Search Documents

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal, and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely. In this study, the failure energy partitioning of Nugget Sandstone specimens is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrate a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining-induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

Jul 1, 2020

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983

By Lana Alagha, Keitumetse Cathrine Monyake

The abstract discusses the synthesis and investigation of polyacrylamide functionalized chitosan polymers (CS-PAMs) as selective depressants for pyrite in the flotation of galena and chalcopyrite from complex sulfide ore. The study employed response surface methodology (RSM) to model and optimize the flotation process, varying parameters like the degree of deacetylation of chitosan, weight ratio of chitosan to acrylamide, and CS-PAM dosage. The developed RSM models effectively predicted iron and lead grades and recoveries, while optimization showed optimal pyrite separation from galena and chalcopyrite using CS-PAM synthesized from chitosan with a high degree of deacetylation and a specific chitosan:acrylamide weight ratio.

Apr 9, 2022

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By Yakup Cebeci, Leyla Kalender, Ceylan Yarluğkal Altınışık, Hikmet Sis

The abstract highlights the challenges in concentrating complex and non-sulfide lead-zinc ores and emphasizes the importance of froth flotation for their beneficiation. The study focuses on using process mineralogy to understand the flotation behavior of these ores from the Görgü region. The ore samples were characterized using various techniques, revealing oxidation and carbonation of primary minerals. The flotation results were interpreted in light of the mineralogical data, explaining the poor outcomes due to the complex nature of the ore, poor liberation, and lack of hydrophobicity.

Mar 22, 2022

By Oluwafemi Salami

Conducting full-scale fire experiments in underground mines is difficult and expensive. Sometimes, it is impossible to carry out fire tests in mines due to the danger they pose to mine workers and the underground facilities. However, understanding the potential occurrence of fires in a mine and their dynamics is critical to developing an appropriate emergency evacuation plan, fire suppression, and firefighting techniques. In this study, a numerical fire model using computational fluid dynamics (CFD) with fire dynamics simulator (FDS) 6.7.6 was developed to examine the influence of tunnel bifurcation on maximum temperature beneath a tunnel ceiling. The model was validated using full-scale experimental data. The maximum ceiling gas temperature predicted using FDS and measured maximum smoke temperature during the experiment shows good agreement. The study shows that bifurcation could lower the maximum ceiling temperature of fire-induced smoke in a subsurface environment. The findings from this study apply to the broader field of ventilation and fire life safety in tunnels and other underground environments.

Jun 23, 2024

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By L. B. McConville

The general term "tar sand" has been used to describe sand containing varying amounts of dense, viscous petroleum. Deposits of tar sands have been found throughout the world, often in the same geographical area as conventional petroleum. The largest one by far is known as the Athabasca Tar Sands, and is located in the province of Alberta, Canada. Actually a group of three deposits, these particular sands underlie an aggregate area of more than 12,000 square miles. Current estimates place the contained raw petroleum at about 700 billion barrels, from which as much as 300 billion barrels of synthetic oil may be recoverable under presently developed technology. For comparison, this latter quantity is roughly equivalent to five times the combined total of U.S. and Canadian crude oil reserves. With the ever-widening gap between energy supply and demand, attention is being directed to all possible energy sources - both developed and underdeveloped - and certainly the Athabasca Tar Sand deposit is one of the more important ones to merit such attention. This paper will review some of the more significant developments and attempt to place in perspective the role that this source of energy could possibly be expected to play in the foreseeable future.

Jan 1, 1974

By Fahimeh Dehghani, Louis Ackah, Tathagata Ghosh, Justin Godbold, Jia Liu, Meisam Peiravi, Manoj Mohanty, Azam Baharlouei

Primary economical deposits of rare-earth elements (REEs) are exhausting all over the world, and it has become necessary to find new sources and methods for their extraction. In addition, increasing the application of REEs in modern technological society has increased its demand globally. One of the important movements to compensate for the future shortages of critical metals is the recovery of REEs from recyclable materials. This paper presents a review of the classification and extraction methods, as well as general applications of REEs with emphasis on secondary sources such as coal and coal byproducts, iron ore tailings, apatite, and phosphate byproducts. An overview of the current state of knowledge on the various methods of REE beneficiation and extraction is covered. These methods include physical separation, as well as hydrometallurgical and bio-hydrometallurgical techniques. The application of these REE extraction techniques for enhanced recovery has been driven primarily by the unique industrial application of these important elements. This paper further explores the existing and potential environmental challenges associated with REE extraction. The authors have presented a wide array of literature, in-depth discussion of the subject, and a succinct summary of processes and relevant case studies.

Sep 23, 2020

By W. J. Kennedy

Energy management in industry has recently achieved notice as a way to reduce costs without decreasing production. The same approach used in industry can be used in mining, even though the processes are different. This approach is based upon a three phase system of data collection, implementation, and monitoring, all aimed at gathering and evaluating information in such a way as to have a maximum impact on energy costs. This approach has these advantages: (1) attention is directed toward the part of each mining system where the most energy is used, (2) input is collected systematically from all persons involved in the operation of each system, and (3) a means of monitoring the progress toward established goals is created. The mining systems considered are truck haulage, conveyor haulage, blasting and crushing, and lighting. After describing the general procedure, the authors have described a specific method for improving the efficiency (and hence the energy consumption) of round-trip truck haul age systems.

Jan 1, 1982

By Gary W. Hudiburgh

The gangue in some magnetite ore bodies contains feldspar; the alkali content of the feldspar reduces the usefulness of these iron ores. One method of decreasing the feldspar content in magnetite concentrate is froth flotation. The amine flotation of feldspar from magnetite concentrate was investigated using zeta potential measurements, Hallimond tube flotation tests and laboratory-scale flotation tests. The zeta potential of various feldspars (microcline, albite, anorthite, oliqoclase and anorthoclase) were determined as a function of pH; the point of zero charge ranged from pH 1.4 to 2.5. Hallimond tube flotation tests using two amine reagents were conducted on the feldspars. Hallimond tube flotation tests using six amine flotation reagents were performed on the cobber tails (quartz, albite and microcline) from a magnetite concentrating plant; in all cases, over 85 percent flotation recovery was obtained at pH 8 and 10-5 to 10-4 [M] collector addition. Laboratory-scale (667 grams) flotation tests were performed on the magnetite concentrate in an attempt to float the feldspar which had reported to the concentrate. The effects of three different collectors, two levels of collector concentration, three pH levels, starch and HF acid were investigated.

Jan 1, 1975

By Jon C. Yingling

Lean manufacturing, pioneered by Toyota, has been credited with the most significant improvements in production efficiency and product quality since the transformation from craft manufacturing to mass production in the early 20th century. It represents a comprehensive philosophy for structuring, operation, control, and management of production systems that is believed to have wide applicability. This paper outlines major lean manufacturing principles and discusses their potential for application in the mining industry.

Jan 1, 1999

By W. G. Lawrence

The rapid development of science and technology in Russia has been the result of well laid plans since 1918. At that time the Institute of Silicates was established is Moscow and later the establishment of similar more specialized institutes for the study of cement, glass, refractories, construction ceramics, electrical ceramics, building materials and asbestos provided the necessary research facilities for studies related to all types of ceramic inorganic materials. The' Institute of Ceramics and the Institute of Silicate Chemistry, Academy of Sciences, USSR, were founded in Leningrad. The work now going on in these various research' institutes covers every branch of silicate science and ceramics The impetus behind such establishment of special¬ized laboratories is no doubt due to the 5-year plans and the necessity of improving the scientific knowledge regarding the materials being used and the products being manufactured.

Jan 1, 1960

By Robert E. Ennis

Several important economic variables must be studied when planning a major underground conveyor haulage system if the objective of tow cost haulage is to be met. The purpose of this paper is to call these economic factors to the attention of the mine planner and encourage their serious consideration. To illustrate, the importance that some of these variables hole for the mine operator who wishes to reduce costs and maintain sound belt haulage practice, these areas of discussion will be covered. 1. Selection of economical flite lengths. 2. Economics of wire rope frame vs. rigid frame conveyors. 3. How idler design affects conveyor costs. 4. Economies in drive design. 5. How speed affects conveyor cost. 6. P.V.C. vs. Neoprene belt - what savings? 7. Maintaining, conveyor investment through maintenance. 8. Miscellaneous factors affecting the cost of belt haulage.

Jan 1, 1967

By P. L. Dunn

Automatic control of fine coal cleaning circuits has traditionally been limited by a lack of sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for on-line determination of ash content in fine coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73 ± 4% ash over a range from 65-90% ash. While this result is comparable to existing nuclear-based analyzers, the video-based system is only a fraction of the cost. The sensor is currently installed at the Middle Fork preparation plant owned by Pittston Coal Company.

Jan 1, 1997

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon capture and storage (CCS) is an attractive area of research in such fields as CO2 mineral carbonation, global warming and sustainable energy systems. In this study, carbonation efficiency for aqueous mineral carbonation (MC) was achieved through two steps,which include leaching of calciumfrom cement kiln dust (CKD) followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by the hydroxylation using NaOH. Response surface methodology (RSM) with a Box-Behnken design (BBD) was applied to optimize the calciumleaching yield,while the carbonation efficiency from CKD was assessed using RSMwith central composite design (CCD). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in MC and also influences and enhances carbonation efficiency. Different parameters including acid concentration (HNO3), leaching temperature, leaching time, and dose of CKD sample were considered in order to optimize the maximum yield of Ca leaching from the CKD sample. In addition, different CO2 flow rates and temperatures were used as parameters for optimizing carbonation efficiency. Two quadratic regression models were developed for each process, i.e. calciumleaching and carbonation. For calcium leaching, a maximum of 98.55% calcium was extracted under the optimal set of acid concentration 4.13 M, 90 °C, 28 min leaching time, and 13.8 g of CKD sample. For carbonation, the maximum carbonation efficiency of 89.2% was achieved for a CO2 flow rate of 1163 cm3/min at 90 °C. Calcium leaching results indicate that the leaching yield was significantly affected by all the input parameters except leaching time. For carbonation, both factors affected the carbonation efficiency, with the effect temperature shown to be greater than that of the CO2 flow rate. Additionally, the predicted results agreed well with the experimental values for both calcium leaching and carbonation processes, with errors of less than 1% and 5%, respectively.

Jun 5, 2020

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.