Search Documents

"Coupon testing has been used to investigate stress corrosion cracking (SCC) of rockbolts in a laboratory based experimental program. This program has focused on the use of ASTM G39 three- and four-point bent beam coupon specimens, immersed in an acidified sodium chloride test solution containing hydrogen sulfide. The specimens were loaded to a range of stresses from zero, to just above the materials yield strength. It was found that only specimens above an applied stress of 580MPa failed by means of SCC, showing that rockbolts loaded to near their yield strength may be susceptible to SCC in-situ.INTRODUCTIONStress corrosion cracking (SCC) is a failure mechanism that affects material through the growth of hairline cracks when exposed to a corrosive medium while under stress (Jones and Ricker, 1999). SCC has been found to affect rockbolts in the Australian underground coal mining industry and has the capacity to cause the catastrophic failure of ground support systems, potentially leading to falls of ground in underground excavations, injury or death to mine personnel, damage or loss of equipment, and loss of productivity through the loss of roadway access (Crosky et al, 2002).Coupon testing utilises small scale samples that are intended to be indicative of the behaviour exhibited by a material in-situ (ASTM G39). The small scale, and usually high surface area to volume ratio of coupon specimens mean that they corrode at faster rate proportional to their mass, greatly reducing testing times. The small scale of the specimens allows them to be more easily prepared and handled, loaning them to mass manufacturing techniques.A previous study conducted by Vandermaat et al (2012b) into the use of three- and four-point coupon testing in-situ in an underground coal mine failed to result in SCC of the specimens. This paper serves as a follow up laboratory investigation in order to understand why these specimens did not fail. Previous studies into the SCC in rockbolts carried out by Gamboa and Atrens (2003) determined that rockbolt steel has a critical stress threshold of approximately 90% of the material ultimate tensile strength (800-900MPa). This study will focus on this critical stress threshold as a possible explanation for the lack of failure in the in-situ specimens (Vandermaat, 2012b)."

Jan 1, 2015

By H. Nagel, A. P. Schissler

"INTRODUCTION Anadarko Petroleum Corporation (Anadarko) owns a region of oil shale properties acquired as part of the original Union Pacific Land Grant of the 1800’s in southern Wyoming. These holdings are greater than 2 million acres and occur throughout the Green River Formation in southwestern Wyoming. One area was prioritized for further study by Anadarko Minerals called the Kinney Rim in the Washakie Basin due to low environmental impact, proximity to infrastructure, high ore grade, and low mining cost. The area is a low-overburden oil shale resource that can be developed using surface mining methods, processed by conventional surface retort, and placing waste rock disposal back on the bench for a design capacity of 10,000 barrel per day. The purpose of this papers is to present the results of environmental analysis and timeline, the mine plan, and surface ore processing to offer a resource-ready energy source.Mineral rights for the Kinney Rim area are owned by Anadarko, the United States Bureau of Land Management (BLM) and the State of Wyoming. Mining of oil shale for this study targets Anadarko owned mineral resources.GEOLOGY The study area is in the Green River and Washakie Basins in western Wyoming. The host geologic member is the Laney Oil Shale. Figure 2 illustrates the Laney shale within a generalized lithologic cross section.OIL SHALE LEASING The proposed Kinney Rim oil shale mining project is located in an area dominated by a 1 square mile checkerboard landownership pattern with every other section typically administered by Bureau of Land Management (BLM) and Anadarko. Surface and mineral ownership is a split estate legal entity. The immediate Kinney Rim mine plan is all on Anadarko sections."

Jan 1, 2015

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By M. F. Ameur, M. Habak, H. Aouici, M. Kenane

Present study interest by aluminium alloy (Al 7175-T5173) drilled without cooling fluid. The influence of the machining parameters (spindle speed and feed rate) on the holes quality was analyzed. Drilling tools are made of carbide (WC); high speed steel (HSS) and TiN coated carbide (WC-Ti).The Experiment design was reinforced by the application of statistical analysis of variance (ANOVA).The results show that the thrust force is influenced principally by the spindle speed and feed rate. Though, both feed rate and tool materials have statistical significance on the surface roughness. In addition, the objective of correlations between spindle speed and feed rate with the evolution of the machining parameters was established. These correlations were obtained by quadratic regression using the response surface methodology. Finally, useful to select optimum values of drilling parameters, that would minimize thrust force, torque, cutting temperature and surface roughness.

Jan 1, 2015

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By I. Ruiz Bustinza, L. F. Verdeja, Daniel Sbarbaro, R. Parra, J. Mochón

The oxidation of sulfides is a complex process involving gaseous products and intermediate species given rise to emission and absorption spectra which carry out important information about the reaction process. This information could be used for on line monitoring of pyrometallurgical reactor if the appropriate sensors were available. We present in this paper an analysis of the concept that has been successfully applied in iron and steel making industry, as well on fuel combustion control, where the spectra measurement gives the possibility for online monitoring and automatic control of high temperature processes. This concept has not been widely applied in the nonferrous pyrometallurgical primary production. The design of new sensors is discussed from the analysis of spectra measurements during flash combustion of copper concentrates at laboratory scale.

Jan 1, 2015

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By M. Rizwan

Mine workings are progressing to greater depths as shallow mineral resources are being depleted, and civil engineering projects are nowadays being developed at substantial depths. The threat to tunnel stability posed by rockburst events has increased as a result of these high stress environments. Rockbursts are violent events capable of mobilizing large volumes of rock. In addition to the threat to safety and equipment, rockburst damage can significantly impact on operations, and cause loss of mining production, often the largest cost component of such events. Rehabilitation of such damage requires significant effort and resources. Tunnel walls and roof are usually well supported, but the installation of rock support in the floor is uncommon, particularly in mining environments. In the absence of rock support, floors of the excavations are vulnerable to rockburst damage. New concepts for containing damage of excavation floors by dissipation of the large transient forces using simple techniques or preselected and designed elements of sacrificial floor systems are presented. Two approaches to calculate the demand are presented: estimating load demand by assuming displacement levels and a response modification factor; and using a limit displacement approach to calculate elastic stiffness of the selected elements of the sacrificial support system. The proposed conceptual support systems have the capability of dissipating rockburst energy while retaining sufficient serviceability. It is considered that the concepts presented, for discussion, in this paper are logical and developable into practicable and economic solutions for tunnel floor support in rockbursting environments.

Jan 1, 2015

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li, Donald A. Bruce

"In-situ wet grab sampling and post-installation coring of soil-cement structures are typically carried out for Quality Control (QC) and Quality Assurance (QA) of deep mixing (DM) schemes. Wet grab sampling and testing is used to provide data to indicate that performance requirements are being met during production, in advance of coring, which typically occurs at 28 days or later, following installation. While unconfined compressive strength (UCS) tests from wet grab samples provide good production indicators, industry practice often requires that acceptance criteria of soil-cement structures be based on UCS results from representative core samples.This paper outlines the approach adopted for field sampling and QA/QC testing carried out in highly variable subsurface conditions at a site located in northern British Columbia (BC), focusing on postinstallation soil-cement coring and strength testing for an extensive deep mixing scheme. A discussion on suitable methods of coring soil-cement structures and appropriate selection of samples for testing that are representative of the in-situ soil-cement structures is provided. This paper also discusses the selection strategy adopted for verification of strength and modulus parameters used for design, providing spatial and time coverage, as well as the acceptance criteria implemented, and provides comparisons with published industry recommendations.BACKGROUNDAn extensive deep mixing ground improvement scheme was completed for the development of a Liquefied Natural Gas (LNG) Facility to be located in Bish Cove, BC, Canada. The deep mixing scheme was implemented to treat very weak native deposits in-situ to support two mechanically stabilized earth (MSE) walls up to 20 m (66 ft) high, and their associated bulk earthworks. Within the DM area, the subsurface conditions were highly variable, ranging from deep (up to 21 m (69 ft) thick) deposits of very soft to soft clayey silt to silty clay, overlying layers of dense to very dense gravelly sand to sand and gravel, to compact deposits of silty sand (up to 15 m (49 ft) thick), overlying dense sand and gravel. Bedrock was encountered beneath the granular deposits and generally comprised granodiorite with occasional andesite dykes."

Jan 1, 2015

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

By G. O. Oniyide, H. Yilmaz.

"This paper presents the result of the research done on the effect of temperature on the dilatancy of rocks from the Bushveld Igneous Complex (BIC), where the South African Platinum mines are located. The BIC has higher virgin rock temperature (VRT) than the gold mines of the ‘Witwatersrand Basin Complex’. If the platinum mines advance to ultra-deep levels as the gold mines, since the Merensky Reef has been reported to extend beyond 5km, then the virgin rock temperature at 5 km below surface would be approximately 140oC. Hence, there is a need for the investigation of rock behaviour at high temperatures. Five different rock types (norite, leuconorite, mottled anorthosite, pyroxenite and chromitite) were tested in a 2600 kN servo-controlled multi-purpose triaxial testing machine. The tests were done at a constant strain rate of 5 x 10-1 S-1 and a confining pressure of 10 MPa within temperature range of 20 °C (ambient temperature) to 140 °C. The results show a general strength reduction and increasing dilation angles with increasing temperatures. The results also demonstrate that dilation angle is close to the internal friction angle at lower temperatures; however, they are greater at higher temperatures.INTRODUCTIONMany challenges are faced with increasing depth of mining in underground mines. The most obvious are heat, in-situ stresses and those associated with logistics. Issues related to underground heat have mainly focused on the side effect of heat on workers' health, increasing production costs as a result of higher cost of ventilation. The effect of increasing temperature with increasing depth on the behavior of rock has not been given much consideration. Generally, gold mines in South Africa are deeper than the platinum mines but the latter have higher temperature gradient, which makes the platinum mines to be warmer at similar mining depths. Although the study of the effect temperature on the behaviour of rock can be beneficial to both gold and platinum mines, the focus of the research is limited to the platinum mines because of their higher temperature gradient. Donoghue (2004) stated that the virgin rock temperatures (VRT) and air temperatures increase with depth, due to the geothermal gradient and auto-compression, that is, compression of air by its own weight."

Jan 1, 2015

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

By T. Johnson, K. Lambrych, D. Kelley

Materials for construction of equipment used in hydrometallurgical plants are selected based on a combination of their ability to perform as required in aggressive process environments as well as their cost. As a material of construction, fiber reinforced plastic (FRP) has been shown to provide equal if not improved durability relative to alternative materials such as corrosion resistant alloys at a considerably lower cost. This is particularly true in the case of equipment used in acid leaching processes for copper, cobalt, nickel and rare earth elements. The selection and extensive use of FRP over alloys in new hydromet plant construction in North and South America illustrates this advantage of FRP effectively. This paper will compare corrosion performance and cost of plant equipment fabricated with stainless steel alloys and FRP made with Epoxy Vinyl Ester thermoset resins. Real world case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment.

Jan 1, 2015

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By G. Archibald, M. McSaveney, J. Wartman, M. Yetton, C. Massey, C. Holden, A. Kaiser

"The 2010/11 Canterbury earthquakes triggered many mass movements in the Port Hills including rockfalls, rock and debris avalanches, slides and slumps and associated cliff-top cracking. The most abundant mass movements with the highest risk to people and buildings were rockfalls and rock/debris avalanches. Over 100 residential homes were impacted by landslides, leading to the evacuation of several hundred residents.Volumes of rock leaving several of the larger cliffs during the earthquake sequence were determined from terrestrial laser scan change models. There were no seismically instrumented cliff sites and there was some distance between the cliffs and nearest strong-motion sites. Therefore, we synthesised free-field rock-outcrop seismograms by employing a stochastic approach controlled by source models and regional parameters derived using spectral inversion of the extensive strong motion data set. Relationships between volumes leaving cliffs during the earthquakes and site peak ground acceleration (PGA), peak ground velocity (PGV) and Arias intensity were compared for different sites. Multiple linear regression was used to analyse the variables that best predict the volumes of debris that fell from the slopes during the main earthquakes. The best correlation between the volume of debris falling per square metre of slope face and the seismic forcing parameters was for vertical PGV. The results from the multiple linear regression incorporating slope height, inclination, PGV horizontal and PGV vertical, improved the statistical relationship.Field data and results from the 2D seismic site response assessment indicate that the following factors affect dynamic performance of the modelled cliffs: 1) cliff geology—mainly material modulus, shear strength and shear wave velocity; 2) slope geometry—ridge-scale versus site-scale effects; and 3) the temporal aspects of the earthquake shaking (i.e., single acceleration peaks of large amplitude versus multiple peaks of smaller amplitude). Model results show that amplification of shaking does not increase linearly with increasing height, but instead reflects changes in the cliff geology where material strength, modulus and shear-wave velocity contrasts lead to acceleration contrasts.These factors show that the use of well documented case histories provide the basis for more certainty in seismic landslide assessments compared to those that are only empirically based."

Jan 1, 2015