Search Documents

By M. R. Geer

Three coals from the Wilkes on - Carbonado district of Pierce County , Washington , were subjected to washability analyses to estimate the amount and quality of washed coal obtainable . Because the coals were unusually difficult to clean , the washability examinations were supplemented by table tests , tests in dense - medium cleaning units , and flotation tests . None of the coals could be reduced to the desired 10 percent ash by tabling and the response to flotation by two of them was poor . Dense -medium treatment provided coal of the desired quality , but with the most difficult coal the recovery efficiency was lower than usual .

Jan 1, 1964

By R. E. Siemens, Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites . The process consists of four mmaajjoorr steps : ( 1 ) reduction roast , ( 2 ) ammoniacal leach , ( 3 ) solvent extraction , and ( 4 ) electrowinning . Several solid - liquid separation steps are required that affect the economics of the overall process . In this study , two techniques for solid - liquid separation , centrifugation and thickening , were investigated . This report presents the results of ( 1 ) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and ( 2 ) an economic study of the two techniques , based on the requirements of a commercial - size ( 5,000 - tpd ) laterite processing plant . Sizing and other equipment - related recommendations , based on data from the Bureau's studies , were obtained from commercial manufacturers . The costs of thickening and centrifugation , including all the unit operations affected , were determined by the Bureau's process evaluation group . The total operating costs for separation using the two techniques ( including depreciation on the capital cost of equipment ) were found to be quite close : $ 17.26 per ton of laterite for centrifugation and $ 18.15 per ton of laterite for thickening . For centrifugal separation , the greatest cost was found to be the initial capital cost for the separation equipment ; using thickeners , the greatest cost was for reagent recovery .

Jan 1, 1983

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Representation of actual oil yields from sections of the Green River formation oil shales by two types of drill - cutting samples was evaluated . Average oil yields of single sets of mud cuttings from hydraulic rotary drilling in Colorado and gas cuttings from pneumatic rotary drilling in Utah were compared statistically with yields of core samples taken from adjacent holes . Oil yields from gas cuttings were identical to oil yields of core samples . Mud cuttings appeared to represent a section of the formation conservatively , the deficiencies increasing with increasing richness of sample . Because a large amount of the oil - yield data currently available for the Green River formation is based on mud- cutting samples , development of a valid correction method by additional testing is needed .

Jan 1, 1963

By G. L. Bartlett

"INTRODUCTION The major objective of our research is to help reduce the incidence and severity of coal worker's pneumoconiosis (CWP). To that end, this project is designed to improve our understanding of the processes that lead to pulmonary dysfunction following mine dust exposure, and how those processes might be interrupted or attenuated. The response of the lung ' to inhaled particles is complex, and the course of development of disabling CWP is slow and unpredictable. From among the numerous cellular and molecular interactions involved in the pulmonary response to inhaled particles, this project is focussed on the role that the pulmonary alveolar macrophage (PAM) may play in regulating the activity of fibroblasts.The PAM is the lung cell that has the most immediate and the most obvious interaction with inhaled particles. Within a short period after particles are arrested in the alveolus of the lung, they are phagocytized (engulfed) by these specialized cells. The PAM then has a diverse potential repertoire of subsequent activities. Which reaction actually ensues is determined, in large part, by the nature of the phagocytized _particles. Activated PAMs produce a variety of products that may affect adjacent lung tissue, including superoxide free radical, elastase, collagenase, prostaglandins, platelet activating factor, etc. Those may well be important in the pathogenesis of CWP, but they are beyond the scope of this project. Background information that is cogent to this project has come primarily from investigations using animal models of silicosis and asbestosis. PAMs that have ingested silica particles synthesize and release molecules that control the behavior of surrounding cells. One such mediator is interleukin-1 (IL-1), a molecule that plays a central role in many aspects of the response to injury. It can stimulate fibroblasts (the cells that help to hold tissues together) to release the enzyme collagenase, resulting in breakdown of the structural collagen fibers that support the lung tissue. IL-1 also stimulates fibroblasts to undergo mitosis and to proliferate, which is an initial stage of fibrosis. Certain stimulants cause PAMs to release fibroblast growth factors (FGFs) that are distinct- from IL-1. Under other circumstances activated PAMs synthesize and release molecules that stimulate fibroblasts to accelerate synthesis of collagen fibers, thus contributing to fibrosis. Although these observations provide a valuable precedent for analysis of the mechanisms involved in CWP, their relevance to CWP cannot be assumed since most of those studies involved macrophages or fibroblasts obtained from tissues other than the lung, and because almost none of them have used CMD as the stimulating particles. Therefore, the goal of this project is to learn how exposure to CMD affects the behavior of PAMs, and in turn how products of dust-exposed PAMs affect fibroblasts and the process of fibrosis in the lung."

Jan 1, 1988

By D. C. Seidel

This report describes generic procedures and equipment arrangements for conducting laboratory-scale hydrometallurgical and related waste-management experiments. It provides a starting point for personnel who have received or are receiving professional training, but do not have specific experience in laboratory procedures. With guidance, it also has application as a resource for technician training. The publication contains chapters on laboratory safety, feed-sample preparation, leaching, solids-liquid separation, and recovery from solution.

Jan 1, 1995

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

This dictionary is published by the Bureau of Mines as a contribution to the mining and mineral literature in the belief that it will fill a recognized need. Several attempts have been made over the years to revise Albert Fay's Glossary of the Mining and Mineral Industry which first appeared in December of 1918. Frank L. Hess of the Bureau of Mines worked on a revision, but his untimely death prevented its completion. Subsequently, the writer was employed to compile and edit this dictionary in cooperation with the technical staff of the Bureau of Mines. Fay's glossary contained about 18,000 terms with 27,000 definitions; the present compilation contains about 55,000 terms with approximately 150,000 definitions. These terms are of both a technical and local nature, and they apply to metal mining, coal mining, quarrying, geology, metallurgy, ceramics and clays, glassmaking, minerals and mineralogy, and general terminology. Petroleum, natural gas, and legal mining terminology, unless of a general nature, has been excluded, as has been foreign terminology where there is an English equivalent. Several thousand Spanish-American mining terms that appeared in Fay's compilation have been removed to make way for the thousands of new English terms that have evolved over the years. Those Spanish-American and Mexican terms still used in the Southwestern United States have been retained.

Jan 1, 1968

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

By Raymond B. Ladoo

The uses for which ground talcs are suited closely depend upon their physical and chemical properties , but , in spite of this fact , little scientific investigation has been made in order to devise quick and accurate tests for the determination of these properties . The chemical properties of talc are inherent and may not be altered or modified except by selective mining or by chemical processes not practical in the present status of the industry . However , the determination of chemical properties is not so important , for most uses , as of physical properties , although sometimes certain chemical characteristics are perhaps unduly insisted upon by chemists in some industries . Physical properties are dependent both upon mineralogical characteristics and upon methods of grinding and sizing and may thus be partly changed or modified by changes in practice . There is so little known of the chemistry and physics of the various processes in which talc is used that the purchase and sale of talc is governed more by rule- of- thumb methods dependent upon individual opinion and often , prejudice , than by accurate , standard tests . This not only causes unwarranted price fluctuations , but injures both the producing and consuming industries by creating false ideas of the suitability of talc for various uses . It thus seems important that present tests be standardized and made uniform for the whole industry , and that new tests devised to fill the existing gaps .

Jul 1, 1920

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

By E. D. Gardner

Oil shale, a long-considered potential source of motor fuel in the United States, is found over an extensive area in the Green River formation in Colorado, Utah, and Wyoming.4/ Oil has been retorted commercially from shale in Scotland for many years,5/ and work done by the Bureau of Mines and other investigators has shown that it is technically feasible to extract oil from American shales.6/ By refining, the shale oil may be converted into marketable products similar to those manufactured from crude petroleum. The present paper, which was finished in 1936, discusses methods that would be adaptable to mining certain American shales, and the treatment applies specifically to conditions iii the Green River formation on Naval

Jan 1, 1942

By D. Harrington

The mining industry of the United States has-long been severely criticized because of its high rate of accident occurrence, net only as compared with other major industries-in the United States but also with the mining industries of other countries particularly Europe. Statistics (often not of strictly comparable nature) indicate that the accident-frequency rate in all mining is currently about three times and the accident-severity rate is about seven times as great as the average for general industrial work in the United States. These figures are by no means comforting to humanitarian mining men, irrespective of their status in. the industry, and they constitute a challenge that certainly cannot continue to be ignored much longer. This picture becomes much darker when the above statistics are augmented with data indicating that. on an exposure basis our mines (more particularly our coal mines) have accident rates two, three, or even more times as great as more or less similar types of mines in Europe, particularly England and Wales, Belgium, France, and Germany. However, these foreign accident statistics should be carefully analyzed before we become very mush concerned about them, because they are clot strictly comparable owing to several considerations, not the least of which is the fact that foreign methods of compiling or recording accident statistics often differ materially from ours. Moreover, foreign mining and other conditions axe definitely dissimilar to ours in many if not most phases, and numerous ether factors affect the comparability of foreign mine-accident statistics with ours. Unquestionably it should also be taken into consideration that the accident rate of the 130,000,000 or more constituting the populace of the United. States as a whole is much higher than that of any other major country in the world and is two, throe, or more times the rate of the European countries that have more favorable mine-accident rates than those of the United States. Moreover, it is significant that the mine-accident-severity- rate of British mines is about six times the average accident-severity rate of the major industries of the British Isles, or but little mere, favorable than the comparable figures in the United States, namely, that mining-has an accident-severity rate about seven times that of the average of about 30 of the major industries of this country.

Jan 1, 1941

By Charles W. Perdue

This U.S. Bureau of Mines report considers, from a psychological perspective, the perceptual process by which miners recognize and respond to mining hazards. It proposes that if the hazard recognition skills of miners can be improved, mining accidents may be reduced to a significant degree. Prior studies of hazard perception in mining are considered, as are relevant studies from investigations of military target identification, pilot and gunnery officer training, transportation safety, automobile operator behavior, research into sensory functioning and visual information processing. A general model of perception is introduced, and selected concepts from the psychology of perception that are applicable to the detection of mining hazards are reviewed. Hazard recognition is discussed as a function of the perceptual cues available to the miner as well as the cognitive resources and strategies employed by the miner. The development of expertise in responding to hazards is related to individual differences in the experience, aptitude, and personality of the worker. Potential applications to miner safety and training are presented.

Jan 1, 1995

By H. A. Watson

This circular, which is a revision and combination of two previous publications,3 4/ presents information on the different types of equipment that may be used to analyze mine atmospheres, with particular reference to the application and limitations of each type. Such information is frequently requested by mining companies, State mining departments, and other agencies concerned with safety in mining who wish advice regarding methods of analysis of mine atmospheres and the equipment necessary for establishing laboratories for that purpose. Since the Haldane-type apparatus is particularly applicable to the accurate determination of carbon dioxide, oxygen, and combustible gases such as methane in mine atmospheres, that apparatus and the method of operation are described in detail. The circular presents results of a critical study of the accuracy attainable with the Haldane-type apparatus in the determination of methane in concentrations of the order of 0.25 percent, by volume. Analytical procedures involved in the other methods discussed are presented in publications referenced in this circular. Information is given also on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres, and suggestions on laboratory design are included. INTRODUCTION 'The analysis of mine atmospheres plays an important part in promoting safety and maintaining safe conditions in mining operations, particularly in coal mining, where the flammable gas methane presents a continuous hazard in Nome mines and may be encountered unexpectedly in others.5/ Methane has been encountered also, often unexpectedly and with disastrous results, in noncoal mines and in tunnels under

Jan 1, 1956

By M. J. Gavin

Within the past three years numerous inquiries for information on oil shale have been received by the Bureau of Manes. These inquiries have been increasing to such an extent that it has seemed advisable to issue a short paper prior to the publication of a bulletin on the subject, giving a, general discussion of the subject and a comprehensive list of references, so that those interested in the details of obtaining oil from shale can find additional information without much difficulty. Some of those who desire information are interested only in a general discussion of the subject, or are not in a position to refer to books and' articles describing the industry. The material for this paper is largely derived from published information on oil shale. Much of the information is obtained-from the books and articles mentioned in the list of references, and has been compiled with the intent of furnishing information to those not interested in all the details.

Jan 1, 1921

By Jr. Gabler

Because of concern over the availability and reliability of an uninterrupted supply of manganese and other materials, the U.S. Congress requested that the U.S. Bureau of Mines (USBM) study the /low of strategic and critical materials in the economy to delineate and quantify the production areas where metal values are lost. As a result, the USBM developed a generic computerized commodity flow model that is readily amenable to updating. The original model developed for cobalt, with slight modifications, was used to track the flow of manganese. This report follows the flow of manganese through its metallurgical and chemical applications and highlights areas where significant losses occur owing to downgrading, export, or disposal. The study indicates that materials containing 695,000 short tons (st) of manganese were consumed domestically in 1990. Scrap recovery specifically for manganese recycling was insignificant. However, considerable manganese was recycled through processing operations as a minor component of ferrous and nonferrous scrap and steel slag. The major loss category is manganese lost in steel processing, 323,156 st or 46 pet of the 1990 apparent consumption. Most of this loss reports to steelmaking slags. Recovery from slags is technically feasible, but is not economically feasible.

Jan 1, 1995

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By Reinhardt Thiessen

"INTRODUCTION Coal is a complex substance consisting of many different constituents representing many chemical compounds, very few of which are known. It is homo genetic, however, in that it is derived almost entirely from plants. But plants as a whole are complex, being composed of a large number of tissues, each consisting of a large number of cells in a great number of arrangements and composed of a number of chemical compounds in great variety of proportions, and enclosing a large number of waste products representing a large number of' chemical compounds as cell contents. Coal should therefore be expected to be a very complex substance.That coals are formed from plants is no longer debated, but the manner in which coal was formed from the plants leaves many problems still unsolved. However, in general it is now conceded that all coals of all ranks and ages had their origin in deposits completely analogous to our peat deposits of today and that coal formation is a process that runs through the whole series, beginning with peat, and through, the various ranks of lignite, subbituminous, high-, medium-, and low-volatile bituminous, semianthracite, and anthracite in a related chain. In the study of coal, it is therefore of the utmost importance to study and to know not only the plants contributing but .also the manner in which they are transformed into the substances forming the deposits. It is therefore of the greatest value to review briefly the formation of :,eat as it is known today, and to inquire into the facts as to what plants contribute to peat, what parts and products prevail, what are the chemical compounds that enter and which prevail."

Jun 1, 1947