Search Documents

By C. P. Mabie

This report summarizes studies by the Bureau of Mines in developing a simple method for estimating the phosphorus pentoxide (P205) content of finely ground sedimentary phosphate ores and beneficiated products. The method used involved leaching, filtration, and precipitation. The Bureau found that measurement of the volume of ammonium phosphomolybdate precipitate obtained from samples containing 16.8 to 37.7 percent P205 and the use of an appropriate calibration curve permitted estimates of percentage of P205 content accurate within ± 1.1 to ± 2.6 percent, respectively, at the 95-percent confidence limits. Incidental to mineral dressing and petrographic investigations of western phosphate ores in 1959, the Bureau of Mines undertook development of a simple process-control method for rapid on-the-spot evaluation of phosphate-mineral recovery. Because of the fine-grained and obscure character of western phosphate ores, chemical, rather than microscopic or petrographic, techniques were investigated. The described method involves acid decomposition of the ore or product, filtration, addition of ammonium molybdate reagent to the filtrate, and centrifuging and measuring the volume of yellow ammonium phosphomolybdate precipitate produced.

Jan 1, 1961

By L Hussey

Mt Keith concentrator treats low grade disseminated nickel sulfide ore supplied from the adjoining open pit mine. It is a traditional crushing, two-staged closed circuit grinding circuit (SAG & Ball Mills), followed by a complex split-size rougher, scavenger and cleaner flotation circuit. In 2016, 10.5 Mt was milled, at an average head grade of 0.54% Ni, yielding 35 000 nickel metal tonnes in concentrate.Historical analysis of the plant data indicated that of all the nickel lost in the fines rougher circuit tails stream, 25.6% was recoverable in an eight minute laboratory scale flotation test. These results implied that this fine nickel was readily available for recovery in the plant, either through operational improvements or additional flotation capacity. With operation optimisation ongoing, and capital within the business focused elsewhere, plant personnel were challenged to think differently about improving recovery.In 2012, a separate project to improve plant recovery when treating high talc ore was completed. Amongst other vessels, this project saw the installation of two 150 m3 Outotec Cells to the scavenger section of the fines rougher, middlings and scavengers (RMS 1) circuit. Since installation, the operation of these cells resulted in difficulties immediately upstream with instability in the scavenger cells. It was therefore decided that these cells would be better suited to treating the fines rougher circuit tails.The alterations required to divert these flows were minimal, with the capital project totalling $220 000.In the two years since installation, the fines rougher tailings nickel grade has dropped by 9.9%. The scavenger circuit has also seen a 2.8% reduction in tailings nickel grade, and instability issues were immediately resolved. This project serves as a lesson in how existing plant infrastructure may be better utilised to maximise recovery. Although this is especially applicable when capital constrained, such re-appropriation can be considered at any point to maximise return on existing assets. CITATION:Hussey, L, 2017. Repurposing flotation capacity at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 254–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D W. Stevens

Mechanical sampling provides a definitive value for the product sampled but the results are not instantaneous, meaning that decisions on process control can only be made hours after the sample is taken. Chemicals are added, tailings are sent to waste, stockyards are laid and the data for the decision-making is historical. Online analysers provide instantaneous information, allowing operators to make immediate and cost-saving decisions on the process. However, pending the specific online analysis application, there is a need for reference sampling for dynamic calibration/bias updating of the analysers so that they can deliver the desired precision and accuracy. What would be the economic justification for combining mechanical sampling with online analysis to reduce laboratory costs and provide immediate process control with certainty of accuracy? Approved sampling according to the Theory of Sampling, with immediate process control information.CITATION:Stevens, D W, 2014. Justification for integrating mechanical sampling with online analysis, in Proceedings Sampling 2014 , pp 135–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By A. Yörükoglu

In this study, thorium mineral that found in the complex ore deposit bearing bastnasite, fluorite, and barite from Eskisehir - Sivrihisar district has been tried to extract by using HCl and H2SO4 leaching. Ore sample of approximately 3 tons taken from the ore deposit has been homogenized in order to obtain composite samples by means of ore preparation techniques for experiments. Results of chemical analyses of composite samples are as given; 40.8% CaF2, 35.35% BaSO4, 2.01 Ce, 1.5% La, 0.39% and 0.1% Th. HCl and H2SO4 leaching processes have been performed to gain Th in the ore. For determining the optimum particle size, the samples have been ground under controlled conditions and brought to the sizes of 0.065, 0.2, 1 and 3 mm. Leaching experiments have been carried out in both HCl and H2SO4 acids without roasting and roasting at the temperature of 900°C for 1, 3 and 6 h retention times for all particle sizes determined before. In the experiments, the highest Th recoveries reached are as follows; 78.74% Th when H2SO4 and 1 mm particle sized sample used, and 1 h roasting applied and 73.38% Th when HCl and 1 mm particle sized sample used, and 3 h roasting applied. Keywords: thorium, leaching, concentration, sivrihisar, roasting

Sep 1, 2012

By Paul M. Tyler

One of the best present-day yardsticks of the material welfare of a nation is its consumption of minerals, The United States, with only 7 percent of the world population, consumes 45 percent of the world wealth, pays the highest real wages, has the shortest working hours, and numbers the largest percentages of home owners among its population, and at the same time its per-capita consumption of minerals is far greater than that of any other nation. In 1937, British India, with roughly twice the population of the United States, used less than 2 percent as much lead, 4 percent as muck zinc, and 13 percent as much copper; even in Europe, which has three times our population and where war preparations have greatly expanded the normal needs of peaceful industries, the aggregate consumption of metals and industrial minerals other than lignite is less than the total for the United States alone. The march of civilization passed from the Stone Age to the Bronze Age before the dawn of history. It may be questioned whether man or monkey first threw stones at an enemy, but only man could have fashioned rough stones into weapons. Eoliths rudely shaped by apelike men are believed by archaeologists to have antedated by hundreds of thousands of years the existence of our own human ancestors. The primitive people that followed the retreating Ice Cap northward in early quaternary period - at least a million years ago - were fairly adept in the shaping of flints and even used a little copper. The Bronze Age, so-called, superseded the Stone Age when, around 8,000 B. C., the news spread that chunk s of natural copper could be pounded into better weapons or cutting implements than ever could be made by chipping stones. The Bronze Age gave place to the Iron Age about 1,000 B, C., and though students of modern history may speak of the Coal Age, the Petroleum Age, and the Automobile Age, and so on, these ages have all been crowded into a brief century and a half. The truth is that we still are in the Iron Age, unless perhaps we choose to call it the Age of Many Metals.

Jan 1, 1940

By Daniel Harrington

For several years the United States Bureau of Mines has been making a study of ventilation in metal mines, this study covering practically all the important mining districts of the country. One of the districts where a close and extended study was made was that of Butte, Mont., with its numerous interesting problems and conditions. In February, 1916, Daniel Harrington, mining engineer of the United States Bureau of Mines, was detailed to investigate the circumstances surrounding the death of 21 men in the fire at the Pennsylvania mine at Butte, and during that investigation he made underground visits to several of the large mines through the courtesy of the mine operators, and became much interested in the ventilation conditions. In May, 1916, Mr. Harrington was detailed te work in cooperation with Dr. A. J. Lanza of the United States Public Health Service in an investigation of the prevalence and causes of miners' consumption in the district. This work broadened so much that the investigation was not completed until late in 1918, the investigators making a detailed inspection of all working places in four large mines and a more or less extended examination of conditions in about 20 other mines. Ventilation was recognized immediately as being an important factor in the health of miners, and from the outset of the investigation a large part of the work consisted in obtaining and compiling data relative to the flow of air, humidity, and temperature. The officialsof the North Butte mine were engaged in making a study of ventilation problems before the coming of the investigators, so that opportunity was given to work with those officials for several months. Detailed data on air flow, temperatures, humidities, and an analyses had been obtained before the fire in the North Butte mine June 8, 1917, which resulted in the loss of 163 lives. Much information was obtained during the progress of the fire, and a detailed examination was conducted after the fire, hence an exceptional opportunity existed to study conditions relating to ventilation. This bulletin is a result of studies made from the data collected during the two and one-half years of study and observation a-boveoutlined. Its publication has been delayed through lack of funds for printing. Other publications relative to metal mine ventilation -in other parts of the United States are expected to follow.

Jan 1, 1923

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By Van H. Manning

Chemical and physical tests of coals for the use of the Government have been made by the United States Bureau of Mines. These tests form part of a general study of the coals in the United States with respect to the manner in which each coal can be utilized most efficiently. As a result of this study, much information of value to all industries using coal has been compiled. Special investigations by the Bureau of Mines of the fuels used by the Government have, until recently, been for the most part limited to coal. In the course of these investigations the bureau has de- veloped new methods for use in the purchase of coal by the Gov- ernment. The application of these methods permits an intelligent selection of the coal adapted to the requirements of particular heat- ing or power plants, and has already resulted in the saving of large sums of money. In addition, these investigations have led to the compiling of a series of carefully made analyses of samples of coal collected in a predetermined manner in the mines of all the impor- tant coal fields in the United States, and these analyses are being published to enable Government purchasing agents and all users of coal to select the coal best suited to their needs. The purpose of this paper is to describe briefly the general char- acter and commercial quality of some of the coals mined in the United States that reach tidewater shipping ports, and to show in a general way the important characteristics of those coals that by reason of transportation facilities and the situation of the coal fields are most available for export. Coals of excellent physical character and of high heating value are available for export. For this reason and because of the modern facilities at the collieries for properly grading large shipments, American producers can supply coals suitable for any kind of service. The transportation system from the mines to tidewater and the coal- handling equipment for loading boats at the various ports are highly developed, so that producers are able to give excellent service to foreign buyers. Enormous quantities of these coals have been used by railroads, manufacturing, illuminating-gas, and coke plants, and seagoing vessels, and for household purposes. Much of the coal available for export is superior to the coals that have been supplied to foreign users from other sources.

Jan 1, 1916

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium. When the chairman of the conference organising committee invited (or was it instructed?) me to prepare and deliver one of the keynote addresses, his request was for me to be in parts historical, controversial, predictive and entertaining. The mix was left to me, with one proviso - that an early pioneer of mine filling in Australia be given due recognition. The chairman of the organising committee alone will be able to determine if I fulfilled the last objective. My success, or otherwise, with the other objectives will have to be judged by my fellow delegates. One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives.

Jan 1, 1998

By L Lorenzen, H Muller

"Every year a large number of projects are evaluated by small listed and unlisted mining companies that are hoping to find the ideal project, which will catapult them from a mining junior status to that of a mid-tier mining company. Usually this includes finding the æidealÆ or ærightÆ orebody and then developing a process which will allow cost-effective recovery of the valuable metals and the production of a saleable product. These dreams are seldom realised and there are a number of good and obvious reasons for this. Issues that are generally high up on the agenda for the smaller companies are: cost of developing a project before the feasibility study stage finding a suitable, or optimum processing technology financing of the project dealing with risk.The most expensive part of the development process for the small miner is often the exploration side of the business and finding the æidealÆ orebody. However, finding the right orebody will not be discussed in this paper. The æidealÆ orebody does not necessarily solve the problems of the mining junior, as much of the uncertainty lies in the process required to recover and produce the final metal product. Once a mineralised deposit has been identified and the grade at least reasonably qualified, the development of a suitable process becomes the driver to convert the deposit into an orebody. This paper proposes that a small exploration company has a very limited opportunity to succeed if it does not do sufficient homework before it identifies the æidealÆ orebody. The risk profile for the small mining company, by its very nature, has to be different to that of a major company and as a result the opportunities often lie in managing different and often new process options, which may be the key to bring such projects on line successfully.CITATION:Muller, H and Lorenzen, L, 2012. Project selection and process development for mining juniors, in Proceedings Project Evaluation 2012, pp 149-158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By J. S. Brock

Magnetic, electromagnetic and gravimetric surveys have played an important role in the mineral exploration leading to the discovery of three major massive sulphide deposits in the Anvil-Vangorda area of the Yukon Territory. During 1964 and 1965 a saturation prospecting program, relying heavily on the integrated use of airborne and ground geophysical survey techniques, led to the discovery of the Faro deposit, which was subsequently proven to be a 63-millionton lead-zinc orebody. Locating the Faro deposit, the largest found to date in this overburden-covered region, involved an exploration sequence requiring the selection of a favourable geologic environment, aeromagnetic and electromagnetic surveys, property acquisition of anomalous areas and detailed ground geophysical surveys, followed by rotary drill testing, detailed gravimetric surveys and diamond core drilling.

Jan 1, 1973

By S. M. Runke

The pegmatite investigations at the Rapid City, S. Dak., Experiment Station during; the pact 3 years have been primarily a study of recovering beryl from nonlithium-bearing pegmatite rock by continuous-testing methods. Beryl concentrates containing 25 to 88 percent beryl were produced from rock that ranged in beryl content from 0.1 to 2.5 percent. The beryl recovery ranged upward from 70 percent but averaged better than 80 percent. Although promising results have been obtained with flotation methods for upgrading these concentrates to standard specifications, additional work is needed to improve and simplify the procedure. In addition, it was demonstrated that several potentially useful coproducts could also be recovered from pegmatite rock. The principal coproducts were mica, feldspar, and quartz. A heavy-mineral product also was made from pegmatites containing tin, tantalum, and columbium. The recovery if these minerals in products meeting the specifications of the commercial users has been reserved for future study. The investigations also included studies on extraction of beryllium from both high-grade beryl and flotation concentrates of medium beryllium content. The procedure investigated consisted of sintering beryl or beryl flotation concentrates with limestone, acid curing the resulting sinter with sulfuric acid to dissolve the beryllium, and water leaching to extract the beryllium. Over 90 percent of the beryllium was extracted by this procedure. Most of the optimum conditions and quantities of reagents were determined for dissolving the beryllium. As aluminum and iron also were taken into solution by the acid, further research is needed on methods of recovering high-grade beryllium salts from the solutions containing these elements.

Jan 1, 1957

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By Constantin Pitis, Paul Slatter, Behnam Pirouz, Laura Contasti, Markus Zeller, Sadegh Javadi

"The centrifugal slurry pumps feeding cyclones are critical components used in the grinding process. It is well known that for this type of pumps the performance degradation is very intense. To minimize downtime a complete stand-by slurry pump is always installed in a parallel circuit. The replacement decision of slurry pumps is sometimes set on specific periods of time that are empirically determined, based on previous experience; unless a pump failure triggers the second (standby) pump. Given the significant energy costs in the grinding process and a desire to increase competitiveness, engineers and scientists started research in this field while manufacturers also took actions in order to improve pumps reliability and performance. The lack of standardization regarding the methods used to benchmark and evaluate the energy performances of cyclone slurry pump systems in the mining industry makes it difficult for an enterprise to take informed decisions concerning the replacement or optimization of its process based on energy benchmarking of such slurry pump systems. This paper proposes a new methodology of benchmarking slurry pump performances using a new concept of Benchmark Energy factor (BEF) based on Mathematical Model Benchmarking. The concept of BEF has been proven successful in other industries. A new standard addressing the guidelines for benchmarking the energy performance of slurry pumps for cyclones was proposed within the Canadian Standards Association. This standard will provide a unified and consistent methodology for performing measurement activities with the ability to measure and verify the system energy performance in the field through the BEF approach. Practical examples based on the new concept are presented with comments."

Jan 1, 2017

By L. Gonzalez-Sardi, W. McCombe, M. Pearson

Pressure oxidation is increasingly being used for processing refractory sulphide ores and concentrates because it offers highly effective base metal and precious metal extraction while minimizing elemental sulphur, arsenic & mercury emissions. Yet pressure oxidation processes introduce new safety concerns and process risks as demonstrated by a number of safety incidents over the last 20 years, including overfilling, oxygen-metal fires, nozzle/sparger failures, and uncontrolled pressure relief events. Chemical Process Safety regulations in the United States and Canada mandate that companies constructing or operating chemical process facilities perform a rigorous hazard and risk analysis based on either ANSI/ISA-84.00.01 or IEC 61511 safety standards to determine the level of protection required for each hazard in the plant. This paper describes the application and implementation of three (3) unique safety instrumented systems developed by Hatch for ensuring the safe operation of three different pressure oxidation processes.

Jan 1, 2014

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By F. P. Haver

Because of increasing concern with air pollution, the Bureau of Mines has developed a hydrometallurgical procedure to obtain elemental sulfur from chalcopyrite (CuFeS2) by means of the following reaction: CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S. Under optimum conditions, 99.6 percent of the copper and 71.6 percent of the iron were extracted in 2 hours from a typical mill concentrate containing 75 percent CuFeS2 and 15 percent pyrite (FeS2). At the same time, 68.2 percent of the sulfur in the concentrate was oxidized to the elemental form. The leach was highly selective; gangue minerals, including pyrite, were not attacked, thus accounting for the relatively low recoveries of iron and sulfur. To obtain these results, the concentrate was ground to 98.9 percent minus 325 mesh, and 300 grams was treated with 1 liter of boiling ferric chloride (FeCl3) solution. The FeC13/CuFeS2 ratio was 2.7. Cement copper containing 99.9 percent copper was recovered from the leach solution by cementation on sponge iron. Excess iron, dissolved during leaching and cementation, was removed from the stripped solution by crystallization. Ferrous chloride (FeCl2?4H2O), obtained as a byproduct, was converted to high-purity ferric oxide (Fe203) and HCI by an oxidizing roast. The hydrochloric acid was then electrolyzed to obtain chlorine, which was used to regenerate the leach solution. The leach residue, which contained ~50 weight-percent elemental sulfur, was treated with an organic solvent to recover the sulfur and cyanided to reclaim gold and silver.

Jan 1, 1971

By P. T. Brooks

Semipilot scale tests were made to demonstrate a newly developed electrorefining process which could be extrapolated to commercial scale in producing high-purity nickel and cobalt from crude nickel metal and high-grade ferronickel. The new process comprises application of solvent extraction techniques to remove and separate cobalt and iron from nickel and the electrodeposition in diaphragm cells of pure nickel and cobalt from chloride-based purified electrolyte. Using water insoluble organic amines, the solvent extraction operations enabled production of commercial-sized nickel and cobalt cathodes of higher purity than that of commercial electrolytic metals. The solvent extraction operation for separation of cobalt from nickel was made simpler than the conventional method. Furthermore, the solvent. extraction operation for iron removal made possible the electrorefining of ferronickel without the prohibitive loss of nickel resulting from the method ordinarily used for iron removal.

Jan 1, 1970

By Jan M. Andersson

This paper will discuss the background information about rock cutting tools used for soft ground excavation, their history and evolution. A brief review of the current state of the art manufacturing technology will be presented and some parameters related to the material used in the drag and conical type pick cutters and their impact on their life and performance will be explained In addition, the selection procedures for choosing the right bit for excavation of a particular geological formation will be reviewed A set of guidelines will be provided for initial selection of the tools for various machines and rock formations. The methods for estimation of the tool life in various materials and the influencing parameters along with limitations of the rock cutting tools will be discussed as well.

Jan 1, 1998

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010