Search Documents

By P Albert, S Crispin, J Hertrijana

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Martabe gold mine is Indonesia’s largest precious metals-only producer and is also one of few significant hard rock mine developments in the past 15 years. Martabe is located on the west coast of the island of Sumatra in the North Sumatra province. The mine commenced operation in mid-2012, producing over 280 koz of gold and 1.5 Moz of silver in its first full year of production.Martabe consists of a cluster of six currently identified high-sulfidation epithermal deposits. The deposits lie in a north–south corridor with an approximately 8 km strike length and 1.5 km width. The total Measured, Indicated and Inferred Mineral Resource Estimate of the deposits is currently 8.2 Moz of gold and over 75 Moz of silver.The exploration program at Martabe has added more than 2 Moz of gold and 15 Moz of silver to the Mineral Resource estimates (Measured, Indicated and Inferred categories) since G-Resources acquired the project in 2009. This has been achieved at an average cost of US$17 in exploration expenditure per ounce of resource added, which includes helicopter-supported drilling programs in rugged forest terrain.The factors that led to this exploration success at Martabe include: in the first instance and most importantly, recognition of the geological potential of the mineralised system continually updating and improving ‘orebody knowledge’ and applying new ideas to the exploration program ongoing engagement and consultation by world professionals with geological expertise in similar systems ongoing executive management support for the program the high quality of work completed by previous owners a strong focus on quality control, staff development and operational safety, with the JORC Code (in particular Table 1 of the Code) as the underlying basis for quality control continual and positive engagement with government, community and other external stakeholders.This paper will discuss in detail the first of these two factors. It is important for the modern exploration team to recognise that mineral potential on its own is not sufficient for exploration success, so this paper will touch on the other factors as secondary but crucial considerations.CITATION:Crispin, S, Hertrijana, J and Albert, P, 2015. Exploration success at the Martabe gold mine, Indonesia, in Proceedings PACRIM 2015 Congress, pp 567–572 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P. Beauvais

Philip Beauvais, from the Met Office's International Mining and Agriculture Department, explains the need to understand the impact of the weather and climate when developing future mine sites.

Mar 1, 2015

By Schwartz M.

Respect for mining in Botswana is long-standing. This article looks at Africa's most transparent mining regime and some of its ambitious plans. Botswana's mining industry value is forecast to average 5.2% growth from 2014-2018 with solid growth for the diamond sector and acceleration of coal production. Respect for the country's mining regime is maintained in the Fraser Institute 2014 annual survey where Botswana occupies the 26th position of 122 administrations. Botswana's transparency is illustrated by Mupane gold mine near Francistown, Ghaghoo diamond mine in the Gope area and the Morupule coal mine

Mar 1, 2015

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs. Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By Ron Zevenhoven

In Finland one opportunity for large-scale CO2 capture, utilisation and storage (CCUS) is CO2 mineralisation, i.e. mineral carbonation. A process route under development towards industrial application involves production of magnesium hydroxide or sulphate from serpentinite rock (serpentine = 3MgO·2SiO2·2H2O), followed by conversion either in a pressurised fluidised bed (PFB) reactor, giving magnesium carbonate, or in an aqueous solution process giving magnesium hydro-magnesites. Iron present in the rock is typically obtained FeO(OH). Results obtained with these process routes and progress towards industrial demonstration is addressed, process heat integration and operation on flue gases (without CO2 pre-separation!) being key features for economic viability. A process route utilizing calcium-containing slag by-product from iron- and steelmaking under development towards large-scale application is the so-called slag2pcc concept. It converts an industrial by-product into valuable material, reduces use of natural material and streams to landfills while binding CO2 produced by the process generating the slag. Using ammonium salts, calcium is extracted from steel converter (BOF) slags and subsequently carbonated in a two-stage aqueous process (at ambient temperatures and pressures). Precipitated calcium carbonate (PCC) is produced while regenerating the ammonium salt. Process performance and scale-up while guaranteeing a certain PCC quality are presented.

Jan 1, 2015

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By A. M. S. Hussein, B. E. Rogers

Progressively more stringent emission limits and advances in regulations and enforcement have made air compliance more difficult for metallurgical facilities. This has historically required improved collection and treatment of stack sources. Fugitive emission reductions are now increasingly required to achieve compliance. Typically small in magnitude, fugitive emissions have a disproportionate impact on ground level concentrations, can be visible to the public and can influence workplace health and safety. Moreover, these emissions are complex, as they are spread over multiple sources, distance and time and are affected by various activities and conditions. As such it is difficult to find, define and monitor these emissions and their impacts. This difficulty translates to the design of emission reduction measures and operational requirements. This paper presents an overview or ‘heuristic’ of fugitive emissions management for compliance in existing operations. This includes aspects such as the impact of regulations on project scope, approaches to developing a comprehensive emission inventory, considerations for solution development and the plant’s role in sustaining compliance once achieved. Case studies are presented to demonstrate how portions of this approach have been applied.

Jan 1, 2015

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By A. Noble

"Linear circuit analysis (LCA) is a fundamental tool that may be used to evaluate, design and improve the performance of mineral separation. The traditional LCA methodology provides a comparative evaluation of circuit designs purely from the unit interconnections. The quantitative approach uses the analytical circuit solution to evaluate the slope of the circuit’s partition curve at the midpoint. Since the partition slope is often associated with a separation’s general selectivity, this numeric value is used to compare and rank alternative configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. By itself, this value does not account for the relatively high unit dollar value of pure material or the gains and losses in mass yield associated with alternative circuit configurations. Realizing the value in the LCA methodology, but respecting the limitations of the partition slope valuation, the authors have derived two new performance indicators that quantitatively address pure particle misplacement (the Partition Moment of Inertia) and circuit mass yield (the Yield Score). Together, these parameters provide a better indication of separation economics in typical mineral and coal separation systems. Since the two parameters provide independent information on circuit selectivity and circuit yield, a Pareto efficiency, multi-objective function selection approach is proposed for preliminary circuit selection.IntroductionOver the past 30 years, numerous scientific and industrial studies have proposed various mineral processing circuit design methodologies that attempt to optimize the allocation of separation resources within the processing plant. Over this period, the methodologies have undergone various transitions, including the increased inclusion of process models and computationally intensive algorithms, as well as a general shift from a purely technical solution (Lauder and McKee, 1986) to partially economic solutions (Abu-Ali and Sabour, 2003; Cisternas et al., 2014). Today, circuit design is largely driven by flowsheet simulation; however, no consistent design methodology is used across the industry.One intriguing approach for circuit evaluation is linear circuit analysis (Meloy, 1983a). This method evaluates the separation potential of the circuit solely considering the unit configuration and stream interconnections. No preliminary data other than the basic circuit configuration is required to use the approach."

Jan 1, 2015

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"The Copper Mountain Mine is located in Princeton British Columbia, Canada and produces 80 – 90 million pounds of copper annually, as well as gold and silver by-products. The ore processing plant has a conventional SAG/ball mill circuit with inline pebble crushing, followed by flotation. At most plants, much time is spent evaluating and optimizing the comminution and flotation circuits. The cyclones are a key contributor to the effective operation of the plant: They define the circulating load in the comminution circuit and provide the classification that ensures liberated material is passed through to flotation. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput in flotation. For such an impactful unit operation, cyclones have historically been under-instrumented. Consider as well that the cyclones are typically located at the highest elevation in a plant, and it becomes clear why they often underperform. Copper Mountain Mine recognized the critical role that cyclones filled in their plant and worked to optimize their operation through the implementation of a Portage Cyclone Detection (PCD) system to identify plugging and roping incidents, Portage Pumpbox Control (PPC) to manage the flow to the cyclones, and AwaRE to control the grinding circuit. As a result, cyclones overflow stability has increased, switching out a roped or plugged cyclone now happens within seconds rather than many minutes, and both the grinding and flotation circuits perform better. INTRODUCTION Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. The cyclones are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations. The cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance to have proper stability in cyclone operation while implementing any plant-wide optimisation strategy."

Jan 1, 2015

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into usable form and, as such, present a real processing challenge in that the deposits are never homogeneous and orebody compositional characteristics are all over the map. Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning, and accounting systems. Key to the automation process is the aspect of value generation. This article brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.Minerals’ processing sites are historically long lived, with 20-year life-of-mine not uncommon and 75 years not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must, therefore, be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an extractive industry that is physically oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce variable outputs. But times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and nonlinear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contributions are necessary to mining operations for value generation."

Jan 1, 2015

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

By Christopher Mark

"Many problems in rock mechanics are limited by our imperfect knowledge of the material properties and failure mechanics of rock masses. Mining problems are somewhat unique, however, in that plenty of real world experience is generally available and can be turned into valuable experimental data. Every pillar that is developed, or stope that is mined, represents a full-scale test of a rock mechanics design. By harvesting these data, and then using the appropriate statistical techniques to interpret them, mining engineers have developed powerful design techniques that are widely used around the world. Successful empirical methods are readily accepted because they are simple, transparent, practical, and firmly tethered to reality.The author has been intimately associated with empirical design for his entire career. But where his past papers have described the application of individual techniques to specific problems, the focus of this paper is the process used to develop a successful empirical method. A six-stage process is described:1. Identification of the problem, and of the end users of the final product2. Development of a conceptual rock mechanics model, and identification of the key parameters in that model3. Identification of measures for each of the key parameters, and the development of new measures (such as rating scales) where necessary4. Data sources and data collection5. Statistical analysis6. Packaging of the final productEach of these stages has its own potential rewards and pitfalls, which will be illustrated by incidents from the author’s own experience. The ultimate goal of this paper is to provide a new and deeper appreciation for empirical techniques, as well as some guidelines and opportunities for future developers."

Jan 1, 2015

By P. Karimi, A. Akcil, A. Amini, H. Abdollahi

"In this study, cyanidation experiments were carried out on a massive sulfide ore sample, whose grades of the precious metals gold and silver were found to be 4.2 g/t and 311.9 g/t, respectively. Other elements in the ore were arsenic with average grade of 1,751.6 g/t; antimony, 619.7 g/t; zinc, 781.4 g/t; copper, 454.6 g/t; lead, 101.8 g/t; mercury, 324.3 g/t; and bismuth, 0.6 g/t. The first objective of test work focused on determining the best conditions for extracting gold from the ore, ground to less than 75 microns. Different influential parameters such as particle size fraction, cyanide concentration, pH and leaching time were investigated. The optimum parameters were found to be particle size fraction of less than 25 microns, cyanide concentration of 2,000 mg/L, pH of 11 and cyanidation time of 24 hours. In these optimum conditions, the highest gold and silver leaching efficiencies were 76.88 and 59.63 percent, respectively. In addition, roasting as pretreatment at a temperature of 700°C over a period of two hours was evaluated. Cyanidation testing of the roasted ore in the optimum conditions found increases in the gold and silver leaching efficiencies to 85.97 and 67.57 percent, respectively. Moreover, antimony extraction rose to 43.10 percent, from 23.73 percent without roasting.IntroductionGenerally, gold ores can be classified as “free milling” or “refractory,” depending on how they respond to cyanide leaching (La Brooy et al., 1994; Celep et al., 2009). While high gold recoveries (> 90 percent) from free-milling gold ores can be readily achieved, refractory gold ores are often characterized by low gold recoveries (50-80 percent) within a conventional cyanide leaching process (Rubisov et al., 1996; Adams, 2005; Celep et al., 2009). The presence of preg-robber components such as carbonaceous matter, sulfide minerals and aluminosilicate can further decrease gold and silver dissolution rates and recoveries. With the negative effect of the presence of preg-robbers, gold dissolution is considerably diminished in solutions with high cyanide concentration (Tan et al., 2005). In such refractory gold ores, gold particles may sometimes be occluded or included in the sulfide minerals, and pretreatment becomes necessary to break down the mineral structure to liberate gold for subsequent recovery. These ores are usually pretreated with an oxidizing process, after which gold and silver can be recovered by a standard cyanidation process. The main oxidizing processes available for refractory gold ores are roasting (LaBrooy et al., 1994; Angelidis and Kydros, 1995; Li et al., 2009; Karimi et al., 2010; Kyle et al., 2012), biological oxidation (Lawrence and Bruynesteyn, 1983; Komnitsas and Pooley, 1990, 1991; Deng and Liao, 2002; Ciftci and Akcil, 2010, 2013) and pressure oxidation (Mason, 1990; Murthy et al., 1992; Qingcui et al., 2009). In addition, ultra-fine grinding is being used in some plants for the liberation of gold and silver particles that are interlocked in the sulfide or silicate minerals (Celep et al., 2011)"

Jan 1, 2015

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By Leena Korkiala-Tanttu, Ilkka Vähäaho, Juha Forsman, Paavo Lahdenperä, Kalle Rantala, Osmo Korhonen

"District of Arabianranta (Helsinki, Finland) has been founded on an old seabed, which was filled with miscellaneous soil materials. The subsoil consists of very low shear strength clays and organic clays (gyttjas). The soil was moving towards the sea at a rate of 1050 mm/year, because of filling on top of the soft subsoil. In the middle of 1990’s it was decided to build a residential area to Arabianranta, because it is located only 5 km away from the downtown. To inhibit the movement of soil, it was planned to build this 700 m long deep mixed column-wall barrier along the shore of Arabianranta in the years 1997–2005. A lot of instrumentation and inclinometers were analyzed and it was noticed that the column-wall remains at its place and the displacement rate inside the wall has been only 0.44.6 mm/year after construction works. Nevertheless, the displacement of soil at the landward side of the column-wall is still 1.25.1 mm/year. The soil at the seaside of the barrier is also moving towards the sea 12.922.2 mm/year. Another problem might be displacements of soil near the places where the column-wall ends (tails).1. INTRODUCTIONArabianranta district (Helsinki, Finland) has been an industrial, storage and wasteland area for a long time. Developing this area into a residential area was earlier considered too expensive, so it has been constructed during last decade. The organic clay layers (gyttjas), which have weak shear strength and high water content, were covered by various layers of fillings done in different phases. Because of the fillings, the area was not only consolidating, but also moving horizontally 1050 mm/year towards the sea due to the fact that the frictional soil under clay layers slopes towards the sea. A trial deep mixed structure was constructed in 1997 to inhibit the horizontal displacements of soil. The actual construction of the columnwall was completed in 2000-2005 with overlapping deep mixed cement columns on the seaward boundary. The barrier was built so that the horizontal movements would not risk the pile foundations at Arabianranta. The length of the barrier is about 680 m and width varies between 1220 m. There is a great amount of instrumentation near the barrier (inclinometer casings and other measuring devices). All this measuring information has been collected and analysed at 2014 to find out how this deep mixed column-wall has affected the horizontal displacements."

Jan 1, 2015