Search Documents

By A. Tobey Yu

The smelter is the heart of a copper producing operation. Its principal function is to reduce and convert raw copper concentrates and/or leach plant precipitates into blister copper before it is refined. In addition to concentrates and precipitates, typical feed to a smelter also encompasses matte chips, flue dust, flux and lime. By nature, the characteristics of these materials are extremely variable, ranging from sub-micron to lumps, from slurry to dust, from abrasive to corrosive and free-flowing to adhesive. Furthermore, as a result of geological formation, most of the world's open pit copper mines are located in a semi-arid zone, where precipitation is minimal. This particular climate compounds the problem of handling these materials.

Jan 1, 1976

By G. A. Hufford

The cutoff grade applied to a disseminated orebody mined by open pit affects both the waste ratio, hence the cost of producing ore, and the ore grade, hence the quantity of metal recovered. As such it has a significant impact not only on the annual profit or loss, but also on the life of a mining property. Cutoff Grade Strategies Some commonly used objectives in calculating cutoff grades are as follows: Minimize Unit Cost of Product (1) This is found by adding all costs associated with each possible cutoff such as mining, processing, and marketing. This is divided by the quantity of marketable product obtained at each cutoff grade, then finding the minimum. Because the market value of the product does not enter the calculation it has no effect on this strategy: the same cutoff is selected in good times and bad.

Jan 1, 1986

By Gilman Y. Murray

The problems connected with the development of economically acceptable water supplies in arid regions are discussed. The techniques for capture and retention of runoff from infrequent desert storms are described and the major factors involved are emphasized. The exploration and planning for a typical water development in southwest United States is described, including an analysis of capital and operating costs for the proposed system.

Jan 1, 1963

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By M Aboagye, K Appau, W. Assibey-Bonsu, C. Muller

A case study based on two recoverable resource modelling techniques (indirect and direct or localised methods) have been derived using typical feasibility study or new mine drilling data configurations from the extensions of an existing mine’s massive production database. The database is from the Gold Fields Tarkwa Gold mine (~6Moz Mineral Reserves and 13-year Life-of mine). The corresponding recoverable resources from the various techniques are then analysed using the open pit Whittle optimisation process. The results were then compared based on the Whittle optimisation results to determine the efficiencies of the approaches and the validity of the recoverable mineral resource estimates for mine planning and financial forecasts (including Cash Flows etc). Based on historical production metal recovery, the paper also assesses the corresponding orebody and mine planning as well as financial risks with regards to the modelling techniques. The study shows that the localized direct and somewhat more straight forward approach if applied efficiently can provide an equally useful tool for computing recoverable resources for mine planning and financial forecasts, as compared to the indirect approach as presently in use.

Jun 25, 2023

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By Jeff LeBlanc, George Gutierrez, Carl Pitzer

The Bay Park Conveyance Project was one of the largest microtunneling and rehab projects in the United States at the time of completion. The completed project conveys treated water from the South Shore Water Reclamation Facility located in Nassau County, New York, which currently discharges an average of 50 million gallons per day (MGD) of treated water into Reynolds Channel, to the Cedar Creek Water Pollution Control Plant (WPCP) ocean outfall pipe. The pipe carrying treated wastewater was installed approximately 20–60 feet below the surface. The treated wastewater is conveyed via microtunnel construction of a 2-mile long force main from the South Shore Water Reclamation Facility to an existing aqueduct under the Sunrise Highway, the rehabilitation of an 7.3-mile stretch of the aqueduct via sliplining, and construction via microtunnel of a 1.6-mile-long force main to connect the rehabilitated aqueduct to the existing Cedar Creek Water Pollution Control Plant (WPCP) outfall, which discharges and diffuses treated water three miles offshore in the Atlantic Ocean. This paper will review the Design-Build requirements, the chosen innovative solutions during planning for the micro tunneling portion of the project and review the microtunnel construction on the project.

Jun 23, 2024

By F. Calizaya, S. Bhattacharyya

"INTRODUCTION Mechanized underground mines often suffer from noise overexposure. Noise levels are usually above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach 121 dB(A), especially when fans are not equipped with silencers. Use of silencers seldom ensure PEL for various reasons. Overexposure of noise induces permanent hearing loss among mine workers. Recent field studies by a NIOSH-funded research project at six coal and non-coal mines revalidated the findings. The University of Utah has undertaken laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material has been designed and tested. The silencer and an associated extension which can be repacked with different dampening materials were used in various configurations. Attempts were made to simulate field conditions where installations are quick and not perfect. The test results are presented here. NOISE IN UNDERGROUND MINES Noise induced hearing loss (NIHL) is a chronic problem in the mining industry. In spite of regulations being in place and elaborate hearing protection programs under way, hearing loss is prevalent among the mine workers (Bise, 2001). All production and support machinery in mining generate loud noise often beyond the approved exposure level. Researchers in the U.S. have identified auxiliary fans as one of the major sources of noise that can create noise exposure levels up to 121 dB(A), which is one of the highest in the mining operation (Bauer, 2006). Studies have demonstrated substantial reduction of noise level by using silencers. Adequate fan selection and proper utilization of silencers in auxiliary fans have great potential of abating the problem. In hard rock mines, auxiliary fans are used in blower configuration to ventilate development headings and large production stopes, and also to ventilate underground shops, crushers, conveyor transfer points, etc. Typical duct diameters in hard rock mines vary from 0.91 m to 1.21 m. Silencers are often omitted for cost reduction. In coal mines auxiliary fans are used in exhaust configuration with rigid ducts 0.61- 0.76 m in diameter (Hagood, 1982 and Moreby, 2009) to ventilate working faces in gate-roads and main entry developments. Sometimes, stone dusters are added at the discharge end to dust the roof, ribs and floor. AUXILIARY FANS AND SILENCERS Auxiliary fans are relatively smaller in size than the main fans and often have high rotational speeds (1800 -3000 rpm). Fans are selected based on pressure-quantity requirements and space restrictions only. Noise emissions are rarely considered during the selection stage. Installation of fans, ducts and other accessories is mainly based on best practices, which often do not include noise control. As a result, the operation of an auxiliary or local ventilation system normally produces excessive noise."

Jan 1, 2018

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Dionissios T. Hristopulos, Zach Agioutantis

Methane gas is emitted during both underground and surface coal mining. Underground coal mines need to monitor methane gas emissions to ensure adequate ventilation is provided to guarantee that methane concentrations remain low under different production and environmental conditions. Prediction of methane concentrations in underground mines can also contribute towards the successful management of methane gas emissions. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the USA. The AMS data were stored and pre-processed using an Atmospheric Monitoring Analysis and Database Management system. Furthermore, different statistical dependence measures such as cross-correlation, autocorrelation, cross-covariance, and variograms were implemented to investigate the potential autocorrelations of methane gas as well as its association with auxiliary variables (barometric pressure and coal production). The autoregressive integrated moving average (ARIMA) time series model which is based on auto-correlations of the methane gas is investigated. It is established that ARIMA used in the one-step-ahead forecasting mode provides accurate estimates that match the direction (increase/decrease) of the methane gas emission data.

Aug 2, 2022

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

By J. Kenneth Wittle

The DC Graphite Melter has been shown to be capable of processing radioactive waste materials. The process is characterized by its high temperature capability and operation in a closed system. From an environmental perspective, the control of emissions coupled with destruction for hazardous organic materials is mandatory. These same characteristics may be applicable to the minerals processing industry. Under normal operation, the system reaches temperatures for nominal operation of 1600°C, with an arc temperature in the order of 5000°C. The system temperature is determined by the melt temperature of the material being processed. In testing of a 750 lb/hour unit, temperatures of 2200°C were reached. Current focus is on finding waste treatment and metals recovery opportunities in the metals processing industry for his innovative technology.

Jan 1, 1999

By V. H. Forsythe

Mr. Chairman, members of SME, and guests It is indeed a pleasure to have the opportunity to appear before this group. The topic of this paper is, "Current Trends in Related Industries and Their Influence on Electric Shovel Design and Size". Before getting into the major items, it is well to point out that this text will deal with loading shovels primarily, since their application is almost universal in major open pit mining operations throughout the world. Related industries influence our design in many ways. For the sake of simplicity, these industries will be broken down into two major categories. The first category to be discussed will include industries that will indirectly influence design and size, while the second category will include industries whose products can directly be incorporated by the engineer in the design of shovels.

Jan 1, 1964

By D. E. Hulse

"Social License, the consent of the neighbors and community to develop and operate a mine, has received little attention until recently. Though social license is intangible, not having this relationship with the community carries operational and economic risk to a project, potentially including future impairment of the asset. Acquiring and maintaining social license is a long term personal relationship. It requires communication, commitment, consistency, and transparency. This presentation will review the building blocks to acquire and maintain a social license based on experiences with mining projects in Mexico. INTRODUCTION Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them” (Agricola 1556). In 2015 it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate. “Most commonly, the SLO is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders.” (Bice 2014) A generation ago I learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three legged stool is a very stable structure.In 2015 it seems that we have added some other legs to the stool. The JORC code addresses “social, and governmental factors” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves”. The Canadian CIM Guidelines refer to “environmental, legal and social data” (CIM 2003).Compared to these the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the Competent Person."

Jan 1, 2016

By D. W. Hendrickson

Cliffs views the process as extending from mine planning to cargo loading including auxiliary systems such as material handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This paper discusses the development and results of a strategy to allow and promote implementation of process automation improvements at individual mines based on their economic priorities taking advantage of common systems and concepts for use at multiple mines where practical. Specific process control upgrade projects a Hibbing Taconite Company and the Empire Mine are reviewed in detail.

Jan 1, 1998

"The seventh annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held last February at the SME Annual Conference & Expo in Phoenix, AZ. A total of 21 students entered the poster competition. The students were required to submit one-page abstracts, which were reviewed by the judges, after which they prepared posters to display their work. A panel of judges went to each student and listened as the student explained his/her research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. Recognizing the effort required to participate, the MPD provided monetary rewards to all participants. First place received $1,000; second, $500; and third through seventh, $200. All remaining entrants received $100 each. The winners have their abstracts published in this issue of Mining & Metallurgical Processing. As in past years, there were separate levels of competition for undergraduates and graduates.Now for the winners:Graduate winnersJoseph Halt won first place for research on the use of additives to starch binders to create iron ore pellets. Vivek Agarwal received second for working on using solvent extraction to concentrate lanthanum. Jordan Rutledge placed third for utilizing tannins to depress calcite in fluorite flotation. Fourth through seventh places were Vu Truong, Jacob McDonald, Hunter Sceats and Doug Schriner.Undergraduate winnersLaura Nugent won first place for using high-frame-rate cameras to follow bubbles as they moved from the pulp to the froth in flotation cells. Taylor Graham earned a second-place finish by researching how to acid leach low-grade manganese carbonate.Although its cliché to say everyone’s a winner, everyone can benefit from attending the MPD Student Poster contest. All the students were able to display their work to potential future employers, and industry professionals could talk to the up-and-coming engineers. Next year, there will be another competition for more posters and networking, so get ready to attend.Thank you to all the students for participating; Lisa Schlink for chairing the session; the judges, Aaron Noble, Debra Switzer, Mohammad Rezaee, Nick Gow and Ren Bryce, for evaluating the abstracts and posters; and the MPD sponsors for supporting the competition. This has only been successful with the input of all three groups. Engineering iron ore pellets to reduce their dustinessJ.A. Halt and S.K. KawatraGraduate student and professor and chair, respectively, Department of Chemical Engineering,Michigan Technological University, Houghton, MI, USAIntroductionIron ore pellets are hard spheres made by agglomerating iron ore concentrate and binders. Pellets are the preferred ironbearing feed for blast furnace ironmaking. Starch has been proposed as a binder because it has good adhesive properties, does not contaminate pellets and is relatively cheap. However, starch binders typically lead to weak pellets with rough surfaces, and these can cause high levels of dust within process equipment and when pellets are handled and shipped (Halt and Kawatra, 2014). Our research shows that by adding a small quantity of other additives, pellets made with starch binders become smooth and strong. The newly designed binder leads to significantly lower levels of fines when pellets are handled."

Jan 1, 2016

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. Coteau, a wholly owned subsidiary of The North American Coal Corporation, produces more than 13.5 million tonnes per year, ranking it among the largest mines in North America. In 1993, Coteau ranked seventh in terms of annual coal sales, becoming the largest mine outside the Powder River Basin of northeastern Wyoming. However, for the Freedom Mine to stand among these Powder River heavyweights, Coteau over-came several obstacles, including a coal seam with three quarters the heating value and overburden to coal ratios three times higher than the Powder River mines. Coteau's ability to compete has been built around a program of continuous productivity improvement, cost efficiency, and innovation. This report highlights a few of the major improvements implemented in recent years.

Jan 1, 1995

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992