Search Documents

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By C. Özgen Karacan

Methane emissions from the active face areas and from the fractured formations overlying the mined coalbed can affect safety and productivity in longwall mines. Since ventilation alone may not be sufficient to control the methane levels on a longwall operation, gob vent boreholes (GVB), horizontal and vertical drainage boreholes, and their combinations are drilled and used as supplementary methane control measures in many mines. However, in most cases, the types of degasification wellbores chosen are decided based on previous experiences without analyzing the different factors that may affect this decision. This study describes the development of an expert classification system used as a decision tool. It was built using a multilayer perceptron (MLP) type artificial neural network (ANN) structure. The ANN was trained using different geographical locations, longwall operation parameters, and coalbed characteristics as input and was tested to classify the output into four different selections, which are actual degasification designs that US longwall mines utilize. The ANN network selected no degasification, GVB, horizontal and GVB, and horizontal, vertical and GVB options with high accuracy. The results suggest that the model can be used as a decision tool for degasification system selection using site- and mine-specific conditions. Such a model can also be used as a screening tool to decide which degasification design should be investigated in detail with more complex numerical techniques.

Jan 1, 2009

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

By George Burke

"Many soil mixing methods have evolved over the years, but the Trench Cutting Re-mixing Deep method (TRD) was developed in Japan, circa 1993, to construct continuous uniform cutoff walls, without the need for an open trench. TRD mixing has been used on over 300 projects in Japan for excavation support, groundwater barriers, liquefaction mitigation, soil improvement and pollution containment. To date, TRD mixing has been used on only three projects in the United States: a test cell in Long Beach, Calif., for seawater intrusion barrier in 2004; a groundwater barrier at a wastewater treatment plant in Lincoln, Calif., in 2005; and presently at Herbert Hoover Dike surrounding Lake Okeechobee in southeastern Florida.The most notable benefits of TRD are its abilities to overcome difficult geology, such as layered rock and dense cobbles and gravels that hinder other soil mixing methods, and to create extremely high-quality walls. The method is ideal for situations in which access precludes the use of more traditional methods due to spoil control, such as waterways and congested urban environments or subsurface obstruction/difficult ground. Spoil disposal is minimized since TRD mixes the soil in place.TRD mixing has a horizontal continuity advantage over traditional multi-auger deep soil mixing (DSM) systems. Because DSM systems create walls by overlapping soil-cement columns, the auger may be deflected by difficult ground, and gaps are possible. Gaps may also occur when constructing an exceptionally deep wall due to the possibility of auger deviation from its required vertical alignment.The method also has a homogeneity advantage in layered soils. Because DSM constructs columns by rotating the defined length mixing tools up and down the soil profile while injecting binder, strength and permeability in each layer will vary. The TRD method vertically mixes the entire profile and core samples show highly uniform strength. It is most cost-effective in deep difficult ground such as layered rock or dense cobbles and gravels."

Jan 1, 2009

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By J Kinal

Plant trials are at the best of times difficult to perform; given variations in the ore, operating practice and economic constraints placed on a plant. Testing grinding media at industrial scale adds a further level of complexity that needs to be accounted for.Laboratory test programs consistently demonstrate that altering the grinding chemistry through the application of inert grinding media has the potential to provide significant metallurgical benefit. However, prog- ressing from laboratory testing to industrial trial is often an agonisingly slow process that can lead to inconclusive results which raise more questions than give answers. There are many factors that need to be considered when conducting plant trials aimed at demonstrating the impact of inert grinding media on metallurgical performance. The decisions (or lack thereof) made during the planning stage can heavily impact on whether a statistically meaningful result is achieved. Various factors such as how the trial is conducted (dumping or purging the charge); the circuit configuration; collection of the right data; and even the human factor will affect the outcome. The authors will use examples to demonstrate the importance of proper planning and controlled operation on grinding media plant trials.

Jan 1, 2009

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) slip along steeply dipping faults and (2) fracturing of strong strata above, or below, the coal seam. Both failure modes produce dynamic or ?shock? loads on the perimeter (roof, rib, floor) of mine openings. Special consideration should be given to these failure modes in planning of deep coal mines since their occurrence is not within the professional experience of many contemporary workers, and their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By Wade Edward Speer

The Hiddenite District of Alexander County, NC has produced some of the world?s finest large emeralds since the first one was discovered 134 years ago. In fact, North America?s largest emeralds come from the district, making this one of the continent?s most unique gem deposits. In addition to emeralds, the Hiddenite District is also famous as the discovery site for the rare spodumene mineral hiddenite, first identified in 1881. Nowhere else in the world do these two minerals naturally occur together. The emeralds are a unique color variety of beryl (Al2Be3Si6O18) with trace amounts of Cr+3 and V+3 substituting for Al+3. The hiddenite (LiAlSi2O6) crystals also exhibit emerald green color due to traces of chromium. Consisting of three large deposits and numerous prospects, the district encompasses an area of 10 km2 (4 sq miles) centered on the small town of Hiddenite. Operations at the Adams, Ellis and North American Emerald Mines properties have been productive at irregular intervals since the 1880s. Currently, only the North American Emerald Mines property is being mined on a regular basis. Recent activity there has exposed a 3-hm2 (7.4-acre) pit with depths of 25 m (82 ft) that provides the best exposures of unweathered bedrock seen in the district in more than 120 years. Although no official records exist, public and private data indicate that the production of the entire Hiddenite District from 1880 to 2007 is about 70,000 carats of emerald and 20,000 carats of hiddenite. The bulk of the emeralds came from the North American Emerald Mine property (NAEM, formerly known as the Rist Mine) where sustained mining replaced the previous sporadic prospecting in 2000.

Jan 1, 2009

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By George Oprea, Tom Troczynski, Joe A. Rigby, Waiman Lo

The refractory lining of the tuyere line in Peirce Smith converters have usually much shorter life in service than the rest of the lining, above or below it. There are already recognized chemical, thermal and mechanical factors which contribute to the wear of the lining. Our study presents the experimental results on microstructural changes occurring on these tuyere line bricks in a nickelcopper converter. The experimental bricks, after use at the tuyere line, were investigated using SEM/EDS and XRD techniques, to identify the mineralogical changes due to interactions with the nickel-copper matte or fayalite type slag at the process temperatures. The microstructural changes were correlated with physical and mechanical properties of the brick before and after use and a wear mechanism was suggested. Although the matte does not theoretically react with the mineralogical components of the brick, a partial oxidation of the Ni-Cu sulphides was identified using a line analysis by SEM/EDS in the densified layer at the hot face, which allows for mineralogical changes at the matte-refractory interfaces, with a high probability of microcrack formation due to the thermal cycling during use. These microcracks were also identified to open through inter-granular fractures parallel to the hot face, which appeared to be the main cause of lost lining during use. The reactions between the fayalite slag and refractory brick could eventually play a role in chemical dissolution of the brick only in the superficial layer at the hot face, as no slag components were identified deep into the brick.

Jan 1, 2009

By Roy H. Grau

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines whose entries are at least 93m2 (1,000 ft2). The ventilation of large-opening mines is unique compared to other types of mines because (1) it is challenging to keep airflow velocities high enough to effectively remove or dilute airborne contaminants because the entries are so large, (2) large air volumes can be moved through the mines with little static pressure drop, and (3) stoppings that are used to direct ventilation airflows are costly to construct and to maintain. The research results suggest that the ventilation of large-opening mines is improved significantly by incorporating ventilation planning into the mine planning process, using propeller fans to direct airflow, developing new stopping materials and construction methods, and using long pillars to eliminate crosscuts where possible.

Jan 1, 2009

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By Scott Giltner, Allan Koski

Blasting is one of the lowest cost yet most critical parts of the mining cycle. This paper discusses the findings of an audit conducted on the blasting operation at an iron ore mine. The purpose of the audit was to review current blasting practices in order to identify opportunities for production/cost improvements. The approach taken in the audit was to observe general blasting practices, their related downstream effects and to compare current procedures to established best practices.

Jan 1, 2009

This paper describes the development of an approach to sustainable development for application at the feasibility study stage for a proposed bauxite mine near the community of Aurukun, south of Weipa on the western coast of Cape York Peninsula, Queensland, Australia. The general environment for development was complex in all dimensions. In particular, the socio-demographic profile of the Aurukun community (population 1200) characterised it as being amongst the most disadvantaged communities in Australia. The traditional owners of the area, the Wik and Wik-Way people, were at the forefront in the efforts of Indigenous people in Australia to secure land rights over the past 30 years, and they had previous experience negotiating an Indigenous Land Use Agreement (the Western Cape Communities Coexistence Agreement) with Rio Tinto Alcan, the operators of the Weipa bauxite mine. Through this they had shown a well-founded sense of entitlement with respect to the development of resources on their traditional land. The Queensland State Government had recently cancelled an existing mining lease over the bauxite resource as the holder of the tenement had not fulfilled the terms of a development agreement that had been in place for 30 years. The Government was anxious to avoid any future æbankingÆ of the resource, and had decided to offer tenure to the resource on an international competitive basis, subject to the requirements of the Commonwealth Native Title Act 1993. This would require a negotiation process with traditional owners and potentially involve companies with whom the traditional owners had no existing relationship (typically developed during the projectÆs exploration phase) and who possibly had no project development experience in Australia. As well, the State Government envisaged an approach to development that drew on the significant work that industry and other stakeholders had undertaken over the previous ten to 15 years, commencing with the mining, minerals and sustainable development (MMSD) process. This work was aimed at rectifying acknowledged deficiencies with industry recognition of stakeholder interests, in particular with respect to environmental management and socioeconomic development. The approach adopted aimed to define the strategic community interests and sustainable development outcomes to which the development of the resource would be expected to contribute, and to embody these within an easily usable management structure that could be applied to each stage of project development from feasibility study through to mine closure. The logical framework (AusAID, 2006; ICMM, 2005) was the management tool utilised to order the identified interests and desired outcomes. The structure included components aligned with the key areas of development interest expressed by the community, and the initial baseline sustainable development plan (SDP) developed established component objectives, outcomes, indicative outputs and activities for the feasibility stage of the project. This established an objective framework to guide potential bidders when developing their response to the State GovernmentÆs Request for Proposal. The paper will describe the evolution of the competitive process and the parallel process for development of the SDP. While the institutional environment was politically and socially complex, the use of simple visual representations of the environment and the analysis and ordering of issues, objectives and criteria through methods such as stakeholder analysis and the logical framework approach, enable the development of a dialogue on the contribution that the development of a mining project can make to sustainable community development, and for the development of an agreed program of community support to capture the contribution. The use of the logical framework was found to have good functionality for plan development. Achieving plan outcomes though, is highly dependent on the skill of key project personnel in facilitation, team building, conflict resolution and leadership, as well as their ability to influence the behaviour of key stakeholders with the capacity and authority to require the integration of local economic development criteria in to key project development decisions.

Jan 1, 2009

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia, about 50 km north of the town of Southern Cross. Ore is trucked from three geographically isolated sources to the crusher at Koolyanobbing, where it is blended before and during crushing. Lump and fines products are produced and railed to Esperance for ship loading and export to Asian customers. CNR is examining alternative processing paths, from mining to ship loading, with the aim of improving efficiency and reducing costs. Modifications to the system must be consistent with potential future expansions and maintain the low inter-shipment grade variability on which CNR prides itself and has built a strong relationship with its customers. In searching for the optimum process design, many options from mine face to ship loading must be evaluated and compared. Pilot plant studies are infeasible, while complex mineralogical interactions, competing goals and numerous possible system configurations limit the applicability of theoretical analysis. It was therefore concluded that simulation modeling would provide the confidence to take the next step into production trials. This paper describes techniques applied at CNR to simulate grade variability resulting from potential process design changes. The simulation models are easily run Excel-based modules, with each module representing a different part of the process. The modules use extensive Visual Basic macros driven by Excel's user-friendly interfaces. Presentation of the results is enhanced by Excel's excellent graphical capabilities. The simulation software stores and graphically presents time-stamped data from a run, enabling detailed analysis of different process configurations. Final success of a simulation run is measured by inter-shipment variability (standard deviation and process capability) and in-process ore tonnages. Meaningful results from the simulations require the initial input data contain the same correlations present in the real production environment, between the mineral components, production linkages and across time. The data also have to allow simulation of potential changes to mining method and introduction of new pits into the blend. Mining data from the real operations under study are therefore used, with average grades and variability adjusted to match potential future development proposals. It is also necessary to filter out medium and long-term variations from the production data as this variability is best controlled through the conventional medium to long-term mine planning process, not by the process design being studied. The filtering was carried out using a Fourier transform technique, which is described.

Jan 1, 2009

By Michael J. Marinigh

"Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable.In converting furnaces which have tuyères such as the Noranda Reactor and the Teniente, Peirce- Smith and Hoboken converters, efficient tuyère line management is critical to optimizing blowing rates, increasing refractory life, and improving safety.This paper will describe recent improvements made to equipment used for tuyère punching, tuyère silencing, tuyère pyrometry and refractory drilling of tuyères and how the proper application of the equipment can lead to operational and safety improvements."

Jan 1, 2009