Search Documents

By T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of backmixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically made very tall, on the order of 30-40 feet, in order to limit the effects of backmixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug-flow. In this work, horizontal baffles were shown to improve the performance of a 6-foot tall laboratory-scale flotation column treating a difficult-to-clean, heavily oxidized coal. Tests with variation in the position of the baffles showed that for the greatest benefit, baffles are needed both above and below the feed inlet. Tracer tests with a fluorescent dye water tracer showed that the addition of the baffles reduced the amount of feed water entrained into the froth at any given coal recovery.

Jan 1, 1994

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By D. H. White

The term "block caving" as used in this text includes panel caving and mass caving as described by Julin and Tobie (1973). This method reportedly was conceived in 1895 when a block of ore ranging up to 200 ft (61 m) in width was undercut at the Pewabic Mine on the Menominee Range in Michigan (Bucky, 1956). Over the years this method has evolved largely as a consequence of trial and error in which operators became acutely aware of what nature would allow and what it would not. Today block caving remains somewhat of an art rather than a science where experience often dictates what needs to be done. With the plunging prices of base and specialty metals in the early 1980s caving mines sought to reduce operating and development costs in order to return to profitability. For some this became an impossible task given the design, grade and operating costs of the day and closure became the only alternative. One lesson learned from the experiences of the 80s is that survivability depends on cost competitiveness and this implies the efficient use of resources and technology. To this end applied rock mechanics serves as a useful tool. The purpose of this paper is to show how Geomechanics can be used? in block caving to facilitate sound decision making and how this equates to dollars saved. Features of mining method selection, design and operation are discussed as related to this theme.

Jan 1, 1990

By G. L. Simmons

Aqueous pressure oxidation at low temperature, although desirable from a process engineering and operations point of view, presents unique problems when temperatures approach 160°C (320°F). In developing the pressure oxidation process for the Lone Tree Mine, elemental sulfur formation and agglomeration with pyrite proved to be a problem. This paper discusses some of the unique features of the Lone Tree sulfide deposit and its amenability to low temperature oxidation. Problems encountered during pilot plant operation and their solutions are discussed.

Jan 1, 1993

By Kate Willa Brown Requist, Eric Lutz, Moe Momayez

As air quality sensor networks become increasingly popular in underground coal mines, it is important to generate paradigms for the application of the collected data. To date, air quality sensing has been primarily used as an early warning system for hazardous air conditions. Using data collected from a network of sensors in a US underground coal mine, we have created multiple visualization methods to show the interactions of carbon monoxide evolution with ventilation airflow. These visualization methods can allow for further analysis of the source of contaminant, as well as better data resolution across the area of concern within the mine. By utilizing univariate spatial interpolations, we present methods for identifying the movement of carbon monoxide at one-minute intervals. The resulting visualizations display the evolution of carbon monoxide concentration across a sizeable study area over a period of 14 minutes.

Jun 25, 2023

By Ernesto Maldonado, Zach Agioutantis, Jesus Romero

Reliable prediction of dynamic deformations is important when planning to undermine important structures that cannot tolerate large relative deformations and or large horizontal strains. This paper presents examples of dynamic deformation profiles that include subsidence, horizontal displacements, and horizontal strain for a number of points over a retreating longwall panel in the eastern United States. The prediction points are located at different distances from the excavation rib and therefore present a different response in terms of dynamic movements. The formulation is based on the influence function method as implemented in the Surface Deformation Prediction System (SDPS). Results show that the subsidence development curve may be reliably predicted for surface points in the middle of the panel. However, in cases where points may be affected by the magnitude of the edge effect offset, subsidence predictions may be very conservative, that is, higher than actual movements.

Jul 1, 2023

By Thomas A. Wheeler

The reagents commercially used in coal flotation and their roles are reviewed and discussed According to their function the reagents are divided into often overlapping groups: 1. Collectors 2. Frothers 3. Conditioning Reagents Frothers have by far the largest effect on the amount of coal recovered They act not only in their traditionally accepted function of “bubble makers”, but in coal flotation they serve in a seldom acknowledged role of collectors. A lab flotation study on four samples of different coal ranks shows how these react to various frother families and proves that no froher is the optimum reagent for all types of coal. The advent of new technology in flotation equipment in the past decade has resulted in various novel designs of column cells, Jameson and Centrifloat™ cells, air-sped hydrocylones, etc. All should require special frothers or blends of frothers to meet their specific needs.

Jan 1, 1994

By Frank McKinley

This paper discusses the basic requirements covering the area between the initial discovery of a deposit and a decision as to whether or not the deposit will support an economically sound mining venture. The procedure for gaining the necessary information and the sequence of steps is in .some respects parallel to gaining like information on deposits other than the sand type. For the sake of simplicity the stages and sequence are presented as follow: first, the initial reconnaissance drilling; second, the exploration drilling to permit initial ore body estimates; third, metallurgical testing; fourth, the estimate of plant and operating costs; and last, the economic balance. The objective of the reconnaissance drilling is to collect sufficient information to reach a decision as to the advisability of further exploration or the abandonment of the area. This initial phase will comprise, in addition to some drilling, a thorough reconnaissance of the area, a study of the best geological and topographic maps of the region, and a study of any literature available, all under the guidance of a geologist.

Jan 1, 1958

By Juan Camus

To understand why some companies excel in creating value, Jim Collins (2001) and a group of postgraduate business students engaged in a comprehensive, five-year research project. They examined 1,435 U.S. companies for more than 40 years, seeking those that made significant improvements in their financial performance over time. The distinctive pattern sought was: ?Fifteen-year cumulative stock returns at or below the general stock market, punctuated by a transition point, then cumulative returns at least three times the market over the next 15 years. ?The search identified 11 outperforming companies, all in different industries, that were called the ?good to great? companies. To contrast these companies with similar peers within the same industry, the search also selected a group of comparison companies that failed to make the leap from good to great. Collins then set out to examine the transition point. What distinguishing features did the good-to-great companies have that their industry counterparts did not? At the heart of the findings about these outstanding companies is what Collins refers to as the ?hedgehog concept? ? how to find the one big thing that the company must focus on. According to Collins, those who built the good-to-great companies were, to one degree or another, hedgehogs. Those who led the comparison companies tended to be foxes, never gaining the clarifying advantage of a hedgehog concept, being instead scattered, diffused and inconsistent. This insight is complemented by Peter Drucker (2004), an influential management guru, who asserts that the first question an effective executive should ask is: ?what needs to be done?? Asking this question and taking it seriously, he asserts, is crucial for managerial success; and that the answer almost always has more than one urgent task, but the effective leader only concentrates on one task. In this last respect, Drucker emphasizes: ?If they [executives] are among the sizeable minority who work best with a change of pace in the working day, they pick two tasks. I have never encountered an executive who is effective while tackling more than two tasks at a time.?

Jan 1, 2011

By Wayne S. Cavender

The geochemical association of arsenic and gold in epithermal precious metal deposits of the Basin and Range province is well documented, and in this paper I wish to discuss the evaluation and utilization of this element association for geochemical gold exploration. In 1961-62, I conducted an exploration program on lands controlled by Getchell Mine, Inc, and centered about the Getchell gold mine itself, Besides exploring for new gold deposits, the program was to evaluate these lands for potential deposits of any type; thus, a multi-phase program encompassing a number of exploration methods was conducted. I shall not elaborate on the process of designing the program or of integrating the various methods, but for gold exploration, geochemical methods were determined to have the best potential. This paper is based on that effort. Figure 1 shows the exploration area, which covers the northern half of the Osgood Mountains in eastern Humboldt County, Nevada. The Getchell $line is on the east flank of the range and is about 40 miles northeast of Winnemucca.

Jan 1, 1964

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960

By R. R. Godard

The practice of dust abatement or control is not new to any operation of United States Steel Corporation. This report will review those activities, past and present, within the five operating districts of United States Steel-Coal Operations with specific reference to mechanical and continuous mining, and including both the health and safety aspects of the problem. Obviously, the first principle of dust control is to inhibit its formation If this is not practical, steps may be taken to prevent its becoming airborne. Airborne dust control can be realized by either collecting it at the point of generation, diluting it with large volumes of air to reduce concentration, settling it by various means, or with reference to ignition hazard only, render it incombustible by neutralization with an inert material. These basic principles have been verified by the work of many, including the Bureau of Mines, U. S. Department of Interior, Bituminous Coal Research, Inc., and the Mining Research Establishment of the National Coal Board of Great Britain. Their application to every day mining problems is best illustrated by the following examples.

Jan 1, 1967

By Joseph W. Mullan

The today status of air pollution control legislation and regulations can best be described as an exaggerated state of environmental limbo. The '70's began but one and one-half months ago yet it already has been very appropriately named "the decade of the environment." This certainly will be the decade for new legislation - new regulations and hopefully "Clean Air." Already Washington is faced with legislators playing "pollution politics" to the crowds. Students have redirected their efforts from Vietnam to the cleansing of the environment and everyone including the man on the street has become an environ¬mental expert. This is the decade we all face, but where are we today? Pollution is not a new problem. It has been with us for centuries and while much is left to be done, much has already been accomplished. I will try to make some comparisons of what I believe to be the good and bad points in the national air pollution control picture and hopefully will generate within each of you sufficient concern as to which comparisons are sound.

Jan 1, 1970

By T. Reed Scollon

Major interrelated factors to be considered in assessing the impact of air pollution control regulations on coal are: (I) the fuel and fuel-related limitations of such regulations; (2) the rate of adoption and areal scope of the regulations; and (3) the availability of fuels and fuel-burning equipment to meet the requirements. A growing number of regulations contain provisions limiting the emissions of sulfur oxides or the sulfur content of fuels or both. With few exceptions, these limitations have not yet become fully effective in those areas which have already adopted regulations, and pertinent details of future regulations or legislation for most other areas are unknown at this time. Sufficient information is not avail- able to determine the availability of low-sulfur fuels at various demand and price levels, and large-scale commercial feasibility of sulfur-oxides removal processes and equipment is believed to be some years away. Accordingly, with the many uncertainties and unknowns, it is possible at best to make only a rough assessment of the impact of such regulations or legislation on coal.

Jan 1, 1969

By R. Fernando

"The Office of Mine Safety and Health Research (NIOSH-OMSHR) currently is leading an effort in the development of the next-generation self-escape apparatus as part of the research imperative directed by the MINER Act of 2006. A multifaceted contract program over the past 3 years delivered key components and base breathing modules to form the basis for developing backpack and vest-style versions of dockable self-contained (closed-circuit) self-escape respirators with hoods (CCMERs). This paper outlines the current status in developing the CCMER that incorporates a docking and switch-over valve (DSOV) for seamless transfer from one breathing device to another, and a hood with an inner mask and speech diaphragm (HMC) for ease of donning, ease of use, and communication ability. Three versions of the CCMER are being pursued, namely: the CCMER-B, which can be worn as a backpack and incorporates the features of a miner’s belt; the CCMER-V, which is worn similar to a miner’s vest and attaches to a miner’s belt; and the CCMER-C, a breathing module cached along the escape route that can be docked to the -B and -V versions. Human factors considerations are a key element in the CCMER design, as it is to be continually worn by the miner while underground, and must be readily accessible for deployment when needed. The CCMERs are designed to be capable of being certified to 42 CFR part 84 standards, including sub-part O for mine use, and to meet MSHA permissibility regulations for use in underground mines. They are sized for sufficient oxygen capacities (Cap 2 and Cap 3 as defined in sub-part O) to yield a duration that is of practical use in a mine escape scenario. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) is leading the development of self-escape apparatuses to provide breathing gas to mining personnel operating in the event of an emergency in various capacities underground in environments containing hazardous gas components. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) and input from the mining community called for the need to move Self-Contained Self-Rescuer (SCSR) technology to a next-generation status. In response to this need, NIOSH’s Office of Mine Safety and Health Research (OMSHR) established a strategic plan to develop key components and devices with help from external experts knowledgeable in breathing apparatus designs. The US Navy was identified as a key expert in this field through its extensive experience in diving apparatus and life support systems, and development work commenced through Inter-Agency Agreements with OMSHR. A contracts program was also launched with industry experts specializing in this field. This paper outlines the current status in developing the Next-Generation Closed-Circuit Mine Escape Respirators (CCMERs) that could be used for surviving and escaping from a mine following an emergency that renders the mine atmosphere irrespirable."

Jan 1, 2016

By G. Davis

It is well known that the anticipated mineral price at the start of a prospective mineral project can have an overwhelming effect on a property's ex ante value. However, possible price movements throughout the life of a project can also have an impact on this value. This paper demonstrates how different potential price paths can affect project value. When considering commodity price projections for mine valuations, it is thus necessary to estimate not only the expected commodity price at the start of the project, but also the manner in which that price is likely to fluctuate throughout the project's life.

Jan 1, 1995

By P. R. Taylor

The ability to treat refractory gold concentrates that contain appreciable amounts of sulfur and arsenic, in an economic and environmentally safe manner is important to the gold mining industry. Processing alternatives include: autoclave oxidation, bacterial oxidation and roasting. Roasting may be the cheapest of all the alternatives if inexpensive methods can be found to contain the arsenic and sulfur. The research program, being reported here, has been evaluating the ability to use hydrated lime in the roaster to capture both the arsenic and the sulfur. Lime roasting is not a new idea, it was proposed for copper ores by Bartlett in the early 1970's (Bartlett and Haung 1973) and for cobaltite concentrates by Taylor in the early 1980's (Taylor et al., 1981). In addition, ores have been roasted that contained limestone and it was shown that partial capture of the sulfur was possible. Lime -sulfur containment has been proposed for the coal fired electricity industry, as well.

Jan 1, 1992

By Georgene Renner, Chee Theng, William Gleason

"In February 2018, drawn in part by the states’ proud mining heritage, SME took its Annual Conference & Expo to Minneapolis, MN for the first time. More than 5,000 people and 554 exhibitors converged on the Minneapolis Convention Center for three days of networking, exhibiting and technical sessions.The state’s mining legacy, one that continues today, is fueled in large part by its vast iron ore resources in the northern part of the state. The historical significance of the mines in the Mesabi Range, otherwise known as the Iron Range north of Lake Superior, cannot be understated. “Mining is a way of life here,” said U.S. Congressman Rick Nolan of Minnesota’s 8th Congressional District. A native of the Iron Range, the three-term U.S. congressman was one of the featured speakers of the opening keynote session. “We like to think we contribute enormously to the well-being of this country and the world. We were the source of the iron ore and steel that helped win two world wars. And we like to think that we are part of the progress that has taken place in the United States ever since.” Nolan kicked off the keynote sessionthat focused on innovation and its part in the mining industry. The session included Rene Aquilar, vice president of corporate affairs and sustainability, Antofagasta Minerals Group; Bob Anderson, vice president for research and development, 3M; Rolf Weberg, executive director, Natural Resources Research Institute, University of Minnesota-Duluth and Christopher Beck, executive vice president and president, Nalco Water. The panel session looked at U.S. and global minerals production, and the importance of the United States to maintain a major role in the minerals industry, both as a producer and as a technology leader. The panel also touched on the global mining industry and the issues that impact mining around the world. Sustainability, the use of water in mining and earning a social license to operate were among the topics discussed by the panel.Speaking of the importance of mining, Nolan conceded that talking about the benefits of mining to the crowded auditorium at the SME conference might be akin to a preacher speaking to the choir, but, following the adage that all politics are local, he continued to illustrate his point by emphasizing the importance of mining to the Great Lakes.“A study by Homeland Security concluded that 13 percent of the nation’s GDP comes out of Lake Superior through the locks at Sault Ste. Marie and most of that is iron ore,” said Nolan. “That study found that, if those locks fail, it would create a national depression. It would put millions of people out of work. That ore and those minerals supply the steel mills, the auto industry, the heavy industrials. They are the heart of our economy. The study concluded that if the states that make up the Great Lakes were a nation, it would be the fourth largest economy in the world.”"

Jan 5, 2018

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023