Search Documents

By Don W. Dotson

In 1962, Kondner prepared several papers dealing with hyperbolic stress-strain response of cohesive soils. The following year, Brinch Hansen proposed 80% and 90% failure criteria for stress-strain behavior of cohesive soils. Fellenius was instrumental in popularizing these failure criteria for pile load tests and offered a direct solution equation for the failure load according to the 80% failure criterion. Since the 90% Criterion has been incorporated into the International Building Code, equations for the direct solution of the failure load at the 90% Criterion would be useful to practicing engineers. This Technical Note supplies the derivation methodology for the 80% Criterion and provides expressions to determine the load and deflection at failure for the 90% Criterion.

Aug 1, 2013

Waste rock extracted from a mine is typically stored nearby on the surface. Such waste rock piles must be designed to ensure their geotechnical and geochemical stability during the mine operation and after closure. The optimal construction of a pile requires detailed planning. Deposition should involve benches of limited height to control the global slope angle, based on the long term factor of safety. It can also be advantageous to compact the top of each bench and to give the surface an outward inclination to control water flow by limiting infiltration and favoring lateral diversion. When part of the waste rock contains reactive minerals, it is also deemed necessary to use selective placement with the non-reactive portion to prevent direct exposure to natural conditions. The construction must be well documented, and include data from the monitoring program. These and related aspects are presented and discussed in the paper.

Aug 1, 2013

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By Ibrahim Ocak

The prediction of machine utilization time and determining machine performance plays an important role in scheduling and planning tunnel excavation and data base created serve a major role in further applications. In this study, the construction methods of two twin tunnels situated between Basak Konutlari station and Istoc station are summarized. Geology in the study area is composed of fill and weak rock, respectively starting from the surface. The tunnels of 5.6 km in length were excavated with two different earth pressure balance machines (EPBM). Excavation diameters of the EPBMs were 6.564 m. The performance of the machines are analyzed and compared in order to accumulate data for further applications in similar ground conditions in Istanbul. The distance between two twin tunnels is 14 m from center to center and the EPBM in the one tube was almost about 100 m behind the other tube. Segmental lining with 1.4 m of length and 30 centimeters of thickness were used as final support. The overall performances of the two Lovat TBMs are found to be respectively as; the best daily advance rates 30.8 m/day and 30.8 m/day, the best weakly advance rates 115.0 m/day and 153.9 m/day, the best monthly advance rates 388.7 m/day and 400.5 m/day. Total waiting and maintenance times were 25.2 and 16.7 %, respectively.

Aug 1, 2013

By K. Cybulski

Coal dust explosions still remain the main hazard in the coal mining sector, notwithstanding their relatively wide recognition compared to other hazards and the development of effective methods of prevention. Coal dust explosions are still the cause of numerous catastrophes, often leading to fatalities. Fortunately, they rarely occur, and it is for this reason that their hazardous impact is often underestimated. This problem in Poland is being exclusively solved by the Central Mining Institute, Experimental Mine Barbara. Here, basic research on the phenomenon of coal dust explosions and prevention methods is carried out, as well as investigations into the causes and circumstances of past accidents. After 15 years of no coal dust explosion accidents in Poland (1987?2002), a few coal dust explosions have recently occurred, with tragic consequences. These events have taken place not only in hard coal mines, where the presence of dangerous coal dust is the result of common production cycle, and safety measures against coal dust explosions are subject to specific regulations, but also in coal-fired power plants. This is of special concern because prior to 1987, such accidents had been been reported only for coal mines and not for coal-fired power plants. In recent years, two dust explosions occurred in Polish power facilities: the Dolna Odra and Turow power plants. In both cases, coal dust explosions occurred in the fuel supply system, but biomass dust was also involved. The explosions caused significant damage to the systems and buildings. This paper gives description and schematics of the regions of catastrophic coal dust explosions that have occurred in recent years in Poland, as well as the results of post-accident investigations, presenting the coal dust explosion hazard at the accident scene The results specify in detail the state of safety measures against coal dust explosions in light of the relevant regulations in force, including amount of deposited coal dust, content of incombustible matter in coal dust, free moisture content in coal dust, state of coal dust explosion safety zones, and state of explosion barriers. The conclusions from the site inspection and post-accident investigations presented enable us to determine locations of explosion initiation, probable ignition sources, range of explosion flames, and explosion barrier performance. A complete elimination of coal dust explosion hazard at the site of dust deposition is practically impossible to achieve. Similarly, a total elimination of ignition source, which may be related to the occurrence of other natural hazards, equipment malfunction or human errors, is impossible. The examples of tragic events that took place in Polish coal mines and coal-fired power plants highlight shortcomings and mistakes made in terms of assessment and prevention measures taken against the coal dust explosion hazard.

Aug 1, 2013

The concept and practices of co-extraction of coal and methane have emerged in recent years to improve coal mining safety and productivity, utilise methane resources, and reduce fugitive emissions in environments that involve multiple coal seams with low gas permeability. The system of co-extraction integrates two previously separate operations of coal extraction and methane drainage. The coal mining operation reduces the coal seam gas pressure and creates strata fractures that enhance gas migration and capture from mine workings and surrounding coal seams. An effective methane drainage operation produces a consistent and quality clean energy product and, at the same time, reduces the methane concentration in underground workings and the methane content and pressure in the adjacent coal seams. This is a significant benefit in preventing gas explosions and outbursts, and promotes a safer and more productive coal mining environment. In addition, the co-extraction with enhanced utilisation of coal mine methane directly leads to a reduction in greenhouse gas emissions. Presented in this paper are key results and outcomes of a major Asia Pacific Partnership project carried out from 2008?2012 by the Commonwealth Scientific and Industrial Research Organisation in collaboration with Huainan Mining Industry (Group) Co. Ltd., to develop and demonstrate advanced technologies at Pansan mine, Huainan, that promote the concept and practices of co-extraction of coal and methane. A comprehensive approach was adopted to assess fundamental strata and coal seam methane conditions during mining, and optimise mining sequences and coal mine methane capture systems. The project has not only demonstrated a practical approach and procedures of advanced co-extraction of coal and methane systems but also delivered significant benefits and outcomes in improved mining safety and efficiency, increased methane capture and utilisation, and reduced fugitive methane emissions at the Pansan mine. The total mine gas drained increased from 25.36 Mm3 in 2007 to 47.0 Mm3 in 2011, and the mine gas utilisation increased from 4.94 Mm3 in 2007 to 21.15 Mm3 in 2011. The improved methane capture resulted in reduced coal and gas outburst risks and methane concentration levels at the mine workings, provided a safe working environment for coal production, boosted the mining efficiency, and eliminated methane related incidents over the last few years at Pansan mine.

Aug 1, 2013

By J. Kang

Large-scale land reclamation has been undertaken in Singapore since the 1960s. In the early years, the fill materials excavated from the hills. In recent years, sea sand is the main source of the fill materials. The contractors used to import the sea sand from the neighbouring countries such as Indonesia. However, in early 2000, the sea sand import from Indonesia and Malaysia was banned. Cambodia, Myanmar, and Philippine therefore became the alternative sources for sea sand. Distance between the jobsite and these countries is over 1,200 km, and transporting sea sand from these areas became a critical issue that could affect the contractor?s performance. Figuring out the right combination of transportation means for a longdistance sand transportation would be challenging because of uncertain situations. We developed a stochastic simulation model, using ARENA, to figure out the right quantity of small-size barges, bulk carriers, and loading/unloading equipment, which could help project managers yield the most production for sand transportation. This paper presents how we developed the simulation model, how it was applied to figure out the optimum combination among various size barges, different bulk carriers, and various types of loading/unloading equipment, for the sand transportation project in Singapore.

Aug 1, 2013

By L. Tikasz

The primary purpose of ore hauling model studies is to capture the variability of the ore delivery ? stockpiling process in order to improve the estimation of equipment capacities and achievable throughputs. The operation of a mine-to-site ore delivery system is the subject of a number of challenges. Typically, ore is hauled by a given combination of trucks, conveyors and trains. In addition, ore loading, ore transferring to another means of delivery, stockpiling, reclaiming, and further deliveries involve many other types of equipment. The concurrent operation of all these units is scheduled; nevertheless, they are subject to planned maintenance and random breakdowns. To support our engineering design work on ore hauling operation, discrete event type models were built for each specific task. Then, due to recurring demands, an ore hauling library was gradually compiled. The now available model library allows fast and efficient simulation of various mine-to-site hauling arrangement, adaptable to various mining and mine construction operations (e.g. bauxite, iron ore, copper ore and coal).

Aug 1, 2013

By J. Y. Kim

This paper presents a novel action recognition method for observing human workers using interactions between actions and related objects on an internal construction site. This method can be used to measure work rates for labour productivity monitoring. This monitoring is critical because the performance of a construction project is significantly impacted by labour productivity. However, construction sites are generally crowded with a large number of workers and objects. Such congestion disrupts the accurate, automatic recognition of construction workers? actions. This congestion is one reason that existing automatic action recognition studies of construction areas mainly focus on workers? actions themselves. However, the crowded conditions mean that sites could offer a great deal of clues that could be used for automatic action recognition. According to psychological studies, interactions clearly take place between human actions and related objects, such as between hammering and a hammer. Humans use these interactions to recognize actions or objects more accurately. On the construction site, workers, materials, tools, and equipment are carefully planned out ahead of actual construction. The categories of workers and objects are pre-defined and, as noted, specific interactions define relations between worker actions and objects. In this paper, the interactions are limited to human workers and their hand-held objects. Action recognition results can be combined with hand-held object information to improve recognition accuracy. With the limited interactions, experiments in this paper show a significant improvement in action recognition. This paper describes the utilization of these interactions to improve construction action recognition accuracy based on human skeleton data and 2D color video from Microsoft KINECT sensor.

Aug 1, 2013

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By George Carico

Research and related demonstration projects are being conducted in West Virginia on both existing and former coal surface mine lands to determine potential post-mine land re-use options that offer the greatest likelihood of future benefit and success. Examples of projects include renewable energy considerations that incorporate solar, wind, and/or biomass options, and contain components designed to educate business, government entities and the local community on renewable energy options and potential opportunities Multiple property re-use options are being researched and evaluated, based on site-specific conditions and characteristics, including infrastructure, local community needs and regional economic conditions. Re-use options being explored include innovative uses and needs, such as specialty housing, unique business and industrial needs, and an extensive variety of recreational and small business opportunities that best fit the specific needs of the local community and regional economic structure.

Aug 1, 2013

By P. Klossek

It is estimated that China accounts for 94% of the world supply of rare earths (Roskill, 2011). This fact, together with the impact of China?s export policy, poses a substantial risk to the security of the rare earth supply as well as a rare earth price risk. This situation has motivated an increase in the number of rare earth projects under development, i.e., there are currently more than 440 worldwide (Technology Metals Research, 2012). However, economically and environmentally acceptable processing technology to produce tradable products from rare earths (e.g., separated rare earth oxides) is not freely available on the market at the moment. In this respect, a lot of research and development has been initiated on this topic, in academia as well as in industry. Using a proprietary model and scenario-based analysis, we studied the impact that the development of rare earth processing technologies would have on the rare earth market and the economic feasibility of rare earth projects mentioned before. The analysis showed that this impact varies depending on the technology type (e.g., technology can affect project production volume, cost structure or both) and the legal context of the invention (e.g., free or limited by patenting availability of a new technology). The effect of a technology which influences project production volume is not the same as of a technology which changes project cost structure. The impact of a patented processing technology differs from the impact of a processing technology which is freely available on the market. In the case of a new technology which is limited by patenting, its impact depends on the market position (?producing?, ?next-coming?, or ?not producing? project) of the patent holder. The paper contributes to existing research by studying the dependence of the expected micro- and macroeconomic impact of rare earth processing technology developments on the properties of a new technology (e.g., costs, legal framework etc.). By this means, the paper adds to existing knowledge and attempts to make the rare earths market more transparent and predictable from a perspective outside China.

Aug 1, 2013

By D. Campbell

Mining activity is increasing in northern boreal and subarctic regions of Canada. This is the case in the far north of Ontario, especially in and near the Hudson Bay Lowland (HBL). De Beers Canada opened the Victor diamond mine in the centre of the HBL in 2008, and advanced exploration and impact assessments are occurring to the west in the ?Ring of Fire? for ferrochrome, nickel/copper, iron/ vanadium and platinum-group elements, making it one of the richest mineral finds in Canada in recent years. However, the HBL is also a near-pristine, sensitive environment. Its peatlands forms the third largest wetland in the world and are globally important stores of terrestrial carbon. Human populations in the region are sparse, consisting almost entirely of First Nations communities. Local First Nations also have a strong land ethic and greatly influence mining developments. Through formal agreements, they have insisted on a gold standard for environmental management, including a small mine footprint and the return to representative native ecosystems after mine closure. However, knowledge on the revegetation of subarctic and northern boreal ecosystems is limited. Here, we are conducting research at the Victor mine to develop gold standard protocols for the revegetation of disturbed peatlands and mine waste uplands and present a summary of results. We first tested existing protocols for peatland restoration from southeastern Canada. We collected peat-forming plants from nearby muskeg, spread them sparsely over disturbed peatlands and applied a light phosphate fertilizer, but unlike southern protocols, no mulch appeared to be required to produce a representative cover of peat-forming plants within three years. A bigger challenge is the reclamation of uplands made of mine waste back to representative ecosystems. We first characterized reference conditions for uplands in the HBL, which are scarce in the region. Nearby natural uplands were divided into two classes, interior uplands and uplands along river valleys. Multiple parameters were examined at these sites including soil development, bulk density, soil chemistry in the rooting horizons, plant cover by stratum, plant species composition and dead wood. The mean condition and, more importantly, the range of these parameters allow us to set broad targets for progressive reclamation, which will facilitate success. Finally, we characterized local upland plant species through their functional traits to determine their likely abilities to colonize, grow and contribute to ecosystem processes. A classification of species by these simple functional attributes will help restoration managers to select candidate species to meet different goals at different successional stages (i.e. good versus poor dispersers or establishers). Research into these protocols remain in the early stages, but show promise that gold standards can be achieved to ensure that mining wastes can be reclaimed to productive ecosystems.

Aug 1, 2013

By K. Chotruangprasert

This paper explores Global Reporting Initiative (GRI) reporting practices within the mining industry. Specifically, this paper investigates how and why a mining company makes voluntary reporting decisions to include the GRI indicators that may be considered ?negative? to the company?s reputation. Due to the voluntary nature of the GRI Guidelines, a GRI adopter is not legally obligated to report every GRI indicator. Not surprisingly, empirical studies that evaluated the extent to which companies? sustainability reports meet the GRI requirements (Guenther, Hoppe, & Poser, 2006; Morhardt, Baird, & Freeman, 2002; Samy, Odemilin, & Bampton, 2010; Skouloudis, Evangelinos, & Kourmousis, 2009) have found that reporting practices of the companies under their studies are well below the standards reflected in the GRI Guidelines. An influential study by Clarkson et al (2008) uses economic-based and socio-political theories to explain variation in companies? environmental disclosure. They have found that, as predicted by economic-based theory, superior environmental performers disclosed more ?hard? (i.e. verifiable) environmental information. Inferior environmental performers are found to disclose more ?soft? (i.e., not easily verifiable) claims, which is consistent with socio-political theories (Clarkson, Li, Richardson, & Vasvari, 2008). However, this study and the existing literature do not adequately explain why a company may act in a way that cannot be explained by economic-based and socio-political theories, for example, why it would report some negative soft data that it is not required to report. This paper intends to address this literature gap. GRI reporting by a Canadian mining company, which I would like to call ?Company C?, is used as a case study for this paper. Company C was selected for this research because in addition to ?positive? information, its GRI-based sustainability report also includes both hard and soft ?negative? information such as grievances. Research methods include interviewing Company C?s employees who are involved in preparing GRI reports and reviewing documents prepared both by the company and by external parties. I find that integrative social contracts theory (ISCT) offers a valuable explanation to Company C?s reporting practices. From the ISCT perspective, Company C?s management appears to feel that the company is obligated under social contracts to be transparent. Therefore, Company C disclosed both positive and negative social and environmental information to the public because the management appeared to think that it is the right thing to do. At the same time, being transparent about the bad news gave the company an opportunity to conclude that it had done something to avoid future occurrence of the negative incidents. Therefore, I propose that, in addition to the economic and socio-political theories that are more often used in literature, insights from ISCT are instrumental in improving our understanding of the corporate non-financial reporting practices phenomenon.

Aug 1, 2013

By Bahaa Hussein

Considerable number of methods and procedures has been introduced for trending and progress reporting of engineering, procurement and construction projects. This paper introduces a novel method, designed to augment the set of indices for measuring schedule performance. The concept behind the developed method is to provide early warning by dynamically evaluating the schedule cumulative impact of construction projects. The proposed method is designed to highlight the gradual deterioration in schedule status resulting in a cumulative impact due to the aggregation of small delays encountered during the execution of non-critical activities, and can be used as an add-on utility to existing software systems that perform CPM scheduling. The proposed method is based on a developed formulation for quantification of the Schedule Compression Index, which takes into consideration the remaining project activities durations. The index is developed based on periodic comparisons of ?Current Schedules? and the project ?Baseline Schedule? using the summation of the remaining activities durations. A numerical example is presented to demonstrate the application and capabilities of the developed method. It is expected that the developed index together with other schedule performance indices would be of value to decision makers and members of project teams.

Aug 1, 2013

By A. P. Sasmito

It is well known that underground miners are exposed to one of the most dangerous working environments on earth. As mine delve deeper, the geological factor, mine position and climate condition as well as heat generation from mining machine give rise to the mine operating temperature. This, in turn, has an adverse effect on the environment and thus leads to higher operating costs. Careful estimation and design of air flow rate, spray system, cooling load and additional ventilation auxiliary equipment are of importance to ensure safety, comfort and productivity whilst maintaining low operating cost. A computational fluid dynamics simulation approach is employed to examine underground mine ventilation in a 36 m cul-de-sac of tunnel of coal mine. The model predictions in the turbulent range were validated by comparison with published data. Different turbulence models were tested to select one that yields adequate accuracy and is computationally efficient. Effects of the following parameters are evaluated: tunnel geometry, air flow rate and inlet air temperature. The objective of the simulation is to arrive at an optimal strategy for ventilation and thermal comfort at low cost.

Aug 1, 2013

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

From 1999 to 2008 rock related accidents accounted for 75 fatalities, nearly 6,000 injuries and almost 14,000 incidents (Pappas and Mark, 2011). Clearly this shows that rock related safety on coal mines remains a serious issue and more effort is needed to address this hazard. This paper reviews support design considerations and monitoring needed to improve rock related safety in room and pillar coal mines in the USA. From the present study design considerations continue to evolve and improvements in technology and a better understanding of failure mechanisms and methods to prevent these failures from occurring are in place. At first glance, the design of safe and efficient underground openings appears simple until the designer begins to realize the complexities and variability of geometries, geology, loading and stress influences, support designs and other factors such as corrosion and economics. Ultimately the goal of all designs is to ensure that it can be completed safely, last for the duration of the design life and it is economically feasible.

Aug 1, 2013

By Greg Ford

Each year, companies spend millions of dollars on safety training and on safe equipment, money that is generally well spent. Despite that, we still make mistakes. What happens if the mistakes are made not because of inadequate training, but because we are hard-wired to act in a certain way? If you read any of the ?Because of Human Error? text boxes in this document, situations like these may look familiar in your own workplace. ?The issues of risk, health, safety and the environment are getting more attention now than ever before, at all levels of the organization,? said Calvin Price, vice president of Global Health and Safety at LNC-Lavalin Inc., a company with 21,000 workers worldwide. Most would agree with Price that attention to safety is increasing because responsible companies care about their workers and the workers? colleagues, families and communities. However, cynics might say that the safety spotlight is powered by the corporate bottom line. Direct costs created by workplace injuries total $51.8 billion annually and include workers? compensation payments, medical expenses, civil liability damages and litigation expenses. This sum represents a staggering one quarter of each dollar of pretax corporate profits. Indirect costs may run as much as 20 times the direct costs of on-the-job accidents and illnesses. Examples of indirect costs include training replacement employees, investigating the accident and implementing corrective measures, lost productivity, repairing damaged equipment and property, and costs associated with lower employee morale and absenteeism. What?s interesting is that up to 90 percent of incidents are due to human error, not faulty equipment or other factors.

Aug 1, 2013