Search Documents

By Charles W. Merrill

AN ADEQUATE, dependable, and continuing supply of raw materials is indispensable to tile the United States and its industries in meeting the needs of an expanding Population, a rising standard of living, and the national security. The primary responsibility for appraising the status of the country's mineral supply and for making appropriate recommendations within the executive branch and to the Congress has been pinned in the U.S. Department of the Interior. In fulfilling its role of governmental responsibility for raw-material supplies and their efficient utilization, the Bureau of Mines has analyzed the factors in current and future mineral supplies and demands and has developed 87 statements for specific commodities that assess the national position and problems for these metals, minerals, and mineral fuels. These statements, which constitute the chapters of this volume, are based on lire assumption that nearly till production and consumption of materials in the United States are to be by private individuals and organizations, in accordance with the Nation's devotion to a private-enterprise economy.

Jan 1, 1960

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

By Charles Prasky

This report describes fluidized bed techniques employed by the Bureau of Mines at Minneapolis to differentially sulfatize the manganese in two samples of low-grade manganiferous ferruginous carbonate slates from the Cuyuna Range district, Minn. Suitable mechanics of operation were established. A space rate of 1.25 to 1.5 fps, a retention time of 3 to 3.5 hours, a temperature of 700° C, and a 10 percent sulfur dioxide gas in air were adequate for sulfatizing the slates by fluidization. Under these conditions the overflow product removal rate from the 4-inch-diameter reactor was 4 to 5 pounds per hour. The sulfur dioxide was used more efficiently in the two-stage treatment than in the single-stage treatment. However, approximately 80 percent of the manganese was converted to sulfate by either treatment.

Jan 1, 1963

By C. G. Kirkpatrick

Analysis of the data produced by a wide-band, sensitive, horizontal, biaxial motion sensor has revealed several distinctive patterns before, during, and after a roof fall. The signals prior to the roof fall are similar in spectra, but one thousand times larger in amplitude, than those after the roof fall. Immediately preceding the roof fall, by two to twelve hours, five events occurred which were larger in amplitude and lower in frequency than even the large pre-roof fall background signals. An interpretation of these events is offered.

Jan 1, 1979

By D. A. Reynolds

Yields of ammonium sulfate obtained in the carbonization of coal frequently vary from plant to plant, because ammonia is an unstable compound at high temperatures and therefore sensitive, to changes in carbonizing conditions. Differences in byproduct yields of ammonium sulfate obtained at different plants generally are accounted for by variations in plant procedure, either in preparing the coal or in its carbonization. However, technicians of one large corporation,- which frequently obtained higher yields of ammonium sulfate in its Alabama plants than ever were attained in its Ohio plants, "could not reconcile the differences in yields with their plant operations. These investigators suspected that the Alabama, coal used in their southern plant yielded more ammonia because its composition differed inherently from that of the Pennsylvania and West Virginia coals fused in their Ohio plants, although this concept could not be proved readily in their large-scale operations. Their view is supported by experimental data obtained A Beau of Mines-American Gas Association (BM-AGA) carbonization tests) -21 of a large number of coals including those carbonized commercially in Alabama and Ohio.

Jan 1, 1949

By R. J. Heemstra

A continuous flowing paper electrophoresis cell was used to separate petroleum and petroleum extracts into characteristic patterns. The electrophoresis of Bachaquero, Lagunillas, Boscan, and Gibson petroleums in nitro-benzene and acetic acid-based electrolytes was investigated. The extent of separation in the patterns was studied by measuring the metal and porphyrin contents of the effluents. Qualitative separations were achieved in some systems, whereas either system demonstrated only a high degree of electrophoretic migration.

Jan 1, 1967

By Floyd D. Everett

The Cougar Spar property is in southwestern Beaver County, Utah, approximately 35 miles by road northwest of Lund, a station on the mainline of the Union Pacific Railroad (fig. 1). Original fluorspar discoveries on the property were made a. short time before 1941. During 1941 lessees produced approximately 600 tons of ores averaging 40 percent CaF2. Bureau of Mines engineers examined the property in 1942 and recommended development. Work was begun in December 1942 and completed in October 1943. The area was mapped by members of the Federal Geological Survey during the project period. Development included surface trenching; drifting, and crosscutting, a short distance below the outcrop. The surface work comprised a total of 440 linear feet of bulldozer and hand trenches. A total of 550 feet of workings was driven on the 100-foot level. Samples were taken for assay from the trench exposures and from the underground workings as work progressed. Pocks in the area of the Cougar Spar property are igneous and consist mainly of fine-grained tuff and quartz monzonite porphyry. The fluorspar mineralization occurs in a northwest fault zone.

Jan 1, 1951

By Vincent Castranova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

"A group of bisbenzylisoouinoline alkaloids has been shown to exhibit various degrees of effectiveness in preventing silica-induced fibrosis in animal models [1, 2]. The objective the present study was to characterize the binding of several of these alkaloids to phosphatidylcholine vesicles and rat alveolar macrophages using fluorometric and equilibrium dialysis methods, respectively. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, chiral configurations, and double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is a highly effective agent in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, certain analogues of tetrandrine such as curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In conclusion, the results of these studies indicate that alveolar macrophages exhibit large binding capacities for certain members of this class of bisbenzylisoquinoline alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds. These data also suggest that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.INTRODUCTIONInhalation of crystalline silica is associated with the development of silicosis. This fibrotic disease is characterized by the appearance of concentric hyalinized nodular lesions in the lungs with the progressive development of pulmonary dysfunction [3, 4]. Many theories concerning the etiology of silicosis involve silica-induced activation of alveolar macrophages. Evidence indicates that in vitro silica exposures result in the generation of chemiluminescence, and the release of superoxide and hydrogen peroxide from alveolar macrophages [5]. Activation of alveolar macrophages has also been demonstrated after intratracheal instillation or inhalation of silica [5, 6]. Such excess release of reactive products from pulmonary phagocytes has been associated with damage to the lung parenchyma [7, 8]. In addition, silica exposure results in the release of mediators from alveolar macrophages, which enhance proliferation of fibroblasts and collagen synthesis by these pneumocytes [9-12]."

Mar 1, 1992

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By Donald A. Voigt

This publication is intended as a guide for persons responsible for obtaining classifications and approvals Tor explosive compounds, mixtures, or devices from the U.S. Department of Transportation (DOT). It deals with the procedures for obtaining a recommendation for classification of an explosive compound, mixture, or device through the Bureau of Mines. Completion of the procedures detailed in this guide is necessary to obtain a final classification of an explosive compound, mixture, or device and assignment of an "EX" number by DOT, which will allow the producer to offer the explosive for shipment within the United States. This guide also gives procedures for obtaining United Nations (U.N.) classification for shipping outside the United States.

Jan 1, 1990

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By Walter K. Utt

The vibration levels of the heavy machines used in surface mining are much greater than for vehicles used on highways. In order to assure the proper functioning of electronic equipment placed on the surface mining vehicles, the U.S. Bureau of Mines has conducted a program of field measurements to define their vibration environment. The information in this report is for a class of vehicle that has a blade for scraping and wheels with rubber tires. The statistical information derived from these measurements can be used as a basis for laboratory testing to qualify equipment for a surface mining vehicle of this class. The envelope that would encompass 99 pct of the vibrations encountered in normal operations is presented for each location on the vehicle. The five locations for which data were recorded are the floor of the cab, the engine, the frame, the drive train (gear, differential, and torque converter), and the axle. Tabulated data are provided for those who wish to use a different probability level. The appropriate test profile for the laboratory testing can be determined from the information presented in this report.

Jan 1, 1993

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By W. A. Stickney

The Bureau of Mines conducted beneficiation and smelting studies on siliceous offgrade manganese samples to indicate effective methods of manufacturing silicomanganese from materials that cannot be economically beneficiated to meet General Services Administration (GSA) specifications for stockpiling. Laboratory and pilot-plant flotation tests were conducted on 2 samples, 1 from the waste-tailings dump of the Domestic Manganese & Development Co , Butte, Mont., and the other from the Nettie mine in the Butte-Philipsburg area. Smelting tests were made on the combined concentrates from the pilot-plant flotation tests and on part of the tailings sample The flotation scheme found to be adequate in laboratory tests and later in the pilot-plant tests consisted of flotation by a fuel oil-tall oil emulsion in an acid circuit (pH )-1-.8 to 5.0). The oil-emulsion reagent flocculated the manganese minerals and selectively floated them from the siliceous gangue, In the pilot-plant flotation test on Butte-mill tailings 90.1 percent of the manganese was recovered in a concentrate that analyzed 32.6 percent Mn, 4.8 percent Fe and 28.1 percent Si02. In the test on Nettie mine ore 90.8 percent of the manganese was recovered in a concentrate that analyzed 36 6 percent Mn, 5.5 percent Fe, and 26-4 percent Si02.

Jan 1, 1956

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923

By Martin J. Gavin

"Before discussing oil shales it may be well to consider briefly the conditions surrounding the petroleum industry in the United States, because these largely explain why so much interest is being manifested in oil shales. The United States is not only the greatest producer of petroleum in the world, its output amounting to about 65 per cent of the world's total production; but is also the world's greatest consumer, using more petroleum than it produces within its own borders. For the past four or five years it has been necessary to import oil at a continually increasing rate to make up the deficit between domestic production and domestic consumption. Experts who have made a close study of the future supply and demand for, crude petroleum are satisfied that under present production practice and with the development of possible undeveloped productive areas, the gap between domestic consumption and production will steadily .increase.As possible solutions for the impending domestic shortage of oil, various expedients are receiving attention. These may be grouped under three heads, as follows:(1) Temporary measures, such as curtailment of consumption, development of more efficient methods of production, and more efficient utilization of supplies of petroleum still available. It is unlikely that there will be any great curtailment in consumption of petroleum in the United States; rather, consumption will continue to increase unless a real shortage of oil actually forces curtailment of consumption. The other two possibilities mentioned deserve, and are resolving, serious thought. Much experimental work along these lines, some of which has already yielded excellent results, is being done. Obviously, however, any of these remedies are temporary ones only, so far as regards domestic production of petroleum."

Oct 1, 1920

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966