Search Documents

By M. J. Friedel

The U.S. Bureau of Mines (USBM) investigated the use of seismic refraction tomography (SRT) for identifying changes in pillar loading at the Foidel Creek coal mine near Steamboat Springs, CO. The inherent three-dimensional problem of directly imaging coal pillar conditions is reduced to a single plane by considering only the load transmitted from the pillar to the adjacent floor rock. Floor strata velocity tomograms (at two pillar locations) illustrate that loading conditions are non-uniform and non-unique. Also, time sequence monitoring, as the longwall face advanced, demonstrated that SRT can be used to image spatial changes in loading conditions. SRT offers the mining engineer a simple and flexible technique for evaluating pillar conditions, and thus, both present and alternative mine designs.

Jan 1, 1994

By G. L. Black

Choosing a mining method for an underground ore body is a complicated and often iterative process. Advances in technology give the design team an overwhelming array of possibilities for methods and equipment. Hecla's recent discovery of the deep Gold Hunter ore body has given the staff at the Lucky Friday Mine the exciting challenge of determining the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization, including drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of information as the project progresses through exploration and development.

Jan 1, 1998

By W. R. Sharp

The ability to target, delineate, excavate, and produce local resources is essential to the establishment of man's long-term presence in space. Many procedures and equipment utilized to mine resources here on Earth may be directly applicable on the lunar surface, while others may need extensive redefinition and development. This paper compares, for a lunar base, the alternative of burrowing into and below the lunar surface with that of surface mining. A conceptual underground mechanical excavator is presented.

Jan 1, 1991

By Satya Harpalani

The four most important parameters controlling the flow of gas in coal are the gas content, permeability, diffusion coefficient and cleat characteristics. Estimates of these and, more importantly, a knowledge about the variation in their values over time are required for simulation of long-term gas production. This paper describes experimental techniques to determine each of these, along with their time dependency, under simulated in situ conditions. It is shown that the permeability, diffusion coefficient and the cleat aperture values are not constant as usually assumed to be. There is a significant variation in their values as a result of changes in the microstructure of coal associated with release and flow of gas.

Jan 1, 1995

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By Zhiyuan Shen, Dan Zhao

The abstract discusses the importance of reliable mine monitoring systems for preventing accidents. It focuses on diagnosing ventilation system failures caused by roadway faults that alter airflow resistance. The paper proposes using an improved Support Vector Machine (SVM) method to identify the fault location based on changes in air volume detected by wind speed sensors. The approach involves building a sensitivity 0-1 matrix and establishing a roadway fault scope library. The improved SVM method is tested on the Daming coal mine, demonstrating its effectiveness in diagnosing fault locations, reducing training time, and improving accuracy compared to traditional SVM.

Apr 5, 2022

By Nik Sokol, Eric Sekulski, Leo Weiman-Benitez, Jon Hurt, Shrinidhi Vijayakumar, Phaidra Campbell

The Silicon Valley Clean Water (SVCW) Gravity Pipeline (GP) is the first Progressive Design Build (PDB) tunnel completed in North America. As part of the Regional Environmental Sewer Conveyance Upgrade (RESCU) Program, the tunnel is a key component to replacing and rehabilitating components of the existing conveyance system in San Mateo County, California. The GP consists of a large diameter Fiberglass Reinforced Polymer Mortar (FRPM) pipe installed inside a 4.1 m (13.5 ft) inside diameter, 5.3 km (3.3 mile) long precast concrete segmentally lined tunnel. The tunnel was constructed using a 4.6 m (15.2 ft) diameter Earth Pressure Balance (EPB) Tunnel Boring Machine (TBM) through heterogenous silts, clays and sands. Construction included two separate TBMlaunches from a centrally located access shaft, and a tunnel alignment below but in close proximity to very soft Young Bay Mud. Settlement criteria and mitigation strategies focused on protection of an existing 1.42 m (56 inch) diameter force main and adjoining structures along the alignment. This paper discusses the results of the theoretical settlement analysis versus the actual observed ground movements, while also presenting mitigation measures and adjustments made during tunneling to reduce the risks of adverse settlement.

Jun 13, 2023

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the National Institute for Occupational Safety and Health (NIOSH) developed a light-emitting diode (LED) area luminaire called the Saturn and conducted a laboratory study using a Fletcher High Dual-boom Mast Feed (HDDR) roof bolting machine. The Saturn luminaire was designed to (1) enhance floor illumination to enable better detection of trip hazards in the interior spaces of a roof bolter and (2) reduce glare that has typically been an issue of concern on roof bolters. This paper reports on the results of achieving the second objective. The existing roof bolter lighting was the baseline and was compared with three versions of the Saturn luminaire relative to light intensity (100%, 75%, and 50%). Discomfort and disability glare data were obtained from 30 participants that comprised three age groups. Discomfort glare perceptions were obtained using the De Boer rating scale, and disability glare was quantified by using Mars Letter Contrast Sensitivity tests. Discomfort glare was reduced at least 3 levels with all Saturn versions. Also, a predictive model was used to estimate discomfort glare, and the results were similar. Disability glare was the least for the Saturn’s 50% intensity, and all Saturn versions had significantly less disability glare than with the baseline lighting. Veiling luminance was calculated and used as another indicator of disability glare. Veiling luminance was 28 to 42 times greater with the baseline lighting as compared with that of the Saturn lighting. Lastly, visibility levels were calculated. The Saturn versions were 4 to 6.5 times better in terms of visibility level.

By Meghan M. Murphy, Derek Penrice

The Downtown Rail Extension (DTX) is principal element of the planned second phase of the Transbay Joint Powers Authority’s (TJPA) Transbay Program. When complete, this regionally critical project will connect Caltrain’s regional rail system and the California High-Speed Rail Authority’s statewide system to the Salesforce Transit Center in downtown San Francisco via a 1.3-mile tunnel. Studied since the 1970s, the DTX has now received environmental clearance, and key stakeholders are aligned on the project’s configuration and its expedited delivery. This paper describes efforts to optimize the DTX configuration and develop an informed project delivery strategy that incorporates construction industry feedback on project phasing, contract packaging, and procurement methods that accomplish the project’s budget goals.

Jun 13, 2021

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By Todd Minoski, Matthew McElhinney, Mark Mazzella, Morgan Sears, Craig Compton

The National Institute for Occupational Safety and Health (NIOSH) is staffed with Engineers, Geologists, and Field Technicians conducting a variety of ground control research. The mission of the ground control teams within the Mine Systems Safety Branch (MSSB) is to eliminate ground failures leading to mineworker injuries and fatalities. Advancing the science behind ground control relies heavily on conducting mutually beneficial research at participating mines which is detailed in specific references throughout the paper. The ground control teams have several types of field instruments at their disposal to measure the ground response in underground mines. These include borehole pressure cells (BPCs), vibrating wire stress meters (VWs), hollow inclusion cells (Hi-Cells), roof and rib extensometers, load cells, and convergence meters. These instruments are used to measure changes in pressure, strain, and displacement within the underground environment. Instrumentation data is collected automatically using intrinsically safe or MSHA permissible dataloggers if required. Information is transmitted to the dataloggers using approved cable to distances of 200–1,000 ft. depending on the type of datalogger being used. Once mining is completed, the dataloggers are retrieved and brought to the surface, providing in-mine data to mine management and engineers for the conditions currently being encountered in a particular mine. This data, in conjunction with geologic data and stress mapping, can be used to validate numerical models. The practical application of these models is extremely important for mine management and engineers, particularly when faced with more challenging mine environments. Insight gained from applying these models can be used to make better engineering-based judgments for areas that will be mined in the future. The impact of such applications can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 1, 2024

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By John Sasadi

The mining industry depends upon inexpensive water transportation. Today, large quantities of mined products are transported by ships over oceans, from continents to continents, over lakes and waterways to the ultimate users. Sometimes, the routes these Bulk Carriers travel cover only a few hundred miles, sometimes thousands of miles halfway around the world. Most of the products of the mining industries are relatively inexpensive. A significant portion of their cost to the ultimate users are in the cost of transportation and not in loading and unloading these commodities at the ports of origination or destination. So far, the industry has produced very efficient loading and un- loading installations, but has very little influence over marine transportation or the design of the vessels themselves. Very little was ever published dealing with integrated transportation systems properly correlating all phases of the operation; namely, loading, marine transportation and unloading bulk materials.

Jan 1, 1967

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By R. W. Chappell, M. W. Hills, R. L. Olsen

A stochastic approach was developed and applied to the Butte, Montana Hillside abandoned mining site for modeling stormwater runoff and subsequent receiving stream loadings. This approach enabled capture and quantification of the uncertainty associated with stormwater quality data and allowed the prediction of copper and zinc concentrations in the receiving stream caused by runoff from the Butte Hillside during storm events. Runoff flows and stormwater concentrations were input to the model as probability distribution functions. Monte Carlo simulation allowed prediction of expected instream concentrations in the form of cumulative distributions functions. The modeling results allowed evaluation of current best management practices (BMPs), targeting of future BMPs, and identification of key data gaps to fill during future sampling activities. This modeling approach is considered extendable to other active and inactive mining sites. Output from a model of this type is easily understood and can be used to communicate effective stormwater management to site regulators. Furthermore, application of this modeling approach will facilitate the development and implementation of a site-specific stormwater management plan and will optimize efforts to achieve standards for compliance with stormwater discharge permits.

Jan 1, 2002

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By D. Mohapatra

Extraction of Al(III) from aqueous sulfuric acid solutions into organic Cyanex 272®-carbon tetrachloride systems was investigated from a multi-component mixture containing aluminum, cobalt and nickel. Al(III) extraction efficiency was quantitative with 1.0 M Cyanex 272® in two stages at an aqueous: organic (A:O) phase ratio of 1:1 and an equilibrium pH of 3.2. The stripping of Al(III) from the loaded organic (LO) with different acids indicated sulfuric acid to be the best stripping agent. More than 99% stripping of Al(III) from the LO was achieved using 2 M H2SO4 at an A:O phase ratio of 1:1 in a single stage. The stoichiometry of the extracted species of Al(III) was determined by the slope analysis method. The extraction reaction proceeded via the cation exchange mechanism and the extracted species was assumed to be AlA3?3HA, where HA refers to the dimeric and A the anionic form of the extractant, Cyanex 272®. The extraction of Al(III) was studied in the presence of various ions to ascertain the tolerance limit of individual ions.

Jan 1, 2008

By K. V. Raj

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in open-pit mines is relatively new. Modeling the actual pit geometry of an open-pit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an open-pit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in open-pit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions, and turbulence modeling parameterization. An appropriate mesh selection is critical. A detail discussion of the meshing of the domain of an open-pit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (?-e), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an open pit and some of the approaches adopted to address these challenges.

Feb 27, 2013