Search Documents

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By R. J. Mitchell

Results from investigations into impurity distributions over cathodes are presented with implications for various sampling methods, Selection of an optimum treatment procedure for the test sample is outlined. The impact of both these studies on the development of an in-house method for sampling Isa Process cathode is discussed. The economic compromise actually undertaken, satifying wants and needs to sustain confidence in high grade cathode purity is detailed.

Jan 1, 1987

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By Benjamin P. Hay

Complexation of a metal ion to a ligand often results in structural changes that introduce steric strain within the ligand. A design criterior:1 for ligands that will complex metal ions more strongly is to choose Iigar:1d architecture, that minimizes this strain. This paper describes how molecular mechanics models can be used to define the degree of ligand binding site organization in terms of' ,strain energies associated with conformational reorganization and distortion of the binding conformer. This approach yields a method to predict how modifications to ligand structure will affect metal binding affinity.

Jan 1, 1999

By D. A. Robbins

The Resource Conservation and Recovery Act. of 1976 (RCRA) requires testing of waste materials as part of the determination of whether these materials are classified and managed as hazardous wastes. The adoption of one standard testing procedure and its application to all types of waste materials has stirred much controversy. In the center of this controversy is the appropriateness of this testing procedure in characterizing non-ferrous metal intermediates and slags. The authors have evaluated the relative availability of metals in several types of copper and lead slags as defined by various testing protocols. Also discussed is the relationship between the chemical character of the slag and the availability of metals to leaching and certain metallurgical practices that can influence metals availability.

Jan 1, 1983

By Bob Hannah, Peter C. Hayes

The changes that are happening in the world of metallurgy, and with it university education, are generational and require generational responses. Some of the key issues facing metallurgical education and ongoing professional training are explored. What will be required of metallurgical engineering professionals in the coming decades? What knowledge and skills will be needed? How to provide the educational and learning pathways, and how to attract smart young people into this profession? These are issues more readily addressed by tertiary institutions in conjunction with industry; perhaps the greater challenges lie in building and maintaining competencies post-graduation. There is a need to establish and maintain a system that supports graduates and enables them to develop further into competent expert engineers able to successfully address complex engineering challenges.

Jan 1, 2014

By Don Ibana

Supported by the Minerals Council of Australia (MCA) through the Minerals Tertiary Education Council (MTEC), three Australian universities–Curtin University, Murdoch University and the University of Queensland–have formed the Metallurgical Education Partnership (MEP) to jointly develop and deliver an engineering design capstone unit–Metallurgical Process and Plant Design–in their respective undergraduate programs in extractive metallurgy, in order to enhance the students’ educational experience. A unique feature of the program is the close interaction of the students in all three universities and a significant involvement of industry professionals. Now in its sixth year, it is clear that this unit is achieving its objectives

Jan 1, 2014

By Chunhua Liao, Chao Peng, Guangsheng Huo

To get the separation of tungsten and molybdenum, we adjusted the pH of the solution to 7, at which tungstate (WO4 2-) will be polymerized into HW6O21 5-, while molybdate will still exist in the form of MoO4 2-. Two strongly basic anion exchange resins (D201, D213) were experimented for the separation of tungsten and molybdenum. The results of condition experiments indicate that D213 resin performs better in the treatment of lower concentration solution A (WO3 10g/L, Mo 4.12g/L) with a separation factor as high as 10.64. While D201 resin is more suitable for the high concentration solution B (WO3 70g/L, Mo 28.97g/L) with a separation factor of 6.9. The results of column testing performed on D213 resin show that the solution after loading process with a mass ratio of Mo/WO3 = 50 and the desorption solution with a mass ratio of WO3/Mo = 27 can be obtained

Jan 1, 2014

By André L. B. Bittencourt

The copper content in the waste slag represents the greatest loss in the process of Caraíba Metais' Smelter. By identifying the variables responsible for copper stabilization in the slag, a minimization on these losses is expected, producing a granulated waste slag with a copper content lower than 0.7%. Statistics resourses such as control charts, Pareto's diagram and correlations curves were applied for the data obtained in the first semester of 1992. The magnetite and the calcium oxide contents in the slag of the Flash Smelter Furnace were most prominent variables. Some operational changes introduced during and after this investigation have shown good results.

Jan 1, 1994

By C. S. Simons

This paper presents a review of the extractive processes used in the production of nickel, with emphasis on developments since the beginning of the Second World War. Attention is given to the factors, many outside the nickel industry itself, which determined the direction of process research and strongly influenced the ultimate commitments to industrialize the resulting developments. An example of such a factor is the sudden surge in demand, far exceeding the then available nickel production capacity, that was caused by the advent of World War II; the result was the first serious consideration ever given to low- grade laterites as a viable source of primary nickel. Other factors discussed include such items as process development in the extraction of other metals - particularly copper; the availability of increasingly sophisticated materials of const- ruction; the advent of the "environmentalist" and related political developments; the massive escalation in the price of energy - particularly oil. The paper concludes with an attempt to forecast the nature of the most effective nickel process of the future, based on extrapolation from the economic and political situation that exists today.

Jan 1, 1988

By J. E. Klein

Bench scale tests using a stack of ten whole SAES St909 pellets, 6 grams, to crack methane have been completed with pure methane feed. Test conditions ranged from 600 to 800°C at 101 kPa (760 ton) with a methane feed rate of ten sccm. Methane reformation tests, test where hydrogen was passed through a St909 bed after cracking methane, were performed to determine if and how much methane can be generated under "reformation" conditions. Phase structure determinations of St909, composed of a ZrMnFe alloy with aluminum used as a pellet binder, after methane cracking were complicated by the number of materials that can be formed by the elements in the St909 and the carbon from methane cracking. It was determined that the aluminum not only alloys with the Zr, Mn, and Fe in the St909 alloy, but also forms aluminum transition metal carbides in addition to ZrC as the carbon content and the temperature of the St909 increases. Some A14C3 was also found in some pellets. Passing hydrogen over St909 pellets after methane cracking formed methane at various rates in the temperature range of 600 to 800°C. Temperatures of 800°C gave the best methane cracking performance and efficiencies decreased rapidly with temperature.

Jan 1, 2002

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By Herman Wotruba

Mercury emissions and other environmental impacts in small-scale gold mining are a world-wide problem. "Clean" or better: "Cleaner" technologies have -apart from being environmentally sound -to guarantee a higher income and better working conditions for the miners in order to have a chance for long-term acceptance. In small scale primary gold mining in several South American countries, a number of techniques have been adapted and improved so that they not only were accepted due to their efficiency and easy handling, but they could also significantly lower mercury emissions.

Jan 1, 2003

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By Jim A. King

The total pressure oxidation of copper concentrates is a potentially viable option for treating copper concentrates that are either low grade or contain significant impurities. Both concentrate types are heavily penalized in smelter contracts. The total pressure oxidation process involves autoclaving the copper concentrate at temperatures of 200-220 C under oxygen pressure. The autoclave discharge can be separated into a solid (oxidation residue) and a liquid (oxidation solution) product. The oxidation solution can be treated for copper recovery by solvent extraction - electrowinning or by direct electrowinning. The direct electrowinning recovery of copper requires prior removal of selenium and tellurium by cementation on finely divided scrap copper. The oxidation residue is washed thoroughly to remove acid and dissolved copper prior to precious metals recovery by conventional cyanidation in the presence of lime. The results of a benchscale investigation involving a number of copper concentrates are reported. Copper recoveries in autoclave oxidation and gold recoveries by cyanidation of the oxidation residue exceeded 99%. The results of benchscale experiments to demonstrate copper recovery are described. Various flowsheet options are presented.

Jan 1, 1993

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003

By T. S. Piwonka

Modeling the solidification of shaped castings has progressed beyond the initial problem of determining the correct heat and fluid flow relationships which describe the solidifying castings. Today the challenge is to describe second order effects which determine the ultimate quality of the casting. The challenges to the modeling community posed by the needs of today's foundries for models that work are discussed, with some examples of current modeling problems.

Jan 1, 1992

By N. Tsuchida

Sumitomo Metal Mining Co. Ltd. (SMMC) is currently developing the flowsheet to treat stockpiled limonite, a type of laterite ore, at Rio Tuba on southern Palawan Island, Philippines. The new plant will be commissioned at the end of 2004. Rio Tuba Nickel Mining Corporation (RTNMC) has been mining saprolite since 1977, and the limonite ore located above the saprolite ore body has been stockpiled separately according to nickel and magnesium content. Ore from these stockpiles will be blended and used for the operation. The annual production of nickel will be 10,000 metric tons for the next twenty years. The proposed process consists of ore preparation, high pressure acid leach (HPAL), counter- current decantation wash, impurity removal and sulfide precipitation. Precipitated mixed sulfide will be processed to electrolytic nickel by the Matte Chlorine Leach Electrowinning (MCLE) process at Niihama, Japan. SMMC has established new technologies during the process development, such as zinc removal and sulfide precipitation. Applying this technology, preferential removal of zinc can be achieved by hydrogen sulfide gas with negligible loss of nickel. Precipitation of nickel by hydrogen sulfide gas is carried out at low temperature. Slow kinetics is selected for control of the particle size of the precipitated mixed sulfide. Keywords: HPAL, Zinc Removal, MS Production

Jan 1, 2004

By John J. Jonas, Sang-Hyun Cho, Ki-Bong Kang

"The recrystallization behavior of Nb micro alloyed steels containing Cr, Mo, Ni and Ti. was studied using hot torsion testing with the aim of modeling the recrystallization processes and the mean flow stress taking into account the microstructural behavior during hot rolling. The kinetics of static and metadynamic recrystallization were characterized and appropriate expressions were formulated for the recrystallization kinetics. These are shown that the recrystallization kinetics depend on steel composition and the processing conditions. The stress-strain curves were determined in order to derive new equations for the peak stress, peak strain, mean flow stress and softening kinetics. The peak strain is influenced by the presence of alloying elements; their addition, which has a solute drag effect, retards the rate of grain boundary motion, shifting the peak to the right. The addition of Nb to the steel results in a significant increment in the activation energy for hot deformation, and Mo has smaller effect than Nb, but Cr has the opposite effect. It was also found that the deformation activation energy in these steels was not altered by the addition of Ni. The rate of metadynamic recrystallization increases with strain rate and temperature and is observed to be independent of strain, in contrast to the observations for static recrystallization.The mean flow stress (MFS) calculations, based on the Sims analysis, are then compared with the predictions of a model based on an improved Misaka mean flow stress equation in which solute effects, strain accumulation, as well as the kinetics of static and metadynamic recrystallization are accounted for. Good agreement between the measured mean flow stresses, which is obtained from the mill logs of POSCO Kwangyang #3 HSM (hot strip mill), and 'predicted ones is obtained over the whole range of rolling temperatures. The results demonstrate that dynamic recrystallization followed by metadynamic recrystallization, supported by the unexpected load drops, sometimes occurs for the rolling schedules studied in the present analysis."

Jan 1, 2001

By In-Hyeok Choi

Currently, spent V2O5–WO3/TiO2 catalysts contribute significant amounts of solid waste following increasing levels of global demand. V2O5–WO3/ TiO2 catalysts usually consist of TiO2 anatase as a supporting oxide, vanadium as a catalytic agent, and other promoters such as tungsten, silicon, and calcium. Although vanadium is the main catalytic agent, a relatively high content of tungsten (WO3, 7–10 wt%) typically exists compared to vanadium (0.5–1.5 wt%). Considering the irreplaceable properties and industrial importance of tungsten, a feasible method for the recycling of spent V2O5–WO3/TiO2 catalyst should be established to utilize it as a secondary source. This paper presents a process to recover tungsten from spent V2O5–WO3/TiO2 catalyst. The processes proposed here involving roasting, decomposition using HCl, ammonia leaching, and crystallization. Within the process, ammonium paratungstate (71 wt% as WO3) is obtained as a final product. The total yield rate of tungsten from feedstock was found to be 96.3%.