Search Documents

By A. A. Paoli

The selection of a mining plant for carrying on development work presents many problems distinct in themselves, and affected by various local factors. In this paper, the writer proposes outlining and discussing in some detail the chief factors governing the economic selection of such plants. This will be followed by an enumeration of the underground and surface plant required for carrying on several hypothetical exploratory and mining operations. Where it is impossible or not convenient to obtain hydro-electric power, and where wood for fuel is scarce, we now find oil engines being used. A 100 h.p. oil engine, such as would be required to operate a three-drill air compressor, consumes approximately five Imperial gallons of fuel-oil per hour at full load. On the basis of a 60 per cent load factor, this gives, for eight hours' operation, a probable actual consumption of twenty-four Imperial gallons.

Jan 1, 1929

By W. D. Macleod

This paper describes a mineral dressing process for the upgrading of tin ores. The process described is called 'agglomeration' and. is similar in many respects to flotation. Many variables have been examined experimentally both on batch and continuous operations and are reported upon herein... Using a Mt. Pleasant tin ore, assaying 0.5% Sn, an upgrading to 8% Sn, with a recovery of 95% could be obtained by this process.

Jan 1, 1966

By M I. Roberts

As Australia’s mining industry painfully retrenches, mining executives and managers strive to remain viable by seeking significant productivity increases directly through process improvement and indirectly by improving leadership and workplace culture, the most powerful determinant of productivity. Culture is the combination of people’s attitudes and behaviour, together with leadership values and focus.Comprehensive new and automated data collection and management systems promise much for improving productivity, yet despite rapid advances in measurement and sharing of data, the use of data can reduce productivity unless behavioural aspects are considered and designed as part of implementation. This is because systems drive behaviour that in turn shapes attitudes to determine culture.Experience from many mine sites and other industries in three countries confirm that the most powerful drivers of people’s behaviour are the Measurement-Analysis-Reporting system and business leadership.This paper discusses fundamentals of practical, statistically valid process measurement, analysis and reporting systems before discussing associated leadership considerations for sustained improvement in safety, productivity, employee retention, leadership, accountability and commercial returns.The key to productivity improvement is improving core processes and important support processes. In turn, the key to process improvement is identifying the major process components and their interaction by measuring and then analysing their variation and level of performance. Understanding variation is often neglected yet is usually highly significant. It is essential that the fundamentals of statistically valid yet practical process and data analysis are understood and incorporated into system design to ensure productive, informed behaviour.The design and use of Measurement-Analysis-Reporting systems influences behaviour most profoundly and determines people’s effectiveness. Behavioural aspects are detailed by focusing on six primary drivers of human behaviour and five basic systems for managing businesses. These are integrated in a seven-step process and productivity improvement methodology that combines statistical, analytical, systems and behavioural factors.The paper includes development, implementation and tracking of a project plan for improving management and leadership systems to drive aligned behaviours. This key leadership responsibility is essential for improving performance to get the most from capital while providing people with the opportunity to develop greater autonomy, which is essential for self-discipline, responsibility, initiative and accountability.CITATION:Roberts, M I, 2015. Integrating measurement, systems and leadership to build safe, productive cultures, in Proceedings Third International Future Mining Conference, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By G. A. Van Wielingen

"The conditioning of natural gas to meet contract pipeline specifications involves in the majority of cases in Western Canada, the appropriation of substantial capital expenditures for treating and processing installations. It is therefore of vital importance to the owners and producers of natural gas to arrive at an appreciation of the economics pertaining to the production and surface handling of their gas reserves at the earliest possible stage of field development. The treating and processing of natural gas often results in considerable changes in composition and related physical characteristics between the wellhead and the point of delivery of the saleable gas. This paper presents a general outline of engineering calculations which can be applied in the pre-determination of the effects that surface handling of gas will have on the composition and physical characteristics of sale-able gas. Emphasis has been placed on the calculation of hydrocarbon dew-points, heating values and shrinkages prevailing at the various stages in the surface handling of natural gas. It is believed that advance information indicating the approximate ranges of these physical properties will facilitate process selection and will provide a basis for the estimation of capital and operating costs of process installations."

Jan 1, 1960

By Rajesh K. Mishra

The person in charge of Environmental Affairs in a small business has many higher priority projects (such as making money to meet the employee? payroll etc.) than filling out and filing the regulatory forms. It is but. natural to think that these affairs can be managed? by playing ignorant until audited by the regulatory -state and federal agencies. Truth is to. the contrary; generally, it is too late by then. The fines and legal costs even for failing to file the regulatory forms could deliver a serious blow to the financial well-being of a small business. Forms and reports under SARA Title III are not hard to complete., but they are time consuming. In this paper we will discuss the information and data compilation procedures, simplification of some legal terminology into simple technical language, and tips that help in filling out the forms?. Some actual case 'histories of EPA fines will also be reviewed.

Jan 1, 1992

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By D. Harrington

"While distribution of air currents to working faces is a necessity in coal mines, especially those having explosive gas, advancing faces in metal mines rarely have circulating air other than the ordinarily inadequate amount supplied through the compressed air system. Even where comparatively large quantities of air pass through main mine shafts and levels. whether the circulation is actuated by fans or by natural ventilation, only occasionally can a metal mine be found where any considerable percentage of the ""blind ends"" has circulating air of sufficient velocity to be measured by an anemometer or even be discerned by deflection of flame of candle, or of acetylene lamp; and unfortunately these ""blind ends"" include nearly all of the places from which rock is taken.During several years study of metal-mine ventilation in various mining districts of the United States, it has been found that in some mines many of the workers in ""blind ends"" practically continually breathe air with 0.02 to 0.04 per cent of CO gas from unremoved fumes from explosives; in other mines CO2 chiefly from timber decay and breathing of men, is so high that a candle will not burn though usually the acetylene lamp will, hence oxygen is below 17 per cent but above 12 per cent; in some regions CO2 from strata fills the entire mine forcing cessation of work; in other mines in dead ends, gases such as nitrogen, H2S, SO2, etc., are found under some conditions. In many regions with hot rock or water (especially in deep workings) men in blind ends must work with little or no circulation, in air above SO degrees F. and even above 90 degrees, relative humidity only too frequently being around 100 per cent; in other regions workers in blind ends in practically ""dead"" air must continually breathe enormous quantities of finely divided rock dusts. All of the above conditions are decidedly harmful to health and prevent the worker from delivering anything approaching an adequate quantity of work, and in addition, some of these conditions have direct or indirect effect in bringing about definite increase of accidents; all of the above mentioned bad conditions in ""blind ends"" in metal mines as well as their ill effects, are remediable by providing at those places adequate quantities of fresh circulating air."

Nov 1, 1923

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By J. V. Batty

In the course of the investigation of manganese mineral occurrences in the United States, Bureau of Mines examining engineers collected several lots of ore from the Black Rock, Kramer, and. Morgan-Cromar properties, Tooele and Juab Counties, Utah. Extensive laboratory tests were made to determine the amenability of the ores to standard ore-dressing methods of concentration. The Black Rock claims 1 and 2 are 42 miles northwest of Jericho, Tooele County, Utah. A. J. Huber of Salt Lake City and Ross Rydalch of Tooele, Utah, are the owners. The deposit-is reported to be a definite manganese fissure vein in quartzite along which considerable shearing and cross fracturing have occurred. Laboratory work was conducted on a 2-ton sample of run-of-mine ore procured by a Bureau of Mines examining engineer and two smaller, higher-grade samples submitted by the owners as a result of later development. The Kramer deposit is described as a bed of manganese oxides in quartz. The property is being worked by L. E. Kramer, Tooele, Utah, and is 41 miles northwest of Jericho) Tooele County, Utah, approximately 1 mile north of the Tooele-Juab County line. A 1-ton run-of-mine sample was submitted for testing by the examining engineer.

Jan 1, 1952

Problems caused by water discharge from surface mine ventilation shafts can be significant and are usually unforseen. The discharged water is often hyper-saline or acidic and can cause environmental degradation over a wide radius. It can also lead to recurring power pole fires and primary fan breakdowns. A range of solutions to the water discharge problem has been implemented in many Australian mines. In most cases the solutions have been ad hoc, with the overall cost and effectiveness varying tremendously. This paper reviews and contrasts the practicality and effectiveness of the various available remedial options.

Jan 1, 2002

By B. M. Hamilton

"IntroductionTHE PROCEDURE and technique for drilling holes has probably undergone as great a change during the past ten years as any one of the other operations conducted in hard-rock mining. During this period, we have seen a change from the heavy leyners and drifters to the light jackleg type of drill machine; from steels that were forged and hardened on the bit end to the inserted •carbide-tipped rod, from the necessity of providing special bit-end fabrication and beat treatment of shank steels to the simple grinding or turning of a plain section on a shank with no heat treatment required for bit attachment.When the steel maker was first called upon to manufacture a hollow drill rod, it was required that the steel must not only have sufficient strength and fatigue resistance to cope with the stresses of service, but also must be capable of being heat treated on the bit end to a high hardness for resistance to wear and abrasion . Little was known at that time about alloy steels and the beneficial effects to be gained from additions of chromium, nickel , and molybdenum. So it was that the plain 0.80 per cent carbon analysis was selected, since it had already proven to be a suitable grade for chisels, hammers, and other such shock tools. This grade has long endured the test of time and is still used in considerable tonnage today, particularly by the construction industry.As the metallurgist learned more about the influence of alloying elements, a new hollow drill analysis was placed on the market in the early 'thirties'."

Jan 1, 1954

Exploring long-term future possibilities for your business and methods for achieving them are critical functions of leadership. More than ever, strategic initiatives today have to be planned and delivered in an environment of disruptive change û driven by shifting business or regulatory imperatives, new technologies and global economic change, and diverse stakeholder interests. The notion of The Future as a single inevitable outcome is obsolete. There are many possible futures. This paper explains an innovative process û known as scenario planning û to help executives in the construction and testing of longer-term strategies to deal with uncertainty.

Jan 1, 2006

By T. F. Mitchell

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and obtained samples of ore from two properties in the vicinity of Bettie Mountain, Lander County, Nev. In addition, samples from three claims in the Carico Lake region, Lander County, Nev., were submitted by private interests. RS the ores were too low in grade to be acceptable for the direct production of ferromanganese, their amenability to concentration by ore dressing was investigated. The Black Bock property is 16 miles south of Valmy, Nev., and is owned by Western Alloys, Inc., Salt Lake City, Utah. The deposit is a replacement of sedimentary rock by manganese oxides. Ore occurs in two main ore bodies designated as the "upper bench" and "lower bench", which could be mined separately. Examining engineers obtained samples from each ore body, and laboratory experiments were made on each sample. The Black Eagle group of claims is in Lander County, Nov., about 43 miles southwest of Battle Mountain. Ore occurs as a replacement of manganese oxides in shale and chert. The 2-ton sample of ore used for laboratory testing was taken by a Bureau of Mines examining engineer from an adit that partly transversed a 28-foot bed of ore. The property is controlled by Western Alloys, Inc.

Jan 1, 1951

By C. T. Shaw

Fur a secure mineral supply position to be maintained in the Fiuropean Community there must be a supply of qualified people in the minerals industries. The education of the people required to run and develop these industries should be a priority in the community. This means that there should be a strong capability in mining engineering education. The mining engineering professors decided in 1990 to get together in a new Society to discuss the problems. The Society of Mining Professors/Societat der Berg-baukunde was formed at a meeting in Austria in October 1990. It is basically a F.uropean Society with a few member professors from outside Europe to keep the Society conversant with trends elsewhere. The objectives of the Society are to see that the mining universities in Fiurope maintain standards and produce enough mining engineers. The present membership of the Society and the work of developing a database of current courses is described. Working from the knowledge base developed, it will be possible to design a 'European' mining degree course. The problems which will have to be addressed have been identified and are described in detail.The paper finally goes on to discuss the other problems that universities are facing, the economic problems and above all the lack of students applying for mining courses across Europe. The help and active participation of the mining industry, if that industry still wishes to employ mining engineers, is identified as the only possible solution to those problems.

Jan 1, 1993

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By Ho SE, Neil Phillips G, Houstoun SM

There are numerous individual gold deposits in the Archaean greenstone belts of Western Australia, but only 26 have productions and/or quoted reserves in excess of 10 tonnes Au. Most gold production has come from mineralization in shear zones, quartz veins or stockworks in volcanic or intrusive host rocks, particularly tholeiitic basalts or dolerites metamorphosed at sub-amphibolite facies (e.g. Kalgoorlie). Significant prod- uction has also come from BIF-hosted deposits (e.g. Hill 50), and large reserves are quoted for mafic hosts at high metamorphic grade (e.g. Big Bell). Most deposits have marked structural control, great depth extension, and are characterized by zoned alteration haloes of pyritization (with Au), K-metasomatism and carbonation. On the regional scale, most larger volcanic- or intrusive-hosted deposits occur in younger (ca 2.8 b.y.) rift-phase green- stones (Norseman-Wiluna Belt). These belts also have a high prospectivity (36 kg Au/km2 of greenstone belt). Younger (ca 3.0 b.y.) and older (ca 3.5 b.y.) platform-phase green stones of the Murchison and Sodthern Cross Provinces and the east Pilbara, respectively, are progressively less prospective (14 kg Au/km2 and 0.8 kg Au/km2, respectively) and also have progressively smaller deposits. The important regional- and local-scale characteristics of most gold deposits can be explained in terms of a metamorphic- replacement model. In this model, metamorphic H2O-CO2 fluids, focussed by faults and shear zones, infiltrated host rocks and deposit gold at 350 + 50¦C and 1-2 kb, largely in response to fluid-wallrock interaction. In many large deposits, gold precipitation was synchronous with sulphidation of Fe-rich host rocks, but the diversity and abundance of smaller deposits reflects the variety of reactions precipitating gold from ubiquitous, auriferous metamorphic fluids. Regional variations in abundance and size of deposits relate to factors such as tectonic setting, alteration styles and possibly source rocks.

Jan 1, 1986

By L. C. Graton

At the Tenth International Geological Congress, Mexico, 1906, Waldemar Lindgren presented "The Relation of Ore Deposition to Physical Conditions." Retrospect ranks it as the outstanding offering at that Session and as the most fundamental contribution up to that date on the philosophy of ore deposition. Elaborating thereon in his text-book "Mineral Deposits," Lindgren analyzed ore-forming processes under conditions prevailing from great depth up to surface; explained the nature of deposition in each environment; and developed a comprehensive genetic ore classification, which brought wide acceptance and enriching contributions by many. Since Lindgren's latest edition (1933), have come wealths of material relevant to ore genesis, particularly through amazing renaissance and proliferation throughout science. Current publication regarding ores now emanates largely from a generation caught in pressures of the breathless modern tempo, which tempts scant reflection upon earlier truths. Consequently, today's thrilling output contains not a few offerings that need challenge because supplanting interrelationship and system by what seems, collectively, an assemblage of strange, ad hoc and often self-contradictory concepts. From these latter some merit may eventuate but at the probable cost of present confusion and delayed progress. The following pages, naming numerous post-Lindgren advances, record the conviction, held by many, that Lindgren's philosophy, progressively improved, remains the soundest approach to understanding ore genesis.

Jan 1, 1968

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929