Search Documents

By Peter Johnson, David Barber, Lachlan Henderson

"Within underground portions of metro rail networks the traditional approach to a design fire has been to assume a worst credible railcar fire and develop ventilation and egress measures for life safety. This approach is being challenged as a rail network approach to design fires becomes a more practical and realistic approach. The network approach is based on utilizing an in-depth hazard analysis, to understand ignition and fire load sources in tunnels, above and below the floor of the railcar and within stations, and then utilizing a quantitative risk assessment to determine sets of fire scenarios. The process allows small, medium and large fires to be considered, with the consequences also being quantified. The selection of design fires has a significant influence on fire protection measures within a metro network and hence, is a major cost input. The rail network approach provides more robust decisions on fires, based on the hazards present. INTRODUCTION A fire within a rail car or one that occurs as part of a rail system can threaten the lives of users, maintenance staff and emergency services personnel. Fires in metro systems are rare events but can have severe consequences. As a result, any analysis of a potential fire must be thorough and rigorous and address not only regular accidents and small fires, but also very low probability, high consequence scenarios. The fire safety design process for a tunnel and station must start with the design engineers, contractor and operators making a number of key decisions related to fire protection measures, which may have significant cost considerations. One of the key aspects that influences the required fire protection is the design fire and the design fire scenarios, which is a key input for analysis. This paper provides an overview of the author’s experience in designing fire protection measures for rail networks in Europe, Australia and NZ, where a risk based framework is used to develop design fires and scenarios for the whole rail system – trains, stations and tunnels. This system wide approach is innovative, challenges the norms, but provides significantly more informed outcomes. The range of design fires will include small fires that may halt the network, larger fires for smoke hazard system design and significant post-flashover fires to assess the structural response."

Jan 1, 2016

By S. F. Burks

"This paper develops themes explained at two SAIMM platinum conferences. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can be increased significantly, usually even before the expenditure of significant amounts of project capital. Recent studies of NPV have aimed to simultaneously evaluate the impact of the optimized financial solution on the non-financial features of a project or operation.The case study presented comprised a commercially orientated review of the prefeasibility study designs and cost estimates of a platinum group metal (PGM) project in South Africa, followed by value chain optimization and sustainability studies of the project carried out simultaneously to identify potential value uplifts to be gained and guide the owners’ team going forward into the feasibility study phase. Some of the major aspects of the project that were found to have significant potential to add value included enhancement of the business model by the application of activitybased costing and theory of constraints, focus on the highest net value portions of the orebody in the early years of production, enhanced and optimized scheduling of the underground mining operation, application of dynamic grind and percentage mass recovery from ore to flotation concentrate (also known as percentage mass pull) to optimize revenue, application of elevated cut-off grades early in the life of mine, matching of the mining and processing capacity, expansion of the operation subject to capital availability, and installation of downstream processing facilities subject to regional third-party capacities.The investigation of non-financial project features focused on demonstrating that a financially optimized solution could also have a number of other benefits. These are mentioned briefly in the paper, which aims to present the status of the project at an early stage of its development."

Jan 1, 2016

By Andy Thompson, Frank Perrone

"As part of the Metropolitan Transportation Authority’s $10.5bn East Side Access Project in New York, 3,200 m of tunnel had to be constructed in rock, mix face and soft ground conditions beneath one of the largest passenger railroad junctions in North America, handling over 780 trains per day. The use of risk based decision making tools was essential in developing the bespoke contract framework that was adopted as well as making informed decisions once excavation commenced. This paper will outline the risk management process adopted, discuss the risks and mitigation strategies adopted and comment on the impacts of this approach on the as built Project cost and schedule. In particular, the paper will outline the unique approach used to establish the baseline against which the Contractors performance would be measured as the selection of a Slurry TBM to excavate the tunnels was considered to compromise the effective use of a Geotechnical Baseline Report. BACKGROUND AND CHALLENGES Contract CQ031, Queens bored Tunnels and Structures was awarded in September 2009 to a joint venture of Granite Northeast/Traylor Brothers/Frontier Kemper (GTF JV) for $717.6m following a negotiated procurement process. A robust approach was taken with regard to the management and payment for risks associated with the construction of these tunnels. Risk assessments were carried out during the design phase and a risk register was developed prior to procurement. During the procurement phase close attention was paid to ensuring that the allocation and pricing of known risks, together with mechanisms for managing future risks were clearly defined between the MTA and GTF JV.In comparison to the excavation work in Manhattan, which was performed in competent hard Manhattan schist, the tunnels in Queens were excavated predominantly through soft ground with a high water table and complex environmental conditions. Not only did this require the use of pressurized face TBM technology, a first in New York, but also a re-evaluation of the contractual mechanisms used to manage the hard rock excavation contracts for their appropriateness to the soft ground tunnel work."

Jan 1, 2016

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By Imane Benhamed, Jaouher Diouani, Laurent Cassayre, Florent Bourgeois, Carine Julcour-Lebigue, Université de Carthage

The attrition-leaching process aims at improving leaching performance when formation of passivation layers at the surface of leached particles is a severe limiting factor, as discussed recently by Julcour and coworkers (Julcour et al., 2015). This paper proposes a geochemistry-based modelling scheme for deriving the window of possible operating conditions for the attrition-leaching process to match the properties of the processed ore. The rationale is that the attrition-leaching process maintains the surface of reacting particles in an unpassivated state by continuous mechanical removal of surface leach layers, so that the process reactions can be modelled from thermodynamic equilibria throughout the duration of the process. The strength of the proposed modelling approach is that it bridges the gap between the properties of the ore and the process operating conditions. The present paper exemplifies the proposed process modelling route for derivation of the attrition-leaching process operating conditions in the context of the leaching of silicate ores, matching model predictions against controlled laboratory experiments. It is shown how thermodynamic modelling, when used in conjunction with a solid knowledge of the phases present in the system, can assist with deciding upon suitable process operating conditions. As an example, this firstprinciple modelling approach predicted that steel grinding medium would be converted into siderite (FeCO3) under a wide range of operating conditions, which led to questioning this initial choice of grinding medium for the attrition-leaching process under mineral carbonation conditions. It is emphasised that the same approach could be applied to ores of greater economic significance.

Jan 1, 2016

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

By Johannes Jäger

"A composite shell lining typically consists of an outer permanent sprayed concrete shell, a water proofing layer and an inner sprayed or cast concrete shell. Composite shell linings become more and more popular and have been built recently on large scale infrastructure projects. Surprisingly there is very little published literature on the actual structural design of composite linings. As a consequence there is a lack of common understanding on how to design a composite lining structure. Composite action of the outer shell (primary lining) initially carrying short term ground loads and the “unloaded” inner shell (secondary lining) require nonlinear concrete modelling to be able to assess the bearing capacity of the composite lining structure adequately. The composite action of the waterproofing membrane and the inner and outer shells can be considered either by simplified closed form solutions or by numerical models. Strength and stiffness parameters of membrane and concrete govern interaction of inner and outer shell. This paper should contribute to understanding composite lining behaviour with focus on the bearing capacity at limit state by taking into account the actual loading history. Possible ways and concepts on how to deal with these topics are presented, however a broader discussion on limit states of the composite lining materials – also in the long term will be required to come to an agreement on composite lining design methodology. INTRODUCTION Composite Lining Technology Traditionally the construction of shotcrete lined tunnels incorporates primary and secondary linings, separated by a sheet or a sprayable waterproofing membrane. The primary lining shotcrete is considered to be structurally temporary and the secondary lining to be permanent, leading to designs which ignore the bearing capacity of the primary lining in permanent condition. There was general perception that the shotcrete lining installed immediately at the tunnel face, experiencing strains up to 1% and even cracking in the early age, combined with mesh reinforcement additional support measures like lattice girder, spiles and bolts cannot be considered as a permanent structure. But also former shotcrete mixes showed significant weakness with respect to durability suggesting a more temporary nature of primary lining shotcrete. On the other hand it was clear that primary lining shotcrete does not disappear, it may lose probably a certain percentage of its bearing capacity, but discounting any contribution from the primary lining at all was considered inherently conservative. There were different strategies to account for the risk of reduced durability and bearing capacity of the primary lining, either by selecting moderate ground loads for the secondary lining design, by assuming that some residual load will be carried by the primary lining. This approach is very much based on experience. Another more rational possibility is to assume that the primary lining degrades into a rocklike material, which is weaker than the primary lining shotcrete but still imparts some strength to the ground around the secondary lining, but does not need to comply with any concrete design codes any more."

Jan 1, 2016

By Sotiris Psomas, Colin M. Eddie

"Steel Fibre Reinforced Concrete (SFRC) Segmental Tunnel Linings have successfully been used for over 20 years in the UK and have been adopted in a number of high profile projects such as High Speed 1, Crossrail, Thames Tideway, as well as High Speed 2. Tunnel linings and especially SFRC design are not covered in the Eurocodes. This shortage of SFRC tunnel design rules seems to be partially addressed by several international publications. However, in the UK, the ‘design-assisted by testing’ (DAT) approach has also been adopted. The Paper discusses the UK’s best design practice and focuses on the DAT methodology as applied in the case of the 6.9km (4.3miles), 7.8m (25.6 feet) ID Lining for the £635million Lee Tunnel Project. The design approach, the full scale testing at the Building Research Establishment (BRE), and the construction innovations are presented. This experience will be transferred to the £4billion Thames Tideway Tunnel.INTRODUCTIONSteel Fibre Reinforced Concrete (SFRC) has been used for Tunnel segments for more than 20 years. The first application of SFRC in the UK was for the Heathrow Baggage tunnel (1994). Since then significant size tunnels have been designed and constructed, such as the Jubilee Line (1999) High Speed 1 (CTRL, 2006), Crossrail (2014), Lee Tunnel (2014) and the scheduled 25km Thames Tideway (‘Super Sewer’) and High Speed 2 rail tunnels. However one the main obstacles in achieving streamlined design and improving efficiency are the lack of appropriate design guidelines for SFRC tunnel segments. This issue will – to some extent – be addressed by a number of current documents on tunnel FRC design either being produced by BSi (PAS8810, expected 2016), ACI (544.R) and ITAtech (Design Guideline PCFRC, 2015) in an effort to advance the design of SFRC and take into consideration the recent developments in Steel and Macro-Synthetic FRC technology."

Jan 1, 2016

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By Eleanor Kentish, Edward Batty, Alan Skarda

"The design of the tunnels at Bond Street Station includes a final sprayed concrete fireproofing layer. The performance of this layer was verified by a program of testing to Crossrail’s KT24 specification, which proved that a dosage of 1kg/m³ polypropylene fibers and a layer thickness of 50mm would be sufficient to limit spalling in the event of a fire. Application of this thin layer was achieved using a state of the art spraying robot, with the ability to scan the profile and automatically apply a uniform layer of concrete. To provide assurance and calibrate this spraying robot, BFK developed a bespoke survey system for checking SCL thicknesses in the field. This provided an instant independent check of the spraying robot and allowed areas of inadequate thickness to be rectified without risk of cold joints. This paper describes the practical application of the fireproofing layer and how design compliance was ensured. INTRODUCTION Fire is one of the most serious risks to a tunnel. The nature of tunnels — being long enclosed spaces — can increase the intensity of a fire, and make fire-fighting and rescue operations difficult. The damage that can be caused has been demonstrated by a number of historic tunnel fires, such as the Channel Tunnel fires of 1996 and 2008, and the Mont Blanc Tunnel fire in 1999. Without any intervention, the high temperatures in a fire create thermal stresses and a build-up of vapor pressure within the pores of concrete, which eventually exceed the tensile strength and trigger explosive spalling. Spalling exposes the core of the section to severe temperatures, leading to a loss of concrete and steel reinforcement strength or further spalling of successive layers. The concrete used in tunnel linings is particularly susceptible to explosive spalling, due to its low permeability achieved by the addition of microsilica (Bailey 2011). The sprayed concrete lined (SCL) tunnels on Crossrail have been designed to resist the worst anticipated fire in operation, in order to prevent collapse and minimize damage to the structure. The design called for a system of passive fire protection, the efficacy of which was validated by the contractor through a testing regime. It was critical that the application on site reflected the test conditions, which demanded special control of the profile and thickness of the lining. In order to meet these constraints on tolerances and quality, BAM Ferrovial Kier joint venture (BFK) developed a reliable method of working with the Meyco Logica spraying robot, and a bespoke survey system for accurately checking thicknesses in the field. These innovations are the focus of this paper."

Jan 1, 2016

By Tom Barry, Kameron Ray, Dr. Gavin Yuill

Imerys Talc, Yellowstone Mine in Montana faces significant geotechnical challenges such as poor wall quality and local instabilities. These instabilities are driven primarily by the characteristics of the rock mass, but are aggravated by drilling and blasting operations.

Jan 1, 2016

By Pedone Ezio Michele, Mohamed Dahir Holad

"The 4c segment is a part of the ""Oman National Railway Project” linking the mining area in the surroundings of Thumrait and the port of Salalah. It is 90 km long and the last 40 km stretch crosses a mountainous area near the city of Salalah. The project includes the excavation of a 33 km double and single bore tunnel and 10 km of safety tunnels. This mountainous area is a holiday destination for Omanis, thanks to its beautiful landscapes, especially in summer time due to the monsoon rains. The tunnelling design had to take into account both these environmental constraints and the limestone rock formations crossed, which are affected by significant karst features. Given the context, the conventional tunnelling method has been preferred. INTRODUCTION The Oman Railway Project (Fig. 1) covers the construction of approximately 2,150 km of railway line for freight and passenger transport which will connect together Oman’s main towns and industrial sites and it will form part of the Arabian Peninsula railway system “GCC Project”. The non-electrified double-track railway line must guarantee a speed of 220 km/h for passenger trains and 120 km/h for freight trains and must guarantee the transit of AAR (Association of American Railroad) H and D plates using clearance envelope according to AREMA (American Railway Engineering and Maintenance-of-Way Association) requirements. The design alignment must have maximum radiuses of curvature of 3,250m and a maximum gradient of 1.0%. The project is divided into 9 constructional and functional segments. •,Segment 4c will be constructed in the southern region of Oman, close to the border with Yemen, to connect the town of Thumrait with the Port of Salalah. •,Segment 4c will run through the Dhofar region and will be mainly used by the freight traffic which currently travels by road."

Jan 1, 2016

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016