Search Documents

By Tristan Worsey, John Rathbun, Andres Malone

A run of mine, low grade gold heap leaching operation is currently looking to increase ounce recovery by decreasing run of mine fragmentation size. Current blasting practices have resulted in an average fragmentation size of 80% passing 7.05 inches (179 mm). It is estimated that a decrease of 2 inches (51 mm) in the 80% passing fragmentation size has the potential to yield up to a 2.5% increase in the overall life of mine recovery within this ore body. This potential recovery increase could lead to an increase in recoverable ounces which, in turn, would lead to a better profit margin. As this particular deposit is composed of predominantly low grade heap leach the capital investment in a crushing facility was cost prohibitive, it was therefore decided to look into the current blasting practices as a means to improve fragmentation.

Jan 1, 2015

By H. McIntire, R. Preston, D. Roberts

"Repeated 3D terrestrial digital photogrammetric surveys were conducted on hard rock mine pillars to characterize damage during secondary mining. Damage was quantified by measuring Depth of Failure, DOF, from spalling material and crack intensity, D21. These damage values were then correlated to visually assessed Pillar Damage Ratings and numerically estimated pillar loads. Measured damage, particularly Depth of Failure, correlated well with Pillar Damage Ratings. Numerical predicted pillar stress vs. damage exhibited the expected trend with shorter pillars being stronger. High resolution photographs and 3D models were also used to characterize damage mechanisms, which were found to be structurally constrained. INTRODUCTIONThe Doe Run companies Southeast Missouri Operations consists of six room and pillar lead mines (Brushy Creek, No. 29, Casteel, Buick, Fletcher and, Sweetwater) (The Doe Run Company, 2014). The mines are hosted in the Carbonates and Shales of the Viburnum trend with mining depths varying from 180 to 300 m. Pillars are commonly cut square with widths varying from 7 to 9 m and heights generally between 5 and 18 m, resulting in extraction ratios between 80 and 85% (Roberts et al., 1999). Figure 1 presents an idealized stratigraphic section through the Viburnum trend and Figure 2 shows a plan view of the five areas spanning the three mines included in this study."

Jan 1, 2015

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By Lance Rasband, Richard Hanke

"Seattle Tunnel Partners (STP) started mining on Seattle’s SR99 tunnel on July 30, 2013, working slowly through a 15 ft (4.6 m) thick fiber-reinforced concrete headwall. Once through the headwall, the machine would move through roughly 400 lineal ft (122 m) of jet grout-improved soil at a rate slightly over 6 ft (1.8 m) per day. It was anticipated that once through the improved area, Bertha—the world’s largest tunnel boring machine—would move at a rate of 35 ft (10.7 m) per day. By the end of October 2013, Bertha had mined roughly 430 ft (131 m), averaging 4.73 ft (1.4 m) per day, and had begun mining within native soils. By the start of December 2013, tunneling reached the 800 ft (244 m) mark and Bertha averaged 12 ft (3.7 m) per day, achieving as much as 42 ft (12.8 m) of progress on some days. However, on December 6, 2013, Bertha began to stumble and all progress quickly came to a halt. Preliminary InvestigationInitial reports stated that an obstruction had stopped the machine in its tracks. Malcolm Drilling received an early morning call on Sunday, December 8, 2013, from STP to rapidly mobilize a Bauer BG-50 drill rig with crews to investigate what was hindering Bertha’s progress. Malcolm’s equipment and crews flew into action and were completely mobilized and operational by mid-week. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic head within the ground around the machine and allow STP personnel to inspect the cutter head from within the shaft for presence of obstructions. By the close of December 2013, the wells were installed and the dewatering system was fully commissioned. STP crews were then able to inspect the cutter head and found small fragments of a steel pipe wrapped around the outside of the shield. The steel was apparently from an abandoned 10 in (0.25 m) diameter monitoring well casing previously installed by WSDOT (Washington State Department of Transportation) to monitor groundwater conditions for the design and planning of this very project. After the steel was cut out of the head and cleared from Bertha’s path, she attempted to move forward but was only able to manage a slow crawl"

Jan 1, 2015

By Jack Young

U. S. Steel Canada Inc.’s Lake Erie Works is the last green field integrated plant to be built in North America. The plant was designed using the best available environmental technology to develop an environmentally friendly production facility. A summary of the technology and measures used in the construction of the plant are summarized in this paper.

Jan 1, 2015

By Ørjan Nerland, Torgeir Haugen, Astri Eggen, Kjell Karlsrud

"Ground improvement by the deep dry mixing (DDM) method is used in Norway since the late 1970's. A brief review is given of the Norwegian guideline for ground improvement with DDM issued in 2012, but focus is on practical examples and experiences related to improving the stability of excavations and natural slopes in soft clays. Two examples deal with experiences from 10 to 18 m deep excavations in soft and partly highly sensitive clays, where DDM panels and block stabilization were used to both give sufficient stability against bottom heave and to limit lateral wall displacements. A third case deals with improving the stability of a natural slope in quick clay by installing DDM panels near the crest of the slope. To limit disturbance and excess pore pressures generated during the DDM works, vertical drains were installed in advance in between the DDM panels. This ensured that the excess pore pressures generated by the DDM works (up to 150 kPA) dissipated quickly, which was instrumental to avoid triggering a landslide during the stabilizing works.INTRODUCTIONThe lime column (LC) method developed in Sweden and Japan in the mid 1970's (e.g. Broms and Boman, 1977). Since then, there have been significant developments in Scandinavia and around the world in terms of rigs, mixing machinery and tools, and type of binders used. The method, presently named the ""Dry Deep Mixing"" (DDM) method in contrast to the wet deep mixing methods (WDM) that also have developed significantly over the past decades, e.g. Kitazume and Terashi (2013). The first application of the DDM method in Norway was in the late 1970's to improve the stability of an excavation in quick-clay, then using only lime as binder. Most DDM applications in Norway have also thereafter been to improve the stability of cuts, supported excavations or natural slopes in soft clays. The Norwegian Geotechnical Society (2012) issued in 2012 “Guidelines for design of ground improvement with DDM methods"". The following highlights design issues dealt with. The paper focuses however, on some practical cases where DDM has been used to improve stability of deep excavations and a natural slope in soft and partly highly sensitive clays."

Jan 1, 2015

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By F. Vagnon, A. M. Ferrero, M. Pirulli, A. Segalini

"The topic of this study is the design of flexible fences to mitigate the risk due to debris flow phenomena by means of theoretical and experimental studies analysed in framework of the Rock Engineering System (RES).The study of the interaction between debris flows and flexible barriers is a major challenge since many different aspects concerning both the slope characteristics and the structure features are involved. Debris flows are often triggered by the mobilization of debris deposits that are generated by rock fall of adjacent rock walls. The rock debris deposits are difficult to be characterized by the physical and mechanical point of view due to their large variability in volume distribution and, moreover, when dealing with high mountains environment, they are also strongly affected by the presence of water at different phases (solid or liquid) depending on the temperature. The debris deposit turns unstable in relation with the geotechnical and environmental features of the areas and the instability evolution in high mountain steep valley is often a debris flow. Debris flow destructive potential is very high and protections are often needed to reduce the debris flow risk.This complexity determines the needs of comprehensive study able to include the global basin dynamic and the environmental conditions. An a-priori analysis of the influence of the different aspects can be useful to focus on the real driving aspects of the problem. Due to the complexity of the system the application of the RES methodology is recommended in order to clearly define the different assumptions needed, their influence on the simulations and a comparison among them.RES allows investigating triggering criteria, flow and depositional processes and interaction of flows with protection fences in a rational way. For this purpose, an interaction matrix is created: it summarizes the key geotechnical parameters that influence debris flows, their interactions and debris/engineering protection opera behaviour. The goal is to quantify the diagonal-off terms to assess the residual risk after barrier construction, using back analysis from real debris flow event and data collection from literature.This methodology is applied to analyze a debris flow event in the Italian Western Alps where numerical analyses are carried on to assess flow characteristics to be used for fence design through the application of an analytical and numerical model developed by the authors (Brighenti et al, 2013). In particular, the velocity and deposition heights have been estimated using the numerical code RASH3D (Pirulli, 2010), which is a single-phase model based on depth-averaged Saint Venant equations. Pathways of different lengths are studied to assess the input data necessary to design the protection barrier and to determine the associated risk. Simulation of the barrier at different places along the valley will also allow to determine optimal barrier location in terms of minimum residual risks by comparing the velocity, the volume and the energy of the debris after the barrier impact.The work will produce a possible design scheme to be adopted in this environment."

Jan 1, 2015

By M. Q. W. Jones

This paper presents a compilation of physical properties of rocks from the Bushveld Complex. The database consists of more than 900 measurements each of thermal conductivity and density. The data are well distributed from localities around the Complex and most rock types are well represented. Thermal conductivity and density are shown to vary widely in the ranges 1.8-4.2 W m-1K-1and 2600-4200 kg m-3respectively. Although only 190 heat capacity measurements are available, this parameter is quite uniform for most rock types present, 800-900 J kg-1K-1, except for chromitite, which has a lower average, 750 J kg-1K-1. Rocks encountered in deep platinum mines are particularly well characterized and this has important implications for prediction of mine refrigeration requirements. The heat flux into a semi-infinite region with properties typical of the Bushveld Complex as a function of time is substantially lower than an equivalent model for the Witwatersrand Basin.

Jan 1, 2015

By P. Babak, E. Insalaco, O. Babak, P. Henriquel

"Detection of outliers is an important primary step in geomodelling. Geological datasets often contain errors due to problems such as measurement device limitations and recording glitches. In this paper, a robust Mahalanobis distance–based approach is successfully applied to particle size distributions of the Joslyn lease, an oil sands development site near Fort McMurray, Alberta, Canada. Automatic outlier detection and geological review were combined. Outliers from the Mahalanobis distance approach were compared with their respective core photographs to determine if laboratory measurements and facies classification were correct. A checking procedure for laboratory technicians is proposed.RÉSUMÉ La détection des valeurs aberrantes constitue une étape primaire importante de la modélisation géologique. Les ensembles de données géologiques contiennent souvent des erreurs en raison de problèmes tels que les limitations des instruments de mesure et des pépins d’enregistrement. Dans le présent article, une méthode robuste basée sur la distance de Mahalanobis a été mise en oeuvre avec succès aux granulométries du bail minier Joslyn, un site de sables bitumineux en développement à proximité de Fort McMurray, Alberta, Canada. La détection automatique des valeurs aberrantes a été combinée à une étude géologique. Les valeurs aberrantes de la méthode de la distance de Manalanobis ont été comparées avec leurs photographies respectives de carottes de forage afin de déterminer si les mesures en laboratoire et la classification des faciès étaient correctes. Une procédure de vérification pour les techniciens de laboratoire est proposée."

Jan 1, 2015

By George Filz, Peter R. Cali

"Unnecessarily restrictive specifications could be limiting the cost effectiveness of deep mixing (DM) applications and therefore limiting use of DM on projects where there are other options. Excessively restrictive standards demanded for strength and permeability certainly increase contractors’ bid prices, and costing the owners and, in the case of Government projects, the taxpayers more than necessary. Yet, lax or ineffective specifications often exist for some vital components of the quality assurance and quality control. In this paper, specifications for key elements of DM design and construction are examined. Recommendations are made to improve and streamline DM specifications to better serve the common objective of constructing a safe and cost effective ground improvement project.INTRODUCTIONSpecifications should, at their best, convey the project design requirements and provide clear direction to the contractor regarding requirements for submittals, materials, execution, measurement, schedule, and other aspects as necessary. The specifications should not be overly conservative, restrictive or ambiguous, and they absolutely should not be deficient in measurement of quality. Guide specifications or recycled sections from previous projects often form the template for new project specifications. But standards that appear in guide specifications or from former successful construction should be critically scrutinized by the designer for relevance before using the copy/paste functions of the specifications writer’s keyboard. Because work does not always go as smoothly as planned, specifications for remediation of non-compliant construction should be clearly stated and enforced. Often, non-compliancy is reviewed after-the-fact and deemed to have met the design intent, indicating that either the specifications were too restrictive or the enforcement too weak.The Federal Highway Administration Design Manual: Deep Mixing for Embankment and Foundation Support, October 2013, was written by a panel of DM expert design practitioners and contractors. Guide specifications are included as Appendix C of the FHWA manual. Those guide specifications have been updated in the deep mixing section of the www.GeoTechTools.org website, and the updated specifications represent the most complete and authoritative compilation published to date. Although the specifications for DM at www.GeoTechTools.org are current and complete, and they portray the state-ofthe- practice, they too must be modified to fit specific DM applications, project needs, and site conditions. The keys to a good set of specifications are to prescribe construction only to the level that is required to meet the design intent, to require appropriate quality control and quality assurance (QC/ QA) activities, and to clearly address remedial measures required for non-compliant work."

Jan 1, 2015

By M. Javier

"The impact of mine closure is perceived through a veil of compliance to human laws and regulations rather than the laws and equilibrium of nature. This perception motivates present research. Understanding the causes and effects of mine closure defines levels of responsibility. This understanding evolves from mine closure's legacy. Mine closure is characterized in perpetuity by three aspects: Future liabilities; level of technologies for extraction and, usage of mineral resources. These aspects must be updated to a rationally appropriate level. This paper will address the following questions: Will the minerals remaining in the process of mine closure ever be recovered? Will the mine closure inhibit the availability of minerals for the next generation? How many mines are designed to perform a successful mine closure? Do we close the mines or do we close nature? Is it responsible to continue mine closures as we do them today? Is mine closure a complement of mine operations or a contradiction of mining? Do we need to perform mine closures, yet? This paper reviews mine closure practices and principles with the level of responsibility to nature and for the next generation.PREFACE The planet has irreversible issues to deal with regarding the depletion of mineral resources and contamination occurring from human activities. The population increased exponentially to more than seven billion, this high population with its lifestyles, demands a higher supply of minerals. In spite of these conditions, mining is a vital industry to keep ""civilization"" in society. This is evidenced by what we see around us, in that everything ""made"" in society is directly or indirectly due to mining. Hence, mining cannot be avoided or ignored. Society misunderstands the importance of mining in relation to other activities. At this time, mining is fragmented and economically oriented to supply cheap minerals to a market with peculiar characteristics regarding products that could be designed for recycling and stimulate nature’s equilibrium. These issues add important “variable factors” to the equation, when they are considered as parameters for the next generation. It also raises many questions regarding principles and attitudes about morals and ethics exercised in all anthropogenic activities. The industry's practices have many flourishing paradigms which are subject to a variety of criticisms and observations. Some of these observations will be described in this paper. It is important to clarify in advance a ""normal disclaimer"" about the ""apparent contradiction"" that could take place in the writer's comprehension when we abruptly ""jump to conclusions"". We must remember that we are profiling the future in an arena that demands a better understanding of solutions to problems created by actual mining."

Jan 1, 2015

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By A T. Spathis

The 11th International Symposium on Rock Fragmentation by Blasting (FRAGBLAST 11) was held in Sydney, Australia, between 24-26 August, 2015. The 93 papers, including six keynote presentations, covered exciting and practical topics in 20 sessions within 12 themes. Just fewer than 300 delegates from 27 countries attended. Four workshops were conducted on the weekend prior to the symposium, with three field visits after the symposium to Sydney region quarries, the Hunter Valley coal mining region, and the Kalgoorlie gold mining region. Delegates had the opportunity to visit the exhibition areas that showcased the latest products, software, hardware and systems in blasting technology. The keynote addresses were held in plenary sessions and set the tone for the parallel sessions that followed. They spanned the dynamics of the mining industry, the detonics of explosives, the interaction of stress waves and fracture mechanics in fragmentation, wall control blasting, and the importance of education and engineering for full process optimisation.

Jan 1, 2015

By Alessandro Navarra, Amir Arash Rafiei, Kristian Waters

Mathematical programming (MP) is fundamental to systems engineering and operations management, but has not been widely adopted by mineral processors. The current paper presents an interdisciplinary approach, using MP to incorporate basic notions of mass balancing into an optimization framework. The optimization is typically related to economic profitability. Two- and three-product formulas are extended to give formal descriptions of alternate modes of operation, and a global representation of the concentrator. At this global level, the framework may assist plant managers to make tactical decisions based on incoming feed data. The MP framework is demonstrated through sample calculations describing a lead-zinc concentrator.

Jan 1, 2015

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015