Search Documents

By N. A. Gokcen

In this Bureau of Mines report, appropriate equations correlating the activity of water with the activities of electrolytes in binary and multicomponent solutions have been derived for computer calculation. It was found that the half-integer power series are far superior to the integer power series, for both types of series having the same number of terms. The pro-posed method of calculation is capable of accurately yielding the activities of all components from the measurements of the activity of a single component at various concentrations. This method replaces the cumbersome and objection-able method of graphical integration of the Gibbs-Duhem equation. Two novel methods are proposed for determination of activities of electrolyte solutions important in hydrometallurgy; (1) Water vapor pressure measurement by differential pressure transducers having an accuracy of 0.001 pet, and (2) transpiration method with an inert gas bubbled through concentrated solutions followed by the analysis of the evaporated and redissolved electrolytes with specific ion electrodes having a sensitivity of ±10-10 molal. The first method is suitable for nonvolatile electrolytes, and the second, for volatile electrolytes such as hydrogen halides, HN03, H2S03, etc. The existing methods of estimation of ionic activities have been surveyed, and the best method has been selected, discussed, and summarized.

Jan 1, 1979

By V. B. Dale

This paper is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits of New Mexico. Most of the descriptions are from field examinations by the senior author. Reported tungsten occurrences that were not visited are listed below: Colfax County: Occurrences of ferberite in thin veins in Willow Creek near Elizabethtown.4/ Dona Ana County: Small, low-grade occurrences of scheelite near the summit of the Organ Mountains about 15 miles east of Las Cruces. Hidalgo County: Scheelite reported in the Daisy mine 7 miles southeast of Hachita. Ores are carbonates containing copper, gold, silver, and bismuth.5/

Jan 1, 1959

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars in early 1980 for the purpose of disseminating recent advances in mining technology related to surface coal mining reclamation.

Jan 1, 1980

By Herman W. Hill

This report summarizes research into the root causes of failures in mine power systems which impact safety and reliability. Abnormally low fault currents, due to arcing faults, self-excited systems, and fallen trolley wires are examined and quantified. The reliability of components which are critical for safety is studied, as well as reliability of components which are crucial to the mining pro cess. Failure rates are found through in-situ tests, accelerated life tests, studies of mine maintenance, and fault-tree analysis. Reliability data is used to predict fatalities and lost-time accidents through computer-aided fault-tree analysis. Analytical support tasks reported include the deriving of trailing-cable ampacities under cyclic loading, and the measurement of connected ground beds.

Jan 1, 1981

By C. Arthur Carlson

"It now becomes my privilege and duty to call to order this fifty-first meeting of the Rocky Mountain Coal Mining Institute. "I bid you a hearty welcome and I know by your attendance at these meetings you will gain a great deal of valuable information, as well as have a wonderful time. "We have been very ably represented by Mr. John H. Emrick as General Chairman, assisted by our good friend Mr. Fred W. Whiteside, our secretary and treasurer. I know they have worked very hard in selecting the various committees, who in turn - by the looks of our program have gone all out to prepare material that should be of great interest to us. I trust we will be attentive to the subjects presented and freely enter into the discussions, also relating our problems and experiences. I am sure this will prove both profitable and beneficial to all present. "The main purpose of these conventions is to become acquainted with each other, renew old acquaintances, talk over our problems, and have a little fun and relaxation from our every day routine. "Let us not forget the manufacturers, the distributors, the operators, or the press because it is through their splendid support that this organization is successful. "Since our last meeting we have gained many new members, whom we especially welcome. We are sorry to have lost a few. I am mindful, at this time, of two very good members from my home state who have passed away, Walter Wetzel, a former president of this institute, and Lee Alger, at the time of his death, Vice-President from Utah. We also lost very recently our assistant Secretary-Treasurer, Everret Davis. These men contributed a great deal to the institute and the coal industry in general. I am sure they are greatly missed by all who knew them."

Jan 1, 1955

By Joseph B. Story, John T. Clarke

A modification, of the Kelvin bridge using an inductor was used to measure the conductivities of molten sodium chloride, calcium chloride, and mixtures thereof. A capillary-type four-lead fused quartz dipping cell was constructed. The effect of a small amount of potassium chloride on the conductivity of the melt was determined. IN the electrowinning of sodium and chlorine from sodium chloride in Downs cells, calcium chloride is added to the sodium chloride in an approximately equimolar amount to permit cell operation at a lower temperature. This lower temperature improves current efficiency and ease of operation, but decreases voltage efficiency by decreasing the electrical conductivity of the melt. A knowledge of the electrical conductivity of the Downs cell melt is necessary to the understanding of Downs cell operation, for the IR voltage drop across the melt is responsible for a significant part of the electrical power consumed by the cell. The work of previous investigators on fused sodium chloride-calcium chloride mixtures was reviewed from the standpoint of consistency with the results of others on the conductivities of the pure constituents. The electrical conductivity of pure fused sodium chloride has been established with accuracy by Van Artsdalen and Yaffe,1 by Edwards, Taylor, Russell, and Maranville,2 and by Lee and Pearson.3 It has also been studied by a number of other investigators.4-13 The best values for calcium chloride are believed to be those of Lee and Pearson,3 since the sodium chloride and potassium chloride conductivity values given by them check the best literature values. A number of other investigators have also reported values for calcium chloride.'-"."' Electrical conductivity data for fused sodium chloride-calcium chloride mixtures have been reported by Sandonnini,12 Vereshchetina and Luz-hnaya,18 Ryschkewitsch,11 Barzakovskii,5 and Alaby-shev and Kulakovskaya.15 Sandonnini reports no data at temperatures lower than 850°C. The conductivity values reported by Vereshchetina and Luz-hnaya, by Ryschkewitsch, and by Barzakovskii for pure sodium chloride and for pure calcium chlor- ide vary somewhat from the literature values believed to be best and the sodium chloride-calcium mixture data of these authors and of Alabyshev and Kulakovskaya (who give no data for the pure compounds) show significant variations. In view of these facts, it seemed that an investigation of the electrical conductivities of fused sodium chloride-calcium mixtures would be worthwhile. Apparatus Bridge System—The bridge used,in this investigation is diagrammed in Fig. 1. In general, the elaborations of this bridge over the simple Wheatstone bridge were for the purposes of a) eliminating lead resistances or making them accurately measurable, and b) eliminating major capacitative and inductive effects or balancing them against each other. Lead resistances in the lower arms of the bridge were kept as low as possible by making the leads short and of low resistance wire. This could not be done in the cell arm of the bridge because of the remoteness of the cell from the other bridge components and because of the high-resistance nickel or chrome1 wires used in the cell. Since maximum sensitivity is attained when the resistances of the four arms of the bridge are equal, 50-O resistors were used in the lower arms of the bridge when fused salt conductivities were being measured, and 1000-O resistors were used when the cell was being calibrated with normal aqueous KCl solution. The cell resistance was of the order of 50 ohms with fused salts and of the order of 1000 ohms with normal aqueous KC1 solution. The resistors used were non-inductive and accurate to 50.05 pct (General Radio Co. Types 500-C and 500-H). The lead resistance between point A in the cell and point E at the measuring resistor was eliminated by using the kelvin bridge principle; that is, the voltape drop across the lead from point A to point E was divided between the cell arm of the bridge and the measuring arm of the bridge in proporation to the resistaxes in the lower arms of the bridge.

Jan 1, 1958

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By C. G. McLachlan

Abstract This paper deals with the application of the cyanide process to recover gold from a pyrite concentrate produced by means of differential flotation. This concentrate before cyanidation contains from 0.09 oz. to 0.14 oz. gold per ton, of which only about 60 per cent is recoverable. The rest is so fine that it remains interlocked in the pyrite and therefore is not acted on by the cyanide. The concentrate also contains about 15 per cent pyrrhotite and 0.4 per cent chalcopyrite, both of which are cyanicides. The cyanicidal effect of the pyrrhotite is inhibited by preacracing the pulp with lime, and maintaining a high lime alkalinity during cyanidation. The effect of the chalcopyrice is reduced as far as possible by removing those particles which are free by means of a further flotation step immediately prior to cyanidation. This involves the flotation of some very fine material. After nullifying as far as possible these two cyanicides, the concentrate is cyanided directly, i.e., without being roasted. This leaves the pyrite available for subsequent sale as a source of sulphur dioxide and sulphuric acid, and the entire residue of the cyamde plant, amounting to about 500 tons per day, 1s now being disposed of in this way. Prior to deciding on direct cyanidation, a number of laboratory roasting tests were made. These showed chat, 1f proper control were exercised, a better recovery of gold could be effected from the roasted product than by the direct method of treatment. The tests also showed that the capital cost o the plant would be much higher than that needed for the procedure adopted. The possibility of subsequently selling the pyrite for its sulphur content would also have been eliminated. Introduction A previous paper has described in considerable detail the application of the flotation process to improve gold recovery from Noranda's milling ore, and in so doing has covered the production of an auriferous pyrite concentrate. The present paper deals with the recovery of gold by cyanidation from that concentrate. This gold, though intimately associated with the pyrite, can, for metallurgical purposes, be considered as all occuring in the native state.

Jan 1, 1946

This report discusses the nonfuel critical minerals position of the United States-both current and future (to the year 2000). We have assumed that there will be no major global disturbances-military, political, or economic-during the rest of this century. However, international relationships, strategies, and conditions that affect the supply of minerals are very tenuous, normal trading patterns can be easily upset, and national and ideological objectives can and do interfere with "normal" free market conditions. For example, the Department of Defense has reported that the Soviet Union is engaged in a strategy designed to reduce the availability of strategic minerals, through either physical disruption, market manipulation, or domination of producing or neighboring states. Although such a strategy poses serious concerns for the United States and the free world, the impacts of disruptions are not covered in this publication. Historical Perspective The modern industrial economy of the United States is founded on the production and use of minerals.* Two hundred years ago our forebears began taming a raw continent, developing a base for agriculture and a rudimentary minerals producing system. In the 19th century, with the aid of imported labor and capital, the development of America's vast natural resources was undertaken, and the transition from an agricultural to industrial society was underway. By the century's close, the United States had emerged as a great industrial power, partly through the development of such mineral resources as iron in Minnesota and coal in Pennsylvania.

Jan 1, 1983

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of the Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper, in which he presents his own A factor.Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blasthole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, eg in conjunction with image-based fragmentation measurements or crusher modelling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function, such as in the KCO model.The mean to median issue is investigated in some detail and it is found that using x50 instead of the mean:has a sounder theoretical backgroundis less prone to errorsis not contradicted by the original Soviet data.It is finally suggested that future work on fragmentation prediction equations focus on the use of distribution independent quantities like percentiles, eg x50, x20 and x80. Some previous work in this direction is briefly analysed and one consequence is that the n-value of the Kuz-Ram model should depend on specific charge.CITATION:Ouchterlony, F, 2015. The median versus the mean fragment size and other issues with the Kuz-Ram model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P. deH. Eastcott

The paper summarizes a slide presentation made during the CIM Mechanical-Electrical Operators' Conference, held at Sudbury. Ontario, January 25-27, 1977. Its scope has been limited to a few specific aspects of modern Canadian hoisting plant practice that are likely to be of interest to operating personnel. It is intended to serve as a brief review of established methods discuss in more detail the present state-of-the-art and suggest trends that will appear as products during the next few years.

Jan 1, 1977

By Renato G. Bautista

The solvent extraction separation of nickel, cobalt and their associated metals have been considered for industrial application since the early 1960's. This review of the solvent extraction processes is limited to the industrial applications, pilot plant and the more extensive bench scale studies reported in the literature. The processes with their significant chemical and technological contributions are discussed in detail whenever the information are available. The application of solvent extraction to the nickel-cobalt processing has so far been limited to the secondary separation of nickel-cobalt containing feedstocks derived from other primary nickel-cobalt separation methods.

Jan 1, 1993

By H. A. Zollinger

The Hallmark Distribution Center is one of the most sophisticated material handling and order filling facilities in the world. The 53 million cubic foot facility houses an ultra-modern, computer- monitored distribution complex that handles as many as 1/4 million orders per day. The Distribution Center replaces 16 leased buildings scattered through- out metropolitan Kansas City and, in addition, re-leased 4 floors in mid-town Kansas City needed for creative and administrative expansion. This new facility is the nerve center for distribution of Hallmark products in United States and Latin America. The size and gross numbers of all parts of the system is a significant accomplishment, but the purpose of this paper is to explain the technical advancements in the state-of-the-art of material handling and controls. The system iteself is made up of seven sub-systems including receiving, warehousing, picking rack stocking, towline, order filling, order sorting, and shipping. Significant techniques were used in each of these areas as well as technical advancements in the state-of-the- art. The most significant points are in 4 of the areas and are discussed in this paper.

Jan 1, 1973

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010