Search Documents

By Laurent Dorel, Sebastien Maillard, Afchine Nasserian, Jean-Paul Faure

Surface quality monitoring is primarily implemented in the last steps of steel manufacturing before shipment to the end user. However, an increasing trend for also addressing this topic in the upstream stages, such as hot rolling plant, is tackled by Primetals Technologies to give steel producers the key to a global optimized yield management, and efficient “lessons learned” processes. After the last developments of SIAS Next Gen platform, including High Resolution and Near Infra-Red, some site results will be exposed on the very specific high constraints lines such as ESP Endless Strip Production and Plate Mills, and highlights the related most interesting aspects for our customers.

Oct 1, 2019

By Baoliang Xiao, Hui Pan, Yajun Hui, Kun Liu

The microstructure, properties, strengthening mechanism and work hardening mechanism of 600MPa grade high ductility hot-rolled sheet steel for automotive square tube were investigated by utilizing optical microscopy, scanning electron microscopy and transmission electron microscopy. The results show that the microstructures of low C-low Mn-Nb and Ti microalloyed steel (Steel A) and high C-high Mn-Nb microalloyed steel (Steel B) are composed of ferrite and a small amount of pearlite. Compared with steel B, the size of ferrite and pearlite of steel A is finer, while the size of the second phase precipitates is larger. The mechanical properties of the two tested steels are similar before tube forming, except that the yield ratio of steel A is higher. Steel A has/exhibits significant work hardening after tube forming; the yield strength and tensile strength increase by 45 MPa and 26 MPa, respectively, while the elongation decrease by 6.0 percent. The yield strength and tensile strength of steel B increase by 22 MPa and 10 MPa, respectively, and the elongation decrease by 4.0 percent. The grain refinement strengthening is the dominant strengthening mechanism, accounting for 52.9 to 61.8 percent of the total yield strength; the solid solution strengthening is the second strengthening mechanism, accounting for 17.2 to 25.3 percent, while the precipitation strengthening and dislocation strengthening contribute little to the yield strength. The dislocation strengthening increase by 82 MPa of steel A after tube forming, which is higher than that of steel B. Therefore, steel B has a low work hardening rate that is more suitable for manufacturing automotive square tube for secondary tube forming.

Oct 1, 2019

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Marcus Weldon

We are at the beginning of an era of profound transformation and human progress — a new industrial revolution. This “Automation of Everything” era will be brought about by digital interfaces, data analysis and control of the physical world through networks employing the Nokia Bell Labs Future X1 architecture — networks to support the digitization and connection of everything and everyone with the goal of automating much of life. The interconnection of robots, machines, drones, sensors, processing platforms and people through Future X networks will provide transformative tools for the automation and optimization of factories and warehouses, ports, electric grids, transportation networks, food, healthcare, construction, logistics and supply chain, emergency response, mining, and other physical industries. To date, the level of automation has been modest at best. Automating these physical industries — industries that account for 70 percent of the US Gross Domestic Product, for example — has the potential to drive significant increases in the world’s economic productivity.2 Realizing the potential of this next industrial revolution will require billions of wirelessly connected endpoints for high fidelity physical-to-digital conversion, millisecond response times to tightly control and coordinate machines and robots, and intelligent analysis to optimize real-time decisions — tasks beyond the reach of current networks. Increased levels of automation are already being achieved through the use of 4G advanced wireless access technologies. The untethering of sensors and actuators in industrial environments through the low-latency, high-bandwidth, high-reliability, and massive scale provided by 5G wireless access will complete this evolution, providing an unprecedented ability to digitize, analyze, comprehend and manipulate the physical world at a scale never previously thought possible. These new capabilities will enable us to create digital models of the physical world with ever higher levels of fidelity, further enhancing our ability to improve operational efficiencies and increase productivity and worker safety. Doing this will require a dramatic evolution in network architecture toward massively distributed cloud control and baseband capacity to achieve the required ultra-low latency and ultra-high bandwidth for industrial and infrastructure automation services — the Future X architecture. In early 2019, Nokia Bell Labs will publish a sequel to “The Future X Network: A Bell Labs Perspective”. “Future X for Industries: A Nokia Bell Labs Perspective” will explore how the Future X architecture will automate many of the world’s physical industries, including chapters devoted to electric power, cities, rail, mining, public safety, manufacturing, ports, logistics and supply chain, and an overarching chapter devoted to securing this highly automated world. To give you a small taste of the feast that’s to come, we’re sharing with you an initial installment — “Future X for Industries: Mining” — the Nokia Bell Labs view of how mining will be transformed through a Future X architecture..

Oct 1, 2019

By Karl Berger, Michael Steinkogler

The evolution in Metal Cutting: Inventors around the world have been successfully developing innovations for decades, but only some of these developments have had „GAME CHANGING“ potential. One of these innovations is the new developed saw blade LINCUT®, a patented changing system that paves the way for a fundamental reorientation of the entire saw blade industry worldwide through a simple and economical concept for rolling mills or heavy forging lines. Cost efficiency starts with the raw material: Circular saws equipped with a standard saw blade are expected to have a necessary 2 percent standstill per year due to required tool changing. The applied technology reduces this unnecessary loss of production by more than 50%. The ROI can therefore be reached faster which immediately lowers your production costs. No matter what material, conventional carbon steel or highly alloyed stainless steel, the coating and shape of carbide plates is perfected for extended tool life up to 25% with increased performance. Due to LINSINGERs own tool-technology-centre in Austria specialized in research and development of tools, constantly expanding R&D activities, best results are achieved in quality and cost efficiency: a (r)evolution in metal cutting.

Oct 1, 2019

By Zhisong Chai, Wei Xu

Q&P steels undergo continuous multiple processes, including hot rolling, intermediate heat treatment, cold rolling and continuous annealing etc. The inheritant effect of initial microstructure could affect the final microstructure and mechanical properties of Q&P steels. In this work, effects of different hot rolled microstructure/texture on the final microstructure and properties subjected to Q&P process were investigated in Fe-0.38C-1.58Mn-1.6Si system. Different initial microstructures were generated combing different TMCP and cooling strategies. The microstructure and texture of hot rolled materials were characterized in detail. The hot rolled material was subsequently processed by intermediate annealing, cold rolling and continuous annealing. The comparison reveals great effects of the initial hot rolled microstructures, i.e. inheritance effect. The faster reverse transformation would lead to more sufficient austenitization and it would greatly weaken the inheritant effect of the initial microstructure. Although the difference of final phase fraction for different initial microstructures was not significant, the inheritance effect was mainly reflected in the effect on austenite morphology. For the mechanical properties, no obvious difference in strength was shown for the samples with different initial microstructures after Q&P heat treatment, but there was fluctuation in elongation.

Oct 1, 2019

By F. D. Rodriguez, J. Ramirez Cuellar, J. Salinas Reyes, C. Gómez-de-la Garza

The Pickling Line and Tandem Continuous Mill (PLTCM) at Ternium Pesquería Facility with a Five Stands, Six High configuration started in 2013. Manufactured by PRIMETALS, to produce steel to exposed automotive market, Turnkey project, with supervision of best practices from Nippon Steel. The main equipment that the process has are; Laser welding machine, 3 loopers, Scale Breaker, jet Pickling tanks, Inspection Station and COGNEX System Side Trimmer (flying width change), Type of Mill: UCMW(S) Carrousel, 2 Tension Reels. The principals goals are, Simulate production programs, validate materials for thin thicknesses before processing, low Re-welds, optimization use Cognex, good performance in Thickness, flatness and productivity.

Oct 1, 2019

By Jose Maria Rodriguez-Ibabe, Ronaldo Antonio Neves Marques Barbosa, Douglas Glenn Stalheim

Major costs in the production of both flat and long commodity grade structural steel products include alloy, labor and energy. Flat and long commodity grade structural steels such as ASTM A36, ASTM A527Gr50, S235, S275, S355 and other equivalent world societal standards represent over 500 million annual tons worldwide. These simple commodity grades consist of a minimum of three base common alloying elements, carbon, manganese, silicon and then can be supplemented with microalloying elements of either vanadium or niobium. Since 2016 raw material costs for two of the five alloying elements in these commodity grade structural steels, FeMn and FeV, have risen significantly and/or have become volatile making it difficult to maintain stability in profitability for these commodity grades. For steel plants producing hundreds of thousands and in some cases over a million tons annually of these common structural steel grades because of the significant alloy cost increase for Mn and V alloy additions has squeezed profitability of these grades. These grades typically represent the base loading for cost controls in most all steel plants and hence a significant cost increase or volatility in two of the five elements used for these grades having a negative effect on overall production costs. However, with a proper strategy for alloy designs working in conjunction with the mills existing processing capabilities to achieve the desired end metallurgy/mechanical properties, alloy costs and operational efficiencies can be realized.

Oct 1, 2019

By Anand Kumar Agrawal, Kinzel Klaus Peter, Lorenzo Micheletti, Cristiano Castagnola, Horst Kappes, Andre Oliveira, Björn Rösner, Philippe Bermes

Blast furnaces are widely employed today for iron production all around the world, with a total production of around 1.2 billion tons per year. Its operating principle, which relies on usage of coke to reduce the ore, to ensure the permeability in the reaction vessel, to maintain its flexibility of operation and acceptability for varying qualities of iron ores. The blast furnace route is widely considered as the most economic and efficient route of iron production, however it is based on fossil energy carriers. The blast furnace route has undergone significant developments in terms of energy efficiency in the last decades, which led to a substantial reduction in the use of fossil reduction materials. Being an energy intensive process, competitiveness and cost saving in the blast furnace plant was always strongly related to the saving of energy and hence reduction of CO2 emissions. In addition to this, EU emissions trading system (EU ETS) as a cornerstone of the EU's policy in response to climate change has set new “challenges” for iron production in Europe. Paul Wurth has always been deeply involved in the development of energy saving technologies for blast furnaces. In the following a review of energy saving achievements developed in the last decades will be presented and the potential of available CO2 saving technologies will be summarized. Additionally, an outlook about the potential of future technologies, concepts and their impact on the blast furnace and the steel plant’s energy balance will be discussed. Finally, the replacement of carbon by hydrogen as reduction agent in the steel plant will be reviewed, with special focus on a comparison of costs and incentives.

Oct 1, 2019

By Danilo Gonçalves de Oliveira, Rogério Martins Pereira

Chatter is a widely studied vibration phenomenon that affects most cold mills around the world and its impact on these lines are tremendous: from productivity and quality losses to mechanical equipment damage. The investigation of its origins and how to minimize the occurrences and their impact on the equipment require special instrumentation and algorithms in order to have a detection of the vibrations as soon as they start. This paper presents three methods of identification of chatter on a Tandem Cold Mill and the actions to leave the vibration frequency range before its amplitude achieve catastrophic values.

Oct 1, 2019

By Johan PEERS, François DUMORTIER

Today, solutions to optimize Capital Expenditure (CAPEX) & Operational Expenditure (OPEX) for small capacity Cold Rolling Mills (CRM) as well as for high capacity CRM are available, as extensively described by various Original Equipment Manufacturers (OEMs) & steel makers. A suitable solution for small capacity CRM is to start with a single stand reversing mill (up to 400 ktpy, depending on product mix), which can then be expanded into a twin stand mill (up to 900 ktpy, depending on product mix). The main drawbacks in conventional practice are the off-gauge length in single stand set-up and the long downtime of the mill during the erection of the second stand. For higher productions CRM, it is common practice to directly select a new Pickling Line Tandem Cold Mill (PLTCM), with a high CAPEX. Is there an in-between solution that would allow to start with limited output and CAPEX, without jeopardizing the ultimate expansion goal (1.2 to 2 mtpy), for which PLTCM is the best techno-economical choice? In the absence of a solution, JOHN COCKERILL developed an integrated solution that limits the CAPEX in the first phase of development, without crippling affecting future endeavors through an easy and economically sustainable expansion into a PLTCM, without long production downtime. The solution consists of first installing a twin stand mill, expandable into a tandem mill thanks to a smart design of the line. It is therefore possible to limit the production to 900 ktpy in the first phase of the project and then convert the mill into PLTCM in the second phase to increase the production from 1.2 to 2 mtpy, depending on the market trends and financial capabilities. In summary, JOHN COCKERILL has developed a smart new layout in reversing phase combined with a brand new rolling strategy to optimize productivity and limit off-gauge, compared to conventional solutions (patents pending). In addition the layout enables an easy conversion to tandem mill without high over investments, which is more sustainable financially than the initial purchase of a PLTCM. Long downtimes to allow for capacity extension, detrimental to this phase-by-phase approach, are also avoided. Technical and process description of the new layouts and rolling strategies, together with CAPEX & OPEX descriptions of the phases are detailed in this paper.

Oct 1, 2019

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Rafael Abreu Fraga, Carlos Noberto Paula da Silva, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Since 2016 Gerdau Ouro Branco has been producing steel plates of various qualities and grades. However, it was not until 2018 that the first plates produced by accelerated cooling process were made available for external testing, in this case for large diameter UOE pipes manufacturing. Recent line pipe and OCTG specifications are showing that the oil and gas market still consumes regular API grades, such as X60, X65 and X70, however with increasing wall thicknesses, reaching values up to 1.5 inches. These specifications also demand longitudinal and transverse tensile guarantees and drop weight tear tests in temperatures as low as -40°C. Projects with these types of mechanical properties present process requirements as challenging as those necessary for higher API grades in lower thicknesses. This paper shows the steel design concepts and rolling routes for achieving the necessary properties for X70 steel plates in 28.15 mm. The microstructural features were also investigated and associated with the production process and the tensile and toughness results. Finally, challenges such as tensile anisotropy and DWTT abnormal fracture are presented.

Oct 1, 2019

By Milca Ventura dos Santos, Ricardo Rodrigues Grizotti, Luciano Henrique Andrade de Resende, Francisco Ricardo Casa Neto, Paulo Roberto de Oliveira Junior, Bruno Rodrigues Ferreira

O trabalho tem por objetivo demonstrar o processo de desenvolvimento e implantação da automatização nas operações, atividades de almoxarifados (recebimento, armazenagem, movimentação, inventário, picking e entrega de materiais), com o uso da tecnologia SAP FIORI com interface nos sistemas operacionais Android e IOS para utilização do Mobile (smartphones e tablet’s), já alinhado ao momento da indústria 4.0, visando inovações tecnológicas nos campos de automação, controle e tecnologia da informação. O desenvolvimento nesta nova plataforma visa tornar as operações de almoxarifados mais ágeis e eficientes, buscando otimizar o processamento das informações com mais rapidez, redução do tempo de permanência das mercadorias nas áreas de transferência e gerar maior rastreabilidade dos processamentos com interface direta e on-line com o ERP-SAP da organização. A metodologia do trabalho foi identificar as oportunidades de explorar as melhores potencialidades das soluções do SAP Fiori, alinhadas aos sistemas operacionais Android e IOS para uso de celulares, tablet’s, com comunicação através da rede interna e/ou 3G/4G sempre visando otimizar todas as atividades operacionais (fluxo de materiais) e administrativas (fluxo de informações) dentro dos processos dos almoxarifados e suas áreas de interface. O projeto iniciou-se e sendo implementado nas unidades de Planos (ArcelorMittal Tubarão e Vega), e com plano de expansão para as unidades de Longos da ArcelorMital Brasil durante o ano de 2019. Nesta primeira etapa o resultado alcançado foi de plena adequação, tendo sido encontrado benefícios em redução de erros; aumento de segurança; redução de custos; otimização de processos; transparência em dados; customização de produtos, o qual espera-se que a curva de aprendizado naturalmente nos levará a adoção de novas soluções incrementais resultando nos melhores níveis de gestão do processo de armazenagem e movimentação de materiais.

Oct 1, 2019

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Juliano Braz Possatti, José Fagundes Júnior

This project involved a teamwork including process control, maintenance and operation specialists, R&D and CTO experts to identify and actuate on each opportunity to increase charging temperature, furnace efficiency, decrease discharging temperature when possible, decrease FM and RM cycle time (mainly speed increase and interpass time decrease), tracking zones optimization, safe use of equipment power limits, safety interlocks revision and tune models for Mill Pacing Control and Slab Design.As result of these efforts, ArcelorMittal Tubarão HSM today occupies a prominent position among the best HSM of similar layout and produced mix of the group and worldwide. This paper will show the path which was followed by the AMT HSM team to achieve more than a 20% productivity increase resulting in a hot coils production per year more than 700 million tons higher.

Oct 1, 2019