mining companies, to whom the writer is indebted for their kindly co-operation. It is impossible in this short paper to give proper credit to the earlier workers or to discuss certain points o disagreement between their conclusions and those presented here. For further information the following references may be consulted.

Jan 1, 1940

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986

By E. Spencer

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose over the Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. The software relies on a time-motion study that profiles the worker?s daily activities. Observations about the worker?s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks, so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the Action Level or the NIOSH Recommended Exposure Limit. The software generates a variety of interactive onscreen displays showing where, when, and how the worker?s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations, and times that are associated with the greatest amount of the worker?s noise exposure. DOSES simplifies the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise over-exposure of their workers.

Jan 1, 2010

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, P. Ghobadi

Design and selection of equipment for a grinding circuit strongly depends on the mill function, ore properties and requirements of the down-stream circuit. Primary mills usually work in open circuit and size distribution of product would be controlled in the final steps using a classifier like cyclone. Although HPGRs are mostly utilized as pre-grinding mills, it is preferred to utilize them in a closed circuit due to their specific mechanism of comminution. Unique mechanical design of HPGR and its completely different crushing process than tumbling mills needs precise consideration on its circuit design. In this paper, we investigate the impact of different parameters on design of pre-grinding HPGR circuit and selection of the proper classifier. Our study focuses on iron ore properties (e.g. moisture, particle size distribution of feed and product, compatibility and de-agglomerability). We also investigated various options of HPGR circuit according the classifier efficiency and influences on down-stream processes. The optimum operating parameters of HPGR (working pressure, speed and level of hopper) for the selected circuit were also determined based on pilot and industrial data. Our pilot and industrial tests and observations revealed that HPGR should be arranged in closed circuit because of the edge effect, as a negative factor of non-uniform distribution of pressure force along the roller width and presence of non-crushed particles in the mill product. Wet vibratory screen could be the optimum option for screening of its discharge. Fine part of the wet screen discharge could be delivered to the concentration stage without over-grinding in ball mill using a hydrocyclone working in a reverse closed circuit mode. Moreover, our pilot and industrial tests during design and operation of ten HPGRs in various iron ore processing plants proved that higher pressure and lower roller speed in a fixed level of material inside the hopper could give the desired product size distribution.

Jan 1, 2016

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Jan 1, 1949

By M. Jayaraman

With the ever increasing demand for commodities, due to changes in lifestyle and increase in population, people are striving to find ways to keep up. Mining is one essential element in the solution. Though being a powerful boost to a country?s economy, mining can have disastrous effects in the absence of waste management practice and technologies; because of the harmful heavy metals and toxic chemical waste that is generated as a by-product in mining operations. It is an established and documented fact that pollution is a major concern for communities having to live with it. Disproportionate water consumption significantly impacts local rivers and ponds thereby reducing freshwater availability and have given rise to social conflict. In light of these misgivings, management and treatment of mine water and waste has gained considerable attention recently. In this paper, we summarize some of the treatment methods that can be adopted by mining companies to reduce their environmental footprint. Appropriate treatment solutions depend on various factors including available space and capital cost for treatment solutions, type of mining waste generated, current state of the mining plant, geographical location, and other location specific issues. Incorporating waste and water management solutions as a priority within mining operations is critical for addressing increasing regulatory requirements and a starting point for initiating other Corporate Social Responsibility (CSR) programs. Collaboration among mining companies, NGOs, local community, and government facilitates successful projects which build trust leading to long term relationships. In this paper we also talk about the benefits of implementing a CSR project that captures the focus of local communities and allows the mining company to focus on operations. Implementing a sustainable business model that incorporates the broader community impacted by projects will continue to benefit even after the mining company ceases operation in that location. The challenges involved with implementing effective CSR projects, which require measuring and reporting effectiveness to create a positive social, economic, and environmental impact is also presented in this paper.

Aug 1, 2013

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant?s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today?s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user?s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project?s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By W. E. Selnes

Introduction In 1938, a survey conducted by the Ontario Mining Association revealed a rather startling fact. Injuries incurred in chute pulling were more numerous than those from any other single cause. This report prompted Mr. W. B. Paton, then Inspector of Mines for Manitoba, to make a similar survey of the mines of his Province. It indicated that, in Manitoba mines, chute accidents ranked second only to those from falls off roofs and sides. Why has the mining industry been so slow to recognize the dangers of chute pulling? A partial answer may be the lack of any systematic classification of accidents according to their real cause. The result has been to attribute to other causes injuries which were a direct outcome of chute pulling, and, indeed, has made it difficult to analyze accidents in the industry as a whole. Perhaps, too, because chutes are generally located in the comparative safety? of the drifts, there has been a tendency to consider the occupation as not very hazardous. Not until enough statistics were obtained on this particular task could it be appraised correctly. The Mining Association's survey has been most helpful, and latterly the industry has done a great deal toward analyzing the causes of chute accidents and toward determining an effective means of overcoming them. Much, however, remains to be done. An effort will be made in this paper to outline methods which have been found successful in materially reducing the number of injuries. Qualifications of the Chute Puller First of all it must be realized that chute-pulling is a specialized occupation. The men require proper training for the job, just as in other mining operations. Care must, therefore, be taken to choose persons whose qualifications fit them for the job. Chute-pulling is an integral part of the general mining operation and cannot be considered as isolated from the tasks of other workers. One of the essential qualifications of a chute-puller is a sufficient knowledge of mining operations to appreciate the effect his work will have on the safety of others in the vicinity. He must take the necessary precautions, by verbal warnings, by placing barricades and signs, or by personally guarding the chutes, to prevent accidents to fellow workers.

Jan 1, 1947

By R. R. Wells, K. C. Vincent, A. O. Ipsen

"INTRODUCTION The Philipsburg Mining District, Granite County, Mont., has been the largest producing area for battery-grade manganese (70 percent MnO2) in the United States since the First World War. Two companies, the Trout Mining Division of the American. Machine & Meals Co., and the Moorlight Mining Co., have intermittently mined and milled 120 to 250 tons of 25-percent manganese ore per day for the production of concentrates of this grade.Investigation of the district by engineers of the Federal Geological Survey and Bureau of Mines indicated that further exploration and develop¬ment would make available additional oxide and carbonate manganese ores for milling and production of metallurgical-grade manganese. If the battery-grade producers converted their plants to the production of metallurgical-grade concentrates, their production also could be increased through greater recoveries.Until February 1, 1944, the Metals Reserve Company, through its agent, the Sunshine Mining Co., purchased milling-grade manganese oxide and carbonate are for stock-piling at Philipsburg. After that time, only carbonate ore was purchased. Based upon the assumption that the stock pile was a true cross-section sample of the producing area, metallurgical studies were made on representative samples from the Metals Reserve stock piles. Testing also was conducted on two other samples of Philipsburg oxide manganese ore obtained by engineers of the Bureau of Mines from the Little Dandy claim of the Donlan group and from the Marie mine. All ore samples tested were found to be amenable to concentration by ore-dressing methods for the production of concentrates that when sintered met Metals Reserve Company specifications for metallurgical-grade manganese."

Nov 1, 1947

By Paula Ana Paiva

The high economic value and unique technological properties of the platinum-group metals (PGMs), plus their growing scarcity in the Earth’s crust, justify the crucial importance of developing recycling practices for PGMs end-of-life materials. Examples of top devices relying on the use of PGMs are automotive and industrial catalysts, and electrical and electronics equipment. This article critically describes the most recent research on the use of solvent extraction to recover one PGM, palladium, from spent catalysts. Some groups focus on the development of schemes involving commercial extractants, while others prefer to design specific molecules to efficiently and selectively recover palladium from these particular complex leaching solutions. Examples of commercial extractants proposed for the former schemes are Alamine® 308, TBP and LIX® 84I; while on the other hand, sulfur-containing diamides, thioamides, thiocarbamates, and dithioethers have recently been developed. Ionic liquids have to be mentioned too.

By Phillip I. Merritt

"IntroductionDuring and since• the war, it has been my privilege to work closely with those in Canada who are responsible for the vital raw materials needed in our co-operative atomic energy programme. The understanding which has developed between our two groups in this all-important enterprise has been a great source of pleasure. We in the United States are aware of the importance of the contribution made by Canada to this project, and we look forward to continuing our mutually advantageous relationship.The impact of World War II, and the decision by Canada, Great Britain, and the United States to join in a programme for the development of atomic weapons, created a sudden and immense demand for uranium minerals. Early in the raw materials programme, it was evident that sufficient raw materials to fulfill war-time atomic weapon requirements could be secured from three sources: the rich pitchblende deposits of the Eldorado , mine at Great Bear lake; the Shinkolobwe mine in the Belgian Congo; and as a by-product of the vanadium industry of the Colorado Plateau in the United States. In the early part of the programme, therefore, our joint efforts were directed toward obtaining immediate maximum production from these localities. The contribution made by Eldorado Mining and Refining (1944), Limited, both in supplying and refining raw materials, was and continues to be of vital importance.In addition, it was also obvious from the first that in this programme, as in any mining enterprise, exploration activities directed•toward the discovery and development of new sources of uranium ore were essential if production were to be maintained over an extended period of time. In order to satisfy obvious security requirements during the war, it was necessary to proceed with this exploration programme, both in Canada and the United States, as secretly as possible. With the end of the war, and the revelation that an atomic weapon had been developed, however, secrecy in exploration was no longer required. The important thing was to get on with a broadened exploration programme."

Jan 1, 1950

By D. E. Cameron

"INTRODUCTION Grade control requirements for base and precious metal projects are an important input to both conceptual and feasibility mine plans. It’s the author’s experience that grade control input is insufficient at these critical stages. The few exceptions are a stimulus for this paper. A significant portion of CRC’s practice has involved assisting operations to solve grade control issues which were finally recognized as contributing to negative production variances. Even in operations perceived to be successful, deficiencies in grade control are often masked by measures taken by an operation to compensate a deficiency in one area with outperformance in another. The advantages in having a realistic and adequate grade control plan developed at an early project stage by a geologist(s) with considerable operations experience are manifold. It’s important for the geologist to prepare clear inputs into the mine plan backed by detailed supporting information in usable, flexible formats. When the decision is made to advance a project, the exploration team passes its model to a mine planner. The team doesn’t usually provide a detailed grade control plan with the block model, thus the planner tends to treat grade control as an activity to be rolled into a broader operating category. The consequences of highly compartmentalized mine planning can be severe in the long run. Once a plan is tabled, and especially once production begins, it is very difficult to improve grade control outside the fixed parameters of the operation. Major fixes tend to be costly in terms of time and dollars. Implementing needed changes to the grade control practices and culture in an established mine can present almost insurmountable difficulties. Hypothetical examples of grade control planning are presented to illustrate the author’s points. The diagrams are conceptual and schematic; any resemblance to actual deposits is coincidental. BEYOND 50¢/TON In more than a few cases, grade control cost is buried in a subcategory of mining cost with little more consideration than a plugged number. It is possible to do a word search in 43-101 Technical Reports on advanced projects and without finding reference to “ore control” or “grade control”. The idea is to reach the orebody by the shortest and least expensive means, achieving production and investor payback at the earliest possible occasion. This entails a low stripping ratio pit or a decline ramp with sills on ore to prepare the first stopes. The processes to achieve the target production, one of which is grade control, will fit into this framework. After all, there is a block model and the planner can see the grade and tons in each block. The exploration geologist whose responsibility was to bring a large percentage of the deposit into mineral resource owns the model and has released it to planning. Now comes the planning stage. Mine geologists haven’t been hired yet and they will be phased in with production. What could go wrong? Larger companies may have the geologists with operating depth who will be inserted into the mine planning discussions, but it’s not a given. Junior companies must often delegate the conceptual and detailed planning tasks to consultant groups. Is a senior-level grade control review part of the scope of work for the mine planning? If a good grade control plan is in place before the mine geology team is staffed, a key element of success is assured."

Jan 1, 2018

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By G. Issid, J. McGinty, C. Lee, Y. Pepin

For more than a decade, Hatch has used process and logistics models to assist Rio Tinto Fer et Titane (RTFT) with capacity planning, debottlenecking, and optimization to help ensure design capability, capital effectiveness, and operational efficiency of the integrated production chain. Process models are used to optimize the physics-based aspects of the system, such as mass and energy balances, flow rates, yields, and equipment specifications. Dynamic logistics models are used to optimize how the various plant areas work together to achieve the desired ends and deal with such things as plant scheduling and synchronization strategies, sizing of buffers between processes, defining the required number of process and material handling units, and designing a plant layout that minimizes plant interferences and inefficiencies. The combined use of process models and logistics models enables the overall plant to be optimized from both a productivity and quality point of view, with each plant area working in harmony with one another to achieve targeted capacities and efficiencies. This paper describes the many benefits derived from such modeling efforts over the past 15 years for each of the major plant areas at RTFT: Beneficiation Plant, Smelter Plant, Steel Plant, UGS Plant, and Powder Plant (RTMP).

Jan 1, 2011

By Anoop Sattineni

Over the past decade the use of BIM in the AEC industry has grown several fold and with it the number of standards available for implementing BIM. The ?National BIM Standard? by buildSmart Alliance, the ?Contractor Guide to BIM? by the Associated General Contractors of America, the ?BIM Project Execution Planning Guide and Templates? from Penn State University, the ?BIM Roadmap? by the US Army Corps of Engineers are some of the several BIM guidelines that are currently available to the AEC industry practitioners. Some of these guidelines are as comprehensive as defining BIM and the associated taxonomy while others are meant to be used on an individual project basis. From a contractor?s perspective one of the key benefits of using BIM is for the purpose of collision detection and coordination. This research has found that currently available guidelines do not address these issues adequately. For instance, the currently available guidelines do not allow the subcontractor to quickly communicate issues such as naming conventions and color schemes within the model, to the general contractor. Consequently general contractors and sub-contractors find themselves making changes to their BIM deliverables based on each other?s abilities and levels of adoption, apart from reason?s stemming from use of different software platforms. This paper describes how a group of contractors and subcontractors from Atlanta and Birmingham in the United States came together to create and adopt a ?Coordination Guidelines for Virtual Design and Construction?. These guidelines were specifically created with the purpose of streamlining the construction coordination process using BIM. This paper describes how the guidelines created differ from other guidelines currently available in the industry.

Aug 1, 2013

By J McCluskey, N Barros

"Long-term strategic planning at BHP Billiton’s Western Australia Iron Ore business aims for sustainable value maximisation of its large, long-life, low-cost, expandable mineral inventory and supply chain infrastructure. While mine plans are key components of this value equation, this objective requires a whole-of-business approach through comprehensive consideration and optimisation of the full value chain. Only through a system view do we believe that the value proposition of a set of plans is truly optimised.The fundamental considerations include: mineral inventory information, given its intrinsic uncertainty and risk/knowledge horizon a marketing view of future quality premium/discount based on overall market quality load whole of supply chain optimisation on a throughput accounting basis alternative sequences of capital decisions closure costs with significant magnitude of total movement requiring optimisation as part of the plan. In addition, the plan provides a view of acceptable uncertainty levels at different times in the future.BHP Billiton Iron Ore uses a structured Life of Asset planning process that supports the business with the optimisation of its maximum value proposition through a non-deterministic scenario-based optimisation approach on an annual basis. This is a key input to each year’s medium-term plans and budgets, including activities identified through a value of information approach that resolve the key uncertainties and steadily improve confidence in the plan.CITATION:McCluskey, J and Barros, N, 2014. Life of asset planning, uncertainty and value optimisation of the iron ore business – from exploration, to market, to closure, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014