Search Documents

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000

By M Titley, M NoppT

A study on the feasibility of mining the recently discovered Wallaby gold deposit is due for completion by mid-2000. Open pit mining is the favoured method. Determination of the impact of mining bench height on the recovery of ore, including the estimation of dilution and ore loss, is critical to the economics of the operation. Conditional simulation was used to derive a number of gold estimation scenarios within a typical volume of the deposit. These scenarios were interrogated for a selection of mining bench heights and ore block dimensions. The results were reported as a range of grade tonnage relationships and compared to the kriged resource model. This allowed the resource model to be calibrated to a specific mining bench height and ore block size. Once calibrated, more realistic dilution and ore loss values for a number of mining bench heights were calculated from the resource model. These values were then used to determine the economic sensitivity of particular mining methods. The spread of results from the simulations also provided an indication of the confidence in the kriged grade estimates for the different zones of mineralisation within the deposit and highlighted areas of any significant uncertainty.

Jan 1, 2000

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

By T. R. Rehak

Blasting operations are an essential element in the recovery of our Nation?s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining. Blasting accidents in the mining industry tend to result in critical injuries or fatalities. Accident reports and information collected from the Mine Safety and Health Administration (MSHA) and other government agencies provide supporting evidence. According to the data collected, blasting-related accidents (in mining) were 11 times more severe than all other types of mining accidents. Blasting accidents are not unique to mining operations - the same situation exists in the construction field. In this paper the authors have compiled a list of the primary causes of flyrock and the failure to secure the blast area. In the next phase of this project, typical blasting scenarios will be reviewed which will highlight the main reasons flyrock and/or lack of blast area security occur. This will alert miners and construction workers to the current problems/hazards associated with blasting and to identify other safety measures to protect personnel.

Jan 1, 2000

By T Blyth, D Holden, N Archibald, S Huffadi

The Morning Star mine is owned by Hill 50 Gold NL. Gold is hosted in quartz-carbonate ¦stibnite ¦molybdenite veins that occur in a series of deformed, altered and metamorphosed mafic volcanics with subordinate sediments and felsic intrusive rocks. The irregular gold distribution and its relationship to structure and alteration intensity makes the definition of stoping limits difficult. Understanding the structural evolution of the orebodies and the contemporaneous and later structures that affect the orebodies has been very useful in this context. This paper reports on a detailed mapping exercise (as part of a more extensive and on-going investigation) and the integration of this mapping with other geological and grade control data in a 3D modelling environment to provide an expanded basis for stope design. Three types of mineralised zones can be discriminated based on the morphology of the veins within. They are:those associated with strongly folded, thick veins (approximately 1 m thick eg 05 orebody); those comprising planar, boudinaged and some folded veins which consolidate to form tabular, steeply dipping bodies (eg 010 orebody); and zones containing the above vein types and thin, highly deformed veins within zones of intensely foliated country rock that result in localised, irregularly distributed high-grade gold zones (eg 02 orebody). The mineralised zones associated with thick folded veins are typically predictable over many tens of vertical metres. The second and third types of ore zone is generally less predictable. Detailed mapping and structural kinematic studies indicate all ore zone types are affected by progressive deformation involving strong strain partitioning. It is interpreted that high strain zones, recognisable by intense foliation development and highly deformed veins, are the latest stage of a progressive deformation which approximates bulk flattening. Structural controls on mineralisation can be defined at two different scales.Regional scale folding has deformed a sequence of mafic volcanics with interlayered sediments and felsic intrusives. Initial geometry of felsic bodies relative to orientation of the primary lithological layering and the bulk shortening direction is interpreted to be critical for initiation and development of strongly dilatant zones within this package of rocks, and Local scale dilation is evidenced by development of several vein sets whose range in orientations and opposed vergence relationships suggest a pre-folding origin comprising both extensional and hybrid shear-extensional types. Continued deformation resulted in folding of these veins with strong strain partitioning. Major vein packages are closely spatially associated with the felsic/mafic contact and an interpreted early structure which appears to have partitioned early dilation. This structure is now obscured by strong deformation but is currently represented by a zone of planar veins.

Jan 1, 2000

Determining the controls of high-grade mineralisation at Vera Nancy requires careful data collection and assessment on a global and specific deposit basis. The techniques developed over 60 years ago to analyse structure, grade and width data are just as applicable today and can be enhanced using modern geological modelling software. High ore grades at Vera Nancy are controlled by both the primary geometry of the mineralised structure and the intersections of the main mineralised veins with subordinate splay veins. The main mineralised structure dilated as a consequence of extensional tectonics while the splays acted as conduits bringing oxidising surficial fluids into mixing zones precipitating high gold grades. Near-mine exploration is focussed on identifying zones of vein flexure and splay interaction to locate the relatively small high-grade shoots. Data modelling in a 3D environment is an essential process for understanding the geometry of the system being explored.

Jan 1, 2000

By V. M. Sokolov, Jr. DuPlessis

The technology for recycling fine wastes, grinding sludges or swarf, and solids such as slag that contain a high content of metallic material needed improving. The objective was to produce a master alloy that met the tight requirements of the Western manufacturers and achieve improved yields of the valuable elements, nickel and cobalt, to over 90%. The alloys from the production of Alnico. magnets were chosen for this work. A process is proposed .that is able to recycle all kinds of Alnico wastes. This process is able to reduce all detrimental elements, which are contained in the wastes, to within acceptable levels. Molybdenum, if present, is an exception. Depending on the levels of contamination of undesirable elements different recycling strategies are proposed. The majority of the wastes can be recycled by melting and refining with a liquid slag layer using unique melting furnaces that are relatively unknown in Western nations. The proposed technologies allow the reelamation of over 95% of the cobalt and nickel from any kind of Alnico waste, and there are no limitations on the proportion of different kinds of wastes in the charge. The proposed processes and technologies could also be applied to the recycling of grindings, turnin

Jan 1, 2000

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By S. S. Chabot, S. E. James

A recent survey of CEOs from major steel companies worldwide revealed the importance of recycling zinc units from EAF dust, mill scale, blast furnace dust, and other zinc containing streams in their plants. Many processes were developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and selling it to primary zinc producers to recover the metal value. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of corrosion problems it will cause in electrolysis. In 1999, BRZ installed a zinc oxide receiving and washing plant to minimize the impact of halides to its circuit. A description of the washing plant and initial operating results are included.

Jan 1, 2000

By Simon C. Dominy, Ian M. Platten, Garry F. Johansen, Alwyn E. Annels, Brian W. Cuffley

Abstract - Coarse gold-bearing veins are characterized by high grades that are localized and erratic. Effective sampling of coarse gold-bearing veins is difficult because of the low concentration and erratic nature of the gold particles. Diamond drilling is an effective measure of geological continuity, however, grade distribution can only be reliably obtained from underground development (including close-spaced sampling, bulk sampling, and trial mining). Comparison between surface and underground drilling, underground linear/panel and bulk sampling indicate that drilling and linear/ panel samples generally understate bulk sample grades. Bulk samples are likely to be the closest estimators of true grade. It is unlikely that anything above an Inferred Resource category can be estimated from surface drilling alone, and at best the grade will only be a global estimate. Underground development, in-fill drilling and bulk sampling/trial mining will be required to delineate Indicated and Measured Resources. Closely spaced development and bulk sampling is likely to be the only way to determine Reserves. The resource estimation process must driven by a clear geological model that should attempt to understand both geological and grade continuity. Traditionally, grade interpolation has been undertaken using classical methods, though more recently, computer-based block modelling techniques have been used with some success. Three case histories are presented, documenting the problems of estimating resources in coarse gold-bearing veins and the practical ways in which they were approached.

Jan 1, 2000

Just as geophysics, in the form of 3D seismic and wireline logging, plays a key role in petroleum reservoir management, so too will geophysics play an important role in mining of coal, metals, and minerals in the 21 st century. The commercial and social imperatives driving greater use of geophysics are reduced costs, increased revenues, and enhanced safety. In short, superior utilisation of capital and management of risks. In relatively undeformed sedimentary environments it is possible to adapt petroleum-style 3D reflection seismic to image mines. This has been demonstrated most impressively in the Witwatersrand. Anglo-American, for example, completed a $1 million 3D seismic survey at Western Deeps in order to site a new $300 million shaft with confidence. Likewise, 3D seismic has gained rapid acceptance at Australian coal mines in recent years. Encouraged by these successes, metalliferous mining companies are supporting research in Canada and Australia, as well as South Africa, to adapt 3D seismic for more highly structured, metamorphic terranes. Because the mining industry is far more diverse than the petroleum industry in terms of commodities and geological environments, 3D seismic is not always cost-effective. A plethora of other geophysical techniques can be applied, many of which are employed in mineral exploration. Mine applications of geophysics differ from traditional exploration applications in two main ways: time scales and length scales are shorter, and boreholes are more plentiful. Borehole geophysical techniques therefore play a more significant role, both for logging and imaging. Logging systems detail the variations of in situ physical properties down the borehole at scales measured in centimetres, while geophysical imaging techniques can map features located tens or even hundreds of metres from the sensors. While geologists tend to think of boreholes in terms of chips and core, geophysicists perceive them first and foremost as access paths for instruments. Borehole logging has been employed at iron and coal mines for decades, mainly to accurately define ore boundaries in delineation holes. In base metal mines, Outokumpu implemented logging widely for orebody delineation in percussion holes in the 1980s. The benefit was a direct cost-saving, arising from substitution of core drilling with percussion drilling plus borehole logging. The practice has since spread to other companies. INCO, for example, defines nickel boundaries in blast holes at Sudbury using conductivity logs. The benefits are in the form of reduced dilution and enhanced ore recovery, flowing from a more accurate mine model. Density, natural gamma radiation, magnetic susceptibility, and conductivity are the principal metalliferous mine logging parameters because they can be recorded in both dry and water-filled holes. Sonic velocity is the premier geotechnical logging parameter, given its sensitivity to rock strength, stress, porosity, and degree of fracturing. Sonic is recorded routinely in exploration and geotechnical holes at coal mines. With the advent of slimline dipmeter, full waveform sonic, and optical and acoustic scanner tools, the role of borehole logging in geotechnical evaluations is expanding. Monitoring of strain and micro-seismic activity enhances safety during mine production. While qualitative interpretation of logs is adequate for stratigraphic identification or definition of boundaries, a wealth of quantitative information, eg density, can be derived from properly calibrated, repeatable geophysical logs. Moreover, geophysical logs can sometimes serve as surrogates for geochemical assays, and not only for magnetite and uranium. At OutokumpuÆs Kemi chromite mine, for example, gamma-gamma logging provides the basis for grade control. By reducing reliance on assaying, three benefits can be realised: reduced reliance on core drilling; lower core handling and assaying costs; and shorter turn-around times. Conventional downhole EM and borehole magnetics are used for near-mine exploration, and for ground sterilisation. Inco has enjoyed considerable success with borehole UTEM in the Sudbury Basin, for example, and Geopeko has applied three-component borehole magnetics successfully in the Tennant Creek area. Electrical techniques such as applied potential and magnetometric resistivity (MMR) are also finding application at mines. For higher resolution, borehole seismic, radio imaging, and radar have been invoked, with varying degrees of success, to delineate orebodies and map structures, or to geotechnically characterise the rock mass and identify hazards. Success mapping nickel sulphide shoots with borehole radar has been reported by WMC at Kambalda. There are no universal geophysical panaceas, and each mine imposes different geological, logistical, and economic constraints. Geophysics will not always be cost-effective. However, the greatest single impediment to expanded use of geophysics at mines has been the low level of awareness of geophysics on the part of most mine geologists, engineers, and managers and, equally, the limited understanding of mine geology and engineering exhibited by the majority of geophysicists. This myopia will be remembered as a 20th century affliction! Blue Sky areas for mine geophysics in the next ten years include integration of geophysical data acquisition with drilling, enhanced grade estimation and rock mass characterisation, and the incorporation of geophysical information into mine models using geostatistical techniques. All these advances will be predicated on an expansion of petrophysical knowledge.

Jan 1, 2000

By D. H. Rubisov, V. G. Papangelakis

Sulphuric acid pressure leaching is the process of choice to recover nickel and cobalt from laterites with variable iron and magnesium contents. The latter influences the acidity levels required for effective leaching of nickel and cobalt, and during leaching, iron is rejected in-situ as hematite. Classical solid/liquid separation is performed via a CCD circuit, the performance of which depends upon the size and shape of precipitated particles. In this paper, precipitates obtained by acid-leaching of various lateritic feeds at 270°C are characterized using SEM/EDX and laser particle size analysis. It is shown that as acidity increases, the shape of the precipitates gradually changes from platelets to spheres, thus improving the S/L separation properties of the residue. The use of hydrogen ion concentration “at temperature,” calculated from a speciation analysis, allows the explanation of this change of morphology independently of the type of the ore feed. The possibility of precipitating magnesium sulphate “at temperature” is also discussed. In order to take advantage of this precipitation for scale reduction (as has been proposed in the past) without compromising the residue quality, [H+] “at temperature” must be controlled within an optimum range.

Jan 1, 2000

By P. -M. Tardif, S. Outalha, R. Le

"This paper proposes a new direction to implement an underground mine communication system. It presents actual underground communication systems and discusses their technological limits. A new system based on a wireless local area network (WLAN), together with its main systems characteristics, is then proposed. This paper also presents an experimental protocol for radio frequency propagation measurements. Finally, the paper describes the projected implementation of a WLAN in an experimental mine. IntroductionDuring the last decade, a number of Canadian mining companies have invested in modern communications systems in order to automate processes and reduce operational costs. Safety of miners is also a concern, regulated by health and safety regimes.Underground communication systems rely mainly on analog technology (especially the leaky feeder). Digital upgrades have been made to modernize this technology using a coaxial or fibre optic cable to transmit voice, documents, commands, controls, and video. Therefore, all wired equipment can benefit from an increase in efficiency from the digital technology.However, when it comes to mobile equipment, the only medium was, and is, still radio waves. With the advent of the wireless local area network (WLAN) standard, one can use a technology similar to that of the cellular phone to connect transparently different equipment. WLAN enables the transmission at rates higher than 2 M bits of voice, documents, commands, controls, identification, and of course, digital video. This technology was developed with inbuilding use in mind. Now, one can try to adapt it to underground mines."

Jan 1, 2000

By P SSrkkS

Mining is commonly seen as a typical basic industry with rough and even dangerous working conditions, heavy environmental load, and a low level of high-technology and automation with much manual work and operations. A mining operation (open pit or underground) is a very complex one consisting of many manual, physical, mechanical and logistical operations with different human interfaces and decisions. For this reason it is a demanding and potential area for all applications of automation and information technology: controlling difficult non-linear, time varying multivariable processes and machines; solving of ergonomic safety and environmental problems; automation of logistical systems; applying robotics, mechatronics, and information handling, etc. In addition to that, big economic sums are involved with these operations. On the other hand, automation technology has developed towards intelligent and adaptive systems including some from the above mentioned fields of automation. Connecting them with modern information and communication technologies makes the idea of an intelligent and unmanned mine more and more feasible in the near future. This requires intensive co-operation and co-ordination between the mining industry and manufacturers of mining machinery. This has been successfully accomplished in the five-year Intelligent Mine research and development program as well as the three years of subsequent implementation of its results in Finland. The basic elements of an Intelligent MineTM concept are:mine-wide information and data acquisition system; high-speed two-directional mine-wide communication network for real-time monitoring and control; computerised information management, mine planning, control and maintenance systems; automated and tele-operated machinery and equipment which are connected to the information system; and links to the public information networks. The degree of automation of an intelligent mine depends on many technical and economical factors. The basic precondition for such an approach is that it will improve the total economy of the mine. This paper will describe the Intelligent Mine Technology Program with the results. Also the implementation which took place during starting of a new underground mine (Outokumpu Chrome Oy Kemi Mine) will be described.

Jan 1, 2000

The operations management system at Olympic Dam has evolved over a two-year period to the state described in this paper. This evolution has been driven largely by the requirements of the recent expansion of the Olympic Dam operation from three to nine million tonnes of ore per year. Such a change process demands an holistic approach to mine management and several techniques have been employed including XPAC, Mine Works Planner as well as a basic philosophy of æjust-in-timeÆ completion. The philosophies, software and tracking mechanisms for managing a large tonnage operation are described, outlining a fully integrated scheduling system from shift to shift detailed activity planning to a 20 year production plan. Moreover, the vision of production exceeding the current limit of nine million tonnes means that there are to be further developments to this state-of-the-art system in use at the Olympic Dam mine.

Jan 1, 2000

By R Chinamatira

Several technical and economic factors have to be taken into consideration in developing an optimal mining method. This paper describes some of the important factors learnt during the evolution of the sublevel cave mining method at Trojan Nickel Mine, part of the Bindura Nickel Corporation (BNC) in Zimbabwe. Sublevel caving (SLC) has been successfully implemented at Trojan mine since its introduction in 1994. The method has evolved over the past six years into a system that has brought about improvements in efficiencies and productivity. Although the original design parameters used were sound and provided a solid foundation for the system, they needed to be optimised to get the best out of the mining method. Improvements and changes have been made in areas such as the drilling process, charging and blasting techniques, ring pattern design, development size and shape, and the draw control system. This has enabled the mine to develop an SLC operation that is efficient and innovative. Experience gained, together with the theory available has given us a much better understanding of the system. This knowledge will be used in the future to enhance the system further. Given the low grades of the BNC Mines, management recognises that only through technical excellence and efficient mining can the mines reduce mining costs and maintain profitability and competitiveness on the world market. In the Zimbabwe mining industry reaction to technological change, mechanisation and advancement have been relatively slow, due to isolation and economic constraints, compared to the rest of the world. Economic difficulties prevail, with high inflation levels, a poor exchange rate, lack of foreign currency and other associated problems. Despite these constraints, the bold steps taken have transformed Trojan mine into a more efficient and competitive operation, presenting itself as the leading mine in the BNC group. Appendices give data to illustrate the benefits obtained.

Jan 1, 2000

By G R. Howard, G Back

Management of information systems for data collection is essential to maintain data integrity and continuity, and manage loss control on a large world-class mine such as Telfer Gold Mine. This paper aims to describe the individual systems and protocols of geological data capture at Telfer, then focus on Quality Assurance Quality Control data as an example of loss control in practice. Loss control systems are required to provide capacity, flexibility, structure and management tools to enhance data interrogation. The data that have been collected can then provide geological, financial, environmental, and contractual information to optimise management of business best practice. Telfer Gold Mine is a wholly owned and operated subsidiary of Newcrest Mining Limited. The mine is located in a remote area of NW Western Australia, and has been operating for 20 years. Geological data have been collected at Telfer since 1973. The data include drilling, assay, geological, survey, structural and geophysical data. Data management has evolved through many systems with data stored on many different hardware and software platforms. Commencing in 1995, collation, standardisation and validation of the historic data was completed. This has resulted in the first Access based drill hole database incorporating all available drilling data. This drill hole database, now hosted in SQL Server, is the hub for all geology related data management systems. The Telfer Gold Mine Geology Department has developed a series of inter-related database systems in order to manage the core geology business issues. Databases relating to drill hole planning, drill contract management, geological logging, accounting (standard costing, forecasting, invoice reconciliation), quality control (QAQC), and environment rehabilitation have all been developed to manage loss control. Management effort to provide adequate data systems and protocols has driven the system from concept to utilisation. The improved productivity, data integrity and data analysis capabilities provided by the new database systems at Telfer have allowed for greater confidence in decision making. Systems such as the drill hole and QAQC databases, when utilised in the proper manner provide up-to-date data analysis for resource audits and contract negotiations. The loss control systems are essential to maintain confidence in data integrity and hence directly effect the future of mining at Telfer.

Jan 1, 2000

While ring-blasting techniques offer substantial benefits, there are intrinsic problems that are exacerbated when large blocks of ore are mined in attempts to improve the production economics. These problems relate to both the convergence of holes around the ring drive and the charging of up-holes. The size and shape of the ore block concerned should be carefully considered so that good drilling, patterns can be achieved. The hole diameters chosen, both affect and are affected by the size of the ore block. The explosive selected depends on the hole diameter and together with the diameter, determines the nominal drilling pattern. Ring-drilling patterns are best derived through the use of computer software together with engineering judgement. The loading of explosive is necessarily high, and charging patterns require careful thought if overcharging is to he minimised and adequate energy is to be available at all parts of the ore block. Initiation systems are critical to the blasting results, but sub-optimal systems must be adopted if collar priming is practised. In view of all these factors, idealised guidelines can be given for ring design, but it should be recognised that developments in technology may in time change some of these parameters.

Jan 1, 2000

By S. Ferlay

"The main purpose of the ZIMA VAL project (Label EUREKA EU1367 and LIFE ENV/F/000278) is to demonstrate industrial scale recovery and recycling of the main components of used dry batteries (zinc, manganese dioxide, mercury, and stainless steel) into high added value products. The originality of the ZIMA VAL process resides in:1- the use of hydrometallurgy2- alkaline treatment implementation (highly selective) for zinc and mercury3- electrochemical recovery of high quality products.4- the recycling of all the battery components (zinc, mercury, manganese dioxide, stainless steel) ·5- low operating and investment costs.The process consists of physical classification, mechanical dismantling, hydrometallurgy and electrochemistry. The purpose of the demonstration plant in FALAISE (Calvados - France) is to define the technical and technological parameters of an industrial unit for the treatment of 2400 tonnes per year of used batteries."

Jan 1, 2000

By Bradford C. Wesstrom

The extraction of metals from Copper Refinery Slimes may involve many different processes. This paper describes the use of pressure leaching for decopperizing of copper refinery slimes at the El Paso Refinery. Process equipment will be described, along with the process chemistry, unit operations and unit processes associated with the decopperizing process. Copper contained in the raw slimes ranges from 15-35%. After autoclaving less than 1 % copper remains.

Jan 1, 2000